Huawei Technologies E5838 Wireless Modem User Manual English

Download:
Mirror Download [FCC.gov]
Document ID	1143111
Application ID	DP4VNHptwgr+J95IZyi6mQ==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.83kB (97880 bits)
Date Submitted	2009-07-22 00:00:00
Date Available	2009-10-20 00:00:00
Creation Date	2009-07-13 17:30:31
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2009-07-13 17:34:00
Document Title	English
Document Creator	Acrobat PDFMaker 7.0 for Word
Document Author:	z45031

Thank you for choosing this Wireless Modem.
Note:
This manual briefly describes the appearance, the preparation and the
process for installing/uninstalling.
Getting to Know your Wireless Modem
The following figures show the appearance of the Wireless Modem. The
actual product may differ.
Micro SD card slot
Hold the Micro SD card.
USB connector
Connect to the USB interface of the PC or the charger.
Power switch
Press and hold it to power on or off the Wireless Modem.
WiFi/WPS switch
Press it to enable or disable the WiFi (Wireless Fidelity).
Press and hold it to enable or disable the WPS (Wi-Fi Protected Setup).
Dial key
Press and hold it to set up a connection by dialing up or tear down a
connection.
Battery_button
Press and hold it to open the battery cover.
WiFi indicator
Off: The WiFi and WPS are disabled.
Blinking: The WPS is enabled.
Steady on: The WiFi is enabled.
Roam indicator
Off: The Wireless Modem is not in the roaming state.
Blinking in red: The Wireless Modem is in the roaming state.
Signal indicator
Off: The signal is inexistent.
Fast blinking in red: The USIM/SIM card does not exist or the PIN code
is not verified.
Steady on and in red: The signal strength is weak.
Steady on and in yellow: The signal strength is medium.
Steady on and in green: The signal strength is strong.
Mode indicator
Double blinking in green: The network is inexistent.
Blinking in green: Registering with the 2G network.
Steady on and in green: 2G data service connected.
Blinking in blue: Registering with the 3G network.
Steady on and in blue: WCDMA data service connected.
Steady on and in cyan: HSPA (HSDPA/HSUPA) data service connected.
Battery indicator
Blinking: The battery is being charged.
Fast blinking in red: The battery power level is very low and need to be
charged.
Steady on and in red: The battery power level is weak.
Steady on and in yellow: The battery power level is normal.
Steady on and in green: The battery power level is enough.
Note:
z Press the Dial key and Power switch at the same time. The device
changes to the forcible downloading state.
z Press and hold WiFi/WPS switch and Power switch at the same time to
restore the factory defaults.
z If the device has not been accessed for 10 minutes, the WiFi is
automatically disabled and the device changes to the deep sleep state.
When the device is in the deep sleep state, press any key to activate the
WiFi and the device. Then, the indicators become lightened. In 10s, the
indicators go out.
Preparing the Wireless Modem
USIM/SIM Card and Battery
Note:
z Keep the USIM/SIM card out of the reach of children.
z The USIM/SIM card and its metal contacts can be easily damaged by
scratching or bending. Ensure care when you carry, load or remove it.
z Do not remove the USIM/SIM card and the Micro SD card when they are
being used. Removing the cards during an operation may damage the
cards as well as the device, and data stored on the cards may be
corrupted.
Micro SD card
1.
Remove the rubber cap from the Micro SD card slot; then insert the
Micro SD card into the slot.
2.
After inserting the Micro SD card completely, replace the rubber cap.
Note:
z Micro SD card is an optional accessory. If the Micro SD card is not
provided in the package, you can buy one yourself.
z To remove the Micro SD card, open the rubber cap and press the Micro
SD card gently. Now the Micro SD card will pop up automatically. Then
take it out.
Charging the Battery
Method 1: Using the charger
1.
Insert the plug of the charger into the USB connector of the Wireless
Modem.
2.
Insert the other plug of the charger into a power socket.
Note:
Charger is an optional accessory. If the charger is not provided in the
package, you can contact your device dealer to buy a compatible charger
yourself.
Method 2: Connecting to a PC for charging
Connect the Wireless Modem and PC with the compatible data cable.
Note:
z When you charge the battery for the first time, please charge it for a
