HUIZHOU GAOSHENGDA TECHNOLOGY W7HM1200 WIFI Module User Manual
Hui Zhou Gaoshengda Technology Co.,LTD WIFI Module Users Manual
Contents
- 1. User manual part 1
- 2. User manual part 2
User manual part 1
PRODUCTS USERMANUAL
WIFI Module
IEEE 802.11b/g/n
1T/1R
Model Number: W7HM1200
W7HM1200 is a high-gain and low power consumption wifi mudule . You can use it
on IEEE802.11b/g/n wireless Local Area Networks. It fully complies with IEEE
802.11n and IEEE 802.11b/g feature rich wireless connectivity at high
standards,delivers reliable,cost-effective,throughput from an extended distance.
Complies with IEEE 802.11g; 802.11b; 802.11n standard for 2.4GHz Wireless
LAN.
Supports Ad-Hoc/Infrastructure modes
(This device supports Ad-Hoc mode, however Ad-Hoc is only possible in the
channels 2412-2462MHz and 2422-2452MHz as this is fixed in the firmware of the
module, it can not operate outside the certified channels as indicated in this FCC
certification filing.)
Supports PC Card hot-SWAP and true Plug & Play.
Works with all existing network infrastructure.
Capable of up to 128-Bit WEP Encryption.
Freedom to roam while staying connected.
22-Mbps Packet Binary Convolution Coding (PBCC)
(according to the IEEE Std 802.11b high-rate specification ).
UP to 54 Mbps High-Speed Transfer Rate in 802.11g mode of operation.
Integrated Antenna.
Supports Windows7, XP32/64,Vista32/64,Linux
Low power consumption.
Easy to install and configure.
Product Features
Product Description
PRODUCTS USERMANUAL
FCC Statement
Thi
se
q
u
ip
men
th
as
b
een
t
es
t
e
d
an
df
oun
dt
ocom
ply
w
ith th
e
li
m
it
s
f
or a
Cl
ass
B
digit
a
ld
ev
i
ce,
p
ursuan
tt
o
p
ar
t15
o
fth
e
FCC
ru
l
es.
Th
ese
li
m
it
sare
d
es
ig
ne
dt
o
p
rov
id
e reasona
bl
e
p
ro
t
ec
ti
on a
g
a
i
ns
th
arm
f
u
li
n
t
er
f
erence
i
nares
id
en
ti
a
l
i
ns
t
a
ll
a
ti
on.
Thi
se
q
u
ip
men
tg
enera
t
es, uses an
d
can ra
di
a
t
era
di
o
f
re
q
uenc
y
ener
gy
an
d
,
if
no
ti
ns
t
a
ll
e
d
an
d
use
di
naccor
d
ance w
ith th
e
i
ns
t
ruc
ti
ons, ma
y
cause
h
arm
f
u
l
i
n
t
er
f
erence
t
ora
di
ocommun
i
ca
ti
ons.
H
owever,
th
ere
i
sno
g
uaran
t
ee
th
a
t
i
n
t
er
f
erence w
ill
no
t
occur
i
na
p
ar
ti
cu
l
ar
i
ns
t
a
ll
a
ti
on.
If thi
se
q
u
ip
men
td
oes cause
h
arm
f
u
li
n
t
er
f
erence
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interferencereceived, including interference that may
cause undesired operation.
Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void
FCC Important Notes:
(1)
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body and must
not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
The devices must be installed and used in strict accordance with the manufacturer’s
instructions as described in the user documentation that comes with the product.
Modular could be only used in mobile or fix device, and could not be used in any
portable device.
Caution!
PRODUCTS USERMANUAL
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user
authority to operate the equipment.
(2)
Co-location Warning:
This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
(3)
Limited Channels fixed for use in the US:
IEEE 802.11b or 802.11g or 802.11n(HT20) operation of this product in the U.S. is
firmware-limited to Channel 1 through 11.
IEEE 802.11n(HT40) operation of this product in the U.S. is firmware-limited to
Channel 3 through 9.
(4)
OEM integration instructions:
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna
and users, and thetransmitter module may not be co-located with any other
transmitter or antenna. The module shall be only used with the intergral antenna(s)
that has been originally tested and certified with this module.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirementsrequired with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
(5)
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization
for this module in combination with the host equipment is no longer considered valid
and the FCC ID of the module cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.
(6)
End product labeling:
This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users.
The final end product must be labeled in a visible area with the following:
(7)
Information that must be placed in the end user manual:
PRODUCTS USERMANUAL
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user's manual of the end
product which integrates this module. The end user manual shall include all required
regulatory information/warning as show in this manual.
If the FCC identification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label referring
to the enclosed module. This exterior label can use wording such as the following: “Contains
Transmitter Module FCC ID: 2AC23W7HM1200 Or Contains FCC ID: 2AC23W7HM1200ā
when the module is installed inside another device, the user manual of this device must contain
below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as
described in the user documentation that comes with the product
IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui
peuvent causer un mauvais fonctionnement de l'appareil.
IC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular
cannot be installed in any portable device, for example, USB dongle like transmitters is
forbidden.
This modular complies with IC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter. This modular must be installed and operated with a
minimum distance of 20 cm between the radiator and user body. Cette modulaire doit
être installé et utilisé à une distance minimum de 20 cm entre le radiateur et le corps de
l'utilisateur.
If the IC number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label
referring to the enclosed module. This exterior label can use wording such as the
following:
“Contains IC: 12290A-W7HM1200
when the module is installed inside another device, the user manual of this device must
contain below warning statements;
1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui
peuvent causer un mauvais fonctionnement de l'appareil.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product