Go Networks WLP-1100F-580 Wireless LAN Access Point User Manual GO MBW 1100 WLP Installation Guide
Go Networks Inc. Wireless LAN Access Point GO MBW 1100 WLP Installation Guide
User Manual
Document # 1100-30-000-A04 Feb 17, 2007
GO MBW 1100 (WLP)
Installation Guide
GO MBW 1100 (WLP) Installation Guide
GO MBW 1100 (WLP) Installation Guide
Trademarks and Licensing Agreement
© 2006-2008 GO Networks, Inc. All rights reserved.
All information contained in this document is protected by international
copyright treaties. No information may be copied or reproduced without the
express written consent of GO Networks Inc.
GO Metro Broadband Wireless, GO MBW, WLAN Sector Base Station, WLS, GO
WLAN Pico Base Station, WLP, GO Wireless Network Controller, and WNC are all
trademarks of GO Networks Inc.
Any duplication, transmission by any method, or storage in an information
retrieval system of any part of this publication for other purposes other than
those stated above is strictly prohibited without the specific written permission
of GO Networks, Inc. This includes, but is not limited to, transcription into any
form of computer system for audio, text, print, or visual retrieval. All rights
under federal copyright laws and international laws will be strictly enforced.
All other trademarks and registered trademarks are the property of their
respective owners.
GO Networks Inc.
1943 Landings Drive • Mountain View, CA 94043 • USA
Tel +1.650.962.2000 • Fax +1.650.962.2010
Email support@gonetworks.com
GO MBW 1100 (WLP) Installation Guide
FCC Compliance Status
The following information is for FCC compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential environment, this
equipment generates, uses, and radiates radio frequency energy, and if
not installed and used in accordance with the instructions, may cause
harmful interference. However, there is no guarantee that interference will
not occur.
To meet regulatory restrictions, the outdoor access point must be
professionally installed.
The Part 15 radio device operates on a non-interference basis with other
devices operating at this frequency when using its antennas. Any changes
or modifications not expressly approved by GO Networks could void the
user's authority to operate the equipment.
The antennas used for this transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
GO MBW 1100 (WLP) Installation Guide
Table of Contents
Introduction ........................................................................................................................................ 1
Key Product Features ................................................................................................................................ 1
Organization of this Document ................................................................................................................... 2
GO MBW 1100 (WLP) .......................................................................................................................... 3
MBW 1100 (WLP) Package Components .................................................................................................... 3
MBW 1100 (WLP) Safety Information .......................................................................................................... 4
RF Exposure .............................................................................................................................................. 4
MBW 1100 (WLP) Lightning Protector ....................................................................................................... 4
Information de sécurité pour MBW 1100 (WLP) ......................................................................................... 5
Exposition aux fréquences RF ................................................................................................................... 5
Paratonnerre pour MBW 1100 (WLP) ....................................................................................................... 5
Installation .......................................................................................................................................... 6
Installation Process ...................................................................................................................................... 6
Site Survey ................................................................................................................................................ 6
Assembling and Mounting ........................................................................................................................... 7
Mounting Brackets ..................................................................................................................................... 9
Mounting the MBW 1100 (WLP) .............................................................................................................. 12
Mounting the Antenna .............................................................................................................................. 13
Cable Connections ..................................................................................................................................... 14
Cable Installation Tools............................................................................................................................ 16
Grounding Cable ...................................................................................................................................... 17
Ethernet Connection ................................................................................................................................ 18
Power Connection ................................................................................................................................... 18
Console Connection ................................................................................................................................ 19
Power Up and Software Configuration ..................................................................................................... 20
Appendix A: List of Acronyms ........................................................................................................ 21
Appendix B: Wiring Specifications ................................................................................................. 23
- Page 1 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Introduction
GO Networks’ MBW 1100 (WLP) device is a key enabler for the Metro
Broadband Wireless (MBW) Solution. GO Pico Cellular WiFi architecture
offers a novel topology for metro WiFi networks, which relies on the
strengths of innovative XRF™ architecture. This architecture provides the
coverage, capacity, and scalability required to deliver next-generation
services and overcome the limitations of existing metro WiFi solutions.
