Motorola Solutions 92FT5865 Mobile 2-Way Radio User Manual APX Mobile O2 Control Head
Motorola Solutions, Inc. Mobile 2-Way Radio APX Mobile O2 Control Head
Contents
- 1. Manual
- 2. RF Safety Manual
Manual
APXTM TWO-WAY RADIOS APX MOBILE O2 CONTROL HEAD USER GUIDE m Radio On/Off ASTRO® APX™ O2 Control Head Mobile Radio Quick Reference Card RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations ATTENTION! This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Station which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. Radio Controls LED Indicators Power Button Up & Down Emergency Button* Buttons* Press the Power button to turn the radio on or off. Adjusting Volume If volume is set as the primary mode, 1 Turn the MFK clockwise to increase volume or counterclockwise to decrease the volume. If volume is not set as the primary mode, press the MFK once and repeat step 1. Rotate the MFK or D or U to the desired zone. Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the selected zone number. Press the PTT button to begin transmitting on the displayed zone. Selecting a Channel Dimmer Button Menu Select Buttons* Accessory Port (Microphone) *These controls/buttons are programmable. Rotate the MFK or press D or U to the desired channel. Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the channel. Press the PTT button to transmit on the displayed channel. Take the microphone off the hook. Selecting a Zone If zone is set as the primary mode, 1 Turn the MFK until the display shows the desired zone and press the PTT button to begin transmitting on the displayed zone. If zone is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to scroll to Zone. 3 Press the Menu Select button directly below Zone. Multi-function Knob (MFK)* Home Button 2 > or < (on the keypad mic.) to scroll to Chan. 3 Press the Menu Select button directly below Chan. If channel is set as the primary mode, 1 Turn the MFK until the display shows the desired channel and press the PTT button to begin transmitting on the displayed channel. If channel is not set as the primary mode, press the MFK once and repeat step 1. OR Receiving and Transmitting Select zone/channel. Listen for a transmission. OR > or < (on the keypad mic.) to Mon then press the Menu Select button directly below Mon and listen for activity. Adjust volume, if necessary. Press the PTT button to transmit; release to receive. Sending an Emergency Alarm Press the Emergency button. A tone sounds and the display alternates Emergency and the home display. A dispatcher acknowledgment Ack received display follows. AND, Trunking Only: A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller. To exit emergency at any time, press and hold the Emergency button or the PTT button. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2012, 2013 by Motorola Solutions, Inc. All Rights Reserved. 06/13 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. *PMLN6193C* PMLN6193C English Sending an Emergency Call (Trunking Only) Press Emergency button. A tone sounds and the display alternates Emergency and the home display. OR A short low-pitched tone sounds when the selected channel does not support emergency. Press and hold the PTT button. Speak clearly into the microphone. Release the PTT to end the transmission. To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Alarm Press the preprogrammed Emergency button to activate the silent alarm feature. The display does not change; the LED does not light up, and there is no tone. If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. Direct radio-to-radio communication or communication through a repeater. On = Direct Off = Repeater This channel is being monitored. Voice muting the affiliated trunking talkgroup or selected channel. On = Enabled Off = Disabled H . OR Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the PriorityTwo Channel during scan. The vote scan feature is enabled. Receiving a call or data. Transmitting a call or data. Received an Individual Call. The more stripes, the stronger the signal strength for the current site (trunking only). English On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable. Inverted = User is currently associated with the radio. On = Packet data is activated. Off = Packet data is deactivated. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data activity is present. MFK is in Mode Change feature Turn the MFK to change channel. Display Status Icons On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list. On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. MFK is in Volume Change feature Turn the MFK to adjust the volume. Menu Navigation < or > to Menu Entry (on the keypad mic.). g directly below Menu Entry to select. U or D to scroll through sub-list. H to exit. g directly below Menu Entry to select. Declaration of Conformity DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: Motorola Solutions, Inc., 1303 East Algonquin Road Schaumburg, IL60196, U.S.A. Phone Number: 1-800-927-2744 Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Hereby declares that the product: Model Name: APX Mobile conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. English Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. Declaration of Conformity • Increase the separation between the equipment and receiver. ii English • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The following FCC information applies to Bluetooth radio options IC Model Name: PMHN4193A Description: O2 Bluetooth Option Board FCC ID: AZ492FT6002 IC: 109U-92FT6002 Conforms to the following regulations: FCC Part 15, Section 15.19, 15.12, and 15.105 Note: Changes or modifications not expressly approved by Motorola may void the users authority, as authorized by the FCC, to operate this device and should not be made. See 47 CFR Part 15.21. Information to user.The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Part. 15.19(3). Declaration of Conformity Additional FCC Notes to Users This device has been tested and found to comply with the limits of Part 15.15 of the FCC rules. Parties responsible for equipment compliance should note that the limits specified in this part will not prevent harmful interference under all circumstances. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. See Part 15.105b These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. iii English However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Declaration of Conformity • Consult the dealer or an experienced radio/TV technician for help. iv English Industry Canada (IC) Statements: This Class B digital apparatus complies with ICES-003 and Radio Standards Specification (RSS) 210. Contents Important Safety Information. . . . . . . . . . . . . . .ix RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix Software Version . . . . . . . . . . . . . . . . . . . . . . . . x Notice to Users (FCC and Industry Canada) . . . . . . . x Informations importantes sur la sécurité . . . . . x Disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xii Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . .1 How to Use This User Guide . . . . . . . . . . . . . . . . . . . 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . 1 Additional Performance Enhancement . . . . . . . . . . . 2 Dynamic System Resilience (DSR) . . . . . . . . . . . . . 2 CrossTalk Prevention . . . . . . . . . . . . . . . . . . . . . . . . 2 Encrypted Integrated Data (EID) . . . . . . . . . . . . . . . 2 SecureNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 P25 Digital Vehicular Repeater System (DVRS) . . . 2 What Your Dealer/System Administrator Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 GUIDE SUR L’EXPOSITION AUX RADIOFRÉQUENCES ET LA SÉCURITÉ DU PRODUIT POUR RADIOS MOBILES BIDIRECTIONNELLES. . . . . . . . . . . . . . . . . . . . . . . x Preparing Your Radio for Use . . . . . . . . . . . . . .3 Version du logiciel . . . . . . . . . . . . . . . . . . . . . . .xi Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . 5 Avis aux utilisateurs (FCC et Industrie Canada) . . . .xi Computer Software Copyrights. . . . . . . . . . . . xii Contents Declaration of Conformity . . . . . . . . . . . . . . . . . .i Documentation Copyrights. . . . . . . . . . . . . . . .xii Turning On the Radio. . . . . . . . . . . . . . . . . . . . . . . . . 4 Validating Compatibility During Power Up . . . . . . . . 4 Identifying Radio Controls . . . . . . . . . . . . . . . . .5 Radio Parts and Controls. . . . . . . . . . . . . . . . . . . . . . 6 O2 Control Head and Microphone . . . . . . . . . . . . . . 6 English Programmable Features . . . . . . . . . . . . . . . . . . . . . . 7 One Touch Button . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Assignable Radio Functions . . . . . . . . . . . . . . . . . . . 7 Assignable Settings or Utility Functions . . . . . . . . . . 9 Accessing the Preprogrammed Functions . . . . . . . 10 Using the Menu Select Buttons . . . . . . . . . . . . . . . . 10 Using the Advance Programmable Buttons. . . . . . . 11 Using the Navigation Buttons . . . . . . . . . . . . . . . . . 11 Home Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Multi-function Knob . . . . . . . . . . . . . . . . . . . . . . . . . 12 The MFK button on your radio is programmable to the following features : . . . . . . . . . . . . . . . . . . . . . . . . . 12 Contents Using the Keypad . . . . . . . . . . . . . . . . . . . . . 14 Keypad Characters – Uppercase Mode . . . . . . . . . 14 Keypad Characters – Lowercase Mode . . . . . . . . . 15 Keypad Characters – Numeric Mode . . . . . . . . . . . 16 Keypad Characters – Hexadecimal Mode . . . . . . . . 17 vi Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . 18 Call Type Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Multi-function Knob - Concentric Ring LED . . . . . . 24 Intelligent Lighting Indicators . . . . . . . . . . . . . . . 25 Alert Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 General Radio Operation . . . . . . . . . . . . . . . . . 31 Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . 32 Receiving and Responding to a Radio Call. . . . . . . 32 Receiving and Responding to a Talkgroup Call . . . .33 Receiving and Responding to a Private Call (Trunking Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Receiving and Responding to a Telephone Call . . .34 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . 35 Making a Talkgroup Call . . . . . . . . . . . . . . . . . . . . .35 Making a Private Call (Trunking Only) . . . . . . . . . . .36 Making a Telephone Call . . . . . . . . . . . . . . . . . . . . .37 Identifying Status Indicators . . . . . . . . . . . . . .18 Repeater or Direct Operation . . . . . . . . . . . . . . . . . 37 Status Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . . 38 Monitoring a Channel . . . . . . . . . . . . . . . . . . . . . . . .38 Conventional Mode Operation . . . . . . . . . . . . . . . . .39 Text Messaging Service (TMS) Icons . . . . . . . . . . . 21 Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 TMS Menu Options . . . . . . . . . . . . . . . . . . . . . . 22 English Advanced Features. . . . . . . . . . . . . . . . . . . . . . 40 Receiving a Selective Call. . . . . . . . . . . . . . . . . . . . 41 Making a Selective Call. . . . . . . . . . . . . . . . . . . . . . 41 Using the Talkgroup Call Feature (Conventional Operation Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Selecting a Talkgroup . . . . . . . . . . . . . . . . . . . . . . . 42 Sending a Status Call. . . . . . . . . . . . . . . . . . . . . . . .43 Using the Dynamic Regrouping Feature (Trunking Only) 44 Requesting a Reprogram . . . . . . . . . . . . . . . . . . . . 44 Classifying Regrouped Radios . . . . . . . . . . . . . . . . 45 Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Making a Private Call from Contacts . . . . . . . . . . . .46 Adding a New Contact Entry . . . . . . . . . . . . . . . . . .47 Deleting a Contact Entry . . . . . . . . . . . . . . . . . . . . .48 Adding a Contact to a Call List or Phone List. . . . . .49 Editing a Contact in a Call List or a Phone List . . . .49 Editing an Entry Alias . . . . . . . . . . . . . . . . . . . . . . . 49 Editing as Entry ID . . . . . . . . . . . . . . . . . . . . . . . . . 50 Editing a Call Type . . . . . . . . . . . . . . . . . . . . . . . . . 51 Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Viewing a Scan List . . . . . . . . . . . . . . . . . . . . . . . . .51 Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Turning Scan On or Off. . . . . . . . . . . . . . . . . . . . . . 53 Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only) . . . . . . . . . . . . . . . . 54 Transmitting While the Scan is On . . . . . . . . . . . . . 54 Contents Advanced Call Features. . . . . . . . . . . . . . . . . . . . . . 40 Calling a Phone Not in the List . . . . . . . . . . . . . . . . .40 Receiving and Making a Selective Call (Conventional Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Editing the Scan List . . . . . . . . . . . . . . . . . . . . . . . . 52 Changing the Scan List Status . . . . . . . . . . . . . . . . 52 Viewing and Changing the Priority Status . . . . . . . 53 Radio Programmed for Talkback Scan . . . . . . . . . 54 Radio Programmed for Non-Talkback Scan . . . . . 55 Deleting a Nuisance Channel . . . . . . . . . . . . . . . . . Restoring a Nuisance Channel . . . . . . . . . . . . . . . . Changing Priorities Status While Scan is On . . . . . Restoring Priorities in a Scan List . . . . . . . . . . . . . . Hang Up Box (HUB) . . . . . . . . . . . . . . . . . . . . . . . . 55 55 56 56 56 Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Receiving a Call Alert Page . . . . . . . . . . . . . . . . . . 57 Sending a Call Alert Page. . . . . . . . . . . . . . . . . . . . 58 In-Call User Alert . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . 59 Sending an Emergency Alarm . . . . . . . . . . . . . . . . 60 Sending an Emergency Call (Trunking Only) . . . . . 60 Sending an Emergency Alarm with Emergency Call 60 Sending a Silent Emergency Alarm . . . . . . . . . . . . 61 Special Considerations for Emergencies . . . . . . . . 62 vii English Automatic Registration Service (ARS) . . . . . . . . . . 63 Selecting or Changing ARS Mode . . . . . . . . . . . . . . 63 Accessing the User Login Feature . . . . . . . . . . . . . 64 Logging In as a User . . . . . . . . . . . . . . . . . . . . . . . 64 Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Text Messaging Service (TMS) . . . . . . . . . . . . . . . . 66 Accessing TMS Feature . . . . . . . . . . . . . . . . . . . . . 66 Composing and Sending a New Text Message . . . 67 Sending a Quick Text Message. . . . . . . . . . . . . . . . 68 Using the Priority Status and Request Reply Features 70 Contents Appending or Removing a Priority Status to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Appending or Removing a Request Reply to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Appending a Priority Status and a Reply Request to a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Removing a Priority Status and a Reply Request from a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 viii English Managing Text Messages . . . . . . . . . . . . . . . . . . . . 71 Receiving a Text Message . . . . . . . . . . . . . . . . . . . 71 Viewing a Text Message from the Inbox. . . . . . . . . 72 Replying to a Received Text Message . . . . . . . . . . 73 Accessing the Drafts Folder . . . . . . . . . . . . . . . . . . 74 Managing Sent Text Messages . . . . . . . . . . . . . . . . 74 Viewing a Sent Text Message . . . . . . . . . . . . . . . . 74 Sending a Sent Text Message . . . . . . . . . . . . . . . . 