Miller Edge MTF10 RF Link User Manual AW12 RF Prelimx

Download:
Mirror Download [FCC.gov]
Document ID	2302187
Application ID	DIUuFkmJc9jL8Winse2h6g==
Document Description	aw12 manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.12kB (138985 bits)
Date Submitted	2014-06-20 00:00:00
Date Available	2014-06-23 00:00:00
Creation Date	2014-05-28 14:53:39
Producing Software	Nitro PDF PrimoPDF
Document Lastmod	2014-05-28 14:53:39
Document Title	Microsoft Word - AW12-RF Prelim.docx
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	DanielL

AW12-RF/MRF-01 INSTALLATION INSTRUCTIONS
Preliminary
1- PARTS LIST
PART NUMBERS
-AW12-RF Single Channel
Transmitter/Air Wave™ Switch
Assembly
-MRF-01 Single Channel Receiver
-P/N=? Battery, CR2032
-(4) #6-20x3/4”, Screw, Self-Drilling
2- INSTALL TRANSMITTER/AIR
WAVE™SWITCH ASSY
-Open box, unpack battery and remove
lid from the AW12-RF.
-Install CR2032 battery as shown with
the “+” side up. Notice that the Red LED
blinks once upon insertion.
-Now position & attach, with provided
screws, your AW12-RF to your bottom
angle or end stile of your door. Replace
lid.
-Now, dependent upon your “kit”, make
the necessary airline connections.
3- INSTALL RECEIVER
-Open box, remove lid from the MRF-01
receiver.
-Position receiver on operator, so that
its wiring will reach the operator
terminal strip. Keep in mind that the
Green antenna wire must be exposed to
the AW12-RF Transmitter/Air Wave™
Switch. It cannot be behind any type of
metal.
-Connect the Red (+) & Black (-) to your
24VAC/DC source. The White wire
connects to a low voltage COMMON
terminal. The Yellow wire connects to
your EDGE/SAFETY terminal.
4- PROGRAMMING
-Apply power to the receiver.
-Green Power LED stays on; Channel 1
Red LED will be blinking.
-To enter “Learn” mode simply press
your fingertip onto CH1 (in the LEARN
BUTTON section of the PCB). The Red
LED remains on and the Amber Learn
LED will begin to blink.
-Activate the edge & note the Red &
Amber LED’s will blink alternately
rapidly. Then the Red LED will go out &
the Amber LED remains on.
-Channel 1 is now programmed.
-To start-over/erase programming,
press and hold CH1 again for 3 seconds,
LED’s will blink for 5 seconds & then go
into fault mode.
5- TEST SAFETY EDGE
-Ensure that your door stops/reverses
when safety edge is activated during
close cycle.
LED INDICATORS
LED
Color
Green
Yellow
Function
Description
Power
Status
Red
(per
channel)
Relay
State
Always On
Usually On – Off if right
out of the box, no
transmitter associated.
Wink Off once per TX
message received.
Blinks rapidly during
Learn Mode.
Off when Relay is
Clear.
On when Relay is in
Fault.
Blink very slowly for
Low Battery.
Blink slowly if no TX
has been associated.
On when this channel
is in Learn Mode
(Yellow blinking).
Blinks rapidly when
Learn Mode is
complete.
Learn
Mode
5- Specifications and Controls: Transmitter Unit
Frequency: 915 MHz. FSK Modulation.
Indicator Lights: Red LED: Tx Data
Power Source: Batteries: CR2032 Coincell. 3.0VDC Lithium.
Dimensions:
Antenna: Integral PCB loop.
Response Time: Nominal 70 msec; Safety Edge Input to Receiver Relay Contact Output.
6-Specifications and Controls: Receiver Unit
Indicator Lights: Green LED: Power on; Red LED: Relay energized, indicates safety edge activation;
Yellow LED: Status
Power Source: 10 to 40 VDC, 10-30 VAC (RMS)
Power Consumption: 16 mA (Idle) with Relay Off; 53 mA (avg.) with Relay On
Dimensions: 4.9”w x 3.75”h x 1.2”d
Cable Connections: Integral 18” wiring with #8 spade lugs.
Maximum Operating Distance: 100 Feet
7- FCC Compliance
FCC ID: OYE-MTF10
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS.
1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
AND
2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which may be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1- Re-orient or relocate the receiver antenna
2- Increase the separation between the equipment and the receiver
3- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4- Consult the dealer or an experienced radio/TVtechnician for help.
Changes or Modifications Not Expressly Approved By The Party Responsible For Compliance Could Void The User’s
Authority To Operate The Equipment.
P.O. Box 159 • West Grove, PA 19390 • 800-220-3343 • 610-869-4422 • Fax: 610-869-4423 • www.milleredge.com
6809 South Harl Ave., Suite A • Tempe, AZ 85283 • 800-887-3343 • 480-755-3565 • Fax: 480-755-3558

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 4
Producer                        : Nitro PDF PrimoPDF
Create Date                     : 2014:05:28 14:53:39+04:00
Modify Date                     : 2014:05:28 14:53:39+04:00
Title                           : Microsoft Word - AW12-RF Prelim.docx
Creator                         : PrimoPDF http://www.primopdf.com
Author                          : DanielL

EXIF Metadata provided by EXIF.tools