Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) User Idea Centre K315 Desktop (ideacentre) Type 10079

Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) ハードウエアメンテナンスマニュアル - Lenovo IdeaCentre K3 シリーズ K330 Desktop (ideacentre) - Type 7727 Lenovo IdeaCentre K3 Series Hardware Maintenance Manual (English)

Lenovo Ideacentre K330B Hardware Maintenance Manual (English) Lenovo IdeaCentre K330B Hardware Maintenance Manual K330B Desktop (ideacentre) - Type 10066 Lenovo IdeaCentre K330B Hardware Maintenance Manual (English)

2011-11-29

User Manual: Lenovo Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) Lenovo IdeaCentre K3 Series Hardware Maintenance Manual K315 Desktop (ideacentre) - Type 10079

Open the PDF directly: View PDF .
Page Count: 57

Download
Open PDF In Browser	View PDF

Contents

Chapter 1. About this manual................................................. 1
Important Safety Information....................................................................... 1
Using eSupport..................................................................................................... 2
Important information about replacing RoHS compliant FRUs... 2

Chapter 2. Safety information................................................. 4
General safety........................................................................................................ 4
Electrical safety..................................................................................................... 5
Safety inspection guide.................................................................................... 7
Handling electrostatic discharge-sensitive devices .......................... 8
Grounding requirements . .............................................................................. 8
Safety notices......................................................................................................... 9

Chapter 3. General information............................................12
Specifications...................................................................................................... 12

Chapter 4. General Checkout................................................13
Problem determination tips ....................................................................... 14

Chapter 5. Using the Setup Utility (Type G43)..................16
Starting the Setup Utility program.......................................................... 16
Viewing and changing settings................................................................. 16
Using passwords............................................................................................... 17
Using Device....................................................................................................... 19
Selecting a startup device............................................................................ 20
Exiting from the Setup Utility program................................................. 21

Hardware Maintenance Manual

Chapter 6. Symptom-to-FRU Index.....................................22
Hard disk drive boot error............................................................................ 22
Power Supply Problems................................................................................. 23
Beep symptoms ............................................................................................... 24
POST error codes.............................................................................................. 25
Undetermined problems.............................................................................. 27

Chapter 7. Replacing hardware............................................28
General information........................................................................................ 28
Removing the computer cover . ............................................................... 29
Removing the front bezel............................................................................. 30
Replacing a memory module .................................................................... 31
Replacing the hard disk drive..................................................................... 33
Replacing an optical drive............................................................................ 34
Replacing the system fan assembly......................................................... 35
Replacing the heat sink assembly ........................................................... 38
Replacing a PCI or AGP adapter ............................................................... 39
Replacing the CPU............................................................................................ 45
Replacing the keyboard ............................................................................... 49
Replacing the mouse ..................................................................................... 49
Replacing the External speaker ................................................................ 50
Completing the installation ....................................................................... 51

Chapter 8. Additional Service Information(Type G43)...53
Power management ...................................................................................... 53

Appendix. Statement..............................................................54

Chapter 1. About this manual

About this manual

This manual contains service and reference information for Lenovo
IdeaCentre K computers listed on the cover. It is intended only for trained
servicers who are familiar with Lenovo computer products.
Before servicing a Lenovo product, be sure to read the Safety Information.
This manual includes a complete FRU part number listing for each
machine type and model listed on the cover. If you have internet access,
FRU part numbers are also available at: http:/www.lenovo.com/support.
The description of the TV card in this manual is only used for the machines
which have the TV card. It is invalid for those machines which do not have
TV card.

Important Safety Information
Be sure to read all caution and danger statements in this book before
performing any of the instructions.
Veuillez lire toutes les consignes de type DANGER et ATTENTION du
présent document avant d’exécuter les instructions.
Lesen Sie unbedingt alle Hinweise vom Typ “ACHTUNG” oder “VORSICHT”
in dieser Dokumentation, bevor Sie irgendwelche Vorgänge durchführen
Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel
manuale prima di eseguire una qualsiasi delle istruzioni
Certifique-se de ler todas as instruções de cuidado e perigo neste manual
antes de executar qualquer uma das instruções
Es importante que lea todas las declaraciones de precaución y de peligro
de este manual antes de seguir las instrucciones.
执行任何说明之前，请确保已阅读本书中的所有警告和危险声明。

Hardware Maintenance Manual

Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
•• eSupport can be used to view the list of key commodities built in a
particular machine serial.
•• eSupport can be accessed at the following Web site:
http://www.lenovo.com/support
•• To view the key commodities:
1. Click Parts information.
2. Under Parts information, click Parts lookup.
3. Under Parts lookup, type the model type and serial number; then
click Continue.
The key commodities are returned in the eSupport record under
Parts shipped with your system.
For the remaining FRUs (the complete list of FRUs at the MT Model level)
•• eSupport can be used to view the complete list of FRUs for a machine
type and model.
•• To view the complete list of FRUs for a machine type:
1. Point your browser to http://www.lenovo.com/support.
2. Type the machine type (Example: 8129) in the Use Quick Path field;
then click Go.
3. Under Browse by product, click Continue.
4. Under Important information, click Parts information.
5. In the Refine results field, select Service parts; then click the entry for
your machine type.
The list of service parts by description, with applicable machine type
model and FRU part number is displayed.

Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and
Electronic Equipment Directive (2002/95/EC) is a European Union
legal requirement affecting the global electronics industry. RoHS
requirements must be implemented on Lenovo products placed on the
market after June 2006. Products on the market before June 2006 are
not required to have RoHS compliant parts.
So, if the parts are not compliant originally, replacement parts can
also be noncompliant, but in all cases, if the parts are compliant, the
replacement parts must also be compliant.
Lenovo plans to transition to RoHS compliance well before the

Chapter 1. About this manual

implementation date and expects its suppliers to be ready to support
Lenovo’s requirements and schedule. Products sold in 2005, will contain
some RoHS compliant FRUs. The following statement pertains to these
products and any product Lenovo produces containing RoHS compliant
parts.
RoHS compliant Lenovo IdeaCentre K parts have unique FRU part
numbers. Before or after June, 2006, failed RoHS compliant parts must
always be replaced using RoHS compliant FRUs, so only the FRUs
identified as compliant in the system HMM or direct substitutions for
those FRUs can be used.
Products marketed before June 2006 Products marketed after June 2006
Current or
Replacement
Current or
Replacement
original part
FRU
original part
FRU
Non-RoHS
Can be Non-RoHS Must be RoHS
Must be RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that
is automatically shipped by the distribution center at the time of
order.
Related Web URLs are:
•• Lenovo information for Suppliers website:
http://www-03.ibm.com/procurement/proweb.nsf/
ContentDocsByTitle/United+States~Information+for+suppliers
•• RoHS Directive:
http://europa.eu.int/eur-lex/pri/en/oj/dat/2003/l_037/
l_03720030213en00190023.pdf
•• California Senate Bills 20, 50:
http://www.ciwmb.ca.gov/HHW/Events/AnnualConf/2004/
presentation/MPaparian.pdf

Hardware Maintenance Manual

Safety information

This chapter contains the safety information that you need to be familiar
with before servicing a computer.

