MTD 11A 414E700 User Manual LAWN MOWER Manuals And Guides 1108461L

User Manual: MTD 11A-414E700 11A-414E700 MTD LAWN MOWER - Manuals and Guides View the owners manual for your MTD LAWN MOWER #11A414E700. Home:Lawn & Garden Parts:MTD Parts:MTD LAWN MOWER Manual

Open the PDF directly: View PDF .
Page Count: 20

Operator's Manual

21" Rear Discharge

Push Mower

Model Series

410 through 419

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-cov-

ered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable

local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State

of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer

or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

MTD LLC,P.O.BOX361131CLEVELAND,OHIO44136-0019

PRINTED IN U.S.A. FORM NO. 770-10124E

(10/2003)

TABLEOFCONTENTS

Content

Important Safe Operation Practices

Slope Gauge

Assembling Your Lawn Mower

Know Your Lawn Mower

Operating Your Lawn Mower

Page Content Page

3 Making Adjustments 12

6 Maintaining Your Lawn Mower 13

7 Troubleshooting 15

10 Illustrated Parts List 16

11 Warranty 20

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new lawn mower. It will help you assemble, prepare and

maintain the unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the

equipment and copy the information from it in the space provided below. A sample model plate is

also given below. You can locate the model plate by standing at the operating position and

looking down at the rear of the deck. This information will be necessary to use the

manufacturer's web site and/or help from the Customer Support Department or an authorized

service dealer.

_')ff M,-DLLC

P. O. BOX 361131

CLEVELAND,OH 44136

338-228-4683

www.mtdproducts.com 888-888-7318

Copy the model number here:

Copy the serial number here:

CUSTOMERSUPPORT

Please doNOTreturnthe unitto the retailer from whichit waspurchased,withoutfirstcontactingCustomerSupport.

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, you can seek help from the experts. Choose from the options below:

En ine

Visit mtdproducts.com for many useful suggestions. Click on Customer Support button and

you will get the four options reproduced here. Click on the appropriate button and help is

immediately available.

answer you are

looking for could be just

a mouse c//cA awayf

answer aye

looking for could be just

a mouse cficA away_

If you prefer to reach a Customer Support Representative, please call 1(800) 800-7310.

The engine manufacturer is responsible for all engine-related issues with regards to

performance, power-rating, specifications, warranty and service. Please refer to the engine

manufacturer's Owner's/Operator's Manual, packed separately with your unit, for more

information.

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual

before attempting to operate this machine. Failure to comply with these instructions may result in personal

injury. When you see this symbol--HEED ITS WARNING.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or

emit chemicals known to State of California to cause cancer and birth defects or other

reproductive harm.

WARNING: This machine was built to be operated according to the rules for safe operation in this

manual. As with any type of power equipment, carelessness or error on the part of the operator can result in

serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to

observe the following safety instructions could result in serious injury or death.

GeneralOperation

1. Read this operator's manual carefully in its entirety

before attempting to assemble this machine. Read,

understand, and follow all instructions on the machine

and in the manual(s) before operation. Be completely

familiar with the controls and the proper use of this

machine before operating it. Keep this manual in a safe

place for future and regular reference and for ordering

replacement parts.

2. This machine is a precision piece of power equipment,

not a plaything. Therefore, exercise extreme caution at all

times. Your unit has been designed to perform one job: to

mow grass. Do not use it for any other purpose.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the operation instructions and safety rules in

this manual and should be trained and supervised by a

parent. Only responsible individuals who are familiar with

these safe operation rules should use this machine.

4. Thoroughly inspect the area where the equipment is to

be used. Remove all stones, sticks, wire, bones, toys and

other foreign objects which could be tripped over or

picked up and thrown by the blade. Thrown objects can

cause serious personal injury. Plan your mowing pattern

to avoid discharge of material toward roads, sidewalks,

bystanders and the like. Also, avoid discharging material

against a walt or obstruction which may cause

discharged material to ricochet back toward the operator.

5. To help avoid blade contact or a thrown object injury, stay

in the operator zone behind the handles and keep

bystanders, helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop machine if

anyone enters the area.

6. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

7. Wear sturdy, rough-soled work shoes and close-fitting

slacks and shirts. Shirts and pants that cover the arms

and legs and steel-toed shoes are recommended. Never

operate this machine in bare feet, sandals, slippery or

light weight (e.g. canvas) shoes.

8. Do not put hands or feet near rotating parts or under the

cutting deck. Contact with the blade can amputate hands

and feet.

9. A missing or damaged discharge cover can cause blade

contact or thrown object injuries.

10. Many injuries occur as a result of the mower being pulled

over the foot during a fall caused by slipping or tripping.

Do not hold on to the mower if you are falling; release the

handle immediately.

11. Never pull the mower back toward you while you are

walking. If you must back the mower away from a wall or

obstruction, first took down and behind to avoid tripping

and then follow these steps:

a. Step back from the mower to fully extend your

arms.

b. Be sure you are welt balanced with sure footing.

c. Pull the mower back slowly, no more than halfway

toward you.

d. Repeat these steps as needed.

5. Do not operate the mower while under the influence of

alcohol or drugs.

6. Do not engage the self-propelled mechanism on units

so equipped while starting engine.

7. The blade control handle is a safety device. Never

attempt to bypass its operation. Doing so makes the

safety device inoperative and may result in personal

injury through contact with the rotating blade. The blade

control handle must operate easily in both directions and

automatically return to the disengaged position when

released.

8. Never operate the mower in wet grass. Always be sure of

your footing. A slip and fall can cause serious personal

injury. If you feel you are losing your footing, release the

blade control handle immediately and the blade will stop

rotating within three seconds.

9. Mow in daylight or good artificial light. Walk, never run.

10. Stop the blade when crossing gravel drives, walkways

or roads.

11. If the equipment should start to vibrate abnormally, stop

the engine and check immediately for the cause.

Vibration is generally a warning of trouble.

12. Shut the engine off and wait until the blade comes to a

complete stop before removing the grass catcher or

uncloggingthechute.Thecuttingbladecontinuesto

rotateforafewsecondsaftertheengineisshutoff.

Neverplaceanypartofthebodyinthebladeareauntil

youaresurethebladehasstoppedrotating.

13.Neveroperatemowerwithoutpropertrailshield,

dischargecover,grasscatcher,bladecontrolhandleor

othersafetyprotectivedevicesinplaceandworking.

Neveroperatemowerwithdamagedsafetydevices.

Failuretodoso,canresultinpersonalinjury.

14.Mufflerandenginebecomehotandcancauseaburn.Do

nottouch.

15.Onlyusepartsandaccessoriesmadeforthismachineby

theoriginalequipmentmanufacturer(O.E.M).Failureto

dosocanresultinpersonalinjury.

16.Ifsituationsoccurwhicharenotcoveredinthismanual,

usecareandgoodjudgment.Contactyourdealerfor

assistance.Telephone1-800-800-7310forthenameof

yournearestdealer.

SlopeOperation

Slopes are a major factor related to slip and fall accidents

which can result in severe injury. Operation on slopes

requires extra caution. If you feel uneasy on a slope, do not

mow it. Before operating this unit on a slope or hilly area, use

the slope gauge on page 6 to measure slopes. If the slope is

greater than 15 degrees, do not mow it.

Do:

1. Mow across the face of slopes; never up and down.

Exercise extreme caution when changing direction on

slopes.

2. Watch for holes, ruts, rocks, hidden objects, or bumps

which can cause you to slip or trip. Tall grass can hide

obstacles.

3. Always be sure of your footing. A slip and fall can cause

serious personal injury. If you feel you are losing your

balance, release the blade control handle immediately,

and the blade will stop rotating within 3 seconds.

DoNot:

1. Do not mow near drop-offs, ditches or embankments,

you could lose your footing or balance.

2. Do not mow slopes greater than 15 degrees as shown on

the slope gauge.

3. Do not mow on wet grass. Unstable footing could cause

slipping.

Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

mower and the mowing activity. They do not understand the

dangers. Never assume that children will remain where you

last saw them.

1. Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

2. Be alert and turn mower off if a child enters the area.

3. Before and while moving backwards, look behind and

down for small children.

4. Use extreme care when approaching blind corners,

doorways, shrubs, trees, or other objects that may

obscure your vision of a child or an adult who may run

into the lawn mower.

Keep children away from hot or running engines. They

can suffer burns from a hot muffler.

Never allow children under 14 years old to operate a

power mower. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and should be trained and

supervised by a parent.

Service

SafeHandlingOfGasoline:

1. To avoid personal injury or property damage use extreme

care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious

personal injury can occur when gasoline is spilled on

yourself or your clothes which can ignite.

2. Wash your skin and change clothes immediately.

3. Use only an approved gasoline container.

4. Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place containers on

the ground away from your vehicle before filling.

5. If possible, remove gas-powered equipment from the

truck or trailer and refuel it on the ground. Otherwise

refuel such equipment on a trailer with a portable

container rather than from a gasoline dispenser nozzle.

6. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

7. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

8. Never fuel machine indoors because flammable vapors

wilt accumulate in the area.

9. Never remove gas cap or add fuel while the engine is hot

or running. Allow engine to cool at least two minutes

before refueling.

10. Never over tilt fuel tank. Fill tank to no more than ½ inch

below bottom of filler neck to provide space for fuel

expansion.

11. Replace gasoline cap and tighten securely.

12. If gasoline is spilled, wipe it offthe engine and

equipment. Move unit to another area. Wait 5 minutes

before starting the engine.

13. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light as on a water

heater, space heater, furnace or other gas appliances.

14. To reduce fire hazard, keep mower free of grass, leaves,

or other debris build-up. Clean up oil or fuel spillage and

remove any fuel soaked debris.

