Hp 7000 Dl Router Series Command Reference Guide SROS Line Interface

2015-01-05

: Hp Hp-7000-Dl-Router-Series-Command-Reference-Guide-155462 hp-7000-dl-router-series-command-reference-guide-155462 hp pdf

Open the PDF directly: View PDF PDF.
Page Count: 941

DownloadHp Hp-7000-Dl-Router-Series-Command-Reference-Guide- SROS Command Line Interface Reference Guide  Hp-7000-dl-router-series-command-reference-guide
Open PDF In BrowserView PDF
SROS Command Line Interface
Reference Guide
Software Version J.02.01 or Greater

April 2005
61195880L1-35B

© Copyright 2005 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without
notice.
This document contains proprietary information, which is protected by
copyright. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of
Hewlett-Packard.

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF
ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with
the furnishing, performance, or use of this material.
The only warranties for HP products and services are set forth in the
express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.

Publication Number
5991-2114
January 2005

Applicable Products
ProCurve Secure Router 7102dl
ProCurve Secure Router 7203dl

Disclaimer

Hewlett-Packard assumes no responsibility for the use or reliability of
its software on equipment that is not furnished by Hewlett-Packard.
(J8752A)
(J8753A)

Warranty
See the Customer Support/Warranty booklet included with the product.
A copy of the specific warranty terms applicable to your HewlettPackard products and replacement parts can be obtained from your HP
Sales and Service Office or authorized dealer.

Microsoft and Windows are U.S. registered trademarks of Microsoft
Corporation. CompactFlash is a U.S. registered trademark of the
CompactFlash Association. AOL Instant Messenger (AIM) is a U.S.
registered trademark of American Online, Inc. Quake is a U.S.
registered trademark of id Software, Inc. ICQ is a U.S. registered
trademark of ICQ, Inc. pcAnywhere is a U.S. trademark of Synamtec
Corporation.

SROS Command Line Interface Reference Guide

Table of Contents
Basic Mode Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Enable Mode Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Global Configuration Mode Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
DHCP Pool Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
IKE Policy Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
IKE Policy Attributes Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
IKE Client Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Crypto Map IKE Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Crypto Map Manual Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
Radius Group Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
CA Profile Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
Certificate Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
Ethernet Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
DDS Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
Serial Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494
T1 Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
DSX-1 Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
E1 Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
G.703 Interface Configuration Command set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
Modem Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
BRI Interface Configuration Command set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556
Frame Relay Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
Frame Relay Sub-Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
ATM Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644
ATM Sub-Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647
ADSL Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
BGP Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705
BGP Neighbor Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
PPP Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715
Tunnel Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 778
HDLC Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 811
Loopback Interface Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 847
Line (Console) Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876
Line (Telnet) Interface Config Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887
Router (RIP) Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 894
Router (OSPF) Configuration Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903
Quality of Service (QoS) Map Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
Common Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 922
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 936

5991-2114

© Copyright 2005 Hewlett-Packard Development Company, L.P.

3

Command Reference Guide

CLI Introduction

REFERENCE GUIDE INTRODUCTION
This manual provides information about the commands that are available with all of the ProCurve Secure
routers.
If you are new to the Operating System’s Command Line Interface (CLI), take a few moments to review
the information provided in the section which follows (CLI Introduction).
If you are already familiar with the CLI and you need information on a specific command or group of
commands, proceed to Command Descriptions on page 9 of this guide.

CLI INTRODUCTION
This portion of the Command Reference Guide is designed to introduce you to the basic concepts and
strategies associated with using the Operating System’s Command Line Interface (CLI).

Accessing the CLI from your PC
All products using the are initially accessed by connecting a VT100 terminal (or terminal emulator) to the
CONSOLE port located on the rear panel of the unit using a standard DB-9 (male) to DB-9 (female) serial
cable. Configure the VT100 terminal or terminal emulation software to the following settings:
•
•
•
•
•

9600 baud
8 data bits
No parity
1 stop bit
No flow control

Note

For more details on connecting to your unit, refer to the Quick Configuration Guides and
Quick Start Guides located on the Secure Router OS Documentation CD provided with
your unit.

Understanding Command Security Levels
The has two command security levels — Basic and Enable. Both levels support a specific set of
commands. For example, all interface configuration commands are accessible only through the Enable
security level. The following table contains a brief description of each level.
Level

Access by...

Prompt

Basic

beginning an SROS session. >

With this level you can...
•
•
•

5991-2114

display system information
perform traceroute and ping
functions
open a Telnet session

© Copyright 2005 Hewlett-Packard Development Company, L.P.