General safety
Follow these rules to ensure general safety:
•• Observe good housekeeping in the area of the machines during and
after maintenance.
•• When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you
attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action
removes the strain from the muscles in your back. Do not attempt to
lift any objects that weigh more than 16 kg (35 lb) or objects that you
think are too heavy for you.
•• Do not perform any action that causes hazards to the customer, or that
makes the equipment unsafe.
•• Before you start the machine, ensure that other service representatives
and the customer’s personnel are not in a hazardous position.
•• Place removed covers and other parts in a safe place, away from all
personnel, while you are servicing the machine.
•• Keep your tool case away from walk areas so that other people will not
trip over it.
•• Do not wear loose clothing that can be trapped in the moving parts of a
machine. Ensure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
•• Insert the ends of your necktie or scarf inside clothing or fasten it with
a nonconductive clip, approximately 8 centimeters (3 inches) from the
end.
•• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners
for your clothing.
Remember: Metal objects are good electrical conductors.

Chapter 2. Safety information

•• Wear safety glasses when you are: hammering, drilling soldering,
cutting wire, attaching springs, using solvents, or working in any other
conditions that might be hazardous to your eyes.
•• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
•• Reinstall all covers correctly before returning the machine to the
customer.

Electrical safety

CAUTION:
Electrical current from power, telephone, and communication cables
can be hazardous. To avoid personal injury or equipment damage,
disconnect the attached power cords, telecommunication systems,
networks, and modems before you open the server/workstation covers,
unless instructed otherwise in the installation and configuration
procedures.
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand
tools have handles covered with a soft material that does not
insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats
that contain small conductive fibers to decrease electrostatic
discharges. Do not use this type of mat to protect yourself
from electrical shock.
•• Find the room emergency power-off (EPO) switch, disconnecting
switch, or electrical outlet. If an electrical accident occurs, you can then
operate the switch or unplug the power cord quickly.
•• Do not work alone under hazardous conditions or near equipment that
has hazardous voltages.
•• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
•• Before you start to work on the machine, unplug the power cord. If
you cannot unplug it, ask the customer to power-off the wall box
that supplies power to the machine and to lock the wall box in the off
position.

Hardware Maintenance Manual

•• If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is
near you.
Remember: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical
equipment; keep the other hand in your pocket or behind your back.
Remember: There must be a complete circuit to cause electrical
shock. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to
insulate you from grounds such as metal floor strips and machine
frames.
Observe the special safety precautions when you work with very
high voltages; these instructions are in the safety sections of
maintenance information. Use extreme care when measuring high
voltages.
•• Regularly inspect and maintain your electrical hand tools for safe
operational condition.
•• Do not use worn or broken tools and testers.
•• Never assume that power has been disconnected from a circuit. First,
check that it has been powered-off.
•• Always look carefully for possible hazards in your work area. Examples
of these hazards are moist floors, nongrounded power extension cables,
power surges, and missing safety grounds.
•• Do not touch live electrical circuits with the reflective surface of a
plastic dental mirror. The surface is conductive; such touching can
cause personal injury and machine damage.
•• Do not service the following parts with the power on when they are
removed from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
•• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.

Chapter 2. Safety information

Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially
unsafe conditions on these products. Each machine, as it was designed
and built, had required safety items installed to protect users and service
personnel from injury. This guide addresses only those items. However,
good judgment should be used to identify potential safety hazards due to
attachment of features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first
correcting the problem.
Consider these conditions and the safety hazards they present:
•• Electrical hazards, especially primary power (primary voltage on the
frame can cause serious or fatal electrical shock).
•• Explosive hazards, such as a damaged CRT face or bulging capacitor
•• Mechanical hazards, such as loose or missing hardware
The guide consists of a series of steps presented in a checklist. Begin the
checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to
measure third-wire ground continuity for 0.1 ohm or less between
the external ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the
parts listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious alterations. Use good judgment as to the safety
of any alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.

Hardware Maintenance Manual

Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs)
should be considered sensitive to electrostatic discharge (ESD). ESD
damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine,
the part, the work mat, and the person handling the part are all at the
same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the
requirements noted here.
2. Make sure that the ESD protective devices you use have been certified
(ISO 9000) as fully effective.
When handling ESD-sensitive parts:
•• Keep the parts in protective packages until they are inserted into the
product.
•• Avoid contact with other people.
•• Wear a grounded wrist strap against your skin to eliminate static on
your body.
•• Prevent the part from touching your clothing. Most clothing is insulative
and retains a charge even when you are wearing a wrist strap.
•• Use the black side of a grounded work mat to provide a static-free
work surface. The mat is especially useful when handling ESD-sensitive
devices.
•• Select a grounding system, such as those listed below, to provide
protection that meets the specific service requirement.
Note: The use of a grounding system is desirable but not required to
protect against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or
green-wire ground.
– Use an ESD common ground or reference point when working on a
double-insulated or battery-operated system. You can use coax or
connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated
computers.

Grounding requirements
Electrical grounding of the computer is required for operator safety and
correct system function. Proper grounding of the electrical outlet can be
verified by a certified electrician.

Chapter 2. Safety information

Safety notices
The caution and danger safety notices in this section are provided in the
the language of English.

DANGER
Electrical current from power, telephone and communication cables is
hazardous.
To avoid a shock hazard:
•• Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
•• Connect all power cords to a properly wired and grounded electrical
outlet.
•• Connect to properly wired outlets any equipment that will be
attached to this product.
•• When possible, use one hand only to connect or disconnect signal
cables.
•• Never turn on any equipment when there is evidence of fire, water, or
structural damage.
•• Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
•• Connect and disconnect cables as described in the following table
when installing, moving, or opening covers on this product or
attached devices.
To Connect
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to
connectors.
4. Attach power cords to outlet.
5. Turn device ON.

To Disconnect
1. Turn everything OFF.
2. First, remove power cords from
outlet.
3. Remove signal cables from
connectors.
4. Remove all cables from devices.

