LG ELECTRONICS LST230 Cellular CDMA WLL Terminal User Manual LST 230 2

LG Electronics, Inc. Cellular CDMA WLL Terminal LST 230 2

Users Manual

LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)2CDMA Fixed Wireless TerminalUser GuideModel: LST-230(F) & 2300(F)
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)3REVISED HISTORYDATE ISSUE CONTENTS OF CHANGES S/W VERSION2000.02ISSUE 1 Initial ReleasePlease read this manual before you use this product. This manual is based on the production version of LST-230(F)/2300(F) FWT. Software changes may have occurred after this printing.LGIC reserves the right to make changes in technical and product specifications without prior notice.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)4Blank Page
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)5Table of Contents1. Before You Start .....................................................................................................71.1 Safety Information .....................................................................................................................71.2 Optimal Phone Performance.....................................................................................................71.3 Care and Service.......................................................................................................................82. Introduction.............................................................................................................92.1 Front View of the Terminal.......................................................................................................102.2 3 LEDs Indicators .................................................................................................................... 11STEP I. Check Components .................................................................................................... 11STEP II. Place the Terminal .....................................................................................................12STEP III. Connect Components ...............................................................................................12STEP IV. Check LED indicators ...............................................................................................12STEP V. Install of Wall Mounting..............................................................................................122.3 Installation Steps .....................................................................................................................143. Basic Operation ....................................................................................................153.1 Power On.................................................................................................................................153.2 Placing a call ...........................................................................................................................153.3 Receiving a call .......................................................................................................................153.4 Ending a call............................................................................................................................153.5 Warning Tone after Remote Disconnect..................................................................................153.6 Dial Delay(Enblock mode only) ...............................................................................................153.7 Emergency Call(Enblock mode only) ......................................................................................164. System Features...................................................................................................174.1 Hook flash................................................................................................................................174.2 Dial Delay Time(Enblock mode only) ......................................................................................174.3 ROH (Receiver Off Hook)........................................................................................................174.4 Special Cellular Services.........................................................................................................174.5 Applications .............................................................................................................................185. Programming ........................................................................................................195.1 Speed Dial(Enblock mode only)..............................................................................................19Storing the Speed Dial Number ................................................................................................19Enable or Disable Speed Dial ...................................................................................................19Operation...................................................................................................................................205.2 Emergency Call(Enblock mode only) ......................................................................................20Entering the emergency phone number....................................................................................20Enable or Disable emergency call.............................................................................................205.3 Hot Line(Enblock mode only) ..................................................................................................20Programming the Hot Line number...........................................................................................20Enable the Hot Line Feature .....................................................................................................20Disable the Hot Line Feature.....................................................................................................21Programming the Hot Line Time ...............................................................................................215.4 Alarm(Enblock mode only) ......................................................................................................21Entering Alarm Time (12-hour Mode)........................................................................................21Entering Alarm Time (24-hour Mode)........................................................................................21Disable Alarm Feature...............................................................................................................215.5 Volume Level...........................................................................................................................22Changing the Volume Level ......................................................................................................225.6 Outgoing Call Lock(Enblock mode only) .................................................................................22Enable or Disable Outgoing Call Lock ......................................................................................22Changing Outgoing LOCK Code...............................................................................................225.7 G3 FAX Mode Setting..............................................................................................................22Enable or Disable G3 FAX mode ..............................................................................................23
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)66. Troubleshooting....................................................................................................247. General Information..............................................................................................257.1 LST-230(F) ..............................................................................................................................257.2 LST-2300(F) ............................................................................................................................26
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)711.. BBeeffoorree YYoouu SSttaarrtt1.1 Safety Information WarningTo reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not use thisproduct near swimming pools or other bodies of water.IMPORTANT Before installing or operating this product, read this information..1.2 Optimal Phone Performancel Do not operate your product when holding the antenna, or when someone is within four inches (tencentimeters) of the antenna. Holding the antenna affects call quality and may cause the telephone tooperate at a higher power level than needed.l For the best call quality, keep the antenna free from obstructions and point the antenna straight up.l Do not use the unit with a damaged antenna. Have your antenna replaced by a qualified technicianimmediately. Use only a manufacturer-approved antenna. Non-approved antennas, modifications, orattachments could impair call quality, damage the phone.l RF energy may affect improperly installed or inadequately shielded personal medical devices such aspace markers, hospital monitor. Consult the manufacturer of any personal medical devices to determine ifthey are adequately shielded from external RF energy. Turn your terminal OFF in health care facilitieswhen any regulations posted in the areas instruct you to do so. Hospitals or health care facilities may beusing equipment that could be sensitive to external RF energy.l If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interferenceby one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the radio or television and the telephone. -Connect the equipment into an outlet on a circuit different from that to which the terminal is connected. -Consult you Authorized LGIC Dealer of an experienced radio/TV technician for help.l Use only the battery, antenna and AC power supply provided by LGIC. Using any other type will invalidatethe warranty.l Only authorized personnel should service the phone and its accessories. Faulty installation or service anybe dangerous and may invalidate the warranty.l Do not use the unit in designated “no cellular phone use” area.l Avoid exposure to high temperature or humidity.l Avoid wetting the unit with any liquids. If the unit gets wet, turn the power off immediately and remove thebackup battery and AC power supply. If the unit is inoperable, then return to the service agent for service.