Mikrotikls SIA RBMAP2ND Digital Transmission System 2412-2462 MHz User Manual

Mikrotikls SIA Digital Transmission System 2412-2462 MHz Users Manual

a href="https://usermanual.wiki/Mikrotikls-SIA" itemprop="url"> Mikrotikls SIA >

Users Manual

RouterBOARD mAPQuick Setup Guide and Warranty InformationThe mAP is a small AP device with 2 ethernet ports, Ether1 supports powering by PoE, ether 2supports PoE output for powering another device.Connecting1. Connect your Internet cable to port 1, and your PC to port 2. If using the mAP to poweranother router using the PoE output feature, connect the router to Ether 2, and use the built inwireless AP to configure the mAP2. Set computer/router IP configuration to automatic (DHCP)3. Wireless AP mode is enabled by default, you can connect to the SSID “MikroTik”. Log into yourrouter from your web browser by opening 192.168.88.1 in the address bar4. The Ether 2 port suports PoE output, with auto detection feature. This means you can connectLaptops and other non-PoE devices without damaging them. The PoE on Ether2 outputsapproximately 2V below input voltage, and supports up to 0.5A (So provided 24V PSU willprovide 22V/0.5A output to the Ether2 PoE port). PoweringThe device accepts powering from the power jack or from the first Ethernet port (Passive PoE):DC power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts 8-57V DCThe first Ethernet port accepts 802.3af/at and passive Power over Ethernet accepts 8-57V DC.Some Gigabit PoE output devices might require crossover cable to power this devicemAP can also be powered with the built in microUSB port, using the USB 5V powerUnder maximum load, the power consumption of this device is 4W (when not using PoE output)Booting processThe device is preinstalled with MikroTik RouterOS software. It can be configured in several ways.This device doesn't come fitted with a Serial Port connector, so initial connection has to be done viathe Ethernet cable. Connect to wireless SSID “MikroTik” and open 192.168.88.1 in your webbrowser. Username is admin and there is no password. In case IP connection is not available, Winboxcan be used to connect to the MAC address of the device. More information here:http://wiki.mikrotik.com/wiki/First_time_startupIn case you wish to boot the device from network, for example to use MikroTik Netinstall, hold theRESET button of the device when starting it until the LED light turns off, and Metal will start to lookfor Netinstall servers.In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold theRESET button of the device when starting it until the LED light turns off, then release the button andthe device will start looking for Netinstall servers. 
By default, the device is preconfigured with a simple firewall on the WAN port, this configuration canbe viewed when first connecting to the Router via Winbox. It will ask whether to keep thisconfiguration or clean it to use your own. LAN/WLAN ports have DHCP server enabled.Extension Slots and PortsTwo 10/100 Ethernet ports, supporting automatic cross/straight cable connection (AutoMDI/X), so you can use either straight or cross-over cables for connecting to other networkdevices. One Integrated Wireless 2.4GHz 802.11b/g/n 2x2 MIMO, Onboard PIF antennas, max gain1.2dBiOne microUSB 2.0 portResetting the deviceIn case you wish to return the device to its original configuration, you can use the RESET buttonwhich is located to the left of the Ethernet ports. Hold this button during boot time until LED lightsstart flashing, then release the button to reset RouterOS configuration. You can use this procedureif you have forgotten the password to access the device, or simply wish to return the unit to itsdefault configuration state.Buttons and JumpersRouterOS reset jumper hole (on the bottom of case, behind one of the rubber feet) – resetsRouterOS software to defaults. Must short circuit the metallic sides of the hole (with ascrewdriver, for example) and boot the device. Hold screwdriver in place until RouterOSconfiguration is cleared. RouterBOOT reset button (RESET, front panel) has two functions:Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (same result as with RouterOS resethole)Hold this button during boot time longer, until LED turns off, then release it to make the RouterBOARD look for Netinstall servers.Operating System SupportCurrently tested operating system is MikroTik RouterOS starting from version 6.7Copyright and Warranty informationCopyright MikroTikls SIA. This document contains information protected by copyright law. No part of itmay be reproduced or transmitted in any form without prior written permission from the copyrightholder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. Alltrademarks and registered trademarks appearing in this document are the property of their respectiveholders.Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) monthsfrom the shipping date to be free of defects in materials and workmanship under normal use andservice, except in case of damage caused by mechanical, electrical or other accidental or intendeddamages caused by improper use or due to wind, rain, fire or other acts of nature.To return failed units to MikroTik, you must perform the following RMA (Return MerchandiseAuthorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improvethe speed of the RMA process. 
Download:
Mirror Download [FCC.gov]
Document ID2864314
Application IDYnip2UGf2hTM4lsyedTe7g==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize27.07kB (338342 bits)
Date Submitted2016-01-06 00:00:00
Date Available2016-01-06 00:00:00
Creation Date2015-12-10 14:02:40
Producing SoftwareLibreOffice 4.2
Document Lastmod0000-00-00 00:00:00
Document TitleUsers Manual
Document CreatorWriter
Document Author: Normis
FCC ID Filing: TV7RBMAP2ND

Navigation menu