Hardware Maintenance Manual

CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or
an equivalent type battery recommended by the manufacturer. If your
system has a module containing a lithium battery, replace it only with
the same module type made by the same manufacturer. The battery
contains lithium and can explode if not properly used, handled, or
disposed of.
Do not:
•• Throw or immerse into water
•• Heat to more than 100°C (212°F)
•• Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.

CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic
devices, or transmitters) are installed, note the following:
•• Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
•• Use of controls or adjustments or performance of procedures other
than those specified herein might result in hazardous radiation
exposure.

DANGER:
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the
beam.

Chapter 2. Safety information

CAUTION:
Use safe practices when lifting.

CAUTION:
The power control button on the device and the power switch on the
power supply do not turn off the electrical current supplied to the
device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords
are disconnected from the power source.

2
1

CAUTION:
Do not place any object weighing more than 82 kg (180 lbs.) on top of
rack-mounted devices.

Hardware Maintenance Manual

General information

This chapter provides general information that applies to all machine
types supported by this publication.

Specifications
This section lists the physical specifications for your computer.

Type IdeaCentre K3
This section lists the physical specifications.
Dimensions
Width: 180 mm
Height: 388 mm
Length: 436.5 mm
Environment
Air temperature:
Operating: 10° to 35°C
Transit: -40° to 55°C
Humidity:
Operating: 35% to 80%
Transit: 20% to 93% (40°C)
Altitude: 86KPa to 106KPa
Electrical input
Input voltage: 220V±10% or 110V±10%
Input frequency: 50Hz ±1Hz

Chapter 4. General Checkout

General Checkout

Attention
The drives in the computer you are servicing might have been
rearranged or the drive startup sequence changed. Be extremely
careful during write operations such as copying, saving, or
formatting. Data or programs can be overwritten if you select an
incorrect drive.
General error messages appear if a problem or conflict is found by an
application program, the operating system, or both. For an explanation
of these messages, refer to the information supplied with that software
package.
Notes
• The default is for this computer to boot up in quiet mode (no beep,
no memory count and checkpoint code display) when no errors are
detected by POST.
• To enable beep, memory count, and checkpoint code display when
a successful POST occurs, do the following:
1. Start the Setup Utility program. See “Starting the Setup Utility
program”.
2. Select Start Options.
3. Set Power-On Self-Test to Enhanced.
• Before replacing any FRUs, ensure that the latest level of BIOS is
installed on the system. A down-level BIOS might cause false errors
and unnecessary replacement of the system board.
Use the following procedure to help determine the cause of the problem:
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Power-on all external devices.

Hardware Maintenance Manual

5. Power-on the computer.
• Look for displayed error codes
• Listen for beep codes
• Look for readable instructions or a main menu on the display.
If you did not receive the correct response, proceed to step 6.
If you do receive the correct response, proceed to step 7.
6. Look at the following conditions and follow the instructions:
• If you hear beep codes during POST, go to “Beep symptoms”.
• If the computer displays a POST error, go to “POST error codes”.
• If the computer hangs and no error is displayed, continue at step 7.
7. If you cannot continue, replace the last device tested.

Problem determination tips
Due to the variety of hardware and software combinations that can be
encountered, use the following information to assist you in problem
determination. If possible, have this information available when
requesting assistance from Service Support and Engineering functions.
•• Machine type and model
•• Processor or hard disk upgrades
•• Failure symptom
– Do diagnostics indicate a failure?
– What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
– If it has been working, what changes were made prior to it failing?
– Is this the original reported failure?
•• Diagnostics version
– Type and version level
•• Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
•• Operating system software
– Type and version level
Note: To eliminate confusion, identical systems are considered identical
only if they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same configuration options set in the system
7. Have the same setup for the operation system control files

Chapter 4. General Checkout

Comparing the configuration and software set-up between
“working and non-working” systems will often lead to problem
resolution.

Hardware Maintenance Manual

Using the Setup Utility
(Type G43)

The Setup Utility program is used to view and change the configuration
settings of your computer, regardless of which operating system you are
using. However, the operating-system settings might override any similar
settings in the Setup Utility program.

Starting the Setup Utility program
To start the Setup Utility program, do the following:
1. If your computer is already on when you start this procedure, shut
down the operating system and turn off the computer.
2. Press and hold the F1 key then turn on the computer. When you hear
multiple beeps, release the F1 key.
Notes:
a. If you are using a USB keyboard and the Setup Utility program does
not display using this method, repeatedly press and release the F1
key rather than leaving it pressed when turning on the computer.
b. If a power-on password or an administrator password has been set,
the Setup Utility program menu is not displayed until you type your
password. For more information, see “Using passwords.”
The Setup Utility might start automatically when POST detects that
hardware has been removed or new hardware has been installed in your
computer.

Viewing and changing settings
The Setup Utility program menu lists items that identify system
configuration topics. To view or change settings, see “Starting the Setup
Utility program.”
When working with the Setup Utility program menu, you must use the

Chapter 5. Using the Setup Utility

keyboard. The keys used to perform various tasks are displayed on the
right side of each screen.

Using passwords
By using the Setup Utility program, you can set passwords to prevent
unauthorized persons from gaining access to your computer and data.
See “Starting the Setup Utility program.” The following types of passwords
are available:
• Administrator Password
• Power-On Password
You do not have to set any passwords to use your computer. However, if
you decide to set any passwords, read the following sections.

Password considerations
A password can be any combination of up to 16 characters (a-z and
0-9) and symbols. For security reasons, it is a good idea to use a strong
password that cannot be easily compromised. We suggest the passwords
should adhere to the following rules:
• Must have at least seven characters in length
• Contain at least one alphabetic character, one numeric character.
• Setup Utility program and hard disk drive passwords are not case
sensitive
• Not be your name or your user name
• Not be a common word or a common name
• Be significantly different from your previous password

Administrator password
When a Administrator Password is set, it deters unauthorized persons from
changing configuration settings. If you are responsible for maintaining
the settings of several computers, you might want to set a Administrator
Password.
After you set a Administrator Password, a password prompt is displayed
each time you try to access the Setup Utility program.
If both the administrator and power-on passwords are set, you can type
either password. However, to change any configuration settings, you must
use your administrator password.

