JOAN Technology C50 Bar code Hand Terminal User Manual PowerPoint

Shenzhen JOAN Technology Co., Ltd. Bar code Hand Terminal PowerPoint

Contents

  • 1. User Manual
  • 2. User_Manual

User Manual

Mobile Data Collection Terminal
Quick Guide
Overview
EARPIECE
SPEAKER
MEMU
RETURN
DATA INTERFACE
LED
HOME
SCAN
VOLUME+
VOLUME-
SCAN
POWER
CARD COVER
CAMERA
LANYARD HOLE
SCAN WINDOW
NFC & ID CARD
SENSING
Install SIM card
Use the card cover and the bottom cover to release the cover, as shown below
Install SIM card
Please press the view to select the corresponding slot to insert the SIM card, as follows
Double Card Specification
Your device use the design“double SIM card double standby ” The two SIM
cards unable to use voice and data service at the same time.
• If one SIM card is dialing then the other one unable to answer the phone. You
may hear“the phone you call is out of service and please call later”
• If one SIM is using the date service then the other one unable to use it at the
same time.
Your device support double SIM card double standby ,Please set one card to
use 4G service when you inserted two Nano-SIM cards.
Setting –dual card management, Please select 4G card slot set function as you
need and switch to 4G service.
•BLN-TL10 、BLN-AL10 ：mobile ,Unicom or telecom SIM cards to 4G service.
•BLN-TL00 ：SIM set to 4G card
Connect to WLAN network
一、Connect to WLAN network
1.Slide down the status bar and open the notification panel.
2.Click on the switch page and press long to enter the WLAN setting interface.
3.Open WLAN switch, The device will show the detected the WLAN network
on a list.
4.Click on the WLAN network you need. If you select an encrypted network,
Please enter passport.
Instructions on the Bluetooth
1.Click on device Bluetooth setting, Select“open”,Bluetooth support function is
available.
2.Bluetooth headset ,Press headset multifunction function more than 3 second
s until the indicator lights up（pay more attention the indicator light should be li
ght up steady not blink or not bright. Or some of them set is for the red and bl
ue flashing）
3. Open Bluetooth option on device and searching, the list with Bluetooth nam
e and model will be show, Please click on and enter password (usually 0000)
or no password. It is successfully once headset and indicator flashing quickly
4.Click on Bluetooth headset such as S10,open it and select binding. In this
way device have been connected with headset. In this time you may heard
“Dingdong "prompt.the same prompt can be heard when you closed the
Bluetooth headset. The prompt can be used to judge the Bluetooth headset
and phone has normal connection or not.
Online Upgrade
We have equipped you with an online upgrade function. You can
get the latest and most stable system through online upgrade. The
operation method is as follows:
1. Click main menu and enter APP menu interface
2. Click on the settings icon to enter the settings interface, click on
the "About phone" option,
In the selection click on "system upgrade" as shown
3. System upgrade adopts OTA upgrade mode. When a new
system is detected, it will automatically prompt whether to
upgrade.
Barcode Scanning
If your device is equipped with a barcode scanning function, please follow the
instructions
below to support 1D and 2D barcode scanning recognition
1. Click main menu and enter APP menu interface.
2. Click JSCAN enter scan function setting, see picture
3. JSCAN function description & feature:
3.0.1 open the scanner: Turn on or off the scan function.
3.0.2 Voice: After the bar code recognition is successful, the device will issue a voice prompt.