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)8l Avoid shock or impact.l We recommend you to charge the backup battery before initial use. Backup battery may be dischargedduring delivery.1.3 Care and Servicel Unplug the Telephone from the wall outlet and remove antenna (or disconnect antenna cable) beforecleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.l If the unit fails for any reason, do not attempt to disassemble; contact the telephone service provider forassistance.l If any of the following conditions exist: Unplug the unit at the wall plug, remove battery, and call theservice provider. -The power supply cord is damaged or frayed. -Liquid has been spilled into the unit. -The unit has been exposed to rain or water. -The unit has been dropped or damaged. - The unit does not work normally by following the operating instructions. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)922.. IInnttrroodduuccttiioonnCongratulations on your purchase of the LGIC Fixed Wireless Terminal that has been designed to operate onthe latest digital mobile communications technology, Code Division Multiple Access (CDMA). This CDMA digitaltechnology has greatly enhanced voice clarity and can provide various advanced features. The terminal enablesthe normal operation and direct connection of standard telephone equipment into the cellular network.The standard unit provides:l Dial tone;l Touch tone (DTMF) or Pulse Dialing;l Support Caller ID Telephone;l Voice-Mail Notification ring-alerts you to new voice-mail messages;l Ring voltage used to ring the telephone connected to the unit, with a Ringer Equivalence Number of 4;l A phone jack to plug in the telephone equipment (RJ-11 Port);l A phone jack to plug in the G3 FAX equipment (RJ-11 Port);l DB9 Data Port for service and repairl AC Power supply with barrel plug connector;l Three lights (LEDs) to indicate the status of the unit;l Dipole Antenna;The LGIC Fixed Wireless Terminal can operate differently according to the system provider in thedialing manner. The first one is the “Enblock” mode and the second one is the “Overlap” mode. Pleasecontact your service provider in which mode the LGIC Fixed Wireless Terminal is working.Some features can not be supported by service provider’s policy and dialing method.For instance, the following features may not be supported in Overlap dialing mode;- Dial Delay and Dial Delay Time- Speed Dial- Emergency Call- Hot Line Call- Alarm- Outgoing Call LockOther features as determined by your service provider.Note: Telephones with multiple terminating impedance should be set for 600ohms.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)102.1 Front View of the Terminal< Figure 1 >ITEM DESCRIPTION LEDs Indicate the status of the unit DC-12V AC Power Adapter Phone/FAX (RJ-11 Jack) Connecting Port for Single Line Telephone or G3 FAXMachine Phone/FAX (RJ-11 Jack) Connecting Port for Single Line Telephone or G3 FAXMachine RS-232C DB 9 Connector Connecting Port for Data Service to PC TNC Antenna Connector Connecting Port for TNC Antenna
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)112.2 3 LEDs IndicatorsLED COLOR Operating ConditionGREEN-solid DC Power is appliedORANGE-solid Battery Power is appliedPOWER LEDRED-solid Low BatteryGREEN-solid Good SignalORANGE-solid Poor SignalSIGNAL LEDRED-solid No Service AreaGREEN – blink(0.5sec On / 0.5sec Off) Voice Message is receivedGREEN – blink(1 sec On / 1 sec Off) Data Service or G3 Fax Service is workingMODE LEDGREEN-solid G3 FAX receive mode is enabled2.3 InstallationYou should follow each step carefully as shown below in order to guarantee proper operation of CDMA FixedWireless Telephone.STEP I. Check Componentsl Fixed Wireless Terminal is supplied with the following standard unit and accessories;1. LST-230(F)/2300(F) Main Unit -1 EA-2. Dipole Antenna -1 EA-3. Backup Battery -1 EA-4. User Guide .-1 EA-5. AC/DC Power Adapter -1 EA-6. Power Cord -1 EA-l Please make sure that these components are present and check for evidence of shipping before you beginthe unit installation. If components are missing or damage is found, contact your authorized LGIC distributorimmediately.