Hardware Maintenance Manual

Setting, changing, and deleting a Administrator password
To set, change, or delete a password, do the following:
Note: A password can be any combination of up to 16 characters (A- Z, a-z,
and 0-9). For more information, see “Password considerations” on
page 17.
1. Start the Setup Utility program (see “Starting the Setup Utility program”
on page 16).
2. From the Setup Utility program menu, select Security .
3. Select Set Administrator Password and press Enter.
4. The password dialog box will be displayed. Type the new password,
and press Enter.
5. when prompted to confirm the password, type the password again. If
you type the password correctly, the password will be installed.
To delete a previously set Administrator password, do the following :
Note: When prompted for a password, you must type your Administrator
password.
1. From the Setup Utility program menu, select Change Supervisor
Password and press Enter.
2. when you type the Administrator password. a message will display
that Enter New Password. Press Enter and a message will display
that indicates the password has been disabled. After that, the poweron password will be disabled too if a power-on password has been
installed.
3. Press any key to contine.

Power-on Password
When a Power-On Password is set, you cannot start the Setup Utility
program until a valid password is typed from the keyboard.
You should set a power-on password after you set the administrator
password. If you didn’t setup the administrator password but only set the
power-on password, you cannot change any configuration settings.

Setting, changing, and deleting a power-on password
To set, change, or delete a power-on password, do the following:
Note: A password can be any combination of up to 16 characters(A-Z, a-z,
and 0-9).
1. Start the Setup Utility program (See ”Starting the Setup Utility program”.)

Chapter 5. Using the Setup Utility

2.
3.
4.
5.

From the Setup Utility program menu, Select Security.
selet Change User Password and press Enter.
Select Set Power-On Password and press Enter.
when prompted to confirm the password, type the password again. If
you type the password correctly, the password will be installed.

To delete a previously set power-on password, do the following :
Note: When prompted for a password, you must type your administrator
password.
1. From the Setup Utility program menu, Select Security. select Set
Power-On Password and press Enter.
2. when you type the power-on password. a message will display that
Enter New Password. Press Enter and a message will display that
indicates the password has been disabled.
3. Press any key to contine.

Using Device
Device is used to enable or disable user access to the following device:
USB Setup

When this feature is set to Disable, the device
of USB Setup is disabled and will not be
displayed in the system configuration.

To set Device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program”
on page 16).
2. From the Setup Utility program menu, select Device.
3. Select USB Setup.
4. Select Disable or Enable and press Enter.
5. Return to the Setup Utility program menu and select Exit and then Save
changes and Exit.
Note: If you do not want to save the settings, select Discard Changes
and Exit or Discard Changes. You can set others such as , Serial
Port Setup, USB Setup, Video Setup, Audio Setup, Network
Setup and so on. See the information displayed on the right side
of the screen.

Hardware Maintenance Manual

Selecting a startup device
If your computer does not start up (boot) from a device such as the
CD-ROM, diskette, or hard disk as expected, use one of the following
procedures to select a startup device.

Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note: Not all CDs, hard disks, and diskettes are bootable.
1. Turn off your computer.
2. Press and hold the F12 key then turn on the computer. When the
Startup Device Menu appears, release the F12 key.
Note: If you are using a USB keyboard and the Startup Device Menu
does not display using this method, repeatedly press and release
the F12 key rather than leaving it pressed when turning on the
computer.
3. Select the desired startup device from the Startup Device Menu and
press Enter to begin.
Note: Selecting a startup device from the Startup Device menu does
not permanently change the startup sequence.

Selecting or changing the startup device sequence
To view or permanently change the configured startup device sequence,
do the following:
1.
2.
3.
4.

Start the Setup Utility program (see “Starting the Setup Utility program” ).
Select StartUp.
Select Primary Boot Sequence.
Select the devices for the 1st Boot Device, the 2nd Boot Device, the 3rd
Boot Deviece and the 4th Boot Device.
5. Press ESC to return the Primary Boot Sequence. and then Save changes
and Exit.
If you have changed these settings and want to return to the default
settings, select Load Optimal Defaults on the Setup Utility menu.

Chapter 5. Using the Setup Utility

Exiting from the Setup Utility program
When you finish viewing or changing settings, press Esc to return to the
Setup Utility program menu (you might have to press Esc several times).
If you want to save the new settings, select Save changes and Exit before
you exit. Otherwise, your changes will not be saved.

Hardware Maintenance Manual

Symptom-to-FRU Index

The Symptom-to-FRU index lists error symptoms and possible causes.
The most likely cause is listed first. Always begin with Chapter 4, “General
Checkout,” on page 13. This index can also be used to help you decide
which FRUs to have available when servicing a computer. If you are unable
to correct the problem using this index, go to “Undetermined problems”
on page 27.
Notes
• If you have both an error message and an incorrect audio response
diagnose the error message first.
• If you cannot run the diagnostic tests or you get a diagnostic error
code when running a test but did receive a POST error message
diagnose the POST error message first.
• If you did not receive any error message look for a description of
your error symptoms in the first part of this index.

Hard disk drive boot error
A hard disk drive boot error (error codes 1962 and I999030X) can have the
following causes.
Error

FRU/Action

The start-up drive is not in the boot Check the configuration and ensure
sequence in configuration.
the start-up drive is in the boot
sequence.
No operating system installed on
the boot drive.

Install an operating system on the
boot drive.

Chapter 6. Symptom-to-FRU Index

Error

FRU/Action

The boot sector on the start-up
drive is corrupted.

The drive must be formatted do the
following:
1. Attempt to back-up the data on
the failing hard disk drive.
2. Using the operating systems
programs format the hard disk
drive.

The drive is defective.

Replace the hard disk drive.

Power Supply Problems
If you suspect a power problem, use the following procedures.
Check/Verify
FRU/Action
Reseat connectors
Check the following for proper
installation.
•• Power Cord
•• On/Off Switch connector
•• On/Off Switch Power Supply
connector
•• System Board Power Supply
connectors
•• Microprocessor(s) connection
Check the power cord for continuity. Power Cord
Check the power-on switch for
Power-on Switch
continuity.

Hardware Maintenance Manual

Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses
(intervals without sound) during POST.
The following tables describes beep symptoms.
Beep Symptom
1 beep
Memory refresh timer error

FRU/Action
Reseat the memory, or replace with
known good modules.

2 beeps
Parity error in base memory (first
64KB block)
3 beeps
Base memory read/write test error
4 beeps
Fatal error indicating a serious
Motherboard timer not operational problem with the system. Consult
your system manufacturer. Before
declaring the motherboard beyond
all hope, eliminate the possibility
5 beeps
of interference by a malfunctioning
Processor error
add-in card. Remove all expansion
cards except the video adapter.
• If beep codes are generated
when all other expansion cards
6 beeps
are absent, consult your system
8042 Gate A20 test error (cannot
manufacturer’s technical support.
switch to protected mode)
• If beep codes are not generated
when all other expansion cards
are absent, one of the add-in cards
7 beeps
is causing the malfunction. Insert
General exception error (processor
the cards back into the system
exception interrupt error)
one at a time until the problem
happens again. This will reveal the
malfunctioning card.
8 beeps
If the system video adapter is an
Display memory error (system video add-in card, replace or reseat the
adapter)
video adapter. If the video adapter
is an integrated part of the system
board, the board may be faulty.

