Life Fitness LFNFCCR1 NFC Card Reader Module User Manual I

Life Fitness NFC Card Reader Module I

UserManual.wiki >

Life Fitness >

LFNFCCR1 User Manual >

user manual I HTML Version

1. user manual I
2. User manual

user manual I

Page 1 of 9

User & Integration Manual

LifeFitness NFC Card Reader

1.1

13.56 MHz Multi Standard – NFC Reader/Writer Module

User & Integration Manual

Life Fitness NFC Card Reader Module

Content

1. Short description ................................................................................................................................. 3

2. Module installation ............................................................................................................................. 4

2.1 Physical dimensions ............................................................................................................................ 4

2.2 NFC Antenna location on PCB .............................................................................................................. 4

3. FCC and RSS compliance statements ................................................................................................... 5

4. FCC and IC information label location.................................................................................................. 6

5. End device labeling instructions .......................................................................................................... 7

6. Revision history ................................................................................................................................... 9

User & Integration Manual

Life Fitness NFC Card Reader Module

1. Short description

Power supply

Via host flat-band cable connection 5V (+- 5%)

Operating temperature: 0°C to 60°C

Storage temperature: 0°C to 60°C

Supported 13,56MHz RF standards

▪ ISO/IEC 14443 – ASK modulation

▪ ISO/IEC 15693 – ASK modulation (support depends on used RF frontend derivative)

Host communication (via I2C)

Antenna connection: embedded PCB antenna

Short functional description:

▪ After power-up of the module the NCI NFC controller chip is ready to receive commands via

its I2C application controller (host) interface and performs the related NFC tag interactions

according to the implemented NFC Forum NCI specification

▪ The 13,56Mhz RF field is switched on depending on the commands received.

User & Integration Manual

Life Fitness NFC Card Reader Module

2. Module installation

2.1 Physical dimensions

▪ Outer dimensions 76mm (2,99 inch) x 49 (1,93 inch)

▪ Mounting holes (4 x 2,7mm/0,106 inch).

▪ Mount the module properly into the end device.

▪ Mounting holes on the connector side are connected to system ground – it is recommended to

connect at least one mounting whole to the end-device´s system ground.

▪ Attach connection cable to connector P1 (8 Pin header) to the end device´s application host

2.2 NFC Antenna location on PCB

Module back side

Module top side

User & Integration Manual

Life Fitness NFC Card Reader Module

3. FCC and RSS compliance statements

FCC COMPLIANCE STATEMENT

NOTE:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Caution!

The Federal Communications Commission (FCC) warns the users that changes or modifications to the

unit not expressly approved by the party responsible for compliance could void the user's authority

to operate the equipment.

FCC §15.105 (b):

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a installation. If this equipment does cause harmful

interference to radio or television reception, which can be deter-mined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

User & Integration Manual

Life Fitness NFC Card Reader Module

RSS COMPLIANCE STATEMENT

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the

following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

1) l’appareil ne doit pas produire de brouillage;

2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

User manuals for transmitters equipped with detachable antennas shall also contain the following

notice in a conspicuous location:

This radio transmitter (identify the device by certification number) has been approved by Industry

Canada to operate with the antenna types listed below with the maximum permissible gain

and required antenna impedance for each antenna type indicated. Antenna types not included in

this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited

for use with this device.

Immediately following the above notice, the manufacturer shall provide a list of all antenna types

approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi)

4. FCC and IC information label location

The required FCC ID and IC identifiers are located on the module on the top side of the module as

shown in below image.

User & Integration Manual

Life Fitness NFC Card Reader Module

5. End device labeling instructions

FCC notes for host devices. The end device must be labeled with:

Contains FCC ID: LM6-LFNFCCR1

Contains IC: 23315-LFNFCCR1

Labelling Requirements

In addition following statement shall be placed on the device:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Where the product is so small or for such use that it is not practicable to place the statement on it,

the statement can be placed in a prominent location in the instruction manual.

Information to the user

- For Class A devices the manual of the host shall include the following statement:

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

- For Class B devices the manual of the host shall include the following statement: