Johnson Outdoors IPREM15 Remote Control Transmitter for Fishing Boat Motor User Manual i pilot manual 2377152revA indd

Download:
Mirror Download [FCC.gov]
Document ID	1557243
Application ID	4XKUTvj4UtOf0BFKTo5++A==
Document Description	manual pt 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	230.01kB (2875120 bits)
Date Submitted	2011-10-08 00:00:00
Date Available	2011-10-13 00:00:00
Creation Date	2011-07-01 17:26:38
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2011-07-01 17:26:38
Document Title	i-pilot_manual_2377152revA.indd
Document Creator	PScript5.dll Version 5.2
Document Author:	njohnson

Owner’s Manual
TABLE OF CONTENTS
Introduction ...................................................................................... 3
Two-Year Warranty ........................................................................ 4-5
Installation.................................................................................... 6-25
Parts List............................................................................................6-9
Preparing for Installation ....................................................................10
Installation of i-Pilot Controller......................................................11-27
Verifying Installation ..................................................................... 28-29
Getting Started........................................................................... 30-37
Knowing Your Remote ................................................................. 30-32
Knowing Your i-Pilot Controller ................................................... 33-36
System Startup ...................................................................................37
Manual Control........................................................................... 38-41
GPS Motor Control......................................................................42-61
Spot Lock ..................................................................................... 44-47
Cruise Control.............................................................................. 48-49
AutoPilot /Advanced AutoPilot .................................................... 50-55
Track Recording/Playback.............................................................56-61
Frequently Asked Questions........................................................ 62-63
Troubleshooting.......................................................................... 64-67
Glossary ..................................................................................... 68-69
Compliance Statements .............................................................. 70-71
Notes ......................................................................................... 72-73
© 2011 Johnson Outdoors Marine Electronics, Inc.
2377152 Revision A
I N TRO D UCT IO N
Overview
Thank you for purchasing the Minn Kota® i-Pilot®. This revolutionary control
system uses GPS technology to record and store tracks and locations which
are then used to deliver unprecedented levels of boat control. Intuitive
features and wireless control help to accurately position your boat and
improve your bait presentation. i-Pilot navigates and positions your boat for
you, so you can focus on fishing.
This i-Pilot Owner's Manual is divided into four main sections: Installation,
Getting Started, Manual Control, and GPS Motor Control. A waterproof and
easy-to-read Quick Reference Guide is also included as a supplement to the
User Guide, both of which can be stored in the boat for easy access.
A French version of the manual is available online at minnkotamotors.com
Une version français du manuel est disponible en ligne à minnkotamotors.com
Safety and Cautions
You are responsible for the safe and prudent operation of your vessel. We
have designed i-Pilot to be an accurate and reliable tool that will enhance boat
operation and improve your ability to catch fish. This product does not relieve
you from the responsibility for safe operation of your boat. You must avoid
hazards to navigation and always maintain a permanent watch so you can
respond to situations as they develop. You must always be prepared to regain
manual control of your boat. Learn to operate your i-Pilot in an area free
from hazards and obstacles.
Warranty and Registration
To receive all the benefits of your product warranty please fill out and mail
the warranty registration card. You may also register your product online at
minnkotamotors.com.
Correctly installing i-Pilot on a Minn Kota trolling motor will not void the
original motor warranty or the warranty of any previously installed
accessories. Installing i-Pilot will not extend the warranty of any Minn Kota
product it is being installed into or in conjunction with.
m i n n kot a m ot o r s . c o m
LIMITED T WO-YEAR WARRANT Y ON
ENTIRE PRODUCT:
Johnson Outdoors Inc. warrants to the original purchaser that the purchaser’s
entire i-Pilot System® accessory is free from defects in materials and
workmanship appearing within two (2) years after the date of purchase.
Johnson Outdoors Inc. will, at its option, either repair or replace, free of
charge, any parts found to be defective during the term of this warranty.
Such repair or replacement shall be the sole and exclusive liability of Johnson
Outdoors Inc. and the sole and exclusive remedy of the purchaser for breach
of this warranty.
