INS Global S1-P 125K proximity card reader User Manual INSG IG B1 R01
INS Global Pty Ltd 125K proximity card reader INSG IG B1 R01
Users Manual
Regulatory Information
CE Mark
The reader has passed all relevant tests and obtained CE approval.
C Tick
The reader has passed all relevant requirements for application of C Tick.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
Any changes or modifications to this product not expressly approved in this document could void the user's authority to operate this equipment.
Designed & Manufactured in Australia. Mifare ®is a registered trademark of Philips Electronics.
Reader Specifications
Reader Output Wiegand
Power requirements +12Vdc
Current Consumption (+/- 5%)
Normal
Activated
Read range
Operating temperature
Relative humidity 90% max, operating non-condensing
Reader dimensions (Facia) 67 x 50 x 16mm
Status LED’s Green/Red controlled by access controller
Audible tone
Colour Charcoal
IP rating
Cable distances
0.22mm2 cable
0.33mm2 cable
100m max
250m max
30 - 50mm
Wiring
Connect the wiring as indicated in the table
to the control panel.
Connect the 0V reference and 0V (if
provided in the power supply) to the ground
(GND) Wire.
Connect the W0, W1, LED and Buzzer
Connect the +Vdc last.
Handling
Handle the reader with care. Do not drop or
damage before installation.
Mounting
If necessary, drill holes for the mounting screws in the wall on which
the reader will be placed.
Alternately a back box can be used.
Note magnet location for position of tamper reed switch (refer overleaf).
Place the reader on the wall or back box, make sure wires are not crushed.
Insert and hand tighten the screws.
Check that the reader is level before tightening screws.
Power up reader
Troubleshooting
If the reader doesn’t respond when a valid smart card is presented,
check the following:
Symptom Possible Cause Check
LED is not lit
LED is orange/indeterminate
or buzzer sounds low
Reader doesn’t respond
No power to the reader
Voltage to the reader is below
minimum required level
Invalid card or card is faulty or
wiring to the controller is faulty
Check power supply to the reader
Check power supply to the reader
Check reader with another valid smart
card; if problem persists check wiring
External Use
Mount the reader on a single gang box or suitable surface.
Make sure the wire bundle to the reader has an IP rating of at least IP65.
red
Cable Colours
black
yellow
orange
green
white
+5 to +12Vdc
ground
buzzer
green led
W0
W1
Warranty
Each reader comes with a 3 year warranty from the date of
dispatch. The warranty is void if the instructions contained
within this document have not been adhered to.
INS Global Pty Ltd
Suite 8
166a The Entrance Road
Erina NSW 2250
www.insglobal.com
Ph: 1300 203 373
Product of Australia
S1-P
INSTALLATION GUIDE
Model
INS - IG - B1 - R01
MAGNET
CUT OUT IN WALL REQUIRED :
52 x 70mm (2.05 x 2.76”)
FACIA
WALL
APPLY DOUBLE
SIDED TAPE
LED ORIENTATION
TAMPER REED SWITCH
LOCATION IF FITTED
FRONT VIEW SIDE VIEW
NOT TO SCALE