4

Command Reference Guide

Understanding Configuration Modes

Level

Access by...

Prompt

Enable

entering enable while in the #
Basic command security level
as follows:

•
•
•

>enable

Note

With this level you can...
manage the startup and running
configurations
use the debug commands
enter any of the configuration modes

To prevent unauthorized users from accessing the configuration functions of your product,
immediately install an Enable-level password. Refer to the Quick Configuration Guides
and Quick Start Guides located on the Secure Router OS Documentation CD provided
with your unit for more information on configuring a password.

Understanding Configuration Modes
The Secure Router OS has four configuration modes to organize the configuration commands – Global,
Line, Router, and Interface. Each configuration mode supports a set of commands specific to the
configurable parameters for the mode. For example, all Frame Relay configuration commands are
accessible only through the Interface Configuration Mode (for the virtual Frame Relay interface). The
following table contains a brief description of each level.
Mode

Access by...

Sample Prompt

With this mode you
can...

Global

entering config while at the Enable
command security level prompt.
For example:

(config)#

•

>enable
#config term

•

•
•

Line

specifying a line (console or Telnet)
(config-con0)#
while at the Global Configuration Mode
prompt.
For example:

>enable
#config term
(config)#line console 0

5991-2114

© Copyright 2005 Hewlett-Packard Development Company, L.P.

•

•

set the system’s
Enable-level
password(s)
configure the
system global IP
parameters
configure the SNMP
parameters
enter any of the
other configuration
modes
configure the
console terminal
settings (datarate,
login password,
etc.)
create Telnet logins
and specify their
parameters (login
password, etc.)

5

Command Reference Guide

Using CLI Shortcuts

Mode

Access by...

Sample Prompt

With this mode you
can...

Router

entering router rip router or
router ospf while at the Global
Configuration Mode prompt.
For example:

(config-rip)#

•
•
•

>enable
#config term
(config)#router rip
Interface

specifying an interface (T1, Ethernet,
Frame Relay, ppp, etc.) while in the
Global Configuration Mode.
For example:

>enable
#config term
(config)#int eth 0/1

(config-eth 0/1)#

•

(The above prompt is for the
Ethernet LAN interface located
on the rear panel of the unit.)

configure RIP or
OSPF parameters
suppress route
updates
redistribute
information from
outside routing
sources (protocols)
configure
parameters for the
available LAN and
WAN interfaces

Using CLI Shortcuts
The provides several shortcuts which help you configure your Secure Router OS product more easily. See
the following table for descriptions.
Shortcut

Description

Up arrow key

To re-display a previously entered command, use the up arrow key. Continuing to press
the up arrow key cycles through all commands entered starting with the most recent
command.

Tab key

Pressing the  key after entering a partial (but unique) command will complete the
command, display it on the command prompt line, and wait for further input.

?

The CLI contains help to guide you through the configuration process. Using the question
mark, do any of the following:
• Display a list of all subcommands in the current mode. For example:

(config-t1 1/1)#coding ?
ami - Alternate Mark Inversion
b8zs - Bipolar Eight Zero Substitution
•

Display a list of available commands beginning with certain letter(s). For example:

(config)#ip d?
default-gateway
domain-proxy
•

dhcp-server

domain-lookup

domain-name

Obtain syntax help for a specific command by entering the command, a space, and
then a question mark (?). The CLI displays the range of values and a brief
description of the next parameter expected for that particular command. For
example:

(config-eth 0/1)#mtu ?
<64-1500> - MTU (bytes)

5991-2114

© Copyright 2005 Hewlett-Packard Development Company, L.P.

6

Command Reference Guide

Performing Common CLI Functions

Shortcut

Description

 + A

Jump to the beginning of the displayed command line. This shortcut is helpful when using
the no form of commands (when available). For example, pressing  at the
following prompt will place the cursor directly after the #:

(config-eth 0/1)#ip address 192.33.55.6
 + E

Jump to the end of the displayed command line. For example, pressing  at the
following prompt will place the cursor directly after the 6:

(config-eth 0/1)#ip address 192.33.55.6
 + U

Clears the current displayed command line. The following provides an example of the  feature:
(config-eth 0/1)#ip address 192.33.55.6 (Press  here)

(config-eth 0/1)#
auto finish

You need only enter enough letters to identify a command as unique. For example,
entering int t1 1/1 at the Global configuration prompt provides you access to the
configuration parameters for the specified T1 interface. Entering interface t1 1/1
would work as well, but is not necessary.

