Keymat Technology DS40 AXS Series S40 iClass SE PIN-Contactless Reader User Manual DS40 xx 08KT

Download:
Mirror Download [FCC.gov]
Document ID	2641834
Application ID	mMfpgabahpnmW9wSS3TA7g==
Document Description	Datasheet
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.08kB (125961 bits)
Date Submitted	2015-06-09 00:00:00
Date Available	2015-06-09 00:00:00
Creation Date	2015-05-11 10:08:57
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2015-05-11 10:08:57
Document Title	Microsoft Word - DS40-xx-08KT
Document Creator	PScript5.dll Version 5.2.2
Document Author:	johns

AXS Series S40 Keypad
AXS SERIES S40 iCLASS SE® PIN-Contactless Reader: This integrated keypad and contactless reader is rated for continuous
outdoor use in exposed, unsupervised locations. Featuring genuine HID™ iCLASS SE®, Seos®, contactless technology, this
access control keypad offers enhanced security by dual factor authentication. Authorized access through a secured door or barrier
can be gained by entry of a valid PIN and/or presentation of an authorized 13.56 MHz IS014443 contactless credential
Installation
- Using the case as a template, mark the position of the four holes (A) on the surface.
(or if fixing to an already installed UK or US back box use the relevant hole pattern)
- Drill and plug the fixing holes to suit fixing screws (supplied).
- Run the cable through the sealing grommet
- Secure the case to the surface using the fixing screws
- Make the electrical connections to the connector block
- Plug the connector block into the keypad
- Make sure the rubber seal is located on the rear case.
- Fix the keypad to the rear case using the security screws
(Use the nylon sealing washers under the screw heads)
- Check the installation to ensure the rubber seal is in place and
compressed evenly around the perimeter of the case.
Weigand Format for PIN
Wiring Connections
Factory default is Weigand 8 bit burst format (for PIN).
If you need Weigand 4 bit burst format follow the sequence below.
Press #
on power up ,
LED FLASHES
RED/GREEN
Press #725
to enter format mode
Press 1
or
for FORMAT
for RESET TO DEFAULT
Press 0
or
for 4 BIT FORMAT
for 8 BIT FORMAT
Press 0
to EXIT,
LED STAYS RED
+5V
BEEP
DATA HOLD
TAMPER
0V
0V
RED LED
GREEN LED
+12V
WEIGAND DATA 1
WEIGAND DATA 0
TAMPER
Power Input. Connect only 5V OR 12V power
Active Low
Holds card data only – Active Low
Normally closed to 0V, open on tamper
Power
Power
Active Low
Active Low
Power input. Always use 12V for S40i
Open Collector output
Open Collector output
Normally open – connects to 0V on tamper
Specification
Card Compatibility
Card Read Range
Card Security
Coupling Frequency
Supply
Cable distance to host
Tamper detection
Status Indication
Credentials
iClass® , Mifare® , ISO15693, ISO14443A & B
2-5cm (depending on card)
V1 Security (Elite to special order only)
13.56 MHz
5V or 12V DC 200 mA (Use 12V, 250mA for Illuminated Keypad)
150m max
Normally open or closed
RED/GREEN as driven by the Controller
Performance
Operational Temp
Weather Resistant
Vibration & Shock
Impact Resistance
Certification
iCLASS
Seos
MIFARE Classic
MIFARE PLUS
MIFARE Ultralight
DESFire 0.6
DESFire EV1
As supported by the Controller
Order Codes
-35°C to +65°C
IP65
ETSI 6M3
IK09 (10J Rating)
CE / FCC / UL294
DS401KT20
DS402KW20
AXS Series S40 Keypad Metal Keys
AXS Series S40i Keypad Illuminated Keys
1KFS020
RC12020
Privacy Shield
Rear Case Kit (Spare)
FCC ID 2AEEZ-DS40. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
DS40-xx-08KT
Rev 1 Mar 2015
Page 1 of 1
For more information visit www.storm-interface.com
© Copyright Storm Interface. 2014. All rights reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : johns
Create Date                     : 2015:05:11 10:08:57+01:00
Modify Date                     : 2015:05:11 10:08:57+01:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 11.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - DS40-xx-08KT
Creator                         : johns
Document ID                     : uuid:7eab3810-ac9d-41ab-9839-f4b3fc6cb35e
Instance ID                     : uuid:45ed7b39-7e96-4f09-96a6-7e6ac7c2ee3c
Page Count                      : 1

EXIF Metadata provided by EXIF.tools