These limited warranties do not apply to i-Pilot Systems used commercially,
nor do they cover normal wear and tear, blemishes that do not affect the
operation, or damage caused by accidents, abuse, alteration, modification,
misuse or improper care or maintenance. DAMAGE CAUSED BY THE USE
OF OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN
SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY
THIS LIMITED WARRANTY. The cost of normal maintenance or replacement
parts that are not defective are the responsibility of the purchaser.
To obtain warranty service in the U.S., the part believed to be defective and
proof of original purchase (including the date of purchase) must be presented
to a Minn Kota Authorized Service Center or to Minn Kota’s factory
service center in Mankato, MN. Any charges incurred for service calls,
transportation or shipping/freight to/from the Minn Kota Authorized
Service Center or factory, labor to haul out, remove, re-install or re-rig
products removed for warranty service, or any other similar items are the sole
and exclusive responsibility of the purchaser. i-Pilot systems purchased outside
of the U.S. (or parts of such systems) must be returned prepaid with proof of
purchase (including the date of purchase and serial number) to any
Authorized Minn Kota Service Center in the country of purchase. Warranty
service can be arranged by contacting a Minn Kota Authorized Service
Center listed on the enclosed sheet or by contacting the factory at
m i n n kot a m ot o r s . c o m
1-800-227-6433, 1-507-345-4623 or fax 1-800-527-4464. Note: Do not
return your i-Pilot or parts to your retailer. Your retailer is not authorized to
repair or replace them.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED
WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND TWO YEARS
FROM THE DATE OF PURCHASE. IN NO EVENT SHALL JOHNSON
OUTDOORS MARINE ELECTRONICS L.L.C. BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations and/or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other legal rights which vary
from state to state.
“WARNING: This product contains chemical(s) known to the state of
California to cause cancer and/or reproductive toxicity.”
m i n n kot a m ot o r s . c o m
PA RTS L I S T V I E W T E R ROVA
ITEM
PART
NUMBER
DESCRIPTION
2990270
I-PILOT CONTROLLER, TERROVA
2994170
REMOTE, ASSEMBLY I-PILOT
2372100
SCREW, #8-18 X 5/8" SS
4*
2377152
MANUAL, I-PILOT
5*
2377153
MANUAL, I-PILOT QUICK REFERENCE GUIDE
6*
2370817
LANYARD, REMOTE WITH CARABINEER
* Not Shown In Exploded View
QTY
min n kot a m ot o r s . c o m
INSTALLATION
PA RTS L I S T V I E W R I P T I D E S T
ITEM
PART
NUMBER
2990271
I-PILOT CONTROLLER, RIPTIDE ST
2994170
REMOTE, ASSEMBLY I-PILOT
2372100
SCREW, #8-18 X 5/8" SS
4*
2377152
MANUAL, I-PILOT
5*
2377153
MANUAL, I-PILOT QUICK REFERENCE GUIDE
6*
2370817
LANYARD, REMOTE WITH CARABINEER
DESCRIPTION
QTY
* Not Shown In Exploded View
min n kot a m ot o r s . c o m
PA RTS L I S T V I E W P OW E R D R I V E V 2
ITEM
PART
NUMBER
DESCRIPTION
2990272
I-PILOT CONTROLLER, POWERDRIVE V2
2994170
REMOTE, ASSEMBLY I-PILOT
2372100
SCREW, #8-18 X 5/8" SS
2224704
INSERT PLUG, BLACK SLOTTED
2376312
TIE, NYLON
2375403
HEAT SHRINK, .375 X 2 ADHESIVE LINED 3:1
2303430
SCREW - 1/4 - 20 X 5/8 - SELFTAP ZP
8*
2377152
MANUAL, I-PILOT
9*
2377153
MANUAL, I-PILOT QUICK REFERENCE GUIDE
10*
2370817
LANYARD, REMOTE WITH CARABINEER
* Not Shown In Exploded View
QTY
m i n n kot a m ot o r s . c o m
min
INSTALLATION
PA RTS L I S T V I E W R I P T I D E S P
ITEM
PART
NUMBER
DESCRIPTION
2990273
I-PILOT CONTROLLER, RIPTIDE SP
2994170
REMOTE, ASSEMBLY I-PILOT
QTY
2372100
SCREW, #8-18 X 5/8" SS
2224705
INSERT PLUG, WHITE SLOTTED
2376312
TIE, NYLON
2375403
HEAT SHRINK, .375 X 2 ADHESIVE LINED 3:1
10
2332104
SCREW - 1/4 - 20 X 5/8 SS
8*
2377152
MANUAL, I-PILOT
9*
2377153
MANUAL, I-PILOT QUICK REFERENCE GUIDE
10*
2370817
LANYARD, REMOTE WITH CARABINEER
* Not Shown In Exploded View
m i n n kot a m ot o r s . c o m
min
P R E PA R I N G F O R I N S TA L L AT I O N
Preparing for Installation
Tools you will need during installation
Terrova and Riptide ST
-Phillips screwdriver
PowerDrive V2
-Phillips screwdriver
-Needle-nose pliers
-Utility knife
-Heat gun or other heat source for installing heat shrink
Riptide SP
-Phillips screwdriver
-Needle-nose pliers
-Utility knife
-Heat gun or other heat source for installing heat shrink
To help with future service work or ordering replacement parts, please refer
to the information box in the Notes section located on page 74 of this manual.
