Midland Radio 700671A VHF Transceiver User Manual

Midland Radio Corporation VHF Transceiver CONTENTS

UserManual.wiki >

a href="https://usermanual.wiki/Midland-Radio" itemprop="url"> Midland Radio >

700671A User Manual >

revised manual ⚡ Mobile Version

revised manual

SERVICE MANUALSTesting, alignment and service information are provided in the servicemanual for this model. Service manuals for Titan™ radios areavailable from Midland Radio Corporation at the address shown onthe back cover.7DO NOT transmit more than 50% of total radio use time (50% dutycycle). Transmitting for more than 50% of the time can cause FCCRF exposure compliance requirements to be exceeded. This radio istransmitting whenever the TX icon is displayed on the LCD. Pressingthe PTT switch on the side of the microphone normally causes theradio to transmit. Note: The preceding information is provided to make youaware of RF exposure and how to ensure that this radio isoperated within FCC RF exposure limits.You, as the qualified end-user of this radio device must control theexposure conditions of bystanders to ensure the minimum separationdistance, stated above for satisfying FCC RF exposure compliance, ismaintained between the antenna and nearby persons. Transmit onlywhen all person(s) are at least the minimum distance from theproperly installed, externally mounted antenna.IMPORTANT SAFETY INFORMATIONCAUTIONSa The antenna connector must be snugly tightened to maintainproper electrical connection and moisture resistance.a Equipment must be grounded according to Midland RadioCorporation installation instructions for safe operation.a Equipment should be serviced only by a qualified technician.a Refer to radio service manual for additional information oninstallation and safety precautions.WARNING!! DO NOT allow the antenna to touch or come in very closeproximity with the eyes, face, or any exposed body parts while theradio is transmitting! DO NOT operate the radio in explosive or flammableatmospheres. The transmitted radio energy could trigger blastingcaps or cause an explosion.! DO NOT allow children to operate or play with this radio. Note: The above warning list is not intended to include allhazards that may be encountered when using this radio.ii

CONTROLS AND INDICATORSPOWER/VOLUME KNOBPress and hold for a few seconds for power on. Press andhold again for power off. Clockwise rotation increasesvolume of received messages.CHANNEL/MENU CONTROL KNOBChannel Function: Rotate to scroll throughchannels. Your radio can be programmed, by theradio technician to either stop at the highest andlowest channels, or for channel rollover.Menu Function: Press and release to activate themenu mode, which will allow you to access, SquelchSetting (SQL), Group Setting (GRP), All Group Scan(AGS) or One Group Scan (OGS), Scan Key TypeSetting (PRI, SCN, P/S), Back Light Control (BLN=on, or BLF=off), ANI (ANN=on, ANF=off), Clone Mode(CLN) and Clone Process. When finished adjusting the squelch, immediatelypress the MENU button to cause the new squelchsetting to be stored in the radio memory. For properoperation the squelch should be set 5 – 10 digitshigher than the level required for initial muting. All Group Scan availability requires more than 1group to be programmed and Type A scan selected.Some scan key types may not be availabledepending on programming. The ANI mode will notbe available unless activated by the radio technician.PUSH-TO-TALK BAR (On the Hand Microphone)Transmit mode (talk mode) is initiated when pressed.The radio will emit your voice signals on the channelthat appears in the Channel Display.SCAN BUTTONPress SCAN to activate Scan operation. For detailedinformation see the following descriptions of thedifferent scan modes. Also used in conjunction withthe A/D button to add or delete channels from thescan list.1PRIORITY SCAN ESCAPEIf the radio technician has programmed the radio for this function, theoperator may press the “AUX” button to operate on the last busychannel. Press the “AUX” button again to revert to priority scan withthe priority channel unchanged.NOTE: Conditions when the scan table is automatically reset(initialized), to original programming, is set by the radio technician.The user may manually initialize the scan table by pressing the A/Dbutton for a few seconds (until 2nd beep) when not in scan operation.ANI OPERATION1. If ANI operation has been activated during initial programming theradio will transmit the code on the first transmission of aconversation.2. If the ANI is activated on a certain channel by the radio technician,it cannot be deactivated by the user. The ANI may be set on/off bythe user if it is not specifically activated by the technician.2 TONE DECODE OPERATION1. If the radio is programmed for 2 tone decode it may be activated,on channels so programmed, by pressing and holding the menubutton until the second beep is heard.2. When the radio receives a call with the proper ANI code a seriesof quick beeps will be heard. If the call is answered by pressingthe PTT then the decoder will be reset to normal (non ANI)operation. If the call is not answered a beep will be heard 15seconds and 30 seconds after the call and then return to ANIdecode mode.3. The decoder may be also be deactivated by pressing the MONbutton or the PTT button.6SCAN

