Krups Xp4050 Users Manual

Espresso Maker XP 4050 XP4050_eng

XP4050 to the manual 67d9b986-150e-426f-99c1-560091824ac0

2015-01-21

: Krups Krups-Xp4050-Users-Manual-220120 krups-xp4050-users-manual-220120 krups pdf

Open the PDF directly: View PDF .
Page Count: 9

1 cup

2 3

45 6

=x2

19 20 21

16 17

27 05

www.krups.com

Espresso Art. XP4050

Description

aTank lid

bRemovable water tank

cWarming plate for cups

dCoffee buttons ( , )

eStart / Stop switch with blue

operating control lamp

fHot water button ()

gSteam button ( )

hBrewing head

ISteam nozzle

JAuto cappucino accessory

kGrid

lDrip tray

mFilter holder

nFilter for one or two cups (ground

coffee)

oESE filter

pStorage for filter sieves

qClaris water filter*

rMeasuring spoon

* depending on model

Safety recommendations

• Please read these instructions carefully

before first using your espresso. The

appliance must only be connected to the

mains via an earthed plug. Check that the

voltage shown on the appliance’s indicator

plate corresponds to that of your electricity

system.

It complies with the requirements of the EEC

Directive (89/336/EEC) and (72/23/EEC).

• Never put your espresso on a hot surface

(electric warming plate, for example) or close

to a flame. Place on a flat, stable heat-

resistant surface.

• Never remove the filter holder containing

the coffee grounds while water is being

passed through, since the appliance is under

pressure at this time.

• Never use the appliance if the drip plate and

the grid are not in position.

• Disconnect the electricity if there is any

problem while the coffee is brewing or prior

to cleaning your appliance.

• Never unplug the appliance by pulling on

the cord and never lay the cord across a

sharp edge or the corner of an item of

furniture.

• Do not allow the cable or your hands to

come into contact with the hot parts of the

appliance (cup warming plate, filter holder,

steam nozzle, cappucino accessory).

• Never immerse the appliance in water.

• Keep away from children and do not allow

the cord to hang down.

• Follow the instructions given for descaling.

• Never start the machine if it is damaged or if

the cord is in poor condition.

• If the cord or any other specific part

becomes defective, these can only be

replaced by a Krups approved service centre.

You must never, under any circumstances,

open the appliance yourself, in order to

avoid any danger.

• Check that the filter holder is firmly in

position before starting the coffee and reset

the selector to O before releasing the filter

holder.

• Do not leave the appliance in the reach of

unsupervised children - young children and

severely handicapped persons must only use

the appliance under the supervision of a

responsible adult.

• This product has been designed for domestic

use only. Any commercial use, inappropriate

use or failure to comply with the instruc-

tions, the manufacturer accepts no

responsibility and the guarantee will not

apply.

Espresso coffee

Espresso coffee is richer in aroma and stronger

than normal coffee. It is drunk from small pre-

heated espresso cups. Hot water is passed

through the ground coffee to obtain this

delicious black coffee.

English

XP 4050_Europe.P65 28/01/05, 13:5614

Espresso Art. XP4050

You can recognise an espresso by its

characteristic aroma and its typical crema. But

this requires high pressure and an excellent

fresh espresso coffee which has been well

roasted and correctly ground.

If you cannot buy espresso ground coffee, use

a coffee grinder to grind the beans.

So as to obtain a sufficient crema with a good

colour, it is normal that the flow rate of the

coffee is slower than with a filter coffee

machine.

To guarantee complete success for your

espresso, you must also use freshly-drawn

water (so that it has not had time to stagnate

in the air), without any chlorine odour and at

a fairly cold temperature.

The coffee must not be ground too fine. It

must be slightly granulated. If it is too fine,

you risk blocking the grid of the brewing

head and the filter. Only use Espresso ground

coffee. Do not use any other type of coffee

such as filter, cafetiere, instant etc.

Before first using your machine

Before using your appliance for the first time,

clean the water heating system, without

coffee in the filter holder, filling the water

tanks once or twice, as follows:

• Open the lid and lift out the water tank

using the handle (1). Fill with water (2).

• Replace the tank, positioning it firmly to

ensure that water can enter, and close the

lid (3).

• Press the Start/Stop switch (4) whereby the

blue operating control lamp blinks. Two

filters are kept in the tank lid.