Before installing i-Pilot on your motor, make sure the trolling motor is
properly installed on your boat. Find a clean and dry location for performing
the installation.
Most importantly, disconnect all power to the trolling motor before
installation. Not only will this protect you but also the sensitive electronics
you are about to install.
Read through the entire installation process before performing the installation.
If you need help or need further instruction on installing i-Pilot, please go
online at minnkotamotors.com for a full step-by-step, guided installation video.
You may also call Minn Kota technical service at 1-800-227-6433 to talk to a
customer service representative.
10
m i n n kot a m ot o r s . c o m
min
INSTALLATION
I N S TA L L AT I O N O F I - P I LOT
CON TRO L L ER
For PowerDrive V2 and Riptide SP trolling
motors go to page 13.
i-Pilot Installation on
Terrova and Riptide ST
Trolling Motors
*i-Pilot will override all CoPilot
functionality. CoPilot remotes will
not function with i-Pilot.
FIGURE 1
*The Terrova foot pedal is fully
functional and supported when i-Pilot
is installed correctly.
1. Remove all power to the
trolling motor.
2. Remove control box cover
screws and cover using Phillips
screwdriver. (Figure 1)
FIGURE 2
3. If the trolling motor has the
AutoPilot feature, unplug the
AutoPilot control board and
remove it from the control
box. (Figures 2 and 3)
FIGURE 3
m i n n kot a m ot o r s . c o m
min
11
4. Plug the i-Pilot controller
connector into the accessory
connector as shown.
(Figure 4) Be careful to
orient connector properly
prior to pushing together.
The plug will click twice when
pushing it together and
the yellow end will be fully
covered when installed
properly.
Make sure connector is
aligned properly. (Figure 5)
FIGURE 4
Make sure connector is fully
seated as shown. (Figure 5)
5. Place the i-Pilot controller
where the control box cover
was installed and secure with
supplied #8 screws. Do
not over tighten screws.
(Figure 6)
6. i-Pilot is now installed.
Proceed to page 28 to verify
your installation.
FIGURE 5
12
m i n n kot a m ot o r s . c o m
min
INSTALLATION
i-Pilot Installation on
PowerDrive V2 and
Riptide SP
*Note: Once i-Pilot is installed
in a PowerDrive V2 or Riptide SP
motor, the foot pedal cannot be
used again unless i-Pilot is
fully uninstalled.
1. Remove all power to the
trolling motor.
2. If a CoPilot is installed, it
must be removed as follows:
FIGURE 6
a. Disconnect motor
connector and foot pedal
connector from CoPilot.
(Figure 7)
b. Remove the CoPilot
receiver from the motor
by removing both
mounting screws. Do not
replace these screws as
the side plates will be
removed in step 13 of this
installation. (Figure 8)
FIGURE 7
FIGURE 8
m i n n kot a m ot o r s . c o m
min
13
3. Remove control box cover
screws and cover using Phillips
screwdriver. (Figure 9)
4. If the trolling motor has
AutoPilot it must be removed
as follows:
FIGURE 9
FIGURE 10
FIGURE 11
14
m i n n kot a m ot o r s . c o m
min
a. Disconnect all six
AutoPilot connectors from
AutoPilot controller, using
a needle-nose pliers and a
utility knife to remove any
heat shrink insulation that
may exist. (Figure 10)
b. Remove the AutoPilot
controller from the head
of the trolling motor.