4. PRI monitor function is not available in this mode. If scan isstopped, Add/Delete of Group B channels is available inAdd/Delete mode.5. Other operation is the same as type “A” scan.TYPE “B’ ” SCAN MODE1. Operation is the same as type “B” scan, except the SCAN buttonoperation is the same as type “A” scan.2. If scan is stopped, Add/Delete of Group B channels is available inAdd/Delete mode.TYPE “PS” SCAN MODE1. The “A” channels will be scanned in this mode.2. The transmit priority and priority monitoring channel will be thechannel that was set when scan was activated.3. To change the “PRI 1” channel, rotate the channel selector whilein the scan mode or during OFF HOOK SCAN stop.4. Deleting a nuisance channel is the same as type “A” scan.5. Adding or deleting the “PRI 2” channel is the same as type “A”scan.6. If scan is stopped, Add/Delete of Group A channels is availablein Add/Delete mode.TYPE “GRP A” MODE1. Transmit will occur on the currently displayed channel. 2. To change the LAST HOLD CHANNEL rotate the channel selectorduring scan.3. It is not possible to add or delete scan channels.4. Channel returns to the LAST HOLD CHANNEL, when scan isstopped by the operator.5. Other operation is the same as type “A” scanTYPE “S CH” MODE 1. If the radio is stopped scanning on the “PRI 1” or “PRI 2” thentransmit will occur on the corresponding “PRI” channel.2. It is not possible to add or delete scan channels in this mode.Other operation is the same as type “A” scan. 5MONITOR BUTTONPress and immediately release the MON button todisable the receive Coded Squelch function foradjustment of squelch and volume and to check forbusy channel. Press and release again to re-enablethe coded squelch. In case the MON button is heldmore than 1 second the MON button must be heldagain more than 1 second to release the monitormode.A/D BUTTONPress A/D to activate Add/Delete Mode. For detailedinformation see the following description of scanoperation.AUX BUTTONPress AUX to access Auxiliary functionsCHANNEL DISPLAYIndicates selected channel number and is alwaysilluminated when radio is on. During scan operation,indicates selected channel or received channel. DISPATCH OPERATIONSELECTING CHANNELSIf your radio is equipped with more than one channel, rotate thechannel knob to select available channels. Consult your dispatcher forproper usage.MESSAGE RECEIPT (RECEIVE)If a signal exists on the displayed Channel, and you are within radiorange of the sender, you will hear it on the loudspeaker.NOTE: Your radio may be equipped to block communications fromradios not in your radio system (coded squelch feature), or it mayeven block calls from your system that are not directed to you (selectcall feature). 2I20A/DAUXMON

Download:
Mirror Download [FCC.gov]
Document ID	348722
Application ID	/+KHrkNOTNjZHXCJXmvsZA==
Document Description	revised manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.98kB (74731 bits)
Date Submitted	2003-05-15 00:00:00
Date Available	2003-02-21 00:00:00
Creation Date	2003-08-14 17:05:21
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2003-08-14 17:09:12
Document Title	CONTENTS
Document Creator	Acrobat PDFMaker 6.0 for Word
Document Author:	SW Engineering

FCC ID Filing: MMA700671A

Navigation menu