• Place one of the filters in the filter holder

(5). Then put the filter holder on the

appliance’s brewing head.

• To ensure that the filter holder is in the

correct position, turn the handle so it points

to the left (6), place the filter holder flat

against the brewing head, then turn the

handle towards the right (7) as far as it can

go (may not be at right-angles).

• Place a container, as large as possible,

beneath the filter holder (8).

• As soon as the blue operating control lamp

glows continuously,

The appliance is ready to operate.

• Pressing the double coffee button (10)

will now cause water to run through the

water circuit.

Repeat this process five times.

As an optional extra, there is a filter

cartridge available (N° art. F088 not

delivered with the appliance).

Using the various functions of

your espresso machine

1. MAKING AN ESPRESSO

.WITH ESPRESSO GROUND COFFEE

For best results, we recommend that you first

pre-heat the accessories (filter holder, filter

and cups) without putting in ground

coffee. To do this :

• Fill the water tank (1) (2) (3) and start the

appliance (4).

• Put the filter holder in place (6) (7), and

place one or two cups underneath.

• As soon as the control lamp on the coffee

buttons glows continuously, the appliance is

ready to operate.

• Press the coffee keys or (9) (10).

• The cups will be filled with hot water then

empty them.

Once the appliance is hot, the espresso cups

can then be pre-heated on the cup warming

plate.

. Preparing an espresso :

• Fill the water tank (1) (2) (3) and start the

appliance (4).

• Put the filter for one or two cups into the

filter holder (5).

• Put one or two measures of ground coffee

into the filter with the measuring spoon and

tamp down using the measuring spoon (11)

(12).

• Remove any ground coffee which is lying

around the filter (13).

• Replace the filter holder (6) (7).

XP 4050_Europe.P65 28/01/05, 13:5615

• Place one or two espresso cups beneath the

filter holder.

As soon as the control lamp on the coffee

buttons glows continuously, the appliance is

ready to operate.

Your appliance is already preprogrammed for

the preparation of one or two cups of

espresso.

• Pressing the coffee keys or (9) (10).

• At the beginning, there is a pre brewing

time lasting 2 or 3 seconds.

• When the programmed quantity is reached,

the espresso stops running automatically.

• Remove the filter holder and the filter from

the machine and take out the coffee

grounds (14).

The filter can be refilled to make more

espressos.

. WITH THE SPECIAL «ESE» FILTER

The E.S.E. system was designed for making

Italian-style espresso ristreto (squeezed). The

amount of coffee is 35 ml and the water

should take 20 seconds to run through.

(see Individual Programming to adjust volume)

«ESE», which stands for «Easy Serving

Espresso» , is a selected measure of coffee,

ground and pressed between two filter papers

making it ready for use. This system makes it

easy for you to prepare your espresso because

you avoid the measurement and tamping

down operations and it also makes it easier

for you to clean the appliance.

We do not intend, or recommend, that

the ESE servings are used for making a

long coffee.

We recommend that you take care, when

handling and storing the ESE servings, that

they do not become deformed.

For best results, we recommend that you pre-

heat the accessories (filter holder, filter and

cups) without any coffee. Do this as described

in the Making an Espresso using Espresso

Ground Coffee section.

. Preparing an espresso:

• Fill the water tank (1) (2) (3) and start the

appliance (4).

• Place the ESE serving in the ESE filter (18).

Tear excess paper from the pod at the

perforated edge. Place the ESE pod with the

RED MARKING FACE DOWN (bend the paper

corners down).

•Take care to put all the paper inside the filter

to avoid any drips.

Placing the ESE pod correctly will create a

richer, thicker crema.

• Put the filter holder in place (6) (7) (8) by

pressing it firmly to the right.

As soon as the control lamp on the coffee

buttons glows continuously, the appliance is

ready to operate.

• Press the coffee key (9).

• At the beginning, there is a pre-brewing

time lasting 2 or 3 seconds.

• When the recommended quantity of coffee

has been reached (35ml), press the coffee

button (9) if suitable volume was not

preprogrammed.

• Remove the filter holder from the brewing

head and throw away the used measure.

. Individual Programming:

Should you wish to alter the preprogrammed

quantity (50ml per cup, manufacturing

setting) of hot espresso filled into one or two

cups, proceed as follows:

• Fill the water tank (1) (2) (3) and start the

appliance (4).

• Put the filter for one or two cups into the

filter holder (5).