The GO Networks’ Pico Cellular WiFi architecture is a highly scalable
Micro/Pico topology which provides unprecedented flexibility to service
providers deploying Metro WiFi networks.
Key Product Features
Robust Pico cellular WiFi solution
Separate access & backhaul radios delivering unmatched bandwidth
xRF™ smart antenna engine for unmatched (360o) coverage and
capacity enhancements
Advanced automatic mesh
Designed for streetlight, wall, or pole deployment
Client/WDS based CPE connection
Support for all standard security scheme
- Page 2 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Organization of this Document
The GO MBW 1100 Installation Guide for the Wireless LAN Pico Base
Station (WLP) offers information and instructions for quickly installing and
configuring the MBW 1100 (WLP). The instructions and information are
presented in one volume as follows:
Introduction
Contains introductory information about the
MBW 1100 (WLP).
GO MBW 1100 (WLP)
Presents a general description and overview of
the MBW 1100 (WLP) including content and
safety procedures.
Installation Process
Describes the installation process for the MBW
1100 (WLP).
Appendix A
Lists the acronyms that appear in the manual.
Appendix B
Details the wiring specifications.
- Page 3 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
GO MBW 1100 (WLP)
The GO MBW 1100 (WLP) complements the MBW 2100 (WLS). It delivers
street-level coverage and provides capacity enhancements in dense metro
areas over a single 802.11b/g channel, while meshing traffic over an
802.11a radio.
The MBW 1100 (WLP) Base Station delivers omni-directional (360o)
coverage while retaining full xRF smart antenna engine functionality for
enhanced capacity and range.
MBW 1100 (WLP) Package Components
The MBW 1100 (WLP) package items are listed in Table 1:
DESCRIPTION
REV
QTY
Wall/Poll Mount Kit Assembly (new)
1.0
1
Connectors Kit for MBW 1100 (WLP) Package
1.0
1
MBW 1100 (WLP) unit
1.0
1
MBW 1100 (WLP) Access Antenna 2.4GHz 7.4dBi Gain,
Omni
4
802.11a 5Ghz 8dBi Omni Mesh Antenna
1
802.11a 5Ghz 8dBi Omni Mesh Antenna
(For models MBW 1100F Triple-Radio and
MBW 1100E Triple-Radio only)
1
802.11a 4.9Ghz 8.5dBi Omni Mesh Antenna
(For model MBW 1100F - HLS (4.9) only)
1
Power Connector with cable length of 6 ft (180cm)
1
Antenna Support Plate
1
Table 1: MBW 1100 (WLP) Package Contents
- Page 4 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Deployments of gateway devices connected by wire to an indoor
switch/router would include installation of a lightning protector. A lightning
protector is not supplied as part of the standard package. It can be
ordered from GO Networks as an accessory.
Specific installation may require different Power/Ethernet connections. See
Cable Connections for more details.
MBW 1100 (WLP) Safety Information
RF Exposure
The MBW 1100 (WLP), an outdoor access point, is compliant with the
requirements set forth in CFR 47 section 1.1307, addressing RF Exposure
from radio frequency devices as defined in OET Bulletin 65. The outdoor
access point antennas should be installed to provide a separation distance
of at least 3 feet (1 meter) from humans.
MBW 1100 (WLP) Lightning Protector
A lightning protector is required when the MBW 1100 (WLP) unit is
installed in an outdoor location and the Ethernet cable connects to an
indoor network device.
The purpose of the lightning protection is to protect people and equipment
located indoors from lightning that might strike the MBW 1100 (WLP) or its
outdoor cables. Therefore, the lightning protector device should be
installed indoors, as close as possible to the point where the cables enter
the building.
The lightning protector can also be installed outdoors, as long as the
cables that go from the lightning protector to the indoors are well
protected from lightning between the box and the building entrance.
Verify that you have shared grounding. GO Networks offers a lightning
protector that can be ordered separately.