Chapter 6. Symptom-to-FRU Index

Beep Symptom
9 beeps
AMIBIOS ROM checksum error

FRU/Action
Fatal error indicating a serious
problem with the system. Consult
your system manufacturer. Before
declaring the motherboard beyond
all hope, eliminate the possibility
of interference by a malfunctioning
add-in card. Remove all expansion
10 beeps
cards except the video adapter.
CMOS shutdown register read/write
• If beep codes are generated
error
when all other expansion cards
are absent, consult your system
manufacturer’s technical support.
• If beep codes are not generated
when all other expansion cards
11 beeps
are absent, one of the add-in cards
Cache memory test failed
is causing the malfunction. Insert
the cards back into the system
one at a time until the problem
happens again. This will reveal the
malfunctioning card.

POST error codes
Each time you power-on the system, it performs a series of tests that
check the operation of the system and some options. This series of tests is
called the Power-On Self-Test, or POST. POST does the following operations.
•
•
•
•

Checks some basic system-board operations
Checks the memory operation
Starts the video operation
Verifies that the boot drive is working

If the POST detects a problem, an error message appears on the screen.
A single problem can cause several error messages to appear. When you
correct the cause of the first error message, the other error messages
probably will not appear on the screen the next time you turn on the
system.

Hardware Maintenance Manual

POST Error Message
CMOS Date/Time Not Set

CMOS Battery Low

CMOS Checksum Bad

Primary Master Hard Disk Error
Primary Slave Hard Disk Error
Secondary Master Hard Disk Error
Secondary Slave Hard Disk Error
PS2 Mouse not found

Keyboard error

System Haulted

Press TAB to show POST screen

Description/Action
The CMOS Date and/or Time are
invalid. This error can be resolved
by readjusting the system time in
AMIBIOS Setup.
The CMOS battery is no longer
functional.
Replace the battery.
Checksum of CMOS is incorrect.
The computer loads the default
configuration settings. This error
might indicate that CMOS has
become corrupt due to a weak
CMOS battery.
The IDE/ATAPI device configured
as Primary Master/Primary Slave/
Secondary Master/Secondary Slave
could not be found or initialized.
Make sure the hard drive is correctly
installed.
PS2 Mouse support is enabled in
the BIOS setup butthe device is not
detected. You can plug PS2 Mouse
or set PS2 Mouse support is auto.
Cannot initialize the keyboard.
Make sure the keyboard is properly
connected to the computer and
that no keys are held pressed during
POST.
To purposely configure the
computer without a keyboard, set
keyboardless operation in Setup to
Enable. The BIOS then ignores the
missing keyboard during POST.
The system has been halted. A reset
or power cycle is required to reboot
the machine. This message appears
after a fatal error has been detected.
Pressing the TAB key permits the
user to toggle between the default
POST display screen and a custom
POST display screen.

Chapter 6. Symptom-to-FRU Index

POST Error Message
Reboot and Select proper Boot
device or Insert Boot Media in
selected Boot device

Description/Action
The BIOS was unable to find a
suitable boot device.
Make sure the boot drive is properly
connected to the computer.
Make sure you have bootable
media.

Undetermined problems
If this computer has a parallel ATA hard disk drive, make sure that the hard
disk drive is jumpered as a master and the optical drive is jumpered as a
slave.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a
time.
a. External devices (modem, printer, or mouse)
b. Any adapters
c. Memory modules
d. Extended video memory
e. External Cache
f. External Cache RAM
g. Hard disk drive
h. Diskette drive
3. Power-on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
If all devices and adapters have been removed, and the problem
continues, replace the system board.

Hardware Maintenance Manual

Replacing hardware

Attention

Do not remove the computer cover or attempt any repair before
reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware
Maintenance Manual (HMM) for the computer. To obtain copies of the
Safety and Warranty Guide or HMM, go to the Support Web site at
http://consumersupport.lenovo.com

Note

Use only parts provided by Lenovo.

General information
Pre-disassembly instructions
Before proceeding with the disassembly procedure, make sure that you
do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug all power and signal cables from the computer.
3. Place the system on a flat, stable surface.

Chapter 7. Replacing hardware

Removing the computer cover
Attention

Turn off the computer and wait 3 to 5 minutes to let the computer
cool before removing the computer cover.

To remove the computer cover:
1. Remove any media (diskettes, CDs, or memory cards) from the drives,
shut down your operating system, turn off all attached devices, and
the computer.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power
cords, input/output (I/O) cables, and any other cables that are
connected to the computer. Refer to “Locating connectors on the rear
of the computer”.
4. Remove the two screws that secure the computer cover at the rear of
the chassis.
5. Slide the computer cover to the rear of the chassis to remove.
Note

For this procedure, it helps to lay the computer on its side.

Hardware Maintenance Manual

Removing the front bezel
To remove the front bezel:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note

For this procedure, it helps to lay the computer on its side.
2. Remove the front bezel by releasing the three plastic tabs inside the
chassis and push the bezel outward as shown.

Chapter 7. Replacing hardware

3. To reinstall the bezel, align the plastic tabs on the bottom of the bezel
with the corresponding holes in the chassis, and then snap it into
position at the bottom and top of the chassis.
4. Refer to the “Completing the installation”.

Replacing a memory module
Attention

Hardware Maintenance Manual

To replace a memory module:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note

For this procedure, it helps to lay the computer on its side.
2. Locate the memory module connectors. Refer to “Locating
components”.
3. Remove the memory module being replaced by opening the retaining
clips as shown.

4. Position the new memory module over the memory connector. Make
sure the notch on the memory aligns correctly with the connector
key on the system board. Push the memory module straight down
into the connector until the retaining clips close.

5. Refer to the “Completing the installation”.

Chapter 7. Replacing hardware

Replacing the hard disk drive
Attention

To replace the hard disk drive:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note

For this procedure, it helps to lay the computer on its side.
2. Disconnect the data and power cables from the hard disk drive.
3. Use the plastic handle to slide the hard disk drive out of the drive bay.

Hardware Maintenance Manual

4. Slide the new hard disk drive into the drive bay.
5. Pivot in the drive bay in place.
6. Connect the power and signal cables to the hard disk drive. Refer to
“Identifying parts on the system board”.
7. Refer to the “Completing the installation”.