15. Allow a mower to cool at least 5 minutes before storing.

GeneralService:

1. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless and deadly gas.

2. Before cleaning, repairing, or inspecting, make certain

the blade and all moving parts have stopped. Disconnect

the spark plug wire and ground against the engine to

prevent unintended starting.

3. Check the blade and engine mounting bolts at frequent

intervals for proper tightness. Also, visually inspect blade

fordamage(e.g.,bent,cracked,worn)Replaceblade

withtheoriginalequipmentmanufacture's(O.E.M.)blade

only,listedinthismanual."Useofpartswhichdonot

meettheoriginalequipmentspecificationsmayleadto

improperperformanceandcompromisesafetyF

4. Mowerbladesaresharpandcancut.Wrapthebladeor

weargloves,anduseextracautionwhenservicingthem.

5. Keepallnuts,bolts,andscrewstighttobesurethe

equipmentisinsafeworkingcondition.

6. Nevertamperwithsafetydevices.Checktheirproper

operationregularly.

7. Afterstrikingaforeignobject,stoptheengine,disconnect

thesparkplugwireandgroundagainsttheengine.

Thoroughlyinspectthemowerforanydamage.Repair

thedamagebeforestartingandoperatingthemower.

8. Neverattempttomakeawheelorcuttingheight

adjustmentwhiletheengineisrunning.

9. Grasscatchercomponents,dischargecover,andtrail

shieldaresubjecttowearanddamagewhichcould

exposemovingpartsorallowobjectstobethrown.For

safetyprotection,frequentlycheckcomponentsand

replaceimmediatelywithoriginalequipment

10.

11.

12.

manufacturer's(O.E.M.)partsonly,listedinthismanual.

"Useofpartswhichdonotmeettheoriginalequipment

specificationsmayleadtoimproperperformanceand

compromisesafetyF

Donotchangetheenginegovernorsettingoroverspeed

theengine.Thegovernorcontrolsthemaximumsafe

operatingspeedoftheengine.

Maintainorreplacesafetyandinstructionlabels,as

necessary.

Observeproperdisposaltawsandregulations.Improper

disposaloffluidsandmaterialscanharmthe

environment.

YourResponsibility

• Restrict the use of this power machine to persons

who read, understand and follow the warnings and

instructions in this manual and on the machine.

Some of the safety labels are reproduced below for

information purposes. Maintain safety by following

these labels.

/ WARNING

#AN 8R

USE THIS PAGE AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY.

.J..

SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE

I"If A POWER POLE

I'111 A CORNER OF A BUILDING

I I _ OR A FENCE POST

i I

"FOLD 0^,_ I

I ='_ ,v/.jO-

..... =,'_/_

15°

_ WARNING

--t

I-r1

I--

I-1"1

--I

Do not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10

feet). On steeper inclines, a riding mower could overturn and cause serious injury. If operating a walk-

behind mower on such a slope, it is extremely difficult to maintain your footing and you could slip, resulting

in serious injury. Operate RIDING mowers up and down slopes, never across the face of slopes.

SECTION3: ASSEMBLINGYOURLAWNMOWER

Unpacking

•Remove staples, break glue on top flaps, or cut

tape at carton end and peel along top flap to open

carton.

• Remove loose parts if included with unit (i.e.,

owner's manual, etc.).

• Cut along corners and lay carton down flat.

• Remove packing material.

• Roll or slide unit out of carton. Check carton

thoroughly for loose parts.

ToolsRequired

1. Pair of Pliers

2. Funnel

NOTE: This operator's manual covers various models

of lawn mowers. Follow only those instructions which

pertain to your unit.

BeforeAssembly

• Disconnect spark plug wire from the spark plug,

and ground it against the engine. See Figure 1.

• If engine is equipped with a rubber boot, attach

rubber boot to a bolt on the engine to ground.

AssemblingHandle

NOTE: Stand behind the mower as if you were going to

operate it. Your right hand corresponds to the right side

of the mower; your left hand corresponds to the left side

of the mower.

• Remove any packing material which may be

between the upper and lower handles.

• Pull up and back on the upper handle to raise the

handle into the operating position.

• Make certain the lower handle is seated securely

into the handle mounting brackets.

Tighten

hand knob

Tighten

hand knob

Spark Plug

Figure 1

HardwarePack

Please identify each piece of the hardware pack as

shown in Figure 2 here.

Wing Nut (2) Carriage Bolt (2)

Figure 2

Figure 3

• The upper handle is attached to the lower handle

with a handle knob and a carriage bolt on each

side. See Figure 3. Tighten these hand knobs.

Make sure that each carriage bolt is seated

properly on the handle.

• Locate hairpin clip in one hole on the weld pin on

each side of the lower handle. See Figure 4.

• Remove hairpin clip from this hole. Using a pair of

pliers, insert the hairpin clip into the other hole on

the weld pin. See Figure 4. Repeat on other side.

Carriage

Wing Nut

Hairpin

Weld

Figure 4

• Refer to the hardware pack in Figure 2. Insert the

carriage bolt from the hardware pack into the upper

hole on the handle mounting bracket. See Figure 4.

