Mikrotikls SIA RB951-2N BROADBAND DIGITAL TRANSMISSION SYSTEM User Manual

Mikrotikls SIA BROADBAND DIGITAL TRANSMISSION SYSTEM Users Manual

a href="https://usermanual.wiki/Mikrotikls-SIA" itemprop="url"> Mikrotikls SIA >

Users Manual

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 7-May-2012 RouterBOARD 951-2n Quick Setup Guide and Warranty Information Connecting 1. Connect your WAN cable to port 1, and LAN PCs to ports 2-5 2. Set LAN computer IP configuration to automatic (DHCP) 3. Default IP address from LAN/WLAN is 192.168.88.1, open this address in your web browser to start configuration. The username is admin and there is no password (Alternatives are SSH, Telnet or Winbox tool) 4. Wireless AP mode is enabled by default, you can connect to the SSID “MikroTik”. Log into your router and configure a WPA password to secure your network Powering The device accepts powering from the power jack or from the first ethernet port (Passive PoE):  DC power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts 8-30V DC  The first ethernet port accepts passive Power over Ethernet accepts 8-30V DC Under maximum load, the power consumption of this device is 7W Booting process RouterOS is the operating system of all RouterBOARD routers. Please see detailed configuration guide here http://wiki.mikrotik.com/wiki/Category:Manual This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username admin and no password. In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of the device when starting it until the LED light turns off, and Groove will start to look for Netinstall servers. In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup Extension Slots and Ports  Five individual 10/100 Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network devices. The First Ethernet port accepts 8-30V DC powering from a passive PoE injector.  One Integrated Wireless 2.4GHz 802.11b/g/n, 1x1 MIMO with two onboard PIF antennas, max gain 1.5dBi  One USB 2.0 port
See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 7-May-2012 Buttons and Jumpers  RouterOS reset jumper hole (on the bottom of case, behind one of the rubber feet) – resets RouterOS software to defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place until RouterOS configuration is cleared.  RouterBOOT reset button (RESET, front panel) has two functions: o Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (same result as with RouterOS reset hole) o Hold this button during boot time longer, until LED turns off, then release it to make the RouterBOARD look for Netinstall servers. Operating System Support Currently tested operating system is MikroTik RouterOS starting from version v5.15 Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective holders. Hardware. MikroTik warrants all RouterBOARD series equipment for the term of fifteen (15) months from the shipping date to be free of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature. To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. 1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik in Latvia. 2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000 series. 3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the sender at sender's cost. RMA Instructions are located on our webpage here: http://rma.mikrotik.com Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to ensure the accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. Please report any inaccuracies found to support@mikrotik.com
Download:
Mirror Download [FCC.gov]
Document ID1696010
Application IDDlB3ZGlNdPbWmpDXAJlgJg==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize39.58kB (494758 bits)
Date Submitted2012-05-11 00:00:00
Date Available2012-05-11 00:00:00
Creation Date2012-05-09 08:48:01
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2012-05-09 08:48:01
Document TitleUsers Manual
Document CreatorMicrosoft® Word 2010
Document Author: Normis
FCC ID Filing: TV7RB951-2N

Navigation menu