75 Deleting Text Messages . . . . . . . . . . . . . . . . . . . . .76 Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . 76 Managing Encryption . . . . . . . . . . . . . . . . . . . . . . . .76 Loading a Single Encryption Key . . . . . . . . . . . . . .76 Loading the Group Encryption Keys . . . . . . . . . . . .77 Using the Multikey Feature . . . . . . . . . . . . . . . . . . .77 Selecting an Encryption Key (Conventional Only). .78 Enabling Secure Transmission . . . . . . . . . . . . . . . .78 Accessing the Secure Feature . . . . . . . . . . . . . . . .79 Selecting a Keyset. . . . . . . . . . . . . . . . . . . . . . . . . .79 Erasing the Selected Encryption Keys . . . . . . . . . .79 Requesting an Over-the-Air Rekey . . . . . . . . . . . . .80 MDC Over-the-Air Rekeying (OTAR) Page. . . . . . .80 Infinite UKEK Retention. . . . . . . . . . . . . . . . . . . . . .80 Hear Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 The Global Positioning System (GPS) . . . . . . . . . . 81 Understanding the GPS Feature . . . . . . . . . . . . . . .81 Enhancing GPS Performance . . . . . . . . . . . . . . . . .82 The Outdoor Location Feature (Using GPS) . . . . . .82 Accessing the Outdoor Location Feature . . . . . . . .83 Saving a Waypoint . . . . . . . . . . . . . . . . . . . . . . . . .84 Viewing a Saved Waypoint . . . . . . . . . . . . . . . . . . .85 Editing the Alias of a Waypoint . . . . . . . . . . . . . . . .86 Editing the Coordinates of a Waypoint . . . . . . . . . .86 Deleting a Single Saved Waypoint . . . . . . . . . . . . .87 Deleting All Saved Waypoints . . . . . . . . . . . . . . . . .88 Measuring the Distance and Bearing from a Saved Trunking System Controls . . . . . . . . . . . . . . . . . . . . 89 Using the Failsoft System . . . . . . . . . . . . . . . . . . . .89 Going Out-of-Range . . . . . . . . . . . . . . . . . . . . . . . . .90 SmartZone®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Using Site Trunking Feature . . . . . . . . . . . . . . . . . .90 Locking and Unlocking a Site . . . . . . . . . . . . . . . . . .91 Viewing and Changing a Site . . . . . . . . . . . . . . . . . .91 Viewing the Current Site . . . . . . . . . . . . . . . . . . . . . 91 Changing the Current Site . . . . . . . . . . . . . . . . . . . 92 Trunked Announcement . . . . . . . . . . . . . . . . . . . . . .92 Initiating an Announcement . . . . . . . . . . . . . . . . . . 93 Ignition Switch Options . . . . . . . . . . . . . . . . . . . . . . 93 Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Tx Inhibit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 PTT Tx Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Soft Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Ignition Only Power Up . . . . . . . . . . . . . . . . . . . . . .94 Emergency Power Up . . . . . . . . . . . . . . . . . . . . . . .94 Auto Power Off Timer. . . . . . . . . . . . . . . . . . . . . . . .95 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Viewing Recent Calls List. . . . . . . . . . . . . . . . . . . . .95 Selecting the Power Level . . . . . . . . . . . . . . . . . . . .96 Selecting a Radio Profile . . . . . . . . . . . . . . . . . . . . 96 Controlling the Display Backlight . . . . . . . . . . . . . . 97 Turning Keypad Tones On or Off . . . . . . . . . . . . . . 97 Turning Voice Mute On or Off . . . . . . . . . . . . . . . . . 98 Using the Time-Out Timer . . . . . . . . . . . . . . . . . . . 98 Using the Conventional Squelch Operation Features99 Analog Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Digital Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Contents Waypoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Using the Location Feature While in Emergency Mode 89 Using the PL Defeat Feature . . . . . . . . . . . . . . . . 100 Using the Digital PTT ID Feature . . . . . . . . . . . . . 100 Using the Smart PTT Feature (Conventional Only)100 Accessing General Radio Information . . . . . . . . . 101 Accessing Radio Information . . . . . . . . . . . . . . . . 101 Viewing IP Information. . . . . . . . . . . . . . . . . . . . . 102 Viewing Control Assignments . . . . . . . . . . . . . . . 102 Using Siren, PA and Light . . . . . . . . . . . . . . . . . . 103 Using Keypad as Siren Type Selector . . . . . . . . Using Keypad as Light Type Selector . . . . . . . . . Using the Public Address Button on the Keypad . Using the External Public Address Button on the Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 103 103 104 Using Optional External Alarms (Horn and Lights) 104 Using Non-Permanent Horn and Lights. . . . . . . . Using Permanent Horn and Lights. . . . . . . . . . . . Changing the Selected Alarms . . . . . . . . . . . . . . Receiving a Call While Alarms are Turned On . . Turning Off Non-Rearmable External Alarms . . . 104 105 105 106 106 ix English Turning Off Rearmable External Alarms. . . . . . . . 106 Using the Voice Announcement . . . . . . . . . . . . . . 107 Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .108 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Appendix: Maritime Radio Use in the VHF Frequency Range. . . . . . . . . . . . . . . . . . . . . . .110 Special Channel Assignments. . . . . . . . . . . . . . . . 110 Emergency Channel . . . . . . . . . . . . . . . . . . . . . . . 110 Non-Commercial Call Channel . . . . . . . . . . . . . . . 111 Operating Frequency Requirements . . . . . . . . . . . 111 Declaration of Compliance for the Use of Distress and Safety Frequencies . . . . . . . . . . . . . . . . . . . . . . . 113 Contents Technical Parameters for Interfacing External Data Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 Commercial Warranty and Service . . . . . . . .118 English Important Safety Information ATTENTION! This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Station which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. For a list of Motorola-approved antennas and other accessories, visit the following website: http://www.motorolasolutions.com/APX This radio transmitter has been approved by Industry Canada to operate with the Motorola-approved antenna types with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Note: Setting up the radio as an RF Modem takes complete control of the radio. In this mode, the radio no longer responds to button and PTT presses nor will it unmute to voice activity. This mode is designed to receive and pass specifically formatted over the air data to a tethered computer with RF modem enabled applications. This mode can only be exit by reprogramming the radio with Customer Programming Software (CPS) to not operate in RF modem mode and cycling power. Important Safety Information RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. ix English Software Version All the features described in the following sections are supported by the radio's software version R08.05.00 or later. Accessing Radio Information on page 101 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported. Informations importantes sur la sécurité Guide sur l’exposition aux radiofréquences et la sécurité du produit pour radios mobiles bidirectionnelles Mise en garde Notice to Users (FCC and Industry Canada) Software Version This device complies with Part 15 of the FCC rules, Industry Canada license-exempt RSS standard(s) and RSS 210 of the Industry Canada rules per the conditions listed below: 1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. 