3.0.3 Vibration: After the barcode recognition is successful, the device vibrates.
3.0.4 Add enter: Barcode suffix adds carriage return character (line feed) after successful barcode recognition
3.0.5 Output focus: Scan the bar code at the cursor of the text box in any program interface, all can receive
bar code data
3.0.6 Boot up: The operating system will automatically start the scanner after rebooting
3.0.7 Continuous model: The program automatically triggers the scanning of the light to identify the bar code
3.0.8 Encoding: Received data conversion encoding（utf-8 or gbk）
3.0.9 Version: The version number of the program
3.1.0 Exit: Exit the program front interface, go to the background
3.1.1 JSCAN: The application of the scanning program for the system can facilitate the user to quickly and
easily experience the scanning and save the secondary development time.
4. Device trigger scan, see photo:
scan button
scan window
4.0.1 The device scan side button is divided into two sides, can trigger the scan
4.0.2 According to the bar code different size specifications to determine the scanning distance,
such as 18mm * 18mm specifications of the two-dimensional code, the best scanning distance
15-30cm
4.0.3 Scan angle: ±72, front and rear: ±72, swivel 360°scan
5. Recognizable type barcode, as shown：
UPC-A ,UPC-E ,EAN-13 ,EAN-8 , Code 39, Cross Code 25 , Matrix Code 25, Kudiba Code, Code 128 ,
UCC/EAN 128(GS1-128) , ISBT 128 , Code 93 , China Post Code ,China Finance Code ,GS1 DataBar ,
GS1 DataBar Truncated 3, GS1 DataBar Limited, GS1 DataBar Expanded, PDF417,
QR, DataMatrix .
NFC Read Function
If your device is equipped with an NFC read function, follow the instructions
below
1. Click the main menu button to enter the APP menu interface
NFC Sensing Area
(Remarks:NFC and ID reading functions are optional features. Please make sure that
your device has this feature to operate)
2. Click on the settings icon to enter the settings interface, click on the "more" option,
Then click to select "NFC" and finally click the button to turn on NFC
3. When the device touches the NFC card, the NFC program will automatically display the NFC
information, as shown in the figure.
4. Reading distance 3-5cm, using standard NFC
protocol
FQA
1. What should I do if the device does not boot?
(1) When the power button is pressed for 3-4 seconds, the screen
will start to display. Press the power button to release the power
button when the screen is displayed.
(2) Next, check if the device has power and connect it to the USB
cable of the device. If the battery charge icon is displayed on the
screen, it indicates that the battery power is insufficient.
2. Can't connect the device to the computer?
If the device is plugged into the computer's USB port, there is no
prompt, please replace a USB port and then test it, if you do not
have any response please replace the computer and try again
3. The device is out, but the bar code is not scanned?
This situation is generally a scan setting problem, you need to enter
the scan settings, first check the keyboard output options check, if
you have checked please reset the scan engine, the scan switch to
open a once off operation
4. How to use the battery correctly
The battery of the device is a polymer battery. Please charge the
device in time after being discharged. Do not store it for a long time
in the case of empty power or full power. The battery power should
be stored in the case of 50% or so.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.