(Figure 11) This is done by
pushing out the locking tabs
then lifting the circuit board
out. Finally lift out the
compass.
INSTALLATION
5. Remove grommet by pulling
back on coil cord strain relief
and pushing down on
grommet until it pops out.
(Figure 12)
Grommet
6. Review the cables in the head
of the trolling motor.
a. If a sonar cable is present,
it must be routed around
the outer perimeter of the
control box. The sonar
ground wire should also
be routed as shown.
(Figure 13)
FIGURE 12
Sonar Cable (Universal Sonar Motors Only)
b. The motor power wires
must be routed as shown.
(Figure 13)
Sonar
Cable
Sonar
Ground
Wire
Power Wires
AutoPilot Wires
(AutoPilot Motors Only)
FIGURE 13
m i n n kot a m ot o r s . c o m
min
15
7. Route i-Pilot controller cable
through grommet hole and
through center of coil cord.
(Figure 14)
8. If AutoPilot was removed,
insulate the loose AutoPilot
connectors as follows:
FIGURE 14
FIGURE 15 Insert AutoPilot wires into terminal holders.
a. For PowerDrive V2
Motors: Using a
needle-nose pliers push
all six AutoPilot connectors
that were disconnected in
step 4 onto terminal
holders located on the
underside of the i-Pilot
Controller. (Figure 15)
IMPORTANT: Pull on
each wire to make sure it
is secured properly. Loose
wires can cause damage to
i-Pilot Controller and the
entire motor.
AutoPilot connectors
must be placed onto
holders exactly as shown.
(Figure 16)
FIGURE 16
16
m i n n kot a m ot o r s . c o m
min
INSTALLATION
b. For Riptide SP Motors:
Apply heat shrink insulation
supplied in bag assembly
to the ends of all six loose
AutoPilot connectors as
shown. (Figure 17) Use a
zip tie to bundle connectors
together. Trim the zip tie
and place connector bundle
in the middle of the control
box as shown. (Figure 18)
Pinch ends of heat
shrink shut using
needle-nose pliers.
FIGURE 17 Insulate and seal six AutoPilot wires on
Riptide SP motors with supplied heat shrink.
FIGURE 18 Place insulated AutoPilot wires in the
bottom center of the control box as shown.
m i n n kot a m ot o r s . c o m
min
17
9. Install new grommet supplied
with i-Pilot by snapping it into
the hole located in front of
the coil cord strain relief. The
i-Pilot controller cable must be
placed in the pass-through slot
of the grommet. (Figure 19)
FIGURE 19
10. Place the i-Pilot controller
where the control box cover
was installed. Pull any extra
controller cable out of the
control box by gently pulling
on the cable. (Figure 20)
11. Secure cover with supplied
#8 screws. Do not over
tighten screws. (Figure 21)
FIGURE 20
FIGURE 21
18
m i n n kot a m ot o r s . c o m
min
INSTALLATION
12. Secure the i-Pilot controller
cable to the motor coil cord in
all three locations shown using
zip ties provided. (Figure 22)
Trim zip ties using utility knife.
Failure to secure cable will
result in possible damage to
the cabling during operation.
13. Remove the left and right
side plates of trolling motor
by loosening all four side
plate screws using a Phillips
screwdriver. (Figure 23)
Zip Tie
Location 1
Zip Tie
Location 2
Zip Tie
Location 3
FIGURE 22
FIGURE 23
m i n n kot a m ot o r s . c o m
min
19
14. Remove center housing by
pushing in on both sides
and lifting up at the same
time. This will expose the
main control board and
wiring. (Figure 24)
FIGURE 24
FIGURE 25
20
Entrance of steering cable through center housing
Disconnect both wires by removing heat shrink and pulling them apart.
m i n n kot a m ot o r s . c o m
min
INSTALLATION
15. The steering motor cable
passes through the top of the
center housing removed in
step 14. This cable contains
a black and white wire.
Disconnect these two wires
by pulling each connector
apart. (Figure 25) Riptide SP
motors will have this
connections covered with
heat shrink which must be
removed with a utility knife.