3 Changes or modifications made to this device, not expressly approved by Motorola, could void the user's authority to operate this equipment. English Avant d'utiliser ce produit, lisez les directives d'utilisation sécuritaire présentées dans le livret Sécurité du produit et exposition à l'énergie RF accompagnant votre radio. ATTENTION! Cette radio est réservée à un usage professionnel seulement pour satisfaire les normes d'exposition à l'énergie RF de la FCC. Avant d'utiliser ce produit, lisez le guide inclus avec votre radio, qui contient d'importantes informations sur le mode d'emploi sécuritaire du produit ainsi que des informations relatives à l'énergie de RF et à son contrôle, afin d'assurer la conformité aux normes et règlements applicables. Pour obtenir une liste d'antennes et d'autres accessoires approuvés par Motorola, consultez le site Web : http://www.motorolasolutions.com/APX Le présent émetteur a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne agréés par Motorola et ayant un gain admissible maximal ainsi que l'impédance requise pour chaque type d'antenne indiqué. Les types d'antenne non inclus, dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Remarque: Régler la radio en tant que modem RF prend le contrôle complet de la radio. Dans ce mode, la radio ne répond plus aux pressions des boutons de commande et PTT, et ne reçoit aucun signal vocal. Ce mode est conçu pour recevoir et transmettre des données spécifiquement formatées pour la liaison radio avec un ordinateur attaché doté d'applications compatibles avec le modem RF. Ce mode ne peut être désactivé qu'en reprogrammant la radio avec un logiciel CPS (programmation client) afin qu'elle ne fonctionne plus en mode modem RF et en la redémarrant. Version du logiciel Toutes les fonctionnalités décrites dans les sections suivantes sont prises en charge par la version du logiciel R08.05.00 ou ultérieure de la radio. Vérifiez auprès de votre détaillant ou de l'administrateur de système pour obtenir des renseignements sur les fonctionnalités prises en charge. Version du logiciel Selon la règlementation d'Industrie Canada, cet émetteur radio ne peut être utilisé qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvés par Industrie Canada pour cet émetteur. Afin de limiter les interférences radio pour les autres utilisateurs, le type et le gain de l'antenne doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (P.I.R.E.) ne soit pas plus forte qu'il ne le faut pour établir la communication. Avis aux utilisateurs (FCC et Industrie Canada) Cet appareil est conforme à la Partie 15 des règlements de la FCC, normes CNR (cahiers des charges sur les normes radioélectriques) pour les appareils exempts de licence d’Industrie Canada et RSS 210 du règlement d'Industrie Canada selon les conditions énumérées cidessous: 1 Ce dispositif ne doit pas causer d'interférences nuisibles. 2 Cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent perturber le fonctionnement. xi English 3 Les changements ou les modifications apportées à ce dispositif, non expressément approuvées par Motorola, peuvent annuler le droit de l'utilisateur à utiliser cet équipement. Computer Software Copyrights Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. xii English Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. Getting Started How to Use This User Guide . . . . . . . . . . . . . . . . . . . . . page 1 Notations Used in This Manual . . . . . . . . . . . . . . . . . . . page 1 Additional Performance Enhancement . . . . . . . . . . . . . page 2 What Your Dealer/System Administrator Can Tell You . page 3 How to Use This User Guide Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.The following special notations identify certain items: WARNING An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed. Getting Started Take a moment to review the following: Notations Used in This Manual This User Guide covers the basic operation of the APX™ Mobile Radios. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Caution Note: An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed. An operational procedure, practice, or condition, etc., which is essential to emphasize. English CrossTalk Prevention Example Description Home button Buttons and keys are shown in bold print or as or H an icon. PHONE Menu entries are shown similar to the way they appear on the radio’s display. This means “Press the right side of the 4-way Navigation button.” (Using keypad mic) Additional Performance Enhancement Getting Started The following are some of the latest creations designed to enhance the security, quality and efficiency of APX mobile radios. Dynamic System Resilience (DSR) DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV & D) or data centric are all supported by DSR. English This feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk. Encrypted Integrated Data (EID) EID provides security encryption and authentication of IV & D data bearer service communication between the radio and the Customer Enterprise Network. SecureNet SecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel. P25 Digital Vehicular Repeater System (DVRS) Motorola Solutions offers an MSI Certified APX compatible, 3rd Party, P25 Digital Vehicular Repeater System (DVRS) that provides low cost portable radio coverage in areas where only mobile radio coverage is available and portable radio coverage is either intermittent or non-existent. What Your Dealer/System Administrator Can Tell You • Is your radio preprogrammed with any preset conventional channels? • Which buttons have been programmed to access other features? • What optional accessories may suit your needs? Turning On the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 Validating Compatibility During Power Up. . . . . . . . . . page 4 Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5 Preparing Your Radio for Use You can consult your dealer or system administrator about the following: Preparing Your Radio for Use English record the Error XX/YY code and contact your dealer. Turning On the Radio Preparing Your Radio for Use Press the Power Button briefly turn on the radio. After a short time, the red, yellow and green LEDs light up. The display then shows Zone and channel text, and menu items display on the screen. The backlight will turn on to the last selected dim level. Note: English If CH Mismatch appears, means that either the Control Head has been connected to an incompatible transceiver, or vice versa. Power Button If your radio does not power up, contact your dealer. To turn off the radio, press the Power Button after the LEDs light up. LEDs Pressing the Power Button before the LED lights up will be ignored. If Fail ##/## appears in the display, the radio will not function until the condition has been corrected. Validating Compatibility During Power Up The radio validates and updates the software and hardware of your control head(s) during power up. Follow the procedure below when your radio runs this task. Procedure: 1 The display shows Maintenance mode remote device; promptly followed by other maintenance statuses. If Error ##/## appears, some non-critical data has been changed. If either of these displays appear, if the display goes blank, or if the unit appears to be locked up, see Helpful Tips on page 108 for more information. 2 The display shows Update done please reset upon If the power-up test is unsuccessful, you see Error XX/YY (XX/YY is an alphanumeric code). Turn off the radio, check the battery, and turn the radio back on. If the radio fails the power-up test again, 3 Press the Power Button to reset. The radio runs the usual completion. OR The display shows Update failed please reset when it fails to update. power up operation if the software updates are complete. OR The radio runs the Maintenance Mode if the updates are not complete and repeat step 1. If Sw incomplete appears, use Flashport Recovery Tool to update the control heads before you power on the radio again. Adjusting the Volume To increase the volume, rotate the Multi-Function Knob (MFK) clockwise. To decrease the volume, rotate the MFK counterclockwise. The display shows volume bars and volume level when you change the volume. Multi-Function Knob Take a moment to review the following: Radio Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . page 6 O2 Control Head and Microphone . . . . . . . . . . . . . . . page 6 Programmable Features . . . . . . . . . . . . . . . . . . . . . . . . page 7 Assignable Radio Functions . . . . . . . . . . . . . . . . . . . . page 7 Assignable Settings or Utility Functions . . . . . . . . . . . page 9 Accessing the Preprogrammed Functions . . . . . . . . . . page 10 Using the Menu Select Buttons . . . . . . . . . . . . . . . . page 10 Using the Advance Programmable Buttons . . . . . . . page 11 Using the Navigation Buttons . . . . . . . . . . . . . . . . . . page 11 Using the Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14 Keypad Characters – Uppercase Mode . . . . . . . . . . page 14 Keypad Characters – Lowercase Mode . . . . . . . . . . page 15 Keypad Characters – Numeric Mode . . . . . . . . . . . . page 16 Keypad Characters – Hexadecimal Mode . . . . . . . . page 17 Push-To-Talk (PTT) Button. . . . . . . . . . . . . . . . . . . . . . page 18 Identifying Radio Controls Note: Identifying Radio Controls English Radio Parts and Controls Navigation Button (Microphone) O2 Control Head and Microphone Bluetooth Indicator** Emergency Button* LED Indicators Identifying Radio Controls Power Button Push-to-Talk (PTT) Button Up & Down Buttons* Data Feature Button* Cancel Button () Home Button (Microphone) Okay/Select Button () Accy No-Dot Button (Purple)* Keypad *This button is programmable. Note: Multi-function Knob (MFK)* Home Button Dimmer Button Menu Select Buttons* Accessory Port (Microphone) *These controls/buttons are programmable. ** Your radio’s hardware is Bluetooth ready. Check with your dealer or system administrator for more details of all the features supported English Accy 1-Dot Button* Accy 2-Dot Button* The microphone is not part of a radio. It is an optional accessory. Programmable Features Call Alert – Allows the radio to function like a pager, or to verify if a radio is active on the system. Call Response – Allows you to answer a private call or phone call. The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press: Delete – Deletes digit, or deletes a nuisance channel in Scan. • Press – Pressing and releasing rapidly. • Long press – Pressing and holding for the programmed duration (between 0.25 seconds and 3.75 seconds). • Hold down – Keeping the button pressed. One Touch Button Each of the four Menu Select buttons, the Emergency button and the three Accy buttons on the microphone are programmable buttons which can be preprogrammed by a qualified radio technician to a default function which is activated upon a short press. Assignable Radio Functions Auxiliary – Switches back and forth between two radios that are attached to the same control head. Channel – Selects a channel. Contacts – Selects the Contacts menu. Digital Vehicle Repeater System – Toggles between the Digital Vehicle Repeater System (VRS) mode. Dynamic Priority (Conventional Only) – Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Emergency – Depending on the programming, initiates or cancels an emergency alarm or call. Identifying Radio Controls Any reference in this manual to a control that is “preprogrammed” means that the control must be programmed by a dealer or a qualified radio technician using the radio’s programming software, in order to assign a feature to that control. Information – Displays the basic radio information, IP-related information, and buttons or switches control mapping. Intercom – Enables users of multiple control heads to talk to each other via the control heads in a multi-control head setup. Internet Protocol Address – Displays the Internet Protocol (IP) address, device name, and status of the radio. Location – Determines the current location (latitude, longitude, time and date), and also the distance and bearing to another English location. Or, turns the GPS functionality on or off for all locations. Message – Enters the current message list. Monitor (Conventional Only) – Monitors a selected channel for all radio traffic until function is disabled. Identifying Radio Controls Multiple Private Line (Conventional Only) – Selects the Multiple Private Line lists. Nuisance Delete – Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. The designated transmit channel refers to the user’s selected zone/channel combination from which scan is initiated. One Touch 1 – 4 – Launches a specific feature with one single button-press. You can setup as much as four separately programmed buttons for four different features. Phone – Allows you to make and receive calls similar to standard phone calls. Private Line Defeat (Conventional Only) – Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Private Call (Trunking Only) – Allows a call from an individual radio to another individual radio. Radio Profiles – Allows for easy access to a set of preprogrammed visual and audio settings of the radio. English Ext PA On/Off – Toggles the audio routing between the connected public address (PA) loudspeaker amplifier and the radio’s internal public address (PA) system. Recent Calls – Allows for easy access to the list of calls recently received or made. Rekey Request – Notifies the dispatcher that you require a new encryption key. Repeater Access Button (RAB) (Conventional Only) – Allows to manually send a repeater access codeword. Reprogram Request (Trunking Only) – Notifies the dispatcher that you want a new dynamic regrouping assignment. Request-To-Talk (Conventional Only) – Notifies the dispatcher that you want to send a voice call. Scan – Toggles scan on or off. Scan List Programming – Selects the scan list for editing. Secure/Clear – Toggles secure transmission on or off. Select – Selects the assigned list for editing. Selective Call (Conventional Only) – Calls an assigned radio. Site Display (Trunking Only) – Views the current site or enable a site search for SmartZone operation. Site Lock/Unlock (Trunking Only) – Toggles between lock and unlock mode when using the SmartZone option. Site Search (Trunking Only) – Performs site search for AMSS (Automatic Multiple Site Select) or SmartZone operation. Air Horn – Toggles the external airhorn alert tone on or off. All Tones/Alerts – Toggles all tones on or off. Talkaround/Direct (Conventional Only) – Toggles between using a repeater and communicating directly with another radio. Dimmer – Changes the display brightness. Talkgroup (Conventional Only) – Allows a call from an individual radio to a group of radios. Front/Rear – Switches one of two control heads to be active at one time. Text Messaging Service (TMS) – Selects the text messaging menu. HiLo – Toggles the Hilo Airhorn tones on or off. TMS Quick Text – Selects a predefined message. User Login – Automatically registers with the server. Zone Down – Toggles downward through the zones in the radio. Zone Select – Allows selection from a list of zones. Zone Up – Toggles upward through the zones in the radio. External Radio – Toggles external radio on or off. Backlight – Toggles display backlight on or off. Horns/Lights – Toggles horns and lights feature on or off. Keypad Mute – Toggles the keypad tones on or off. Keypad Lock – Locks the radio’s keypad, or even locks in the radio’s currently operating channel when the Mode Knob scrolls to other channels. Identifying Radio Controls Status – Sends data calls to the dispatcher about a predefined status. Assignable Settings or Utility Functions Low Power – Toggles transmit power level between high and low. Manual – Toggles the manual tone on or off. Public Address On/Off – Toggles the radio’s internal public address (PA) system on or off. Siren – Toggles external siren alert tone on or off. English Identifying Radio Controls Squelch – Toggles squelch level between normal open and tight. Accessing the Preprogrammed Functions TX Power Level – Toggles transmit power level between high and low. You can access various radio functions through one of the following ways: Voice Announcement – Audibly indicates the current feature mode, Zone or Channel the user has just assigned. • A short or long press of the relevant programmable buttons. Voice Mute – Toggles voice mute on or off for the channels which have enabled In-Call User Alert. When Voice Mute is active, the radio remains muted to all conventional dispatch calls and affiliated trunking group calls. Volume Set Tone – Adjusts the volume of the speakers, or adjusts the volume of the radio’s alert tones. Wail – Toggles the external wail alert tone on or off. Yelp – Toggles the external yelp alert tone on or off. 10 English OR • Use the Menu Select Button (g). Using the Menu Select Buttons The Menu Select Buttons allow you to access the menu entries of features. Note: Check with your dealer or system administrator for the list of features activated in your radio. Your radio may be preprogrammed differently from the following example, but the steps for selecting a zone may appear as shown below: • Press the Menu Select button (g) directly below Zone. Using the Advance Programmable Buttons Up & Down Buttons Emergency Button* Using the Navigation Buttons Your radio is equipped with navigation buttons. The navigation buttons will allow you to access the features in the radio. Up and Down Buttons By default, the U and D buttons are used as up and down arrow input. Menu Select Buttons* Accy No-Dot Button (Purple)* Accy 1-Dot Button* These buttons are programmable. They can be programmed to navigate through zones, channels and to increase and decrease the volume of the radio. Identifying Radio Controls This feature is to help you to shorten the process of applying certain common features. (Quick Access) One Touch Button – Enters a menu with a short press on the preprogrammed One Touch button. Features assigned to these buttons are Call, Call Alert, Phone, Repeater Access, MDC RTT Button Access, Status and Message. Right and Left Buttons Accy 2-Dot Button* The > and < buttons mentioned throughout the manual can be found on the keypad microphone (keypad mic.). * These programmable buttons support the One These buttons will allow you to navigate the lists in the radio. Touch Button feature. 11 English Home Button Multi-function Knob The H button returns you to the home (default) display. In most cases, this is the current mode. The MFK button on your radio is programmable to the following features : For selected radio features, the H button is also used to save user-edited radio settings or information before returning you to the Home screen. Mode Change Identifying Radio Controls Note: Some features do not require you to press H to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information. The H button also can revert to home channel from any other zone and mode in the radio. Check with your dealer or system administrator for more information. Dimmer Button Use this button to adjust the brightness of the display. Long press to toggle between day and night mode. 12 English - Press the MFK once and turn clockwise to scroll the channel list. Volume Change -Turn the MFK clockwise or counterclockwise to adjust the volume level of the speaker. The volume level can be adjusted in 16 steps or 32 steps. A fast turn of the MFK adjusts the volume level in 16 steps with large increments in volume level. A slow turn of the MFK adjusts the volume level in 32 steps with small increments in volume level. The display shows the volume level and bars to indicate the current level. The level of last selected volume when your radio powers down remains the same when the radio powers up. The main display shows the icon of the secondary feature.The main display does not show the icon of primary feature. Your radio by default is set to use the primary feature. Short press the MFK to toggle it to work on either the secondary or primary feature. The concentric ring LED on the MFK will blink in green when the knob is set to secondary feature. If the MFK is set to operate only one feature, it is recommended that it be set to Volume Change. Consult your dealer or system administrator for the best option available for MFK. Concentric Ring LED Identifying Radio Controls The secondary feature has an inactivity timer. This timer starts when the secondary feature is idle. The radio returns to primary feature when the timer expires. 13 English Using the Keypad You can use the 3 x 4 alphanumeric keypad on the keypad microphone to access your radio’s features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs to be pressed to generate the required character. Keypad Characters – Uppercase Mode Identifying Radio Controls Number of Times Key is Pressed 14 Key 10 11 12 13 14 15 16 17 18 19 20 21 “ ‘ 4 G 6 M 9 W 0 Toggle between mixed case mode, uppercase mode, and lowercase mode. * Space # Toggle between numeric and letter mode. English Keypad Characters – Lowercase Mode Key 10 11 12 13 14 15 16 17 18 19 20 21 “ ‘ 6 m Identifying Radio Controls Number of Times Key is Pressed 0 Toggle between mixed case mode, uppercase mode, and lowercase mode. * Space # Toggle between numeric and letter mode. 15 English Keypad Characters – Numeric Mode Identifying Radio Controls Number of Times Key is Pressed Key 10 11 12 13 14 15 16 17 18 19 20 21 “ ‘ * Space # Toggle between numeric and letter mode. 16 English Keypad Characters – Hexadecimal Mode Key 10 11 12 13 14 15 16 17 18 19 20 21 Identifying Radio Controls Number of Times Key is Pressed * Not applicable # Not applicable 17 English Push-To-Talk (PTT) Button The PTT button on the side of the microphone serves two basic purposes: Your radio indicates its operational status through the following: PTT Button • While a call is in progress, the Identifying Status Indicators PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. • While a call is not in progress, the PTT button is used to make a new call. See Making a Radio Call on page 35 for more information. 18 English Identifying Status Indicators Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 19 Text Messaging Service (TMS) Icons . . . . . . . . . . . . . page 21 Status Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 21 TMS Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . page 22 LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24 Intelligent Lighting Indicators . . . . . . . . . . . . . . . . . . . . page 25 Alert Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26 Status Icons The following are the icons that appear on the radio’s display. Receiving Radio is receiving a call or data. Transmitting Radio is transmitting a call or data. Call Received Radio has received an Individual Call. Received Signal Strength Indicator (RSSI) The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal. Direct • On = Radio is currently configured for direct radio-to-radio communication (during conventional operation only). Monitor (Carrier Squelch) Selected channel is being monitored (during conventional operation only). In-Call User Alert • On = The feature is enabled. Voice muting of the affiliated trunking talkgroup or selected channel is activated. • Off = The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected channel is deactivated. H . or Power Level • L = Radio is set at Low power. • H = Radio is set at High power. Scan Radio is scanning a scan list. Identifying Status Indicators The liquid crystal display (LCD) of your radio shows the radio status, text entries, and menu entries. Priority Channel Scan • Blinking dot = Radio detects activity on channel designated as Priority-One. • Steady dot = Radio detects activity on channel designated as Priority-Two. • Off = Radio is connected with other radios through a repeater. 