Secure with one plastic wing nut, also included in

the hardware pack. Repeat on the other side with

remaining items from the hardware pack.

• The rope guide is attached to the right side of the

upper handle. Loosen the wing nut which secures

the rope guide.

• Hold the blade control handle against the upper

handle, and pull the starter rope out of the engine.

Release the blade control handle. Slip the starter

rope into the rope guide. Tighten the wing nut. See

Figure 5.

• Tighten all nuts and bolts securely.

Slip rope into

rope g Wing Nut

Figure 5

Insert post on cable ties into holes provided on the

lower handle. Pull the cable tie tight and trim the

excess. See Figure 6.

Cable Tie

channels except center top of bag attach from the

outside of bag. Center top of bag attaches from the

inside of bag.

Center top of bag

Hook

Grass Bag Plastic Channel

Figure 7

NOTE: Once the grass bag has been attached to the

frame, the whole assembly is called a Grass Catcher.

AttachingGrassCatcher To Mower

• Lift the rear discharge door and place the grass

catcher on the pivot rod. Let go of discharge door

so that it rests on the grass catcher. See Figure 8.

Rear Discharge

Door \

Post

Hole on

Lower

Handle

Figure 6

AttachingGrassCatcher

NOTE: Make certain bag is turned right side out before

assembling (warning label will be on the outside).

Assembly

Grass Catcher Assembly consists of the following:

1. Frame Assembly

2. Grass bag

Follow steps below to assemble the grass catcher:

• Place bag over frame so that its black plastic side is

at the bottom. See Figure 7.

• Slip the plastic channel of the grass bag over the

hooks on the frame. See Figure 7. All of the plastic

Figure 8

RemovingGrassCatcherFrom Mower

• Lift the rear discharge door on the mower as shown

in Figure 8. Lift grass catcher up and out of the pivot

rod. Release rear discharge door.

Converting To Mulcher

• Lift the rear discharge door on the mower and

remove the grass catcher. Release the discharge

door to allow it to close the rear opening of the

mower. Now it is ready to mulch.

_ARNING: Never operate mower unless

the hooks on the grass catcher are firmly

seated in the slots on the handle bracket

assemblies, and the rear discharge door rests

firmly against top of the grass catcher.

AssemblingChuteDeflector(ifequipped)

If your mower is equipped with the optional chute

deflector, assemble as follows:

• Slide the rod into the upper edge of the chute

deflector so the tab on the rod is toward the left side

of the chute deflector. When assembled correctly,

the rod will extend further to the left side. See

Figure 9. Tab

Rod

Chute

Deflector

Figure 9

• Slide the push nut onto the right side of the rod to

secure.

AttachingChuteDeflectorTo Mower

•To attach chute deflector: Lift the rear discharge

door on the mower. Place the ends of the rod into

the slots in the handle bracket assemblies. See

Figure 10. Release the rear discharge door.

•To remove chute deflector: Lift the rear discharge

door on the mower. Lift the chute deflector up and

out of the slots in the handle bracket assemblies.

Release the rear discharge door. See Figure 10.

Rear

JDischarge

Door

Slots

Figure 10

IMPORTANT: This unit is shipped without gasoline or oil

in the engine. Be certain to service engine with gasoline

and oil before operating your mower.

SECTION4: KNOWYOURLAWNMOWER

Compare the illustrations in Figure 11 with your lawn mower to familiarize yourself with the location of various

controls and adjustments.

Blade Control Handle

Upper Handle

Recoil Starter

Grass Catcher

Bag-Fill Indicator (if equipped)

Lower Handle

Oil Fill/Dipstick

/-- Spark Plug

Gasoline Fill

Cutting Height Adjustment

Lever (Only two of four

are called out.)

Figure 11

BladeControlHandle

The blade control handle is located on the upper handle

of the mower. Depress it and squeeze against the

upper handle to operate the unit. Release the blade

control handle to stop the engine and blade.

_ARNING" The blade control mechanism isa safety device. Never attempt to bypass it.

RecoilStarter

The recoil starter handle is attached to the handle and

is used to start the engine.

CuttingHeightAdjustmentLever

These levers are located on each wheel and are used

to adjust the cutting height. All four levers have to be at

the same relative position to ensure uniform cut.

Bag-Fill Indicator(if equipped)

Some mowers are equipped with a bag-fill indicator on

the grass catcher to add convenience to your work. If

the grass catcher is empty, air flows through the

indicator and pushes the "sail" up. Ifthe grass catcher is

full, air does not flow through it and the "sail" falls. So

the position of the "sail" in the bag-fill indicator indicates

how full the grass bag is.

SECTION5: OPERATINGYOURLAWNMOWER

,_ WARNING: Keep hands and feet away

from the chute area on cutting deck. Refer to

warning label on the unit.

GasandOilFill-Up

• Service the engine with gasoline and oil as

instructed in the engine manual packed with your

mower. Read instructions carefully.