minimum of 12 hours.
z The battery discharges even while not being used. If you have not used
it for a long time, please recharge it first.
z The charging time depends on the environmental temperature and the
age of the battery.
z
Do not strike, throw or cause any kind of violent shock to the battery,
otherwise liquid leakage, body damage, overheating, fire or explosion
may occur.
The battery can be recharged but eventually wears out.
If the battery lasts for a shorter time period than usual after being
charged normally, replace it with a battery of the same type.
Installation Guide
The procedure for installing the management program depends on the
operating system installed on your PC. The following section takes
Windows XP as an example.
Installing the Management Program
Connect the Wireless Modem to the PC.
The OS (Operating System) automatically detects and recognizes
new hardware and starts the installation wizard.
Note:
If the auto-run program does not respond, find the AutoRun.exe file in the
driver path. Then double-click AutoRun.exe to run the program.
1.
2.
3.
4.
Follow the prompts of the installation wizard.
After the program is installed, the shortcut icon of the management
program is displayed on the desktop.
Starting the Management Program
After the Wireless Modem is installed, the management program is
launched automatically. Then every time the Wireless Modem is connected
to the PC, the management program is launched automatically.
You can also double-click the shortcut icon on the desktop to launch the
management program.
Uninstalling the Management Program
1.
2.
Choose Start > Control Panel.
Find the management program, and click Add/Remove program
to uninstall the management program.
Note:
It is recommended to restart the PC after the un-installation to ensure that
the management program is completely uninstalled.
Removing the Wireless Modem
1.
Double-click
in the system tray. The Unplug or Eject
Hardware interface is displayed.
2.
Select the hardware related to the Wireless Modem and click Stop.
3.
When the prompt "It is safe to remove the device" is displayed,
remove the Wireless Modem.
Note:
Before removing the Wireless Modem, exit the management program.
Application scenario
Router Mode
In this mode, you can use the wireless Internet service through setting up
the WiFi connection when the Wireless Modem is powered by the built-in
battery but not connected to a PC with the USB cable.
Modem Mode
In this mode, you can use the modem-based Internet service by
connecting the Wireless Modem to the PC with the USB cable. If the WiFi is
enabled, you can use the Internet service of the Router mode.
Setting up the WiFi Connection
1.
Select Start > Control Panel > Network Connections >
Wireless Network Connection.
2.
Find out the wireless network connection whose name is the same as
the network name of the Wireless Modem and double-click the
connection.
3.
Enter the correct security key.
4.
Click Connect.
Note:
z You can find the network name and security key used for WiFi
authentication on the base of your Wireless Modem or contact your
network service provider.
z A maximum of five wireless users can access the Wireless Modem at the
same time. You can set up the WLAN with the access point (AP) function.
Version: V100R001_01
Part Number: 31010AMM

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Sflag                           : 1243304186
Slevelui                        : 0
Slevel                          : 5
Company                         : Huawei Technologies Co., Ltd.
Source Modified                 : D:20090526032928
Modify Date                     : 2009:07:13 17:34+08:00
Create Date                     : 2009:07:13 17:30:31+08:00
Creator Tool                    : Acrobat PDFMaker 7.0 for Word
Metadata Date                   : 2009:07:13 17:34+08:00
Document ID                     : uuid:867a7122-d7a2-42a5-b880-ac69f326ac36
Instance ID                     : uuid:ff3efec3-b688-42f5-aeeb-45f8133ec677
Version ID                      : 98
Format                          : application/pdf
Title                           : English
Creator                         : z45031
Subject                         : 
Headline                        : 
Page Count                      : 4
Page Layout                     : OneColumn
Author                          : z45031

EXIF Metadata provided by EXIF.tools