- Page 5 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Information de sécurité pour MBW 1100
(WLP)
Exposition aux fréquences RF
Le point d’accès extérieur MBW 1100 (WLP) est compatible avec la norme
CFR 47 section 1.1307 concernant l’exposition aux appareils émetteurs de
fréquences radio RF définis par le Bulletin 65 de l’OET. Les antennes
doivent être installées à une distance minimum d’un mètre de personnes
humaines.
Paratonnerre pour MBW 1100 (WLP)
Un paratonnerre est nécessaire lorsque le point d’accès MBW 1100 (WLP)
est installe à l’extérieur et lié à un network intérieur par un câble Ethernet.
La fonction du paratonnerre est de protéger les personnes et équipement
situés en intérieur des éclairs qui pourraient frapper le MBW 1100 (WLP)
ou son câble extérieur. Par conséquent, le paratonnerre doit être installé
en intérieur le plus près possible du point où le câble de liaison pénètre le
bâtiment.
Le paratonnerre peut aussi être installé en extérieur à la condition que les
câbles a l’intérieur du bâtiment soient protégés des éclairs entre le point
d‘accès et l’entrée du bâtiment
Vérifier que la prise de terre est partagée. GO Networks met a disposition
à la vente un paratonnerre.
- Page 6 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Installation
Installation Process
Installing the WLAN Pico Base Station involves the following steps:
1. Performing a Site Survey
2. Assembling and Mounting
3. Mounting the MBW 1100 (WLP) unit
4. Connecting the Antennas
5. Connecting the cables
6. Powering up the unit and configuring the software
7. Performing a Post-installation Testing Procedure to verify
connectivity and operation
Site Survey
Most wireless LANs include many access points installed in various
locations in an overlapping radio-cell pattern. It is important to carefully
identify each access point’s position and the assignment of its radio
channels. Therefore, a site survey becomes an essential first step before
physically deploying the MBW 1100 (WLP).
Installation of the access points requires a backhaul to interface the
corporate network or Internet. This backhaul connection can be a mesh
configuration, an Ethernet-wired connection, or a third-party solution.
When using any method other then a wired connection, keep in mind the
MBW 1100 (WLP) has to have a good reception on its BH side so it will not
limit the access-channel performance.
Conclude the site survey with a detailed plan of the MBW system
deployment. The system deployment plan should include MBW 1100 (WLP)
mounting points and the routes for the power and backhaul cables.
Note:
Since the mounting structure itself is a potential source of
interference, the cell should be mounted with at least 4 feet of
clearance between the antennas and the mounting structure.
- Page 7 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Assembling and Mounting
The universal mount is used to attach and secure the MBW 1100 (WLP) to
a wall, a streetlight arm, or a variety of poles.
The MBW 1100 (WLP) mounting consists of the following stages and should
be performed in the following order:
1. Connect the MBW 1100 (WLP) unit to the brackets using the ‘L’
adaptor.
2. Secure the mounting brackets to a streetlight arm, wall, or pole.
3. Assemble the MBW 1100 (WLP) unit to the bracket.
4. Ground the MBW 1100 (WLP) unit.
5. Align the MBW 1100 (WLP) unit.
6. Mount the Antenna to the MBW 1100 (WLP) unit.
Table 2 lists the universal mount parts:
Item
No.
Description
Qty
Picture
A
Wall/Poll Bracket
1
B
Clamping Bracket
1
C
MBW 1100 (WLP) ‘L’
Adapter Wall/Poll Mount
1
D
Hex Bolt M8x70
2
E
Hex Bolt M8 x25
1
F
Flat Washer M8
3
G
Spring Washer M8
4
- Page 8 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Item
No.
Description
Qty
Picture
H
Nut M8
1
I
Antenna Support Plate
1
Table 2: Mounting Kit Part List
Hardware and Connectors Installation Tools
The following tools are required to mount the MBW 1100 (WLP) on a pole.
Description
Picture
Combination Wrench (13 mm)
13 mm
Table 3: Mounting Tools and Equipment
Note: All hardware and tools used for assembling and mounting the
MBW 1100 (WLP) are Metric.