Replacing an optical drive
Attention

To replace an optical drive
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the front bezel. Refer to “Removing the front bezel”.
3. Disconnect the data and power cables from the rear of the optical
drive.

Chapter 7. Replacing hardware

4. Press the release button and push the optical drive straight out of the
front of the chassis.

5. Slide the new optical drive into the bay from the front until it snaps
into position.
6. Connect the data and power cables to the drive.
7. Install the front bezel. Refer to the steps 3 of the “Removing the front
bezel”.
8. Install the computer cover. Refer to “Completing the installation”.

Replacing the system fan assembly
Attention

Hardware Maintenance Manual

To replace the system fan assembly:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Locate the system fan assembly. Refer to “Identifying parts on the
system board”.
3. Disconnect the system fan assembly cable from the system board.
Refer to“Identifying parts on the system board”.
4. Pull the system fan assembly out of chassis.

Chapter 7. Replacing hardware

5. Install the new system fan assembly by aligning the rubber mounts of
the system fan assembly with the holes on the chassis and push the
rubber mounts through the holes.

6. Pull on the tips of the rubber mounts until the fan assembly is in place.
7. Connect the system fan assembly cable to the system fan connector
on the system board.
8. Refer to the “Completing the installation”.

Hardware Maintenance Manual

Replacing the heat sink assembly
Attention

To replace the heat sink assembly:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Lay the computer on its side.
3. Locate the heat sink. Refer to “Identifying parts on the system board”.
4. Disconnect the heat sink and the fan assembly cable from the system
board.
5. Remove the four screws
the system board.

securing the heat sink and fan assembly to

6. Lift the failing heat sink and fan assembly off the system board.

Chapter 7. Replacing hardware

7. Use the thermal grease syringe to place five drops of grease on the
top of the microprocessor. Each drop of grease should be 0.03ml (3
tick marks on the grease syringe).

8. Install the heat sink and fan assembly on the heat sink retention
bracket.
9. Reconnect the disconnected cables to the system board.
10. Refer to the “Completing the installation”.

Replacing a PCI or AGP adapter
Attention

To replace an adapter:
1. Remove the computer cover. Refer to “Removing the computer cover”.

Hardware Maintenance Manual

2. At the rear of the computer, press the release button to open the
adapter latch and remove the adapter by pulling it straight out of
the adapter connector.

Chapter 7. Replacing hardware

3. Install the new adapter into the same adapter connector.

4. Ensure the adapter is fully seated into the adapter connector.
5. At the rear of the computer, pivot the adapter latch to the closed
position to secure the adapter.
6. Refer to the “Completing the installation”.

Hardware Maintenance Manual

Note 1

eplacement of some models equipped with graphic adapter
bracket is different.

Please remove the plastic bracket first as the following:
1. Remove the two screws that secure the plastic bracket at the bottom
of the chassis.
2. Lift the plastic bracket out of the chassis.
3. Then remove the adapter as above.

After the Graphic Adapter is installed , install the bracket
as the following:
1. Install the plastic bracket into the chassis so that the screw holes in
the plastic bracket align with those in the chassis. Let the slot on the
plastic bracket clip the adapter.

Chapter 7. Replacing hardware

2. Install the two screws to secure the plastic bracket.
Note
Use only the screws provided by Lenovo.

Note 2

Replacement of some models equipped with graphic adapter
bracket is different.

Please remove the bracket first as the following:
1. Remove the screw that secures the bracket at the side of the chassis.

Hardware Maintenance Manual

2. Press the pin on one end of the metal bracket and pull the metal
bracket straight out of the chassis.

After the Graphic Adapter is installed, install the bracket
as the following:
1. Install the metal bracket into the chassis so that the screw hole in the
metal bracket aligns with the hole in the chassis. Let the slot on the
metal bracket clip the adapter.

Chapter 7. Replacing hardware

2. Screw back the screws on the metal bracket.
Note
Use only the screws provided by Lenovo.

Replacing the CPU
Attention

Hardware Maintenance Manual

To replace an CPU
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the front bezel. Refer to “Removing the front bezel”.
3. Remove the system board. Refer to “Replacing the heat sink assembly”.
4. Remove the heat sink and fan assembly. Refer to “Replacing the heat
sink assembly”.
5. To remove the microprocessor from the system board, lift the small
handle and open the retainer .

Important
Do not touch the gold contacts on the bottom of the
microprocessor. When handling the microprocessor, touch only the
sides.
6. Lift the microprocessor straight up and out of the socket.

Chapter 7. Replacing hardware

Note

a. Note the orientation of the notches on the microprocessor.
This is important when reinstalling the microprocessor on the new
system board.

b. Do not drop anything onto the microprocessor socket while it is
exposed. The socket pins must be kept as clean as possible.

7. Make sure that the microprocessor retainer is fully open.
8. Holding the microprocessor with your fingers, remove the protective
cover that protects the gold contacts on the new microprocessor .

9. Holding the microprocessor with your fingers, position the
microprocessor so that the notches on the microprocessor are aligned
with the tabs in the microprocessor socket.

Hardware Maintenance Manual

Important
To avoid damaging the microprocessor contacts, do not tilt the
microprocessor when installing it into the socket.
10. Lower the microprocessor straight down into the system board socket
of the system board.

11. To secure the microprocessor in the socket, close the microprocessor
retainer and lock it into position with the small handle.
12. Use the thermal grease syringe to place five drops of grease on the
top of the microprocessor. Each drop of grease should be 0.03ml (3
tick marks on the grease syringe).

13. Install the heat sink and fan assembly on the system board.
14. Connect the heat sink and fan assembly cable to the system board.
Refer to the “Identifying parts on the system board”.
15. Install the system board into the chassis and allign the screw holes
with those in the chassis.Insert and tighten the screws that secure the
system board. Refer to the “Replacing the system board”.
16. Reconnect the disconnected cables to the system board.
17. Refer to the “Completing the installation”.

Chapter 7. Replacing hardware

Replacing the keyboard
To replace the keyboard:
1. Remove any media (diskettes, CDs, or memory cards) from the drives,
shut down your operating system, and turn off all attached devices
and the computer.
2. Unplug all power cords from electrical outlets.
3. Locate the connector for the keyboard. Refer to “Locating connectors
on the rear of the computer” and “Locating connectors on the front of
the computer”.
Note

Your keyboard might be connected to the standard keyboard
connector at the rear of the computer or to a USB connector
either the front or rear of the computer.

4. Disconnect the failing keyboard cable from the computer and connect
the new keyboard cable to the same connector.
5. Refer to the “Completing the installation”.