• Put one or two measures of ground coffee

into the filter with the measuring spoon and

tamp down using the measuring spoon (11)

(12) or a ESE pod in the ESE filter (18).

• Remove any ground coffee which is lying

around the filter (13).

• Replace the filter holder (6) (7).

• Place one or two cups beneath the filter

holder.

• As soon as the control lamp on the coffee

buttons glows continuously, the appliance is

ready to operate.

• Hold down either the one or two cups key

or (9) (10) (for at least 3 sec) , the

two lamps (coffee key and operating control)

blink.

XP 4050_Europe.P65 28/01/05, 13:5616

When the desired quantity of espresso has run

through, you stop by pressing the coffee key

or (9) (10).

Now the quantity is automatically memorized.

. Hot Water Preparation

You can prepare hot water with this

appliance.

• Fill the water tank (1) (2) (3) and start the

appliance (4).

• Place the cup beneath the auto cappuccino

accessory.

• As soon as the control lamp on the hot

water button glows continuously, the

appliance is ready to operate.

• Pressing the hot water button (15).

• When the desired quantity of water has run

through, you stop by pressing the hot water

key (15).

2. STEAM FUNCTION

The tapping noise which occurs while steam is

being produced comes from the intermittent

operation of the pump and has no effect on

the proper working of the appliance.

Beware: during and after use of the machine,

the metallic parts of the auto cappuccino

accessory can become burning hot.

. Using the auto cappuccino accessory

The auto cappuccino accessory makes it easy

to produce frothy milk for making a cappuc-

cino, a latte or a hot chocolate.

• Fill the water tank (1) (2) (3) and start the

appliance (4).

• Put the auto cappuccino accessory in place

on the steam nozzle.

• Place a cup under the auto cappuccino

accessory.

• Pour about 100 ml of very fresh, very cold

milk into a container. The milk and its

container must be well chilled.

• Insert the flexible tube into this container or

directly into the milk carton (17).

Please note the straight cut end of tube must

fit inside auto cappuccino device and the

irregular end dipped in milk.

• Turn the setting knob to the position

“cappuccino” or ‘ latte “.

• When the appliance is ready (operating

control lamp glows continuously), press the

steam button (16), the operating control

lamp blinks.

• When the control lamp of steam button

glows continuously again, appliance is ready

for steam.

• Press the steam button (16).

• Once the froth has been produced, stop by

pressing the steam button (16) for the

following cleaning operation in order to

prevent the milk from drying on the auto

cappuccino accessory.

• Place a cup under the auto cappuccino

accessory.

• Immerse the flexible tube into a clean

container 1/3 full of water.

• Press the steam button (16) and when all

the water has run through, press the steam

key (16) to stop.

• Next, clean the auto cappuccino accessory

with a damp cloth.

For more thorough cleaning of the auto

cappuccino accessory, please refer to the

paragraph on maintenance.

. Hot chocolate

• Repeat the same procedure as below after

changing the milk with a chocolate beverage

you want to heat up.

• If your espresso machine is ready for steam -

for 5 min without use, the appliance

switches automatically to coffee stand by.

If you wish to make an espresso immediately

after steam, the appliance must first be

allowed to cool down in order to achieve the

correct temperature for preparing an espresso.

• Appliance automatically cools down when

pressing the coffee button (one or two cups)

- When cooling down, the blue operating

control blinks and hot water flows into drip

tray. When correct temperature is reached,

appliance will run espresso cycle.

XP 4050_Europe.P65 28/01/05, 13:5617

• If your espresso machine runs short of

water, a sonor signal and all leds blinking

incite you to fill the water tank.

• Your espresso machine switches to stand by

mode after 30 mn for energy saving and

switches off after 1H 30 of none use.

Maintenance

- Never wash your espresso machine

accessories in the dishwasher.

After use, the water tank must be emptied.

. Drip tray

This must be emptied after using the

appliance after taking off the grid (19). If

several espressos are being prepared one after

the other, the drip tray should be emptied

from time to time (about once every 7 - 8

espressos). The presence of water is normal

and does not signify a leak. If necessary, clean

the drip tray and its grid with water and a

little non-abrasive washing-up liquid, rinse

and dry. Replace it correctly (20).

. The brewing head, the filter and the

filter holder

These must be cleaned after each use. All you

need to do is wipe a damp cloth over the

brewing head of your appliance and to wash

the other accessories in water and a little non-

abrasive washing-up liquid, rinse and dry.