19 English k Vote Scan Enabled The vote scan feature is enabled. Secure Operation User Login Indicator (IP Packet Data) • Off = Packet data context deactivated. • Off = Clear operation. • Blinking = Device registration or user Identifying Status Indicators • Blinking = Receiving an encrypted voice call. registration with the server failed due to an invalid username or pin. AES Secure Operation • Off = Clear operation. • Blinking = Receiving an encrypted voice call. Location Signal 20 English • On = Location feature is enabled, and location signal is available. • Off = Location feature is disabled. • Blinking = Location feature is enabled, but no location signal is available. radio. • On = Packet data context activated. • On = Secure operation. • On = AES Secure operation. • Inverted = User is currently associated with the Data Activity Data activity is present. Hexadecimal Indicates that the text entry is currently in hexadecimal mode. MFK is in Mode Change feature Turn the MFK to change channel. MFK is in Volume Change feature Turn the MFK to adjust the volume. Text Messaging Service (TMS) Icons 3/6 Status Icons The following icons appear on the radio’s display for TMS features: Inbox Full The Inbox is full. Message Sent The text message is sent successfully. Message Unsent The text message cannot be sent. Unread Message • User receives a new message. Read Message The selected text message in the Inbox has been read. Message Index Indicates the index of the current message the user is viewing. Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column. Priority Status Request Reply • The “Priority” feature is toggled on before the message is sent. • Messages in the Inbox folder are flagged with “Priority”. Identifying Status Indicators This feature allows you to send and receive text messages. See Text Messaging Service (TMS) on page 66 for more information. • The “Request Reply” feature is toggled on before the message is sent. • Messages in the Inbox folder are flagged with “Request Reply”. • The selected text message in the Inbox has not been read. 21 English Priority Status and Request Reply Mixedcase Predictive Indicates that the text entry is currently in mixed case and with predicted words shown at the bottom of the screen. • User is composing a message with a priority status and a request for a reply. • Messages in the Inbox folder are flagged with Uppercase Predictive Indicates that the text entry is currently in uppercase and with predicted words shown at the bottom of the screen. Identifying Status Indicators ”Priority” and “Request Reply”. Numeric Indicates that the text entry is currently in numeric mode. Mixed Case Indicates that the text entry is currently in normal text mode. Uppercase Indicates that the text entry is currently in uppercase mode. Lowercase Indicates that the text entry is currently in lowercase mode. 22 English Lowercase Indicates that the text entry is currently in lowercase and with predicted words shown at the bottom of the screen. TMS Menu Options Menu Option Description/Function Back Brings you back to the previous menu screen. Edit Edits a draft message or key in a target address. Save Saves the messages you have edited to the Draft folder. Rply Replies to a message. Del Deletes a message or a character text during editing mode. New Creates a new message. Impt Toggles the “Priority Status” icon on or off for an outgoing message. Description/Function Rqrp Toggles “Request Reply” icon on or off for an outgoing message. Yes Deletes all the messages in the current folder. No Cancel the delete all messages options. Exit Exits to the Home screen. Optn Brings you to the Options main screen. Sel Send Mobile number. Mobile number added to a Call List. Landline phone number. Selects a predefined message or address. Sends the message. Call Type Icons The following icons appear on the radio’s main display, when you make or receive a call, or view selected call lists, to indicate the different call types associated with an alias or ID. Landline phone number added to a Call List. Incoming call or data. Identifying Status Indicators Menu Option Outgoing call or data. Radio number. Radio number added to a Call List. 23 English LED Indicator Multi-function Knob - Concentric Ring LED LED indicator shows the operational status of your radio. Red LED Yellow LED Identifying Status Indicators Green LED 24 The concentric ring LED blinks green when the MFK is using the secondary feature. See Multi-function Knob on page 12 to understand the functionality of MFK. If Intelligent Lighting is activated, the concentric ring LED will not blink green when the MFK is in the secondary mode. The LED turns into solid color of orange, red or green depending on the status of Intelligent Lighting. See Intelligent Lighting Indicators on page 25 for different status of Intelligent Lighting. Solid red – Radio is transmitting. Blinking red – Radio is transmitting at low power condition. Double blinking red – Radio is in Emergency Mode. Rapidly blinking red – Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow – Channel is busy. Blinking yellow – Radio is receiving a secured transmission. Solid green – Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode. Blinking green – Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode. Rapidly blinking green – Radio is on a Priority-One channel while in the Scan List Programming mode. English Concentric Ring LED Intelligent Lighting Indicators Note: This feature must be preprogrammed by a qualified radio technician. Backlight Event Orange Emergency Alerts When The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio is out of range. Red Critical Alerts The radio enters failsoft mode. The radio is unable to establish a full connection with the system. The radio is unable to authenticate or register with the system. The radio receives a private call. Green Call Alerts The radio receives a phone call. The radio receives a call alert. Identifying Status Indicators This feature temporarily changes the radio’s display backlight color and the alert text background color to help signal that a radio event has occurred. The radio receives a selective call. 25 English Alert Tones An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radio’s conditions. The following table lists these tones and when they occur. You Hear Tone Name Radio Self Test Fail Identifying Status Indicators Reject 26 English Short, Low-Pitched Tone Time-Out Timer Warning No ACK Received Individual Call Warning Tone Long, Low-Pitched Tone A Group of Low-Pitched Tones Time-Out Timer Timed Out Talk Prohibit/PTT Inhibit Heard When radio fails its power-up self test. When an unauthorized request is made. Four seconds before time out. When radio fails to receive an acknowledgment. When radio is in an individual call for greater than 6 seconds without any activity. When the Time-Out Timer has expired. (When PTT button is pressed) transmissions are not allowed. Out of Range (When PTT button is pressed) the radio is out of range of the system. Invalid Mode When radio is on an unpreprogrammed channel. Busy When system is busy. You Hear Tone Name Radio Self Test Pass Short, Medium-Pitched Tone Clear Voice Priority Channel Received Emergency Alarm Entry Central Echo Long, Medium-Pitched Tone Volume Set Emergency Exit Failsoft Automatic Call Back Talk Permit A Group of Medium-Pitched Tones Keyfail Console Acknowledge Received Individual Call When correct key is pressed. When radio passes its power-up self test. At beginning of a non-coded communication. When activity on a priority channel is received. When entering the emergency state. When central controller has received a request from a radio. When volume is changed on a quiet channel. When exiting the emergency state. When the trunking system fails. When voice channel is available from previous request. (When PTT button is pressed) verifying system accepting transmissions. When encryption key has been lost. Identifying Status Indicators Valid Key-Press Heard When status, emergency alarm, or reprogram request ACK is received. When Call Alert or Private Call is received. Call Alert Sent When Call Alert is received by the target radio. Site Trunking When a SmartZone trunking system fails. 