Replacing the mouse
To replace the mouse:
1. Remove any media (diskettes, CDs, or memory cards) from the drives,
shut down your operating system, and turn off all attached devices
and the computer.
2. Unplug all power cords from electrical outlets.
3. Locate the connector for the mouse. Refer to “Locating connectors on the front
of the computer” and “Locating connectors on the rear of the computer”.

Hardware Maintenance Manual

Note

Your mouse might be connected to the standard mouse connector
at the rear of the computer or to a USB connector at either the
front or rear of the computer.

4. Disconnect the failing mouse cable from the computer.
5. Connect the new mouse cable to the connector.
6. Refer to the “Completing the installation.”

Replacing the External speaker
1. Remove any media (diskettes, CDs, or memory cards) from the drives,
shut down the computer, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.
3. Locate the Speaker. Refer to “Locating connectors on the rear of the
computer” and “Locating connectors on the front of the computer”.
Your speaker might be connected to the Audio connector to an
Audio connector at either the front or rear of the computer. Locate the
connector for the speaker.

Chapter 7. Replacing hardware

4. Disconnect the failing speaker cable from the computer and connect
the new speaker cable to the same connector.

Completing the installation
After replacing the parts, you need to close the computer cover and
reconnect cables, including telephone lines and power cords. Also,
depending on the part that was replaced, you might need to confirm the
updated information in the Setup Utility program. Refer to “Starting the
Setup Utility” in the User Guide or in the Hardware Maintenance Manual.

To complete the part installation:
1. Ensure that all components have been reassembled correctly and
that no tools or loose screws are left inside your computer. Refer to
“Locating components” for the location of the various components.
2. Make sure that the cables are routed correctly before replacing the
computer cover.
3. Position the computer cover on the chassis so that the rail guides on
the bottom of the computer cover engage the rails. Then, push the
computer cover closed until it snaps into position.

Hardware Maintenance Manual

4. Reconnect the external cables and power cords into the computer.
Refer to “Locating connectors on the front of the computer” and
“Locating connectors on the rear of the computer”.
5. To update your configuration settings, refer to “Starting the Setup
Utility” in the User Guide or in the Hardware Maintenance Manual.
Note

In most areas of the world, Lenovo requires the return of the
defective CRU. Information about this will come with the CRU or will
come a few days after the CRU arrives.

Chapter 8. Additional Service Information

Additional Service
Information
(Type G43)

This chapter provides additional information that the service
representative might find helpful.

Power management
Power management reduces the power consumption of certain
components of the computer such as the system power supply, processor,
hard disk drives, and some monitors.

Automatic configuration and power interface (ACPI)
BIOS
Being an ACPI BIOS system, the operating system is allowed to control
the power management features of the computer and the setting for
Advanced Power Management (APM) BIOS mode is ignored. Not all
operating systems support ACPI BIOS mode.

Automatic Power-On features
The Automatic Power-On features within the Power Management menu
allow you to enable and disable features that turn on the computer
automatically.
•• Wake On LAN: This future allow system wake up by Lan card and
onboard lan.
•• Ring Wakeup: With this feature set to Enabled, the computer will turn
on automatically when a ring is detected on the internal modem.
•• Wake Up On Alarm: You can specify a date and time at which the
computer will be turned on automatically. This can be either a single
event or a daily event.
•• PCI Wake Up: This feature allows PCI cards which support this
•• cappability to wake this system.

Hardware Maintenance Manual

Statement

Thanks for using Lenovo products.
Carefully read all of the documents shipped with your computer before
you install and use the product for the first time. Lenovo will not assume
responsibility for damage that results from failure to operate the product
according to instructions and requirements described in the manuals
included with your computer. Lenovo will not assume responsibility
for any loss caused except that caused by the installation or operations
carried out by Lenovo professional service staff.
Lenovo has made every attempt to ensure that the manuals included with
your computer, are correct and accurate, but makes no guarantee that the
publications are error free.
To provide better service, Lenovo reserves the right to improve and/or
modify the products and software programs described in the manuals
included with your computer and the content of the manual at any time
without additional notice.
All of the manuals included with your computer are provided to help you
use Lenovo products appropriately, but do not provide any description
of the software/hardware configuration for the product. For the
configuration of the product, refer to related contract (if any), product
packing list for the product or retailer.
The content of the manuals included with your computer is protected
by copyright laws and rules. None of the manuals included with
your computer may be reproduced or transcribed by any means, or
transmitted through wired or wireless network in any form, or translated
into any language without prior written permission of Lenovo. All Lenovo
publications included with your system are protected by Copyright ©
2007, 2009 Lenovo.
The software and hardware configuration included with your computer
depends on the actual configuration of the computer and may differ from
other similar models.

Appendix. Statement

Customers are welcome to contact us for any inconsistency between the
product and the manuals included with your computer. For the latest
information or any questions or comments, please visit consumer support
website at:
http://consumersupport.lenovo.com