Performing Common CLI Functions
The following table contains descriptions of common CLI commands.
Command

Description

do

The do command provides a way to execute commands in
other command sets without taking the time to exit the
current and enter the desired one. The following example
shows the do command used to view the Frame Relay
interface configuration while currently in the T1 interface
command set:

(config)#interface t1 1/1
(config-t1 1/1)#do show interfaces fr 7
no

To undo an issued command or to disable a feature, enter
no before the command.
For example:

no shutdown t1 1/1
copy running-config startup-config When you are ready to save the changes made to the

configuration, enter this command. This copies your
changes to the unit’s nonvolatile random access memory
(NVRAM). Once the save is complete, the changes are
retained even if the unit is shut down or suffers a power
outage.

show running config

5991-2114

Displays the current configuration.

© Copyright 2005 Hewlett-Packard Development Company, L.P.

7

Command Reference Guide

Understanding CLI Error Messages

Command

Description

debug

Use the debug command to troubleshoot problems you
may be experiencing on your network. These commands
provide additional information to help you better interpret
possible problems. For information on specific debug
commands, refer to the section Enable Mode Command
Set on page 20.

undebug all

To turn off any active debug commands, enter this
command.

Caution

The overhead associated with the debug command takes up a large portion of your
product’s resources and at times can halt other processes. It is best to only use the debug
command during times when the network resources are in low demand (non-peak hours,
weekends, etc.).

Understanding CLI Error Messages
The following table lists and defines some of the more common error messages given in the CLI.
Message

Helpful Hints

%Ambiguous command
%Unrecognized Command

The command may not be valid in the current command mode, or you may
not have entered enough correct characters for the command to be
recognized. Try using the “?” command to determine your error. See Using
CLI Shortcuts on page 6 for more information.

%Invalid or incomplete The command may not be valid in the current command mode, or you may
not have entered all of the pertinent information required to make the
command
command valid. Try using the “?” command to determine your error. See
Using CLI Shortcuts on page 6 for more information.

The error in command entry is located where the caret (^) mark appears.
%Invalid input
detected at “^" marker Enter a question mark at the prompt. The system will display a list of
applicable commands or will give syntax information for the entry.

5991-2114

© Copyright 2005 Hewlett-Packard Development Company, L.P.

8

Command Reference Guide

Command Descriptions

COMMAND DESCRIPTIONS
This portion of the guide provides a detailed listing of all available commands for the CLI (organized by
command set). Each command listing contains pertinent information including the default value, a
description of all sub-command parameters, functional notes for using the command, and a brief
technology review. To search for a particular command alphabetically, use the Index. To search for
information on a group of commands within a particular command set, use the linked references given
below:
Basic Mode Command Set on page 10
Enable Mode Command Set on page 20
Global Configuration Mode Command Set on page 200
DHCP Pool Command Set on page 355
IKE Policy Command Set on page 373
IKE Policy Attributes Command Set on page 386
IKE Client Command Set on page 392
Crypto Map IKE Command Set on page 396
Crypto Map Manual Command Set on page 405
Radius Group Command Set on page 416
CA Profile Configuration Command Set on page 418
Certificate Configuration Command Set on page 429
Ethernet Interface Configuration Command Set on page 433
DDS Interface Configuration Command Set on page 486
Serial Interface Configuration Command Set on page 494
T1 Interface Configuration Command Set on page 504
DSX-1 Interface Configuration Command Set on page 520
E1 Interface Configuration Command Set on page 530
G.703 Interface Configuration Command set on page 545
Modem Interface Configuration Command Set on page 552
BRI Interface Configuration Command set on page 556
Frame Relay Interface Config Command Set on page 567
Frame Relay Sub-Interface Config Command Set on page 587
ATM Interface Config Command Set on page 644
ATM Sub-Interface Config Command Set on page 647
ADSL Interface Config Command Set on page 701
BGP Configuration Command Set on page 705
BGP Neighbor Configuration Command Set on page 711
PPP Interface Configuration Command Set on page 715
Tunnel Configuration Command Set on page 778
HDLC Command Set on page 811
Loopback Interface Configuration Command Set on page 847
Line (Console) Interface Config Command Set on page 876
Line (Telnet) Interface Config Command Set on page 887
Router (RIP) Configuration Command Set on page 894
Router (OSPF) Configuration Command Set on page 903
Common Commands on page 922
5991-2114

© Copyright 2005 Hewlett-Packard Development Company, L.P.

