IER 400-UHF04 Printer with RFID User Manual

IER Printer with RFID N0C4SEA2

a href="https://usermanual.wiki/IER" itemprop="url"> IER >

User Manual

IER 400 N0C4SEA2 USER SAFETY GUIDE WARNING THIS PRODUCT COMES WITH A LITHIUM BATTERY. BATTERY REPLACEMENT MUST IMPERATIVELY BE PERFORMED BY QUALIFIED MAINTENANCE PERSONNEL. MOREOVER, ONLY IER APPROVED MODELS MAY BE USED. DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. DO NOT OPEN THE POWER SUPPLY UNIT CASE FOR ANY REASON, SINCE HIGH VOLTAGE MAY BE PRESENT. DO NOT REPLACE THE FUSE OF THE POWER SUPPLY UNIT. The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following notice be brought to the attention of users of this product. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. In accordance with FCC requirements, changes or modifications not expressly approved by IER could void the user's authority to operate this product. Use of a shielded cable is required to comply within Class B limits of Part 15 of FCC Rules. NORWAY: This product is also designed for IT power distribution system with phase-to-phase voltage 230V. NORWAY & SWEDEN: Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk. THIS APPLIANCE MUST BE GROUNDED. THIS PRODUCT MUST EXCLUSIVELY BE CONNECTED TO AN ELECTRICAL CIRCUIT THAT IS - PROVIDED WITH A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) COMPLYING WITH IEC 364 AND NFC15-100 REGULATIONS, AND - CONFORMING WITH THE VOLTAGE CHARACTERISTICS SPECIFIED BY THE NF EN 50160 STANDARD. The cover(s), and/or door(s) of this product is (are) intended for occasional use and must be normally closed. In compliance with the European Directive 2002/96/CE relative to the management of Waste Electrical and Electronic Equipment (WEEE) implemented as of August 13, 2005, this product may not be disposed of with regular household waste. All products concerned by this directive are marked with the above symbol. The end owner of this product is responsible for either: • Transferring the product to an authorized treatment facility where the product components, recognized to present a hazard to the environment and/or public health, will be recycled and recovered properly, or • Consulting with the manufacturer for appropriate product waste management according to the terms of the manufacturer. The information and specifications contained in this document are subject to change without prior notice. ENGLISH
OPERATING CONDITIONS AND ELECTRICAL CHARACTERISTICS Environmental Conditions Operating Temperature......................................................................................... +5°C (41°F) to 40°C (104°F) Storage Temperature............................................................................................-20°C (-4°F) to 60°C (140°F) Relative Humidity ........................................................................................20% to 80%, without condensation Operating Environment ....................................................................................................... Fully enclosed area (airport lobby, railway station, travel agency, etc.) Power Requirements Line Voltage ............................................................................................................. Authorized voltage ranges 100-120 Vac / 60 Hz / 1.6 A 200-240 Vac / 50 Hz / 0.8 A CONNECTION TO THE LINE VOLTAGE / POWER UP Connecting to the Line Voltage Connect the AC power cord first to the AC power connector on the IER product (see illustration opposite) and then to the AC power outlet. Powering Up Set the power switch to the I position (see illustration opposite). POWERING DOWN / MAKING THE IER PRODUCT ELECTRICALLY SAFE Powering Down Set the power switch to the 0 position (see illustration opposite). Making the IER Product Electrically Safe Disconnect the AC power cord from the AC power connector of the IER product. IMPORTANT: Visit our website to read and/or download the Installation and User Documentation corresponding to your IER product: www.ier.fr
Download:
Mirror Download [FCC.gov]
Document ID1197263
Application ID8tfWEfeWN6HM5VR+7Q4FRw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize13.11kB (163866 bits)
Date Submitted2009-11-10 00:00:00
Date Available2009-11-10 00:00:00
Creation Date2009-01-12 10:06:29
Producing SoftwareAcrobat Distiller 6.0.1 (Windows)
Document Lastmod2009-01-12 10:06:36
Document TitleMicrosoft Word - N0C4SEA2.doc
Document CreatorAcrobat PDFMaker 6.0 pour Word
FCC ID Filing: WGO400-UHF04

Navigation menu