,_ WARNING" Never fill the fuel tank (i) indoors,

(ii) with engine running, or (iii) if engine has not

sufficiently cooled down. Wait at least two

minutes after stopping the engine.

BeforeStarting

• Attach spark plug wire to spark plug. Refer to

Figure 1. If the mower is equipped with a rubber

boot over the end of the spark plug wire, make sure

that metal cap inside the rubber boot is fastened

securely over the spark plug's metal tip.

ToStartEngine&EngageBlade

• Firmly push primer three times. See Figure 12A.

Push

release to

prime

ASqueeze these two B

handles

Pull

Recoil Starter

Figure 12

• Standing behind the lawn mower, squeeze the

blade control handle against the upper handle. See

Figure 12B.

• Holding both handles firmly, pull rope out slowly

from the recoil starter. See Figure 12C. Let the rope

rewind slowly. Repeat this motion till engine starts.

WARNING" The blade will be rotatingwhenever the engine is running. Keep your

hands and feet away from a rotating blade.

WARNING" Wait for the blade to stopcompletely before doing any work on the

mower or to remove the grass catcher.

ToStopEngine& Blade

• Release the blade control handle to stop the engine

and the cutting blade.

• Disconnect the spark plug wire and ground it

against the engine.

UsingRotaryMower

_ARNING: Never operate your mower

without either the rear door or the entire grass

catcher assembly firmly secured.

• Be sure that lawn is clear of stones, sticks, wire, or

other objects before starting to operate the mower.

,_ WARNING: If the mower strikes a foreign

object and/or vibrates excessively, stop the

engine. Remove spark plug wire, thoroughly

inspect for any damage, and repair the damage

before restarting.

• For best results, do not cut wet grass because it

tends to stick to the underside of the mower.

• For a healthy lawn, never cut more than one-third of

the total length of the grass at any one cutting.

NOTE: For shipping purposes your mower wheels are

set in a low cutting height position. Raise the cutting

height to a position best suited for your lawn. Refer to

page 12 for instructions.

Usingas Mulcher

For mulching grass, remove the grass catcher from the

mower. The rear discharge opening should be closed.

• For effective mulching, do not cut wet grass.

• New or thick grass may require a narrower cut. The

ground speed should be adjusted to the condition

of the lawn.

• Do not mulch if grass is taller than 4 inches. Use the

grass catcher to bag clippings instead.

BaggingGrassClippings

You can use the grass catcher to collect clippings while

you are operating the mower.

• Attach grass catcher following instructions on page

8. Grass clippings will automatically collect in the

bag as you run the mower. Operate the mower till

the grass bag is full. Refer to page 10 for

description of flow indicator, if so equipped.

• Stop engine completely by releasing the blade

control handle. Make sure that the unit has come to

a complete stop.

• Lift discharge door and pull grass bag up and away

from the mower to dispose of the grass clippings.

SECTION6: MAKINGADJUSTMENTS

_ARNING" Do not at any time make any

adjustment to lawn mower without first

stopping the engine and disconnecting the

spark plug wire.

HandleHeight

The mower is shipped with the handle at a higher height

position. To lower the handle height, proceed as

follows.

• Remove the starter rope from the rope guide.

• Remove the hand knobs, washers and carriage

bolts securing the upper handle to the lower

handle. Lay the upper handle out of the way, being

careful not to bend or kink the cables.

• Remove the hairpin clips from the weld pins on the

handle brackets. Press outward on the legs of the

lower handle, and remove it from the mower.

• Remove the carriage bolts and wing nuts from the

handle brackets. Press out on the legs of the lower

handle. Remove lower handle from the mower.

• Turn the lower handle around so the notches on the

bottom of the lower handle are facing forward as

shown in Figure 13.

• Place the bottom holes of the handle over the weld

pins in the handle mounting bracket. Reattach the

hardware.

Lower

Handle Notch

Figure 13

• Reassemble the upper handle.

• Place the hairpin clips in the inner holes of the weld

pins and replace the carriage bolts and wing nuts

on the handle brackets. Attach the starter rope as

instructed in the Assembly section.

CuttingHeight

An adjusting plate and thumb lever at each wheel

position provides cutting height adjustment. Each

adjusting plate has nine height positions.

• Simply depress the lever towards wheel and move

it to any of the nine positions for the desired cutting

height. See Figure 14. All four levers on the four

wheels must be placed in the same relative position

for uniform cutting height

Height

Adjustment

JLever

Figure 14

Carburetor

Minor carburetor adjustments may be required to

compensate for differences in fuel, temperature,

altitude and load. To adjust carburetor, refer to the

engine manual.

NOTE: A dirty air cleaner will cause an engine to run

rough. Be certain air cleaner is clean and attached to

the carburetor before adjusting carburetor.

,_ WARNING: If any adjustments are made tothe engine while the engine is running (e.g.

carburetor), keep clear of all moving parts. Be

careful of heated surfaces and muffler.