To assemble the ‘L’ adaptor [C] to the MBW 1100 (WLP) unit:
Attach the ‘L’ adapter to the MBW 1100 (WLP) using an M8 x25 hex
bolt [E], a spring washer [G], and a flat washer [F], as illustrated in
Figure 1.
- Page 9 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
"L" Adapter
Hex Bolt
Flat Washer
Spring Washer
Figure 1: Mount ‘L’ Assembly
Mounting Brackets
To secure the mounting brackets:
1. Select an optimal mounting location on the pole. Select the highest
mounting location with minimal obstacles to the antennas for
optimal performance.
NOTE: When mounting the MBW 1100 (WLP), the pole or wall
mounting must support a minimum of 61.6 lbs (28 kg).
In addition, the pole or wall mounting must support the
wind loads from the MBW 1100 (WLP), e.g., 24.2 lbs
(11 kg) for wind velocity of 100 mph (160 km/h),
66.1 lbs (30 kg) for wind velocity of 165 mph
(264km/h).
Noter: Lorsque vous montez la MBW 1100 (WLP), le poteau ou
le montage mural doit supporter d'un minimum de 61.6
lbs (28 kg). En outre, le montage sur le poteau ou sur
le mur doit appuyer les surcharges dues au vent de la
MBW 1100 (WLP)(par exemple, 24.2 lbs (11 kg) pour la
vitesse du vent de 100 mph (160 km/h),66.1 lb (30 kg)
pour l'énergie éolienne Vitesse de 165 mph
(264 km/h)).
2. Installation of the mounting brackets to a streetlight arm or a pole
differs according to the width of the pole, as illustrated in Figure 2.
- Page 10 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Narrow pole
1"-1.75" Normal pole
1.75"-3" Large pole,
greater than 3"
Figure 2: Pole Bracket Assembly
3. For narrow poles (1”–1.75” diameter):
a) Place the two brackets, [A] and [B], around the pole at the
approximate height where you wish to place the unit. When
placing the clamping bracket [B], the small notch side should
be in contact with the pole.
b) Use two M8x70 hex bolts [D] and spring washers, insert them
through both brackets and tighten them around the pole so
that the two brackets are securely fastened.
4. For normal poles (1.75”–3” diameter):
a) Place the two brackets, [A] and [B], around the pole at the
approximate height where you wish to place the unit. When
placing the clamping bracket [B], the large notch side should
be in contact with the pole.
b) Use two M8x70 hex bolts [D] and spring washers [G], insert
them through both brackets and tighten them around the
pole so that the two brackets are securely fastened.
5. For poles larger than 3” in diameter:
a) The wall/poll bracket [A] and two 0.5" (13mm) wide stainless
steel hose clamps (not supplied with mounting kit) are used.
The hose clamps must be the appropriate size to fit around
the pole and bracket.
b) Open the each hose clamp by rotating the screw on the clamp
counterclockwise. There may be additional resistance just
before the clamp is completely open. This is normal and you
should continue rotating the screws until the clamps are open.
- Page 11 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
c) Insert the band of each clamp through both slots and over the
bracket [A].
d) Place the bracket [A] and hose clamps around the pole at the
approximate height where you wish to place the unit.
e) Close each clamp by reinserting the band under the screw
and rotate the screw clockwise.
f) Position the bracket in the appropriate location and tighten
the clamps around the pole so that the bracket is securely
fastened.
6. For wall mounting:
a) Fasten the wall/poll bracket [A] to the wall using four 3/16”
(5mm) bolts, as shown in Figure 3. Use the appropriate bolts
and fasteners, which is dependent on the material of the wall.
Wall-mounting bolts and fasteners are not supplied with the
mounting kit.
b) Place the wall/poll bracket [A] at the appropriate location
where you wish to place the unit. Using the four holes at the
corners of the bracket, mark the location where the fasteners
need to be installed.
c) Install the four fasteners in the wall.
d) Insert the four bolts through the bracket and securely fasten
the bracket to the wall.
Wall Mounting Holes
Figure 3: Bracket Wall Mounting
- Page 12 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Mounting the MBW 1100 (WLP)
To mount the MBW 1100 (WLP) unit:
1. After assembling the brackets, mount the MBW 1100 (WLP) unit on
to the bracket as shown in Figure 4. Use a flat washer [F], a spring
washer [G] and a nut [H].