User_Manual

Mobile Data Collection Terminal
Quick Guide
Overview
EARPIECE
SPEAKER
MEMU
RETURN
DATA INTERFACE
LED
HOME
SCAN
VOLUME+
VOLUME-
SCAN
POWER
CARD COVER
CAMERA
LANYARD HOLE
SCAN WINDOW
NFC & ID CARD
SENSING
Install SIM card
Use the card cover and the bottom cover to release the cover, as shown below
Install SIM card
Please press the view to select the corresponding slot to insert the SIM card, as follows
Double Card Specification
Your device use the design“double SIM card double standby ” The two SIM
cards unable to use voice and data service at the same time.
• If one SIM card is dialing then the other one unable to answer the phone. You
may hear“the phone you call is out of service and please call later”
• If one SIM is using the date service then the other one unable to use it at the
same time.
Your device support double SIM card double standby ,Please set one card to
use 4G service when you inserted two Nano-SIM cards.
Setting –dual card management, Please select 4G card slot set function as you
need and switch to 4G service.
•BLN-TL10 、BLN-AL10 ：mobile ,Unicom or telecom SIM cards to 4G service.
•BLN-TL00 ：SIM set to 4G card
Connect to WLAN network
一、Connect to WLAN network
1.Slide down the status bar and open the notification panel.
2.Click on the switch page and press long to enter the WLAN setting interface.
3.Open WLAN switch, The device will show the detected the WLAN network
on a list.
4.Click on the WLAN network you need. If you select an encrypted network,
Please enter passport.
Instructions on the Bluetooth
1.Click on device Bluetooth setting, Select“open”,Bluetooth support function is
available.
2.Bluetooth headset ,Press headset multifunction function more than 3 second
s until the indicator lights up（pay more attention the indicator light should be li
ght up steady not blink or not bright. Or some of them set is for the red and bl
ue flashing）
3. Open Bluetooth option on device and searching, the list with Bluetooth nam
e and model will be show, Please click on and enter password (usually 0000)
or no password. It is successfully once headset and indicator flashing quickly
4.Click on Bluetooth headset such as S10,open it and select binding. In this
way device have been connected with headset. In this time you may heard
“Dingdong "prompt.the same prompt can be heard when you closed the
Bluetooth headset. The prompt can be used to judge the Bluetooth headset
and phone has normal connection or not.
Online Upgrade
We have equipped you with an online upgrade function. You can
get the latest and most stable system through online upgrade. The
operation method is as follows:
1. Click main menu and enter APP menu interface
2. Click on the settings icon to enter the settings interface, click on
the "About phone" option,
In the selection click on "system upgrade" as shown
3. System upgrade adopts OTA upgrade mode. When a new
system is detected, it will automatically prompt whether to
upgrade.
Barcode Scanning
If your device is equipped with a barcode scanning function, please follow the
instructions
below to support 1D and 2D barcode scanning recognition
1. Click main menu and enter APP menu interface.
2. Click JSCAN enter scan function setting, see picture
3. JSCAN function description & feature:
3.0.1 open the scanner: Turn on or off the scan function.
3.0.2 Voice: After the bar code recognition is successful, the device will issue a voice prompt.
3.0.3 Vibration: After the barcode recognition is successful, the device vibrates.
3.0.4 Add enter: Barcode suffix adds carriage return character (line feed) after successful barcode recognition
3.0.5 Output focus: Scan the bar code at the cursor of the text box in any program interface, all can receive
bar code data
3.0.6 Boot up: The operating system will automatically start the scanner after rebooting
3.0.7 Continuous model: The program automatically triggers the scanning of the light to identify the bar code
3.0.8 Encoding: Received data conversion encoding（utf-8 or gbk）
3.0.9 Version: The version number of the program
3.1.0 Exit: Exit the program front interface, go to the background
3.1.1 JSCAN: The application of the scanning program for the system can facilitate the user to quickly and
easily experience the scanning and save the secondary development time.
4. Device trigger scan, see photo:
scan button
scan window
4.0.1 The device scan side button is divided into two sides, can trigger the scan
4.0.2 According to the bar code different size specifications to determine the scanning distance,
such as 18mm * 18mm specifications of the two-dimensional code, the best scanning distance
15-30cm
4.0.3 Scan angle: ±72, front and rear: ±72, swivel 360°scan
5. Recognizable type barcode, as shown：
UPC-A ,UPC-E ,EAN-13 ,EAN-8 , Code 39, Cross Code 25 , Matrix Code 25, Kudiba Code, Code 128 ,
UCC/EAN 128(GS1-128) , ISBT 128 , Code 93 , China Post Code ,China Finance Code ,GS1 DataBar ,
GS1 DataBar Truncated 3, GS1 DataBar Limited, GS1 DataBar Expanded, PDF417,
QR, DataMatrix .
NFC Read Function
If your device is equipped with an NFC read function, follow the instructions
below
1. Click the main menu button to enter the APP menu interface
NFC Sensing Area
(Remarks:NFC and ID reading functions are optional features. Please make sure that
your device has this feature to operate)
2. Click on the settings icon to enter the settings interface, click on the "more" option,
Then click to select "NFC" and finally click the button to turn on NFC
3. When the device touches the NFC card, the NFC program will automatically display the NFC
information, as shown in the figure.
4. Reading distance 3-5cm, using standard NFC
protocol
FQA
1. What should I do if the device does not boot?
(1) When the power button is pressed for 3-4 seconds, the screen
will start to display. Press the power button to release the power
button when the screen is displayed.
(2) Next, check if the device has power and connect it to the USB
cable of the device. If the battery charge icon is displayed on the
screen, it indicates that the battery power is insufficient.
2. Can't connect the device to the computer?
If the device is plugged into the computer's USB port, there is no
prompt, please replace a USB port and then test it, if you do not
have any response please replace the computer and try again
3. The device is out, but the bar code is not scanned?
This situation is generally a scan setting problem, you need to enter
the scan settings, first check the keyboard output options check, if
you have checked please reset the scan engine, the scan switch to
open a once off operation
4. How to use the battery correctly
The battery of the device is a polymer battery. Please charge the
device in time after being discharged. Do not store it for a long time
in the case of empty power or full power. The battery power should
be stored in the case of 50% or so.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.

Navigation menu