SECTION7:

_ ARNING" Be sure to disconnect and

ground the spark plug wire before performing

any repairs or maintenance.

MaintainingtheBlade

• Periodically inspect the blade adapter for cracks,

especially if the mower strikes a foreign object.

Replace blade if crack or any damage is found.

MAINTAININGYOURLAWNMOWER

BladeMountingTorque:

Center Bolt: 450 in. Ibs. min., 600 in. Ibs. max.

IMPORTANT: To ensure safe operation of your unit,

periodically check all nuts and bolts and tighten if

necessary.

_i WARNING" When removing the cutting

blade for sharpening or replacement, protect

hands by using heavy gloves or a rag to grasp

the cutting blade.

Remove the bolt and bell support which hold the

blade and adapter to the engine crankshaft. See

Figure 14. Remove the blade and adapter from the

crankshaft.

DeckCare

NOTE: We do not recommend the use of pressure

washers or garden hose to clean your unit. These may

cause damage to electric components, spindles,

pulleys, bearings or the engine. Use of water will

shorten life of the mower and reduce its serviceability.

Tilt the mower and scrape underside of the deck

after each use to remove grass clippings, leaves or

dirt. If this debris is allowed to accumulate, the deck

may start to rust.

Crankshaft

Blade

Adapter

. Bell

Support

Hex Bolt

Figure 15

• When sharpening the blade, follow the original

angle of grind. Grind each cutting edge equally to

keep the blade balanced. An unbalanced blade will

cause excessive vibration when rotating at high

speed. This may damage the mower and/or cause

personal injury.

• The blade can be tested by balancing it on a round

shaft screwdriver. Always remove blade from the

adapter for testing balance. Remove metal from the

heavy side until it balances evenly.

• Before reassembling the blade and the blade

adapter to the unit, lubricate the engine crankshaft

and the inner surface of the blade adapter with light

oil (or engine oil). Also lubricate the bolt holes, bolts

and inner surface of the nuts.

• Install the blade adapter on the crankshaft with the

"star" away from the engine. Place the blade with

the side marked bottom (or with part number) facing

away from the adapter. Align the blade bell support

over the blade with tabs in the holes of the blade

and insert the hex bolt. Tighten the hex bolt to the

torque listed here.

ReplacingRearFlap

• To remove rear flap, cut off the flat end of the wire

rod which secures it to the deck. See Figure 16.

• Attach the new flap and new rod to deck, bending

the ends of the new rod over to secure to deck.

DoorRearDischarge __

Handle __

Bracket

\,\

Rear

Flap

Figure 16

Engine

A list of key engine maintenance jobs required for good

performance by the mower is given below. Follow the

accompanying engine manual for detailed list and

instructions.

Maintain engine oil level as instructed in engine

manual.

Service air cleaner every 25 hours under normal

conditions. Clean every few hours under extremely

dusty conditions. Poor engine performance and

flooding usually indicates that the air cleaner should

be serviced. To service the air cleaner, refer to the

engine manual.

• Clean spark plug and reset the gap once a season.

Spark plug replacement is recommended at the

start of each mowing season. Check engine

manual for correct plug type and gap specifications.

• Clean engine regularly with a cloth or brush. Keep

the cooling system (blower housing area) clean to

permit proper air circulation. Remove all grass, dirt

and combustible debris from muffler area.

Lubrication

Figure 17: Lubrication Chart

BladeControl

Lubricate the pivot points on the blade control handle

and the brake cable at least once a season with light oil.

See Figure 17. The blade control must operate freely in

both directions.

RearDischargeDoor

The torsion springs and pivot points should be

lubricated periodically with light oil to prevent any rust

or binding. The discharge door must work freely.

Wheels

Wheels require no lubrication. However, if the wheels

are removed for any reason, lubricate the surface of the

axle bolt and the inner surface of the wheel with light oil.

Engine oil may also be used.

Engine

Follow engine manual for lubrication instructions.

Off-SeasonStorage

If the lawn mower is not going to be used for 30 days or

longer, prepare the unit for storage. Follow the steps

below for proper storage of the mower.

• Clean and lubricate mower thoroughly as described

in the lubrication instructions.

• Refer to engine manual for correct engine storage

instructions.

• Coat mower's cutting blade with chassis grease to

prevent rusting.

• Store mower in a dry, clean area. Do not store next

to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in

an unventilated or metal storage shed, care should be

taken to rust-proof the equipment. Using a light oil or

silicone, coat the equipment, especially cables and all

moving parts.

SECTION8: TROUBLESHOOTINGGUIDE

Possible Cause(s) Corrective Actions

Trouble

Engine fails to

start

Engine runs

erratic

Engine

overheats

Occasionally

skips at high

speed

Idles poorly

Excessive

vibration

Mower witt not

mulch grass

1. Blade control handle disengaged.

2. Spark plug wire disconnected.

3. Dirty aircteaner.

4. Primer button not depressed.

5. Throttle control lever (if so equipped) not in

correct starting position.