WLP Unit
Bolt
Flat Washer
Nut
Spring Washer
Figure 4: MBW 1100 (WLP) Unit Mounting
2. Once the MBW 1100 (WLP) unit is mounted, release the bolts
slightly and align the MBW 1100 (WLP) unit horizontally using the
level, as shown in Figure 5. When the unit is perfectly aligned, firmly
close all bolts, applying 120 inch-lbs of torque.
Figure 5: Aligning the MBW 1100 (WLP)
- Page 13 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Mounting the Antennas
The MBW 1100 (WLP) supports six antennas. Four WiFi antennas used for
user access, which operate on the 2.4 GHz band, marked A1 to A4. Two
antennas are used for the mesh networking connections, marked B2 and
B3.
To mount the antennas on the MBW 1100 (WLP):
1. Attached the four 2.4 GHz band antennas to terminals A1 to A4 and
screw all antennas into place by hand. Rotate each antenna at its
metallic base. The antennas should rotate easily. Tighten the
antenna by hand only. Do not apply excessive force by using any
tool, as this may damage the unit.
2.4 GHz
Antennas
Terminals
A1-A4
Figure 6: 2.4 GHz Band Antennas Installation
2. Insert the four 2.4 GHz band antennas into the Antenna Support
Plate. The antennas must be inserted evenly, so that the plate is
level and all the antennas are protruding the same. Use caution not
to change the alignment of the MBW 1100 (WLP).
Antenna
Support Plate
2.4 GHz
Antennas
Figure 7: Antenna Support Plate Installation
- Page 14 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
3. Attach a 5 GHz band antenna to terminal B2. Tighten the antenna
by hand at its metallic base. The antenna should rotate easily. Do
not apply excessive force by using any tool, as this may damage the
unit.
Terminal B2
5 GHz
Antenna
Figure 8: 5 GHz Band Antenna Installation
4. For models MBW 1100F Triple-Radio, MBW 1100F 58, MBW 1100F-
HLS and MBW 1100E Triple-Radio; attach the 5GHz or 4.9GHz third
band antenna to terminal B3. Tighten the antenna by hand at its
metallic base. The antenna should rotate easily. Do not apply
excessive force by using any tool, as this may damage the unit.
- Page 15 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Figure 9: 5 GHz or 4.9GHz Third Band Antenna Installation
5. One or both of the 5GHz antennas can be replaced by a panel
antenna (e.g. MBW-WLS-ANT-KT-5820) for point to point connections
which require better link budget.
Cable Connections
When the MBW 1100 (WLP) is properly aligned, the connecters are located
at the bottom of the unit.
Cable requirements are often unique to the location and deployment
topology of each installation. As a result of this limitation, the Ethernet and
grounding cables are not included in the installation kit.
The following cables are required to install the MBW 1100 (WLP) unit and
should be connected in the following order:
Grounding Cable – Provides the necessary electrical safety
functions.
Ethernet Cable – Required only for MBW 1100 (WLP) units
connected to a wired network.
Power Cable – Supplies AC power to the MBW 1100 (WLP) unit.
RS-232 Console Cable – Provides a connection from the MBW
1100 (WLP) unit to a console (laptop computer) for configuration.
This is only required when the MBW 1100 (WLP) unit is not pre-
configured. This cable is not provided with the MBW 1100 (WLP)
unit. It is recommended that the MBW 1100 (WLP) is pre-configured
prior to installation.
Table 4 lists the MBW 1100 (WLP) Connectors Kit parts:
- Page 16 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Item
No.
Description
Qty
Picture
A
Solderless
Ring Terminal
1
B
Sealed RJ45
connector
1
C
Power
Connector
1
Table 4: Mounting Kit Part List
Cable Installation Tools
The following special tools are required to install and connect cables related
to the MBW 1100 (WLP).