16. Loosen the cable strain
relief that is secured to the
base of the motor and install
the i-Pilot controller steering
cable into the open strain
relief slot. (Figure 26)
FIGURE 26
m i n n kot a m ot o r s . c o m
min
21
17. Tighten the cable strain
relief as shown. The
i-Pilot controller steering
cable should slide freely
through the strain relief
when installed properly.
(Figures 27 and 28)
Foot Pedal Cable
Motor Power Cable
i-Pilot Controller
Steering Cable
Reinstall strain
relief screw.
FIGURE 27 and 28
22
m i n n kot a m ot o r s . c o m
INSTALLATION
18. Slide four pieces of heat
shrink insulation over each
side of the wires that were
disconnected in step 15.
(Figure 29)
Slide heat shrink
over steering
motor wires.
FIGURE 29
m i n n kot a m ot o r s . c o m
min
23
19. Connect the black and white wires
from the i-Pilot controller cable to
the back and white steering motor
wires, making sure black is
connected to black and white is
connected to white. (Figure 30)
Connect steering wires:
white to white
black to black
FIGURE 30
24
m i n n kot a m ot o r s . c o m
min
INSTALLATION
20. Complete the installation by
positioning the heat shrink
over the connections and
shrink down, using a heat
gun or other heat source,
being careful not to
overheat any wire or parts.
Seal connections with
heat shrink.
IMPORTANT: DO NOT
OVERHEAT WIRES OR
SURROUNDING PARTS
WHEN INSTALLING
HEAT SHRINK!
21. Reinstall center housing
over control board by
pushing it down until the
side fingers lock into
place. The new i-Pilot
Controller steering cable
should be exiting the cable
exit hole at the center and
bottom of the center housing.
(Figure 31)
FIGURE 31
m i n n kot a m ot o r s . c o m
min
25
FIGURE 32
FIGURE 33
26
m i n n kot a m ot o r s . c o m
min
INSTALLATION
22. Reinstall both side plates using
Phillips screwdriver. If a
Co-Pilot was uninstalled, use
new ¼-20 X 5/8" Phillips screws
provided. (Figure 32)
23. If a foot pedal is connected to
the trolling motor, it must be
disconnected. Once i-Pilot has
been installed the foot pedal
cannot be used unless i-Pilot is
completely uninstalled.
24. Connect i-Pilot controller cable
to the foot pedal connector,
making sure the connector nut is
tight. (Figure 33)
IMPORTANT: DO NOT place
dielectric grease or any type of
lubricant in the connector.
25. i-Pilot is now installed.
m i n n kot a m ot o r s . c o m
min
27
V E R I F Y I N G I N S TA L L AT I O N
It is important to verify your i-Pilot installation prior to going on the water. If
this cannot be done, it is highly recommended that system verification be done
in an open area on a calm day with a fully operational outboard motor for a
backup means of powering your boat.
To verify that i-Pilot is working properly before going on the water, follow the
steps below.
1. Trolling motor should be correctly installed and mounted to the bow
of a boat.
2. The boat and trolling motor must be located outside and have a direct
view of the sky to obtain GPS satellite signals.
3. Verify that all obstructions are away from the prop in all directions in both
the stowed and deployed positions.
4. Connect power to the trolling motor.
5. Deploy the motor so the motor shaft is completely vertical.
6. i-Pilot will emit four short beeps on startup.
7. Press any button on the i-Pilot remote.
8. The i-Pilot remote LCD will come on; prop speed and the GPS antenna
icon will be displayed. It should take no longer than two minutes to obtain
a GPS signal strength of at least one bar.
28
m i n n kot a m ot o r s . c o m
min
INSTALLATION
9. When i-Pilot is powered up, it starts to gather satellite information about
its location. A minimum satellite signal level must be achieved before all
i-Pilot functionality is available. This minimum level is one bar on the GPS
signal icon. At initial startup only manual functions will be available.