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)12 STEP II. Place the Terminall Place the terminal on the stable flat secure surface area (desk, table, etc.). Avoid direct exposure to the sunlights and damp area.l Read the Safety Information located at the first part of this document before you place the terminal. STEP III. Connect Componentsl Connect the antenna to the TNC connector located at the topside of the terminal. (See Figure 1 to locatethe TNC connector.) If you placed the terminal on the flat surface, bend the antenna up right.l Connect your phone cord to the RJ-11C port located at the left side of the terminal.l Connect the battery cable to the DC battery connector at the back of the main unit.l Connect the AC power supply cable to the DC input port located at the right side of the terminal.l If you use Data Service or PC FAX Service, connect your RS-232C cable cord to the DB9 port located atthe right side of the terminal.l If you use G3 FAX machine, connect your line cord of G3 FAX to the RJ-11 port located at the right side ofthe phone port. “ Refer to Connection Diagram with external equipment in Figure 2 “ STEP IV. Check LED indicatorsl When you followed the installation instruction STEP I to STEP III, please check the LEDs for normaloperation. When DC power is fed at the first time, LEDs will operate as follows:1. After few seconds, if receiving signal strength is strong enough, then SIGNAL LED is GREEN, if not, itis ORANGE or RED. And MODE LED is turned off. Power LED is GREEN if AC/DC power is applied. STEP V. Install of Wall Mountingl To mount terminal on the wall, please follow the procedure to install it correctly.1. Determine suitable location to mount terminal with mounting template;2. Mark the two openings and select round or panhead type screw;3. Drill out the holes with drill bit smaller in diameter than the screws4. Secure two screws into the wall, leaving about 1/8inch gap between the screw heads and the wall;5. Insert the DC power pack into an electrical outlet and attach the telephone line into the Phone Jack (RJ-11) of the unit.6. Place the terminal over the two screws so that the screw head protrudes out of the opening;7. Slide the terminal downward until the screw head is locked at the top of the opening and the terminal issecure;8. Tighten the screws the terminal is resting upon;
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)13[LST-230F] * Note : - G3 Fax can not connected to your LST-230 terminal. - Length between LST-230(F) and Telephone : over 1m. The adapter type(with power cord) may be different by country adaptation.TELEPHONEG3 Analog FaxPC3< 1mRJ-11C RJ-11C
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)14[LST-2300F]* Note : - G3 Fax can not connected to your LST-2300 terminal. - Length between LST-2300(F) and Telephone : over 1m.< Figure 2. Connection Diagram with External Equipment >2.4 Installation StepsPlease follow the below procedure to install the unit properly.Connect theantenna to theTNC connector(Turn right).Bend theantenna up right.Connect your phoneCord.Connect the ACpower supply.2143TELEPHONEG3 Analog FaxPCRJ-11C RJ-11C
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)1533.. BBaassiicc OOppeerraattiioonn3.1 Power On1. The POWER LED indicates the presents status;1) Using AC Adapter : Solid Green2) Using internal battery : Solid ORANGE3) Using internal battery and battery is week : Solid Red2. If the radio service is not available or radio signal is too weak to detect; The SIGNAL LED is Red. (No Service status) 3. When the phone is succeeded in getting the service, SIGNAL LED indicates the strength of the signal.1) Lifting handset, dial tone is heard and you can enter a phone number. (Not entering any key for 15 seconds (In the overlap dial mode, it may take over 15 seconds.) warningtone will be produced)*) If Hot Line function is enabled, busy tone is not produced and hot line number is automaticallyconnected.*) While having maintenance request order or lock order from the main system, neither dial tone nor busytone is produced. Instead of them, the lock tone(“pi-pi-pi”) will be heard one time and there will be nosound and both of MODE LED and POWER LED will be blinking with GREEN color simultaneously.3.2 Placing a callWhen lifting handset of the connected phone ("off hook"), the terminal determines whether cellular service isavailable. If it is available, dial tone is produced and a number can be dialed normally. If phone service is notavailable, SIGNAL LED of the terminal will be red and no dial tone will be heard.3.3 Receiving a callThe connected telephone rings when an incoming call is detected. Pick up the handset and begin talking.3.4 Ending a callWhen you have completed the call, place the handset back on hook. Also you can hook flash more than about 1second to end a call and place a new call without hanging up the handset.3.5 Warning Tone after Remote DisconnectA warning tone may be heard in the telephone after a remote party hangs up from a call, allowing another call tobe initiated after hook-flash.3.6 Dial Delay(Enblock mode only)The terminal waits 5 seconds before transmitting the dialed telephone number into the cellular network.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)163.7 Emergency Call(Enblock mode only)When emergency call number is connected once, it will not be terminated unless the called party disconnectsthe call(Emergency Call Hold Service). Therefore even caller hangs up the phone, the line will be stillconnected, so if the caller picks up the phone again, he can continue talking. If emergency call is connected,cellular service is not supported.As long as your telephone is registered on a system, you can place a call to emergency number including 911-even if your telephone is locked* or restricted*.Please check the available emergency call number with your service provider.