Description
Picture
Slotted Screwdriver
1/8” (3mm) wide
RJ45 Crimp Tool
HT-210A
Table 5: Cable Installation Tools and Equipment
- Page 17 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Grounding Cable
Connect a grounding wire to the grounding screw at the bottom of the
MBW 1100 (WLP) unit. A 10 AWG grounding cable is required to ground
the MBW 1100 (WLP) unit.
Figure 10: Grounding Connection
To ground the MBW 1100 (WLP) unit:
1. Crimp the solderless ring terminal [A] contained in the MBW 1100
(WLP) Connectors Kit to the grounding cable.
2. Attach the solderless ring terminal [A] to the bottom of the MBW
1100 (WLP) unit using the grounding screw.
3. Connect the other end of the grounding cable to a proper ground.
Note: Connect the 10 AWG grounding cable before connecting any other
cables. When removing the MBW 1100 (WLP), the grounding cable
should be the last cable removed.
Noter: Connecter la prise de terre 10 AWG avant de connecter tout autre
câble. Pendant la désinstallation du MBW 1100 (WLP), la prise de
terre doit être le dernier câble retiré.
- Page 18 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Ethernet Connection
Ethernet connection is used for wired backhaul connection or an interface
to a third party wireless BH solution. Use outdoor rated CAT5 shielded
cables or better. The outer diameter of the Ethernet cable should be 4.8 –
7 mm. When using CAT5 shielded cables the cable can be up to 100
meters.
Following is a diagram explaining how the Ethernet cable should be
assembled prior to connecting it to the MBW 1100 (WLP) unit:
Figure 11: Ethernet Cable Connector
Power Connection
The MBW 1100 (WLP) unit can be connected to an AC power source by one
of several methods. It can be connected directly to a power source or by
using an optional adapter to connect to the streetlight photocell (photo-
control). The MBW 1100 (WLP) unit can support input voltage of 100 to
240 VAC (50 to 60 Hz).
Note: Connect the grounding cable before connecting any other cables.
When removing the MBW 1100 (WLP), the grounding cable should
be the last cable removed.
Noter: Connecter la prise de terre 10 AWG avant de connecter tout autre
câble. Pendant la désinstallation du MBW 1100 (WLP), la prise de
terre doit être le dernier câble retiré.
To connect the AC power to the MBW 1100 (WLP) via the streetlight
photocell:
1. Check the input voltage to the streetlight photocell. The voltage
must be between 100 to 240 VAC. If yes, continue with this
procedure. Otherwise, use a different method for the power
connection.
2. Remove the streetlight photocell. Turn the photocell
counterclockwise and lift the photocell out of the socket.
- Page 19 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
3. Insert the Auxiliary Power Adapter in the socket of the photocell.
Note that one prong is larger than the other two. Align the larger
prong on the adapter with the larger slot in the socket. Insert the
Auxiliary Power Adapter into the socket and rotate the adapter
clockwise.
4. Insert the photocell into the Auxiliary Power Adapter. Align the
larger prong on the photocell with the larger slot in the socket on
top of the adapter. Insert the photocell into the socket and rotate
the photocell clockwise.
5. Connect the Auxiliary Power Adapter cable to the power connector
socket on the MBW 1100 (WLP).
6. After connecting the power, verify that the Power (PWR) LED is lit.
7. Check the photocell. Cover the photocell and verify that the
streetlight operates.
Console Connection
Figure 12 illustrates the RS-232 cable connections used to connect the
MBW 1100 (WLP) to a console (notebook computer to configure the MBW
1100 (WLP)). For more information regarding the serial cable, see
Appendix B: Wiring Specifications.
Figure 12: Connect and Access the MBW 1100 (WLP)
Note: New laptops may not include an RS-232 serial port. If a serial port is
not available, you may use a USB to serial converter.
Notebook PC
Consol Port:
Consol Port:
RS232
WLP
RS232
- Page 20 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Power Up and Software Configuration
The MBW 1100 (WLP) unit is normally mounted on a streetlight (pole or
wall) where it is inconvenient to configure. Therefore, it is recommended
that wireless communication be established to the unit prior to installation,
so that the unit can later be configured and monitored from the ground. To
verify communications when installing the MBW 1100 (WLP) unit, the
Mesh-Gateways must be installed and powered up first.