10. Verify all manual functions by pressing
and
11. If you experience any problems with any of the
steps above, or cannot obtain a GPS satellite
signal, refer to the troubleshooting section
beginning on page 64.
m i n n kot a m ot o r s . c o m
min
29
K N OW I N G YO U R R E M OT E
Layout
The i-Pilot remote is divided into four sections: Manual Control, Tracks,
Spot Lock, and Cruise Control/AutoPilot. Buttons in the Manual Control
section of the remote do not require a GPS signal to operate and give you full,
immediate control over steering, speed and prop functions similar to a CoPilot.
All other buttons require a minimum GPS signal strength of one bar in order
to operate. Buttons located in the Tracks section are used for track recording
and playback. Spot Lock buttons are located in the Spot Lock section. Cruise
Control/AutoPilot are located in the Cruise Control/AutoPilot section.
Construction
The remote is waterproof and floats in water.
Range
The range of the remote will be greatly reduced if it is used near or mounted
to any metal object including aluminum or steel. It is also recommended that
the front end of the remote not be obstructed during use.
Battery Life
Remote battery life is subject to frequency of use and is especially impacted by
how often the LCD backlight is used.
will appear on the remote LCD. The
When the remote battery is low,
is displayed to conserve battery power.
Backlight button will be disabled when
Power
When a button is pressed on the remote it will automatically turn on. To turn the
for three seconds. The remote will automatically
remote off press and hold
turn itself off thirty minutes after the last button press if a learned i-Pilot controller
is powered up and within transmitting range. The remote will turn off after three
seconds if the i-Pilot controller is powered down or out of transmitting range.
Keypad Lock
The user can lock the keypad during use to help avoid accidental key activations.
for 3 seconds. When the
To lock or unlock the keypad, press and hold
keypad is locked, will appear on the remote LCD. Note that the keypad is
always unlocked when the remote is first turned on.
30
min n kot a m ot o r s . c o m
GETTING STARTED
min n kot a m ot o r s . c o m
31
Remote Battery Replacement
1. Make sure hands are clean, dry and
static free. Discharge any static
electricity by touching a metal object
that is grounded. *Static electricity
can damage the circuit board.
FIGURE A
2. With the remote upside down, use a
large coin to rotate the battery door
counterclockwise until either of the
Unlock icons align with the arrow
(see Figure B).
3. Remove battery cover and old battery and replace with new CR2450 coin
cell battery. Note the proper polarity of the battery (see Figure A).
4. Ensure the two rubber o-rings are properly seated in the underside of the
battery cover.
5. Replace battery cover by aligning either of the Unlock icons with the
arrow, pressing the cover down and rotating clockwise until the Lock icon
aligns with the arrow (see Figure C).
FIGURE B
32
m i n n kot a m ot o r s . c o m
min
FIGURE C
GETTING STARTED
K N OW I N G YO U R
I -P I LOT CO N T RO L LER
Construction
The i-Pilot controller contains a very
sensitive digital compass and is where all
GPS satellite and i-Pilot remote signals are
received. It is very important that the
controller have a clear view of the sky in
all directions and has a clear line of sight to
the remote for optimum performance.
All electronics within the controller
i-Pilot
enclosure are completely sealed.
Speaker
Remote Learn
Button
Remote Learning
The i-Pilot remote is prelearned to the controller from the factory. The top of
the controller has a single learn button to allow additional remotes to be added
to the system. To learn additional remotes:
1. Power up the trolling motor.
2. Push and hold the learn button down. A steady audio tone will be heard
while holding this button.
3. While holding the learn button down push any button on the remote
being programmed. Three beeps will be heard when the remote is
successfully learned.
A remote can only be learned to one controller at a time. A controller can have
an unlimited number of remotes learned to it. During the learn process, the
remote must start out in the OFF condition. If necessary, the remote can be
turned off by pressing and holding the Pause button for three seconds.
m i n n kot a m ot o r s . c o m
min
33
Audio Modes
The i-Pilot Controller also contains an internal speaker which can be
programmed to work in two different audio modes. The speaker is
programmed to operate in audio mode one from the factory. To enable
and
down at the same time for three
different audio modes hold
seconds. For an explanation of each audio mode and their sounds see the
table below.