6. Fuel tank empty or stale fuel.

7. Blocked fuel line

8. Faulty spark plug.

9. Engine flooded.

1. Spark plug wire loose.

2. Blocked fuel line, if equipped, or stale fuel.

3. Vent in gas cap plugged.

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Carburetor out of adjustment.

1. Engine oil level tow.

2. Dirty aircleaner.

3. Air flow restricted.

Carburetor not adjusted properly.

Spark plug gap too close.

Carburetor idle mixture adjustment

improperly set.

1. Spark plug fouled, faulty or gap too wide.

2. Carburetor improperly adjusted.

3. Dirty air cleaner.

1. Cutting blade loose or unbalanced.

2. Bent cutting blade.

1. Wet grass.

2. Excessively high grass.

1. Engage blade control handle.

2. Connect wire to spark plug.

3. Refer to the engine manual.

4. Refer to the engine manual.

5. Move throttle lever to FAST or START position.

6. Fill tank with clean fresh gasoline.

7. Clean fuel line.

8. Clean, adjust gap or replace.

9. Refer to the engine manual.

1. Connect and tighten spark plug wire.

2. Clean fuel line; fill tank with clean, fresh gasoline.

3. Clear vent or threads or replace.

4. Drain fuel tank. Refill with fresh fuel.

5. Refer to the engine manual.

6. Refer to the engine manual.

1. Fill crankcase with proper oil.

2. Refer to the engine manual.

3. Stop engine and disconnect spark plug wire.

Remove blower housing and clean.

4. Refer to the engine manual.

1. Adjust gap to .030".

2. Refer to the engine manual packed with your unit.

1. Reset gap to .030" or replace spark plug.

2. Refer to the engine manual.

3. Refer to the engine manual.

1. Tighten blade and adapter. Balance blade.

2. See an authorized service dealer.

Do not mow when grass is wet; wait until later to cut.

Mow once at a high cutting height, then mow again

at desired height or make a narrower cutting swath

(1/2 width).

Uneven cut 1. Wheels not positioned correctly. 1. Place all four wheels in same height position.

2. Dull blade. 2. Sharpen or replace blade.

NOTE: For repairs beyond those listed above, contact an authorized service dealer or call 1(800)800-7310.

SECTION9: PARTSLISTFORMODELSERIES410THROUGH419

11 lo_. /2

Zag Tread Wheel

Bar Tread Wheel

\54

ModelSeries410Through419

Ref. Part No.

No.

1. 747-1161A

2. 749-1092A

3. 747-04080

7. 749-0928A

8. 720-0279

9. 710-1205

10. 710-1174

11. 664-04005

764-0650

12. 720-0284

13. 736-0451

14. 726-0240

15. 710-0703

16. 731-04134

17. 750-04162

18. 732-04089

732-04090

19. 787-01144

787-01143

20. $

21. 782-5003

22. 731-0981A

23. 787-01103

24. 710-1017

25. 782-5002A

26. 748-0376C

27. 742-0741

28. 710-1044

29. 736-0524A

30. 15261A

31. 687-02077

687-02077

687-02076

32. 720-0426

Description

Blade Control Handle

Upper Handle

Grass Catcher Frame

Lower Handle

Wing Nut

Rope Guide

Carriage Bolt 5/16-18 x 2

Grass Bag Assembly

Grass Bag Assembly w/Bag-Fill Ind .-[

Ref.

No.

33.

34.

36.

38.

39.

40.

Part No.

732-0404

738-0507B

782-5004A

746-0957

746-1130

746-0554

746-1137

720-0295

Description

Spring Lever Assembly

Shoulder Screw

Front Wheel

Rear Baffle RH

Control Cable 37.25"

Control Cable 40"

Control Cable 40.5"

Control Cable 53"

Foam Grip 1 (not shown)

Hand Knob

Saddle Washer

Cable Tie

Carriage Bolt 1/4-20

Rear Discharge Door

Spacer

Torsion Spring LH

Torsion Spring RH

Handle Bracket RH

Handle Bracket LH

Rear Wheel

Rear Baffle LH

Hubcap 1-

Cutting Deck: Rear Discharge

AB Screw 1/4-14 x .625"

Front Baffle

Blade Adapter

Mulching Blade

Hex Bolt 3/8-24 x 1.5

Blade Belt Support

Front Adjustment Plate

Pivot Arm Assembly RH (8" wheel)

Pivot Arm Assembly LH (7" wheel)

Pivot Arm Assembly LH (8" wheel)

Pivot Arm Assembly RH (7" wheel)