*) “Transmit Lock” or “Transmit Restrict” features have a meaning only in “Enblock” mode.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)1744.. SSyysstteemm FFeeaattuurreess4.1 Hook flashWhen the terminal receives a hook-flash from the connected telephone device, it will automatically allow:1. For producing dial tone again after a phone number has been dialed without connection.2. The use of special cellular services which may be available in your cellular service area.Note: Hook-flash is accomplished in a call through either pressing the dedicated hook-flash key which isavailable on some phones or through a rapid single press of the hang-up mechanism upon which thehandset rests when the phone is hung up.4.2 Dial Delay Time(Enblock mode only)When placing a call, the phone number is sent over the network after last digit is dialed. In order to insureadequate time for dialing the last digit, a delay of 5 seconds is programmed into the terminal.4.3 ROH (Receiver Off Hook)If the telephone equipment remains “off-hook”, meaning that the handset is left off of its cradle as it would bewhen you hang up, with no dialing activity for about 45 seconds, a ROH tone emits from the receiver for aperiod of 60 seconds.(In the overlap dial mode, above “45 seconds” or “60 seconds” may be different accordingto the system.)( This feature may be available or not by country specification.)4.4 Special Cellular ServicesMany cellular systems offer special services such as call waiting, call forwarding, etc. You can purchase theseservices from your cellular service provider. There are certain dialing sequences to be entered, which vary fromservice provider to service provider. The service provider will provide the dialing instructions for your system.Call Forwarding – An incoming call can be delivered to another telephone number programmed. Pleasecontact your cellular service provider to use this feature.Call Waiting – You can receive another incoming call during a call. In this case, you will hear beep tone andthen you can connect the second call holding the first call by entering a code required by cellular serviceprovider. Your cellular service provider may require hook-flash (a quick, simulated "hang up") to answer thewaiting call. Other providers may require entering the codes involving digits 1-9, *, and # to answer a waitingcall.Three-way Conference Calls - For three-way conference calls, a hook-flash transmits the SEND command.Please contact your cellular service provider for more information on using this service.F Example1 Dial the first number and wait until connected;2 When connected, give hook-flash and dial the second number and give one more hook-flash to be connected;
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)183 When the second call is connected, give hook flash to complete a 3-way conference call.Voice Mail – Use voice mail service in the same manner as you would on a regular telephone. If your have anew voice-mail message, the WLL-terminal transmits a special Voice-Mail Notification Ring (1sec On / 6sec Offdefault) and Mode LED is blinking (0.5sec On/0.5sec Off). Please contact your cellular service provider for moreinformation on using Voice Mail or to change Voice-Mail Ring pattern.Caller ID – LST-230(F)/2300(F) can support Caller ID service if you have a telephone with Caller ID feature.Please contact your cellular service provider for more information on using this service.4.5 ApplicationsData Communication - LST-230(F)/2300(F) is capable of transmitting and receiving IS-707 Fax or modemcommunications. For data communications, you will need a data communication kit and a PC Fax softwarediskette where needed. For further information, please contact our authorized service dealer.Multi-extension Installations - For a multi-extension installation, make sure that all the extensions are on-hook. If one extension is off-hook (not hung up), none of the extensions on that line will ring when a call is beingreceived.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)1955.. PPrrooggrraammmmiinnggLST-230(F)/2300(F) provides various convenient and various features to user. This chapter describes how toprogram these features and to use them. The followings are main features can be used;Speed Dial(Enblock mode only)Emergency Call(Enblock mode only)Hot Line Call(Enblock mode only)Wake-up Alarm(Enblock mode only)Conversation Voice LevelOutgoing Call Lock(Enblock mode only)n Programming Instruction1. Lift Handset and press “#” key twice.2. Enter the field number (1 ~ 6) and you will hear the Menu Entering tone.3. Press “#” key and you will hear confirmation tone.4. Enter sub-fields and their options.5. Press “*” key to save and you will hear confirmation tone.5.1 Speed Dial(Enblock mode only)LST-230(F)/2300(F) has 30 memory locations (1~30:1 or 2 digits) to store frequently used phone numbers andyou can make a call by pressing memory location number only when the speed dial feature is enabled.Storing the Speed Dial Number1. Press “#” + “#” + “1” continuously to enter speed dial programming mode.2. Press “#” and one of memory numbers (1~30).3. Press “#” and the phone number (Max. 32 digits).4. Press “*” to store.Enable or Disable Speed Dial1. Press “#” + “#” + “1” continuously to enter speed dial programming mode.2. Press “#” and “1” or “2” to enable or disable respectively. “1” – Speed Dial Enable “2” – Speed Dial Disable3. Press “*” to store.