GemTek Technology WAPD246ACN WAPD-246ACN_LoRa gateway User Manual

Gemtek Technology Co., Ltd. WAPD-246ACN_LoRa gateway Users Manual

Contents

Users Manual

WAPD-246ACN LoRa Gateway User Manual Version : 1.0.1
Release History Release Data Release Version Description Author 2017/08/04 1.0.1 Initial release William Huang
Gateway Configuration Access gateway Administration Web GUI at :8080 port http://x.x.x.x:8080/ Default Username/Password : admin/admin If it is the first login, it will ask you to update the default account You may configure the account as admin/Admin123 After login, Dashboard page shows System Info. Firmware Version can
be checked at here. Go to “LoRa Module Status” to check band setting Go to “ABP Setting” page to configure ABP setting
(ex. 12345678 / 12345678123456781234567812345678 / 12345678123456781234567812345678) Go to “Payload Broker Setting” page to check MQTT related settings
User can use “GIOT-GW/UL/+” to subscribe all the uplink data.
LTE setting ## Power-off and insert SIM card ## ## Power-on and Enable LTE function via Admin GUI ##
After login, go to WAN setting to enable LTE (input PIN code if needed) and press “SAVE”
## Unplug PoE Adapter’s “DATA IN” port to let device switch from ethernet to LTE ## By default, device use ethernet to connect to internet. Unless PoE Adapter’s “DATA IN” port is unplugged, device will switch to use LTE.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA.
Professional installation instruction Please be advised that due to the unique function supplied by this product, the device is intended for use with our interactive entertainment software and licensed third-party only. The product will be distributed through controlled distribution channel and installed by trained professional and will not be sold directly to the general public through retail store. 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited. 4. Installation procedure Please refer to user’s manual for the detail. 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty.

Navigation menu