Knob: Adjustment Lever

41. 731-1236

42. 732-0700

43. 731-1506

44. 712-0397

45. 710-0654A

46. 687-02071

687-02070

47. 787-01132

787-01131

48. 710-1652

49. 712-0431

50. 714-0104

51. 710-0654A

52. 687-02074

687-02100

687-02075

687-02099

53. 687-02069

687-02068

54. 712-0431

55. 747-04035

56. 736-0504

57. 731-1405

58. 711-0996

59. 726-0201

60. 750-0535

Traitshield

Trailshield Wire

Deck: Front Cover 1-

Wing Nut 1/4-20

Hex L-Washer Hd. Screw 3/8-16 x 1.0

Lever Assembly: Rear Height Adj. RH

Lever Assembly: Rear Height Adj. LH

Pivot Bar: 9 Position RH

Pivot Bar: 9 Position LH

AB Screw

Flange Lock Nut 3/8-16

Hairpin Clip

TT Sems Screw 3/8-16 x 1.0

Ht. Adj. Assy. Front RH (8" Wheel)

Ht. Adj. Assy. Front RH (7" Wheel)

Ht. Adj. Assy. Front LH (8" Wheel)

Ht. Adj. Assy. Front LH (7" Wheel)

Handle Bracket Assy. Rear LH

Handle Bracket Assy. Rear RH

Flange Nut 3/8-16 Thd.

Pivot Rod: Rear Door

Wave Washer 1-

Chute Deflector 1-

Rod 1-

Push Speed Nut1-

Spacer 1-

IIf equipped

:1:Refer to Wheel Chart

_Wheel Chart

Type

Wheels w/o bearing

Wheels w/BB

Part No.

734-1781, Slot Hub

734-1987, 8 x 1.8

734-1988, 7 x 1.8

634-0020, Disc Hub

734-2004A, Disc Hub

734-2005A

Tread

Bar

Zag

YOURNOTES

Date Comments

YOURNOTES

Date Comments

MANUFACTURER'S LIMITED WARRANTY FOR:

The limited warranty set forth below is given by MTD LLC with

respect to new merchandise purchased and used in the

United States, its possessions and territories.

"MTD"warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and wilt, at its option, repair or

replace, free of charge, any part found to be defective in

materials or workmanship. This limited warranty shall only

apply if this product has been operated and maintained in

accordance with the Operator's Manual furnished with the

product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water, or damage because of

other peril or natural disaster. Damage resulting from the

installation or use of any part, accessory or attachment not

approved by MTD for use with the product(s) covered by this

manual will void your warranty as to any resulting damage.

Normal wear parts or components thereof are subject to

separate terms as follows: All normal wear parts or

component failures wilt be covered on the product for a period

of 30 days regardless of cause. After 30 days, but within the

two year period, normal wear part failures will be covered

ONLY IF caused by defects in materials or workmanship of

OTHER component parts. Normal wear parts and

components include, but are not limited to: batteries, belts,

blades, blade adapters, grass bags, rider deck wheels, seats,

snow thrower skid shoes, shave plates, auger spiral rubber,

and tires.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE, through your local authorized

service dealer. To locate the dealer in your area, check your

Yellow Pages, or contact MTD LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-

330-220-4683 or tog on to our Web site at

www.mtdproducts.com.

This limited warranty does not provide coverage in the

following cases:

The engine or component parts thereof. These items

may carry a separate manufacturer's warranty. Refer

to applicable manufacturer's warranty for terms and

conditions.

Log splitter pumps, valves, and cylinders have a

separate one year warranty.

Routine maintenance items such as lubricants, filters,

blade sharpening, tune-ups, brake adjustments, clutch

adjustments, deck adjustments, and normal

deterioration of the exterior finish due to use or

exposu_.

MTD does not extend any warranty for products sold or

exported outside of the United States, its possessions

and territories, except those sold through MTD's

authorized channels of export distribution.

Replacement parts that are not genuine MTD parts.

Service completed by someone other than an

authorized service dealer.

Transportation charges and service calls.

No implied warranty, including any implied warranty of

merchantability of fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty, whether written or oral, except as

mentioned above, given by any person or entity,

including a dealer or retailer, with respect to any product,

shall bind MTD. During the period of the warranty, the

exclusive remedy is repair or replacement of the product

as set forth above.

The provisions as set forth in this warranty provide the

sole and exclusive remedy arising from the sale. MTD

shall not be liable for incidental or consequential loss or

damage including, without limitation, expenses incurred

for substitute or replacement lawn care services or for

rental expenses to temporarily replace a warranted

product.

Some states do not allow the exclusion or limitation of

incidental or consequential damages, or limitations on how

long an implied warranty lasts, so the above exclusions or

limitations may not apply to you.

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration

of safety features of the product shall void this warranty.

You assume the risk and liability for toss, damage, or injury to

you and your property and/or to others and their property

arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser or to the person for whom it was purchased

as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This

limited warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

IMPORTANT:Owner must present Original Proof of

Purchase to obtain warranty coverage.

MTD LLC, P.O.BOX361131CLEVELAND,OHIO44136-0019; Phone:1-800-800-7310,1-330-220-4683

MTD 11A 414E700 User Manual LAWN MOWER Manuals And Guides 1108461L

Navigation menu

Versions of this User Manual:

Views

Navigation