If the brewing head is heavily clogged up,

unscrew the grid, clean it and refit it, pressing

down firmly (21).

When your espresso is not being used, do not

leave the filter holder on the appliance to

prevent wear on the gasket.

. The cup warming plate: remove this to

clean it with water and a little non-abrasive

washing-up liquid, rinse and dry.

. The auto cappuccino accessory

For more thorough cleaning the auto cappuc-

cino accessory can be dismantled from the

appliance.

Clean it with water, a little non-abrasive

washing-up liquid and a small brush. Rinse

and dry it before refitting it.

Please note the direction of fitting the flexible

tube : engage the straight-cut end in the auto

cappuccino Accessory.

Descaling

• Descaling of your espresso should be done

fairly frequently with citric or tartaric acid.

• Due to the acid substance, we recommend

protecting your your worktop and sink unit

during the descaling process, especially if it

is made of marble or stone. Isolate your

espresso with a tea towel, a tablecloth or a

tray.

However, we would advise you to use the

Krups descaling accessory, reference F054,

which is available from Krups after-sales

service centres. This accessory includes, apart

from two descaling doses, a testing strip for

water hardness to assess the frequency of

descaling of your appliance in normal use.

Descaling depends on the hardness of the

water, but also on the use cycle. The

frequency of descaling indicated by the F054

accessory is thus given by way of indication

only.

- Then follow the following method:

• Unscrew the grid from the head of the

appliance and clean it (21).

• Dissolve a sachet of KRUPS descaling

accessory, reference F054, in half a litre of

lukewarm water and pour the whole

amount into the empty water tank.

• start the appliance (4).

• Place a container, as large as possible,

beneath the auto cappuccino accessory.

• As soon as the blue operating control lamp

glows continuously, the appliance is ready

• Pressing the hot water button (15), run

through 1/3 of the liquid.

• Then, pressing the hot water button (15)

to stop.

• Move the container under the brewing

head.

• Run the second third of the liquid

immediately by pressing the coffee button

(10) as many times as necessary.

XP 4050_Europe.P65 28/01/05, 13:5618

• Stop the appliance by pressing the start/stop

switch (4) and wait for 10 - 15 minutes to

allow the descaler to take effect.

• Next, start the machine again (4) and allow

the rest of the liquid to run through by

pressing the coffee button (10) as

many times as necessary.

• Then rinse with two water tanks of fresh

water, clean the brewing head and replace

the grid on the head of the appliance (see

paragraph on maintenance).

• The guarantee does not include

espresso machines which do not

function, or do not function properly,

because descaling has not been carried

out.

Problems, probable causes and

how to correct them

Problems Probable causes Corrective actions

Espresso not hot Cups, filter and Preheat the

enough filter holder accessories (cups,

are cold. filter, filter holder)

See paragraph

«Preparing an

espresso».

Coffee leaks The filter holder See paragraph

around the filter is not mounted «Preparing an

holder correctly or has espresso».

not been tightened

sufficiently.

There are coffee Clean around the

grounds on the filter and the

edge of the filter gasket.

The brewing head Clean the gasket

gasket is dirty. with a damp cloth.

The brewing Contact an

head gasket approved Krups

is defective service centre.

Pump is very noisy No water in the Fill the water tank.

water tank.

Water tank incor- Press firmly down

rectly mounted. on the water tank.

Coffee grounds too Use fresh coffee

old or very dry and

the pump cannot

produce pressure.

Water does not run No water in the Fill the water tank.

through. water tank.

Water tank incor- Press firmly down

rectly mounted. on the water tank.

The filter is blocked, Clean the filter and

the coffee grounds the grid on the

are too fine or brewing head.

tamped down too See the paragraph

hard. «Maintenance»

and try a coarser

coffee.

Brewing head Put the grid to

grid is encrusted. soak in descaling

solution

See paragraph

«Maintenance».

Appliance needs See paragraph

descaling. «Descaling».

Water runs through Coffee grounds too Try a finer coffee

too quickly. coarse.

Quantity of Use the spoon

ground coffee provided to

is insufficient. measure out the

coffee.

Coffee grounds not Tamp down the

tamped down coffee again.

firmly enough.

The espresso has Coffee grounds Try a finer-ground

no crema (froth too coarse. coffe.

on coffee).

