INS Global S3-P RFID card reader User Manual instrucitonmenu

Download:
Mirror Download [FCC.gov]
Document ID	3367295
Application ID	1w+3kbXINw+7YoiOmox3rQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.14kB (101740 bits)
Date Submitted	2017-04-23 00:00:00
Date Available	2017-04-23 00:00:00
Creation Date	2017-04-05 10:26:02
Producing Software	pdfFactory Pro 4.05 (Windows NT x64 10.00 Chinese (Simplified))
Document Lastmod	2017-04-20 13:54:40
Document Title	instrucitonmenu.xls
Document Creator	pdfFactory Pro www.pdffactory.com
Document Author:	taylor

INS serial 13.56M + 125k card reader
125K card reader and also 13.56MHz dual frequency card readers. INS serial products
are in different case but with same hardware in one set PCBA. It reads 13.56M mifare card
and 125K HID compitable cards, and with wiegand interface or RS485 as per customer's
request.
Model Name: S1,B1 etc
Product Picture
Specification:
Power requirement
Support card
Interface
Read range
Frequency
Operating temperature
Operating humidity
Audio/Visual Indication
Response Time
Cable length
Weight
Wiring :
Red: Power 5-16V
Black: Power ground
Green: Wiegand output D0
White: Wiegand output D1
Yellow: Buzzer
Orange: LED
5-16VDC at 100mA, A linear regulator is recommended
125K or 13.56M proximity cards and fobtags.
Weigand
5 - 10 cm
125.62KHz , 13.56M
-30°C to +60°C
5%-95% (non-condensing)
Green & Red and Buzzer signal output
Less than 0.2 seconds
250mm
100-200gram per different model
LED/Buzzer function description
LED function: The LED color is normally in RED. It starts with green flashe and will keep RED. When card is
detected successful, LED will flash green momentarily,this indicates cards were read properly . When LED
control signal is actived by access controller host, LED will changes to green.
Beeper Function: When Power up the reader, Beeper will ring 2 times. When cards is detected successful, a
short beep will be emitted. This indicates that HID card was read properly.
Buzzer control line
when this control line is actived to lower by access controller host or connect to Ground line, buzzer will kepp
ringing untill the line is released.
Green LED control line
when it is actived by access controller host or connect to ground line, Green LED will keep lighting untill the line
is released.
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly approved by INS
Global Pty Ltd may void the FCC authorization to operate this device.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : taylor
Create Date                     : 2017:04:05 10:26:02+08:00
Modify Date                     : 2017:04:20 13:54:40+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : taylor
Title                           : instrucitonmenu.xls
Creator Tool                    : pdfFactory Pro www.pdffactory.com
Metadata Date                   : 2017:04:20 13:54:40+08:00
Producer                        : pdfFactory Pro 4.05 (Windows NT x64 10.00 Chinese (Simplified))
Document ID                     : uuid:80bc4527-2167-435e-8694-2d934f924099
Instance ID                     : uuid:a1650294-89b1-4da7-aab0-2c072690bfba
Page Layout                     : SinglePage
Page Count                      : 2

EXIF Metadata provided by EXIF.tools