9

SROS Command Line Interface Reference Guide

Basic Mode Command Set

BASIC MODE COMMAND SET
To activate the Basic Mode, simply log in to the unit. After connecting the unit to a VT100 terminal (or
terminal emulator) and activating a terminal session, the following prompt displays:
Router>
The following command is common to multiple command sets and is covered in a centralized section of
this guide. For more information, refer to the section listed below:
exit on page 930
All other commands for this command set are described in this section in alphabetical order.
enable on page 11
logout on page 12
ping 
on page 13 show clock on page 15 show snmp on page 16 show version on page 17 telnet
on page 18 traceroute
on page 19 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 10 SROS Command Line Interface Reference Guide Basic Mode Command Set enable Use the enable command (at the Basic Command Mode prompt) to enter the Enable Command Mode. Use the disable command to exit the Enable Command Mode. See the section enable on page 11 for more information. Syntax Description No subcommands. Default Values No default value necessary for this command. Command Modes > Basic Command Mode Functional Notes The Enable Command Mode provides access to operating and configuration parameters and should be password protected to prevent unauthorized use. Use the enable password command (found in the Global Configuration) to specify an Enable Command Mode password. If the password is set, access to the Enable Commands (and all other “privileged” commands) is only granted when the correct password is entered. Usage Examples The following example enters the Enable Command Mode and defines an Enable Command Mode password: >enable #configure terminal (config)#enable password password At the next login, the following sequence must occur: >enable Password: ****** # 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 11 SROS Command Line Interface Reference Guide Basic Mode Command Set logout Use the logout command to terminate the current session and return to the login screen. Syntax Description No subcommands. Default Values No defaults necessary for this command. Command Modes > or # Basic or Enable Command Mode Usage Examples The following example shows the logout command being executed in the Basic Mode: >logout Session now available Press RETURN to get started. 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 12 SROS Command Line Interface Reference Guide Basic Mode Command Set ping
Use the ping command (at the Basic Command Mode prompt) to verify IP network connectivity. Syntax Description
Optional. Specifies the IP address of the system to ping. Entering the ping command with no specified address prompts the user with parameters for a more detailed ping configuration. See Functional Notes (below) for more information. Default Values No default value necessary for this command. Command Modes > or # Basic or Enable Command Mode Functional Notes The ping command helps diagnose basic IP network connectivity using the Packet InterNet Groper program to repeatedly bounce Internet Control Message Protocol (ICMP) Echo_Request packets off a system (using a specified IP address). The Secure Router OS allows executing a standard ping request to a specified IP address or provides a set of prompts to configure a more specific ping configuration. The following is a list of output messages from the ping command: ! Success Destination Host Unreachable $ Invalid Host Address X TTL Expired in Transit ? Unknown Host * Request Timed Out The following is a list of available extended ping fields with descriptions: Target IP address: Specifies the IP address of the system to ping. Repeat Count: Number of ping packets to send to the system (valid range: 1 to 1000000). Datagram Size: 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 13 SROS Command Line Interface Reference Guide Basic Mode Command Set Size (in bytes) of the ping packet (valid range: 1 to 1448). Timeout in Seconds: If a ping response is not received within the timeout period, the ping is considered unsuccessful (valid range: 1 to 5 seconds). Extended Commands: Specifies whether additional commands are desired for more ping configuration parameters. Source Address (or interface): Specifies the IP address to use as the source address in the ECHO_REQ packets. Data Pattern: Specify an alphanumerical string to use (the ASCII equivalent) as the data pattern in the ECHO_REQ packets. Sweep Range of Sizes: Varies the sizes of the ECHO_REQ packets transmitted. Sweep Min Size: Specifies the minimum size of the ECHO_REQ packet (valid range: 0 to 1448). Sweep Max Size: Specifies the maximum size of the ECHO_REQ packet (valid range: Sweep Min Size to 1448). Sweep Interval: Specifies the interval used to determine packet size when performing the sweep (valid range: 1 to 1448). Verbose Output: Specifies an extended results output. Usage Examples The following is an example of a successful ping command: >ping Target IP address:192.168.0.30 Repeat count[1-1000000]:5 Datagram Size [1-1000000]:100 Timeout in seconds [1-5]:2 Extended Commands? [y or n]:n Type CTRL+C to abort. Legend: '!' = Success '?' = Unknown host '$' = Invalid host address '*' = Request timed out '-' = Destination host unreachable 'x' = TTL expired in transit Pinging 192.168.0.30 with 100 bytes of data: !!!!! Success