WHAT CONDITION CAUSES IT
Startup
Manual prop on
Manual prop off
Speed + (when less than max speed)
Speed - (when greater than speed 0)
High Speed Bypass enable
High Speed Bypass disable
Button press for any of these (enable
or disable): REC, Pause, Track to
Start, Track to End, AutoPilot, Cruise
Control, Spot Lock, Spot Lock Recall
Moving more than a quarter mile
from the last track point while in
Record Pause mode
When GPS Signal Strength goes to
no bars while in a GPS-based mode
34
m i n n kot a m ot o r s . c o m
min
AUDIO
MODE
Modes 1 and 2
Mode 2
Mode 2
Mode 2
Mode 2
Mode 2
Mode 2
Mode 2
AUDIO
PATTERN
4 Short beeps
Single beep
Double beep
Single beep
Single beep
Single beep
Double beep
Single beep
Mode 2
Error
Mode 2
Error
GETTING STARTED
WHAT CONDITION CAUSES IT
Attempting to enable a GPS
feature when no signal strength
bars are shown
Attempting to replay a Track or
recall a Spot Lock location when the
boat is beyond the minimum distance
MOM button on the footpedal is
pressed and a remote button press
attempts to override it
End of track attained during track
playback (in conjunction with
cancelling mode and turning the
prop off)
Switch to Audio Mode 1
Switch to Audio Mode 2
Learn button is pressed
Learn successfully completed
AUDIO
MODE
Mode 2
AUDIO
PATTERN
Error
Mode 2
Error
Mode 2
Error
Mode 2
High-Low,
High-Low,
High-Low
Modes 1 and 2
Modes 1 and 2
Modes 1 and 2
Modes 1 and 2
Single beep
Double beep
Steady tone
3 longer beeps
m i n n kot a m ot o r s . c o m
min
35
Power
The i-Pilot controller will turn on whenever the trolling motor has power. For
Terrova and Riptide ST motors this is when the green system ready light is on.
For PowerDrive V2 and Riptide SP motors this is whenever the motor is
connected to power.
* For this reason it is very important to disconnect a PowerDrive V2 or Riptide
SP motor from power when not in use or battery drain will occur.
Accuracy
The accuracy and responsiveness with which i-Pilot controls your boat is highly
dependent upon many variables. Just a few of these variables and their general
effects on responsiveness and accuracy are given below so that the behavior of
the system can be understood.
VARIABLE
EFFECT
Ratio of motor thrust Excessive thrust on a smaller boat can cause i-Pilot to
to boat weight
overcorrect. Not enough thrust on a large boat can
cause i-Pilot to respond slowly.
Wind
Excessive wind and/or current can reduce i-Pilot’s
positioning accuracy.
GPS signal strength
The greater number of GPS signal bars the greater
the accuracy.
Trolling motor
A fully charged battery will give the best performance.
battery power level
36
m i n n kot a m ot o r s . c o m
min
GETTING STARTED
System Startup
Once you have verified i-Pilot’s installation it’s time to start using it on the
water. Follow these simple steps each time you power up your trolling motor
for successful operation:
1. Connect trolling motor to power.
2. Deploy trolling motor into water.
Push any button on your remote. The remote LCD will show prop speed
and GPS signal strength.
4. You are now able to use all manual functions:
and
5. After i-Pilot has obtained a minimum GPS signal strength of one bar, all
remaining functions will become available.
m i n n kot a m ot o r s . c o m
min
37

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Create Date                     : 2011:07:01 17:26:38-05:00
Modify Date                     : 2011:07:01 17:26:38-05:00
Metadata Date                   : 2011:07:01 17:26:03-06:00
Creator Tool                    : PScript5.dll Version 5.2
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 8384 bytes, use -b option to extract), (Binary data 9557 bytes, use -b option to extract)
Document ID                     : uuid:8B8D231B31A4E011A1FBA59F8238CAC1
Instance ID                     : uuid:4476db34-724d-4c9f-bbba-5d70de2c4dfb
Derived From Instance ID        : uuid:d57d3f99-3f75-41fa-8c4a-42703e5450fe
Derived From Document ID        : xmp.did:058011740720681197A5B44AFE9FE613
Derived From Version ID         : 1
Derived From Rendition Class    : proof:pdf
Doc Change Count                : 8936
Format                          : application/postscript
Title                           : i-pilot_manual_2377152revA.indd
Creator                         : njohnson
Page Count                      : 37
Author                          : njohnson

EXIF Metadata provided by EXIF.tools