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)20Operation1. Make a speed dial function enable.2. Lift handset and dial tone will be heard.3. Press speed dial number and wait for dial timeout(5 seconds).5.2 Emergency Call(Enblock mode only)LST-230(F)/2300(F) has 3 emergency call numbers (1~3) and max. 32 digits can be stored in each emergencycall number.Entering the emergency phone number1. Press “#”+”#”+”2” continuously to enter emergency call programming mode.2. Press “#” and one of the emergency memory location numbers (1~3).3. Press “#” and the phone number (Max. 32 digits).4. Press “*” to save and enable this function.Enable or Disable emergency call1. Press “#”+”#”+”2” continuously to enter emergency call programming mode.2. Press “#” and Enable code (“1”) or Disable code (“2”).3. Press “*” to save.If Emergency Call is disabled and Emergency Call number has been already programmed, you canmake enable Emergency Call by pressing “#’+”#”+”2”+”#” + ”1”+”*” without entering a emergency callnumber again.5.3 Hot Line(Enblock mode only)While the Hot line function is enabled, the programmed number will be automatically dialed when you pick upthe handset and wait for the programmed hot line time (1~10sec) without any key press.Programming the Hot Line number1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line Enable code “1”.3. Press “#” and Hot Line phone number (Max. 32 digits).4. Press “*” to save and enable this function.Enable the Hot Line Feature1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line Enable code “1”.3. Press “*” to save.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)21Disable the Hot Line Feature1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line Disable code “2”.3. Press “*” to save.Programming the Hot Line Time1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line time code “3”.3. Press “#” and enter desired Hot Line time (1~10 seconds).4. Press “*” to save.If Hot Line is disabled and Hot Line number has been already programmed, you can make enable HotLine feature by pressing “#’+”#”+”3”+”#”+”1”+”*” without entering a Hot Line Number again.5.4 Alarm(Enblock mode only)If alarm feature is enabled, you will hear ring at the programmed alarm time every day for 1 minute.Entering Alarm Time (12-hour Mode)1. Press “#”+”#”+”4” continuously to enter alarm time programming mode.2. Press “#” and alarm time code “1” for 12-hour mode.3. Press “#” and alarm time (HHMM +am(“1”) / pm(“2”)).4. In the forenoon, time range is 0000~1159.5. In the afternoon, time range is 1230~1259 or 0100 ~1159.6. Press “*” to save and enable Alarm Time.Entering Alarm Time (24-hour Mode)1. Press “#”+”#”+”4” continuously to enter alarm time programming mode.2. Press “#” and alarm time code “2” for 24-hour mode.3. Press “#” and alarm time (HHMM). (0000~2359)4. Press “*” to save and enable Alarm Time.Disable Alarm Feature1. Press “#”+”#”+”4” continuously to enter alarm time programming mode.2. Press “#” and alarm disable code “2”.3. Press “*” to save.If Alarm is disabled and time has been already programmed, you can make enable Alarm feature bypressing “#’+”#”+”4”+”#”+”1”+”*” without entering alarm time again.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)225.5 Volume LevelThere are three voice volume levels to be controlled by software, and you can set the level to the adequateconversation volume.Changing the Volume Level1. Press “#”+”#”+”5” continuously to enter Volume Level programming mode.2. Press “#” and Volume Level (1~3), then the confirm tone will be heard with the volume level changed. “1” – LOW Level “2” – MIDDLE Level “3” – HIGH Level3. Press “*” to save.Before pressing “*”, you can enter volume level continuously.5.6 Outgoing Call Lock(Enblock mode only)If you try to make an outgoing call while outgoing call lock is enabled, then you will hear warning tone after dialtime-out as a indication of entering the LOCK code. You should enter LOCK code to make an outgoing call.LOCK code is composed of 4 digits and the initial setting is “0000”. Outgoing Call Lock feature is disabled as afactory setting.Enable or Disable Outgoing Call Lock1. Press “#”+”#”+”6”+LOCK code continuously to enter Outgoing Call Lock programming mode.2. Press “#” and Enable (“1”) or Disable (“2”) code.3. Press “*” to save.Changing Outgoing LOCK Code1. Press “#”+”#”+”6”+LOCK code continuously to enter Outgoing Call Lock programming mode.2. Press “#” and “3” to change LOCK code.3. Press “#” and 4 digits of new LOCK code.4. Press “#” and re-enter new LOCK code.5. Press “*” to save.5.7 G3 FAX Mode SettingTo activate a Data Fax call by G3 FAX connected to your LST-230F/2300F terminal from the other devices(Land or Mobile Data Fax), your service provider should support wireless data FAX. And the LST-230F/2300Fmode should be changed to G3 FAX mode to change data path from RS-232C to G3 FAX machine. Becausethe terminal doesn’t recognize the call is for FAX or voice before being response. Following is the procedure tochange data path and default data path is RS-232C data path.Once G3 Fax mode is set, if AC power is gone and turned on again, the saved G3 Fax mode value is restored.