Lenovo is a registered trademark of Lenovo.
Microsoft, Windows, and Windows Vista are trademarks of the Microsoft
group of companies.
Intel Inside is the registered trademark of Intel.
AMD, the AMD Arrow logo, ATI, the ATI logo, AMD Athlon, AMD LIVE, AMD
Opteron, AMD Phenom, AMD Sempron, Avivo, Catalyst, Cool ‘n’ Quiet,
CrossFireX, Overdrive, Powerplay, Radeon, The Ultimate Visual Experience,
and combinations thereof are trademarks of Advanced Micro Devices, Inc.
in the United States and/or other jurisdictions.
The table above includes the logo and registered trademarks of Lenovo
and its partners.
Other registered trademarks mentioned in all the manuals included with
your computer belong to the specific company respectively.
The manual included with your computer is protected by copyright laws
and rules. None of the manuals included with your computer may be
reproduced or transcribed by any means, or transmitted through wired
or wireless network in any form, or translated into any language without
prior written permission of Lenovo.
Names or marks of certain companies mentioned in the manuals included
with your computer or this document are only used to state trademark
rights, and they will not necessarily indicate that related software or
hardware is included. The concrete configuration of the product depends
on the description of the specific model.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24
Instance ID                     : uuid:83f52507-b66d-f146-ac61-5a675179a361
Document ID                     : adobe:docid:indd:6d27e4bc-6214-11dc-b687-905b70947d35
Rendition Class                 : proof:pdf
Derived From Instance ID        : 7d7aa313-53dc-11dc-91ba-8960f60322cb
Derived From Document ID        : adobe:docid:indd:bbd7f1eb-5180-11dc-b622-d4cd06283be3
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:dd1f10d6-85c5-11db-b0c4-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:18d704fe-85cf-11db-b0c4-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:dd1f10d6-85c5-11db-b0c4-00112472c304, uuid:f6170950-865d-11db-b4e6-00112472c304, uuid:cedbfde8-85c5-11db-b0c4-00112472c304, uuid:815d9006-865e-11db-b4e6-00112472c304, uuid:e1b6c5ce-866f-11db-b4e6-00112472c304, uuid:6361e29f-03da-11de-bb72-000a95bb06ea, uuid:b4ee1fd2-06d0-11de-b080-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:e37eb727-0469-11de-9086-000a95bb06ea, uuid:cdeabc53-06d0-11de-b080-000a95bb06ea, uuid:06c37ebc-06d1-11de-b080-000a95bb06ea, uuid:1e3bb4de-06d1-11de-b080-000a95bb06ea, uuid:34639592-06d1-11de-b080-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:f726b214-0469-11de-9086-000a95bb06ea, uuid:6f2d9078-06d1-11de-b080-000a95bb06ea, uuid:83fe2ca5-06d1-11de-b080-000a95bb06ea, uuid:b33f3fa2-0469-11de-9086-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:a71c3bf8-0469-11de-9086-000a95bb06ea, uuid:e1604175-a39f-11dc-a33a-000a95bb06ea, uuid:6afc668f-046a-11de-9086-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:d4ef0ee0-046a-11de-9086-000a95bb06ea, uuid:c202ddcd-0469-11de-9086-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:8f9e1984-940a-11dc-800e-000a95bb06ea, uuid:75d6e782-046a-11de-9086-000a95bb06ea, uuid:f96981ea-046a-11de-9086-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:06b073be-046a-11de-9086-000a95bb06ea, uuid:d6490f69-40ca-11dc-be70-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:141459c4-046a-11de-9086-000a95bb06ea, uuid:96a1c008-40cb-11dc-be70-000a95bb06ea, uuid:3355e4d7-0469-11de-9086-000a95bb06ea, uuid:15fc6933-40cc-11dc-be70-000a95bb06ea, uuid:254c1ae8-03e3-11de-bb72-000a95bb06ea
Manifest Reference Document ID  : uuid:2F408543879B11DBA24FC4363B274880, uuid:2F408543879B11DBA24FC4363B274880, uuid:2F408545879B11DBA24FC4363B274880, uuid:2F408543879B11DBA24FC4363B274880, uuid:2F408543879B11DBA24FC4363B274880, uuid:2F408543879B11DBA24FC4363B274880, uuid:2F408543879B11DBA24FC4363B274880, uuid:2F40854B879B11DBA24FC4363B274880, uuid:2F408543879B11DBA24FC4363B274880, uuid:2F408545879B11DBA24FC4363B274880, uuid:564A95E1883311DBA7D2BB47F75E863F, uuid:2F408543879B11DBA24FC4363B274880, uuid:564A95E3883311DBA7D2BB47F75E863F, uuid:564A95E7883311DBA7D2BB47F75E863F, uuid:FDDF56368005DE11957BB19B7022EC91, uuid:b4ee191c-06d0-11de-b080-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:e37eb01f-0469-11de-9086-000a95bb06ea, uuid:cdeab2b0-06d0-11de-b080-000a95bb06ea, uuid:06c377aa-06d1-11de-b080-000a95bb06ea, uuid:1e3badf0-06d1-11de-b080-000a95bb06ea, uuid:34638c4e-06d1-11de-b080-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:f726a88d-0469-11de-9086-000a95bb06ea, uuid:6f2d8747-06d1-11de-b080-000a95bb06ea, uuid:83fe2554-06d1-11de-b080-000a95bb06ea, uuid:b33f35ff-0469-11de-9086-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:a71c326e-0469-11de-9086-000a95bb06ea, uuid:0555F1C2279EDC11A667CD95B3EEA191, uuid:6afc5cf4-046a-11de-9086-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:d4ef0548-046a-11de-9086-000a95bb06ea, uuid:c202d436-0469-11de-9086-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:AF984C2E6093DC11A06A981F087BCD07, uuid:75d6de03-046a-11de-9086-000a95bb06ea, uuid:f9697837-046a-11de-9086-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:06b069b6-046a-11de-9086-000a95bb06ea, uuid:d649056a-40ca-11dc-be70-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:14145044-046a-11de-9086-000a95bb06ea, uuid:96a1b608-40cb-11dc-be70-000a95bb06ea, uuid:3355de24-0469-11de-9086-000a95bb06ea, uuid:15fc5f0e-40cc-11dc-be70-000a95bb06ea, uuid:254c0f8b-03e3-11de-bb72-000a95bb06ea
Create Date                     : 2009:07:29 16:47:25+08:00
Modify Date                     : 2009:07:29 16:47:41+08:00
Metadata Date                   : 2009:07:29 16:47:41+08:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7261 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 57
Creator                         : Adobe InDesign CS3 (5.0)

EXIF Metadata provided by EXIF.tools

Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) User Idea Centre K315 Desktop (ideacentre) Type 10079

Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) ハードウエアメンテナンスマニュアル - Lenovo IdeaCentre K3 シリーズ K330 Desktop (ideacentre) - Type 7727 Lenovo IdeaCentre K3 Series Hardware Maintenance Manual (English)

Lenovo Ideacentre K330B Hardware Maintenance Manual (English) Lenovo IdeaCentre K330B Hardware Maintenance Manual K330B Desktop (ideacentre) - Type 10066 Lenovo IdeaCentre K330B Hardware Maintenance Manual (English)

Navigation menu

Versions of this User Manual:

Views

Navigation

Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) User Idea Centre K315 Desktop (ideacentre) Type 10079

Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) ハードウエア メンテナンス マニュアル - Lenovo IdeaCentre K3 シリーズ K330 Desktop (ideacentre) - Type 7727 Lenovo IdeaCentre K3 Series Hardware Maintenance Manual (English)

Lenovo Ideacentre K330B Hardware Maintenance Manual (English) Lenovo IdeaCentre K330B Hardware Maintenance Manual K330B Desktop (ideacentre) - Type 10066 Lenovo IdeaCentre K330B Hardware Maintenance Manual (English)

Navigation menu

Lenovo Ideacentre K3 Series Hardware Maintenance Manual (English) ハードウエアメンテナンスマニュアル - Lenovo IdeaCentre K3 シリーズ K330 Desktop (ideacentre) - Type 7727 Lenovo IdeaCentre K3 Series Hardware Maintenance Manual (English)