The LEDs on the MBW 1100 (WLP) unit indicate the status of
communications between the MBW 1100 (WLP) unit and the network. See
Table 6 for more information on the LED indicators.
The ACT LED on the Mesh-Gateway should be checked to verify that wired
communications have been established. The BH LED on the Mesh-Gateway
should be checked to verify that wireless communications have been
established.
When powering up a Mesh-Node, the BH LED should be lit to verify that
the MBW 1100 (WLP) unit’s wireless communication is connected. MBW
1100 (WLP) boot time is about 2.5 minutes. The BH LED indicator will light
up after the boot is completed.
LED
Function
PWR
Green – There is power to the unit.
Unlit – There is no power to the unit.
STAT
Green – The operational status of the MBW 1100 (WLP) unit is normal.
Red – The MBW 1100 (WLP) unit is in a failure state.
Unlit – There is no power to the unit.
ACT
Green – When the LED is on, there is a communication connection.
When the LED is flashing, traffic is flowing though the MBW 1100
(WLP) unit.
Unlit – There is no communication connection.
BH
Green – On a Mesh-Gateway, the mesh functionality is activated.
On a Mesh-Node, the MBW 1100 (WLP) is connected to the mesh.
Unlit – On a Mesh-Gateway, the mesh functionality is not activated or
no Ethernet link is available.
On a Mesh-Node, the MBW 1100 (WLP) is not configured or failed to
connect to the mesh.
Table 6: MBW 1100 (WLP) LED Indicators
- Page 21 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Appendix A: List of Acronyms
Acronym
Explanation
802.11
A family of specifications related to wireless networking,
including: 802.11a, 802.11b, and 802.11g.
AP
Access Point. The hub of a wireless network. Wireless
clients connect to the access point, and traffic between
two clients must travel through the access point. Access
points are often abbreviated to AP
BSSID
Broadcast Service Set Identifier
CPE
Customer Premises Equipment.
DHCP
Dynamic Host Configuration Protocol. A protocol which
enables a server to automatically assign an IP address to
clients so that the clients do not have to configure the IP
addresses manually.
EAP
Extensible Authentication Protocol. A standard form of
generic messaging used in 802.1X.
ESSID
EGOed Service Set Identifier
PMK
Pairwise Master Key
SSID
Service Set Identifier, a set of characters that give a
unique name to a WLAN.
TKIP
Temporal Key Integrity Protocol
VLAN
Virtual Local Access Network
WDS
Wireless Distribution System
WEP
Wired Equivalent Privacy. An encryption system created to
prevent eavesdropping on wireless network traffic.
- Page 22 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Acronym
Explanation
WLP
Wireless Base Station. Access point of the GO Networks
MBW solution. (MBW 1100)
WLS
Wireless Base Station access point of the GO Networks
MBW solution. (MBW 2100)
WMG
Wireless Media Gateway of the GO Networks MBW
solution. GO Media dedicated CPE.
WNC
Wireless Network Controller of the GO Networks MBW
solution.
WPA
WiFi Protected Access. A modern encryption system
created to prevent eavesdropping on wireless network
traffic. It is considered more secure than WEP.
WPA-EAP
WPA-Extensible Authentication Protocol
WPA-PSK
WPA-Pre-shared key
- Page 23 of 24 -
All contents are Copyright © 2007 GO Networks, Inc. All rights reserved.
Appendix B: Wiring Specifications
Console
Port (DTE)
RJ-45-to-RJ-45
Straight Cable
RJ-45 to
DB-9
Terminal
Adapter
Console
Device
Signal
RJ-45 Pin
RJ-45 Pin
DB-9 Pin
Signal
No connection
1
1
8
CTS
No connection
2
2
6
DSR
No connection
3
3
5
GND
GND
4
4
5
GND
RxD
5
5
3
TxD
TxD
6
6
2
RxD
No connection
7
7
4
DTR
No connection
8
8
7
RTS
Table 7: Console Port Signaling and Cabling with a
DB-9 Adapter for the MBW 1100 (WLP) Unit