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)23Enable or Disable G3 FAX mode1. Press “#”+”#”+”7” continuously to enter G3 FAX programming mode.2. Press “#” and Enable (“1”) or Disable (“2”) code. Enable means that Data call path is changed to G3 FAX. Disable means that Data call path is changed to RS-232C. (Default mode)3. Press “*” to save.Note 1. Sending or receiving some documents by G3 FAX is possible only in AC power mode. If AC power isgone, you can not use the G3 Fax machine connected to the LST-230F/2300F.Note 2. The recommended usage for this G3 Fax Mode is like this;1. Disable G3 Fax Mode for normal usage.- You can make a voice call using the telephone device connected to the “Tel/Fax” jack of the LST-230F/2300F.- You can fax a document using the G3 Fax machine connected to the “Tel/Fax” jack of the LST-230F/2300F.2. To receive or send a document by fax, should be set G3 Fax Mode. After receiving the faxdocument, disable G3 Fax Mode for another voice call.3. If you want to use the LST-230F/2300F terminal only for G3 Fax sending or receiving other than thevoice call, then keep the terminal in G3 Fax Mode enabled state
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)2466.. TTrroouubblleesshhoooottiinnggIn the event you are unable to place or receive telephone calls, first check the appropriate power indication onthe LED. In case of no power, check the wiring connections between the power outlet and the terminal. Checkfor the appropriate service indication on the LED. If an adequate signal is not present, try different locations forthe better signal reception.This will verify the condition of the telephone equipment and the internal wiring of the telephone service to veritythat it is working properly. If the telephone system of wiring is not working properly, replace or repair theequipment as required. The unit will not function with equipment that requires data transmission.Contact your service provider if either of the following condition is true:l The terminal does not work and the LED indicates “No Service” and if changing the locations does notresolve the problem.l The terminal does not work and the LED indicates “In Service”.l Power Supply – If the unit does not respond once plugged into a power supply;² Check that the AC power source.² Check that the Barrel Plug of the Power Supply is properly inserted into the terminal.² Check that the terminal Power Supply is properly plugged into the electrical outlet or powersource.Warning! Only Authorized Service Personnel should remove the cover of the fixed wireless terminal foradditional service. The contents of the terminal contain components that present an Electric ShockHazard if handled improperly.For further assistance, contact your Authorized LGIC Distributor for service and assistance.Please keep your Model number and Serial number ready for quicker service.
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)2577.. GGeenneerraall IInnffoorrmmaattiioonn7.1 LST-230(F) Main UnitItem DescriptionTx Frequency Digital : 824 ~ 849 MHzRx Frequency Digital : 869 ~ 894 MHzChannel Bandwidth 1.25 MHzFrequency Stability Digital : ±300 HzTx Power Digital : Max. 0.268WRx Power Level -104 ~ -25 dBmSize 198 x 198 x 53 mmWeight(g) 710g ( w/o battery ) / 990g ( w/ battery ) AC/DC AdapterItem DescriptionInput Voltage 100V ~ 250V ACInput Current 0.6A Max.Input Frequency 50 / 60 HzOutput Voltage 12V(DC) / 2A Internal Back-up BatteryItem DescriptionCapacity 8.4V NiMHTalk duration time 2 HoursStandby duration time 24 HoursCharging duration time Trickle, 24 Hours
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)267.2 LST-2300(F) Main UnitItem DescriptionTx Frequency Digital : 1850 ~ 1910 MHzRx Frequency Digital : 1930 ~ 1990 MHzChannel Bandwidth 1.25 MHzFrequency Stability Digital : ±150 HzTx Power Digital : Max. 0.266WRx Power Level -104 ~ -25 dBmSize 198 x 198 x 53 mmWeight(g) 710g ( w/o battery ) / 990g ( w/ battery ) AC/DC AdapterItem DescriptionInput Voltage 100V ~ 250V ACInput Current 0.6A Max.Input Frequency 50 / 60 HzOutput Voltage 12V(DC) / 2A Internal Back-up BatteryItem DescriptionCapacity 8.4V NiMHTalk duration time 2 HoursStandby duration time 24 HoursCharging duration time Trickle, 24 Hours
LGIC CDMA Fixed Wireless TerminalLST-230(F) / 2300(F)27Licensed by QUALCOMM Incorporated under one or more of the following Patents:U.S, Patent No. 4,901,307 U.S, Patent No. 5,056,109 U.S, Patent No. 5,099,204U.S, Patent No. 5,101,501 U.S, Patent No. 5,103,459 U.S, Patent No. 5,107,225

Navigation menu