Leviton DDMX1 Remote Dimmer Switch User Manual DI 000 DDMX1 02A X3 indd

Single Pole (One location) or 3-Way (Multi-location)

Universal Incandescent/Magnetic Low Voltage/Fluorescent or LED Dimmer

Cat. No. DDMX1-BL, 1000VA, 1000W, 450W LED/CFL (Lighted)

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

IMPORTANT: For 3-Way applications, note that one of the screw terminals

from the old switch being removed will usually be a different color (Black)

• Pull off pre-cut insulation from dimmer leads.

• Make sure that the ends of the wires from the wall box are straight

• Remove insulation from each wire in the wall box as shown.

• For Single-Pole Application, go to Step 4a.

In multi-dimmer installations, the reduction of the dimmer’s capacity may

be required. Refer to the chart for maximum load per dimmer.

If installing Dimmer in a single device application, proceed with the

INSTALLING YOUR DIMMER section. If installing Dimmer in a

multi-device application, proceed as follows:

to attach

is off before wiring!

of these configurations, consult an electrician.

(measure bare

wire here)

Pull off pre-cut insulation from dimmer leads. Make sure that

the ends of the wires from the wall box are straight (cut if

as shown:

is determined by the efficiency of the transformer in the low-voltage lighting

wattage is determined by the efficiency of the Mark 10

following table shows the maximum number of ballasts that can be connected

to a single dimmer for different Mark 10

table shows maximum ballasts for multi-gang installations.

To determine total ballast load, add the line current found on the ballast label

for all ballasts in the circuit. This will indicate the total load for the control.

•

TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle, a motor- or a transformer-operated appliance.

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• Use ONLY with the appropriate Advance Transformer 120V Mark 10® Powerline or Lutron Tu-Wire® electronic ballasts for controlling the specific fluorescent lamps in Fluorescent Mode.

• Use with magnetic low voltage transformers, incandescent, or 120V halogen fixtures only. Use a Leviton electronic low voltage dimmer to control electronic (solid state) low voltage transformers.

• When retrofitting Mark 10® Powerline dimming ballasts into fixtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer

operation and prevent damage to the dimmer ballast. Refer to the instructions provided with the ballast.

• The Decora

• Dimmer may feel warm to the touch during normal operation.

dimmer performance.

Line Hot connection and a Neutral connection. A Neutral wire to the

matching remote needs to be added as shown.

cannot exceed 300 ft (90 m).

• Green or bare copper wire in wall box to Green terminal screw.

Load connection and a Neutral connection.

• Green or bare copper wire in wall box to Green dimmer lead.

• Load wall box wire identified (tagged) when removing old switch to

• First Traveler Line Hot to Black dimmer lead.

• Remove Red insulating label from Yellow/Red dimmer lead.

• Second Traveler wall box wire (note color as above) to

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details

A-3) Minimum Brightness Level: Sets the minimum dimming level.

A-4) Preset ON Level: Sets the turn on brightness level regardless of

the previous set light level.

Definition of B Modes

B-1) ON Fade Rate: Sets the amount of time in seconds it takes the

lights to turn ON to maximum brightness.

B-2) OFF Fade Rate: Sets the amount of time in seconds it takes the

lights to turn OFF from maximum brightness.

B-3) LED Options: Sets the time period in seconds the Locator LED

Rocker this setting will automatically be saved and the device will exit

Programming Mode B.

To enter Program Mode A:

Press and hold the TOP of the Rocker and the TOP of the DIM/BRIGHT

Bar simultaneously for 5 seconds until the Locator LED begins to blink.

A-1) Upon releasing the TOP of the Rocker and the TOP of the DIM/

BRIGHT Bar, the Locator LED will continue to blink once per

second to display the device is in Program Mode A-1, Load Type

Definition of LEDs

Bottom LED = LED 1

Top LED = LED 7

programming mode.

DIM/BRIGHT Bar

Press the TOP half of the DIM/BRIGHT Bar – Lights brighten to desired

If you continue to hold, the lights will DIM to minimum level and

then turn OFF.

• Position all wires to provide room

in outlet wall box for device.

• Ensure that the word “TOP” is

facing up on device strap.

• Partially screw in mounting screws

in wall box mounting holes.

shown in diagram in order to relieve

stress when mounting device.

NOTE: If using in a dimmable fluorescent application see

telephone at 1-800-405-5320.

TURN OFF POWER AT

CIRCUIT BREAKER OR FUSE.

Restore power at circuit breaker or fuse.

Installation is complete.

Installation may now be completed by

On the dimmer, hold the TOP of the rocker until the locator LED starts

to blink. The dimmer is now reset. Once the dimmer is reset, it may be

necessary to re-pair with the your application.

OTE: To pair your dimmer with your mobile device, download the

Store or your iTunes account. Contact Leviton’s Techline at 1-800-

824-3005 or visit Leviton’s website at www.leviton.com for additional

This device complies with Part 15 of the FCC Rules. Operation is subject to

in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment OFF

and ON, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the equipment and the receiver.

Copyright and Trademark Information

The Bluetooth® word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc., used under license by Leviton.

Use herein of third party trademarks, service marks, trade names, brand

names and/or product names are for informational purposes only, are/may

be the trademarks of their respective owners; such use is not meant to imply

affiliation, sponsorship, or endorsement.

No part of this document may be reproduced, transmitted or transcribed

7 100% 0%

6 97% 5%

5 95% 8%

4 90% 11%

3 85% 14%

2 80% 17%

1 75% 20%

5 6 seconds 6 seconds

6 10 seconds 10 seconds

7 25 seconds 25 seconds

The Locator LED will blink 4 times per second to indicate Program

Mode A-4, Preset ON Level. To change the current Preset ON

desired, press and hold the BOTTOM half of the DIM/BRIGHT Bar

until no LED is lit (default setting). By tapping the TOP of the Rocker

this setting will automatically be saved and the device will exit

Programming Mode A.