rate is 100 percent (5/5) round-trip min/avg/max = 19/20.8/25 ms 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 14 SROS Command Line Interface Reference Guide Basic Mode Command Set show clock Use the show clock command to display the system time and date entered using the clock set command. Syntax Description No subcommands. Default Values No default value necessary for this command. Command Modes > or # Basic or Enable Command Mode Usage Examples The following example displays the current time and data from the system clock: >show clock 23:35:07 UTC Tue Aug 20 2002 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 15 SROS Command Line Interface Reference Guide Basic Mode Command Set show snmp Use the show snmp command to display the system Simple Network Management Protocol (SNMP) parameters and current status of SNMP communications. Syntax Description No subcommands. Default Values No default value necessary for this command. Command Modes > or # Basic or Enable Command Mode Usage Examples The following is an example output using the show snmp command for a system with SNMP disabled and the default Chassis and Contact parameters: >show snmp Chassis: Chassis ID Contact: Customer Service 0 Rx SNMP packets 0 Bad community names 0 Bad community uses 0 Bad versions 0 Silent drops 0 Proxy drops 0 ASN parse errors 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 16 SROS Command Line Interface Reference Guide Basic Mode Command Set show version Use the show version command to display the current Secure Router OS version information. Syntax Description No subcommands. Default Values No default value necessary for this command. Command Modes > or # Basic or Enable Command Mode Usage Examples The following is a sample show version output: >show version ProCurve Secure Router 7203dl SROS Version: J02.01.01 Checksum: 5509EBDC, built on: Mon Mar 21 14:48:04 2005 Boot ROM version J02.01.01 Checksum: 9C0F, built on: Mon Mar 21 14:48:24 2005 Copyright (c) 2005-2005, Hewlett-Packard, Co. Platform: ProCurve Secure Router 7203dl Serial number US449TS029 Flash: 33554432 bytes DRAM: 268435455 bytes System uptime is 0 days, 21 hours, 27 minutes, 0 seconds Current system image file is "CFLASH:/J02_01_01.biz" Boot system image file is "CFLASH:/J02_01_01.biz" Primary system configuration file is "startup-config" System booted up using configuration file: "startup-config" 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 17 SROS Command Line Interface Reference Guide Basic Mode Command Set telnet
Use the telnet command to open a Telnet session (through the Secure Router OS) to another system on the network. Syntax Description
Specifies the IP address of the remote system. Default Values No default value necessary for this command. Command Modes > or # Basic or Enable Command Mode Usage Examples The following example opens a Telnet session with a remote system (10.200.4.15): >telnet 10.200.4.15 User Access Login Password: 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 18 SROS Command Line Interface Reference Guide Basic Mode Command Set traceroute
Use the traceroute command to display the IP routes a packet takes to reach the specified destination. Syntax Description
Specifies the IP address of the remote system to trace the routes to Default Values No default value necessary for this command. Command Modes > or # Basic or Enable Command Mode Usage Examples The following example performs a traceroute on the IP address 192.168.0.1: #traceroute 192.168.0.1 Type CTRL+C to abort. Tracing route to 192.168.0.1 over a maximum of 30 hops 1 22ms 20ms 20ms 192.168.0.65 2 23ms 20ms 20ms 192.168.0.1 # 5991-2114 © Copyright 2005 Hewlett-Packard Development Company, L.P. 19 SROS Command Line Interface Reference Guide Enable Mode Command Set ENABLE MODE COMMAND SET To activate the Enable Mode, enter the enable command at the Basic Mode prompt. (If an enable password has been configured, a password prompt will display.) For example: Router>enable Password: XXXXXXX Router# The following commands are common to multiple command sets and are covered in a centralized section of this guide. For more information, refer to the section listed below: bind <#> on page 924 description on page 927 exit on page 930 ping
on page 931 show running-config on page 933 All other commands for this command set are described in this section in alphabetical order. clear commands begin on page 22 clock auto-correct-dst on page 48 clock set

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 941
Page Mode                       : UseOutlines
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:42c7b9f9-43a8-4b33-ac91-324557290803
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2005:03:25 06:53:17-08:00
Create Date                     : 2005:03:22 14:17:00Z
Metadata Date                   : 2005:03:25 06:53:17-08:00
Document ID                     : uuid:89b58746-b6a8-4de0-bedd-91506138737e
Format                          : application/pdf
Title                           : SROS Command Line Interface Reference Guide
Creator                         : ProCurve Networking by HP
Description                     : ProCurve Secure Router 7000dl Series
Author                          : ProCurve Networking by HP
Subject                         : ProCurve Secure Router 7000dl Series
EXIF Metadata provided by EXIF.tools

Navigation menu