Johnson Controls Interiors HONUAHL3 Universal Garage Door Opener User Manual

Johnson Controls Interiors L.L.C. Universal Garage Door Opener Exhibit D Users Manual per 2 1033 b3

a href="https://usermanual.wiki/Johnson-Controls-Interiors" itemprop="url"> Johnson Controls Interiors >

Contents

Exhibit D Users Manual per 2 1033 b3

The Owners Manual for the Homelink® series Universal Garage Door Opener is reproducedhere.HomeLink® Universal TransceiverSuggested Owner’s Manual TextMarch 2002HomeLink® Universal TransceiverThe HomeLink® Universal Transceiver in your vehicle provides a convenient way to replace up to three hand-held transmitters with a single built-in component. This innovative feature will learn the radio frequencycodes of most current transmitters used to activate devices such as garage doors, entry door locks, estategates, security systems, and home or office lighting. For additional information on HomeLink and/orHomeLink compatible products, call 1-800-355-3515 or refer to the HomeLink web site atwww.homelink.jci.com.PrecautionsWhen programming the HomeLink Universal Transceiver to a garage door opener or entrygate, make sure that people and objects are out of the way to prevent potential harm ordamage.Do not use the HomeLink Universal Transceiver with any garage door opener thatlacks the safety stop and reverse feature as required by federal safety standards. (Thisincludes any garage door opener model manufactured before April 1, 1982.) A garagedoor opener which cannot detect an object, signaling the door to stop and reverse, doesnot meet current federal safety standards. Using a garage door opener without thesefeatures increases risk of serious injury or death. For more information, call1-800-355-3515 or on the internet at www.homelink.jci.com.Retain the original transmitter for future programming procedures (i.e., new vehiclepurchase). It is also suggested that upon the sale of the vehicle, the programmedHomeLink Universal Transceiver buttons be erased for security purposes (follow step1 in the “Programming” portion of this text).
ProgrammingNote: For best results, replace the battery in the hand-held transmitter with a new battery before programming. If your garage door opener receiver (located in the garage) is equipped with an antenna, make sure the antenna is completely uncoiled and hangs straight down.1. Press and hold the two outside buttons - releasing only when the indicator light begins to flash after 20 seconds. (This procedure erases the factory set default codes and does not have to be followed to program additional hand-held transmitters.)2. Hold the end of the hand-held transmitter of the device you wish to train approximately one to three inches away from the HomeLink surface - keeping the indicator light in view. (For placement questions, please contact HomeLink at 1-800-355-3515 or on the internet at www.homelink.jci.com.)3. Using both hands, simultaneously push the hand-held transmitter button and the desired HomeLink button. Do not release the buttons until step 4 has been completed. Note: Some entry gates and garage door openers may require you to replace this programming step (#3) with the procedures noted in the “Canadian Programming / Gate Programming” section.4. The HomeLink indicator light will flash, first slowly and then rapidly. Whenthe indicator light flashes rapidly, release both buttons. (The rapid flashing lightindicates successful programming of the new frequency signal.)If, after 20 seconds, the indicator light does not flash rapidly, release both the HomeLink and the hand-held transmitterbuttons and repeat steps two through four. However, position the hand-held transmitter at a different lengthand/or angle until the indicator light begins to flash rapidly. Release both buttons after the indicator light flashesrapidly.Refer to “Rolling Code Programming” and/or “Canadian Programming/Gate Programming” for additional proceduresif necessary.To activate the garage door or other programmed device upon successfully completing the steps above, press and holdthe HomeLink button - releasing when the device begins to activate.To program the remaining two buttons, follow steps 2 through 4.If you do not successfully program the HomeLink Universal Transceiver to learn the signal of the hand-heldtransmitter, refer to “Rolling Code Programming” within this text or call toll-free for customer assistance at 1-800-355-3515 or on the internet at www.homelink.jci.com.
Download:
Mirror Download [FCC.gov]
Document ID251623
Application IDOVGN7t4XSfw53L/Gcmnkyg==
Document DescriptionExhibit D Users Manual per 2 1033 b3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatMicrosoft Word - pdf
Filesize3.03kB (37889 bits)
Date Submitted2002-06-20 00:00:00
Date Available2002-06-20 00:00:00
Creation Date2002-06-20 17:12:21
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2002-06-20 17:12:23
Document TitleExhibit D Users Manual per 2 1033 b3
FCC ID Filing: CB2HONUAHL3

Navigation menu