Coffee grounds Tamp down the

not tamped. coffee again.

Coffee grounds Use fresh coffee.

stale or too dry.

The milk is not very Auto Cappuccino See paragraph

frothy. accessory blocked «Maintenance»

Milk not fresh. Use fresh milk.

Milk is lukewarm. Put milk in

refrigerator.

Milk is not suitable. Try another brand.

Lots of water on Grounds not Tamp down the

the coffee grounds. properly tamped grounds.

down.

Insufficient quantity Increase the

of ground coffee. quantity of ground.

XP 4050_Europe.P65 28/01/05, 13:5619

If you have any product problems or queries,

please contact our Customer Relations Team

first for expert help and advice :

0845 602 1454 - UK

(01) 4751947 - Ireland

or consult our website - www.krups.co.uk

Recipes

Savour your espresso just as you like it: when

you want to relax or to round off a good

meal.

Here are a few recipes which you will be able

to create with your espresso machine.

. Original espresso

• Take one measuring spoonful of good

quality well roasted espresso coffee, and

filter it directly into the pre-heated cup.

If you use good, finely ground espresso coffee,

the cup will be crowned by a fine head of

froth.

• Add sugar if desired and treat yourself.

Original espresso is drunk without milk but

plenty of sugar.

. Cappuccino

For a state of the art cappuccino, the ideal

quantities are as follows: 1/3 coffee, 1/3 hot

milk, 1/3 frothy milk. The quantity of hot milk

+ froth obtained should be about double the

amount of coffee prepared.

• Use large cups which have been pre-heated.

• Fill them with coffee to the equivalent of one

cup of espresso and top up with milk which

has been frothed up using the auto cappuc-

cino accessory.

• Lastly, sprinkle with drinking chocolate

powder.

. Café crème

• Prepare a classic espresso in a large cup.

• Add a cloud of cream to make an espresso

with milk.

You can also replace the cream with hot milk.

. Caffe corretto *

• Prepare a cup of espresso in the normal way.

• Then slightly ‘correct’ the taste by adding

1/4 or 1/2 a glass of cognac.

You can also use anisette, grappa, Sambuco,

Kirsch or Cointreau for the same effect.

And there must be countless other possibilities

for «enriching» an espresso. Let your imagina-

tion run wild.

. Coffee Liqueur *

• Mix in an empty 0.75 litre bottle: 3 cups of

espresso, 250 g brown cane sugar, 1/2 litre

cognac or Kirsch.

• Leave the mixture to soak for at least 2

weeks.

You will then have a delicious liqueur,

especially for coffee lovers.

. Iced coffee à l’italienne

4 vanilla ice cubes, 2 cups of cold sugared

espresso, 1/8 litre milk, fresh cream, grated

chocolate.

• Mix the cold espresso with milk.

• Distribute the ice cubes among the glasses,

pour the coffee over them and decorate

with fresh cream and grated chocolate.

. Friesian coffee *

• Add a small glass of rum to a sugared cup of

espresso.

• Decorate with a good layer of fresh cream

and serve.

. Espresso flambé*

2 cups of espresso, 2 small glasses of cognac,

2 teaspoonfuls of brown sugar, fresh cream.

• Pour the cognac into heat-resistant glasses,

heat and flame.

• Add sugar, mix, pour the coffee and

decorate with fresh cream.

If you like, the espresso can also be diluted

with a little boiling water.

. Perfect espresso *

2 cups of espresso, 6 egg yolks, 200g sugar,

1/8 litre sugared fresh cream, 1 small glass of

orange liqueur.

• Beat the egg yolks with the sugar until it

forms a thick foamy mass.

XP 4050_Europe.P65 28/01/05, 13:5620

Environment protection first!

Your appliance contains valuable

materials which can be recovered or

recycled.

Leave it at a collection point.

• Add the cold espresso and orange liqueur.

• Then mix in the fresh whipped cream.

• Pour the mixture into cups or glasses.

• Put the cups into the freezer.

(* : The abuse of alcohol is dangerous to your

health).

XP 4050_Europe.P65 28/01/05, 13:5621

XP4050 EU11/Gr 0827 388

Krups Xp4050 Users Manual

Espresso Maker XP 4050 XP4050_eng

XP4050 to the manual 67d9b986-150e-426f-99c1-560091824ac0

Navigation menu

Versions of this User Manual:

Views

Navigation