27 English You Hear Tone Name Fast Ringing Identifying Status Indicators Ringing Heard When system is searching for target of Private Call. Enhanced Call Sent When waiting for target of Private Call to answer the call. Phone Call Received When a land-to-mobile phone call is received. Gurgle Dynamic Regrouping (When the PTT button is pressed) a dynamic ID has been received. Unique, Low-Pitched Chirp New Message When a new message is received. Unique, High-Pitched Chirp Priority Status When a priority message is received. 28 English Tone Name Two high-pitched tones Private Conversation Four high-pitched tones every five seconds Call Alert Single, high-pitched tone Central Acknowledge When When a Private Call is received. When a Call Alert page is received. When a Call Alert, emergency alarm, reprogram request, or status/message transmission is received by the system’s central controller. Four high-pitched tones Mobile Unit Acknowledge When a Call Alert page is received by the intended unit, or the emergency alarm, reprogram request, or status/message transmission is acknowledged by the intended dispatcher. Sound similar to a telephone busy signal A series of two short, high-pitched tones System Busy Automatic Call Back Talk Permit (Optional) When the PTT button is pressed, indicates transmission fail because all system radio channels are in use. Release the PTT button and wait for call back. When a channel is now available for your previously requested transmission. When the PTT button is pressed, indicates the system is accepting your transmission. A series of low-pitched tones followed by a series of high-pitched tones Scan Alert On When Scan feature is activated through the preprogrammed button. A series of high-pitched tones followed by a series of low-pitched tones Scan Alert Off When Scan feature is deactivated through the preprogrammed button. Identifying Status Indicators You Hear 29 English Identifying Status Indicators You Hear Tone Name Continuous, low-pitched tone Talk-Prohibit Single, high-pitched tone every nine seconds Brief low-pitched tone Smart PTT Inhibit (When the PTT button is pressed) the channel is busy with the Smart PTT feature enabled. (When the PTT button is pressed) indicates the radio is not in the range of the trunked radio system. Illegal Mode When you have entered a mode where normal system traffic will be missed, or you are attempting something which is not permitted. Examples include: forgetting to exit the telephone interconnect mode after a call ends (fleet and subfleet calls cannot be received), attempting to transmit on a receive-only conventional mode, attempting to select a dynamic mode where no dynamic ID assignment has been made. Auto Power Off Powers off the radio when no user actions occur during a preprogrammed length of time. Failsoft When a trunked system central controller failure in an unmuted receive condition. The radio reverts from trunked operation to a system similar to conventional radio repeater operation. Other system users can be heard sharing the channel. Time-Out Timer Warning When your present transmission will soon be disabled. or Menu Inactive Exit Valid Key Single, low-pitched tone Invalid Key English (When the PTT button is pressed) the system is out of service. Out-of-Range Single, short, high-pitched tone 30 When When you pressed a valid key, or you entered a feature configuration state, or you are receiving or transmitting in the clear mode on secure models (with TX Clear Alert Tones enabled). When you tried to make an invalid key press, or that an emergency alarm, reprogram request, or status/message was not acknowledged. General Radio Operation Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 31 Selecting a Radio Channel . . . . . . . . . . . . . . . . . . . . . page 32 Receiving and Responding to a Radio Call . . . . . . . . . page 32 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 35 Repeater or Direct Operation . . . . . . . . . . . . . . . . . . . page 37 Monitoring Features. . . . . . . . . . . . . . . . . . . . . . . . . . . page 38 A zone is a group of channels. Note: Your radio must be preprogrammed to allow you to use these features. Procedure: If zone is set as the primary mode, 1 Turn the MFK until the display shows the desired zone and press the PTT button to begin transmitting on the displayed zone. If zone is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to Zone. General Radio Operation Once you understand how your APX Mobile Radio is configured, you are ready to use your radio. Selecting a Zone 3 Press the Menu Select button directly below Zone. The display shows the current zone. 4 Rotate the MFK or press U or D to the desired zone is displayed. 5 Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the selected zone number. 31 English 6 Press the PTT button to begin transmitting on the displayed 6 Press the PTT button to transmit on the displayed channel. zone. Selecting a Radio Channel A channel is a group of radio characteristics, such as transmit/ receive frequency pairs. Use the following procedure to select a channel. General Radio Operation Procedure: Receiving and Responding to a Radio Call Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. Red LED Yellow LED Green LED If channel is set as the primary mode, 1 Turn the MFK until the display shows the desired channel and press PTT to begin transmitting on the displayed. If channel is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to scroll to Chan. 3 Press the Menu Select button directly below Chan. The display shows the current channel. 4 Rotate the MFK or press U or D to the desired channel. 5 Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the channel. 32 English You will see solid red LED while the radio is transmitting. You will see solid yellow LED when the radio is receiving a transmission in conventional mode and there is no LED indication when the radio receives a transmission in trunking mode. If the radio is receiveing a secure transmission, the yellow LED blinks. Receiving and Responding to a Talkgroup Call Procedure: When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed: 1 ASTRO Conventional Only: The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. OR Trunking Only: The display shows the caller alias or ID. 2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to respond to the call. The LED lights up solid red. (Trunking Only) A Private Call is a call from an individual radio to another individual radio. These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller ID. Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: When you receive a Private Call: General Radio Operation To receive a call from a group of users, your radio must be configured as part of that talkgroup. Receiving and Responding to a Private Call 1 You hear two alert tones and the LED blinks green. The display shows Call received and the caller alias or ID. 4 Release the PTT button to listen. 2 Press the Menu Select button directly below Resp within 20 See Making a Talkgroup Call on page 35 for details on making a Talkgroup Call. 3 During the call, the display shows the caller alias (name), if it seconds after the call indicators begin. is in the call list. OR During the call, the display shows the caller ID (number), if the caller’s name is not in the call list. 33 English 4 Press and hold the PTT button to talk. Release the PTT General Radio Operation button to listen. Receiving and Responding to a Telephone Call 5 Press H to hang up and return to the Home screen. This feature allows you to receive calls similar to standard phone calls from a landline phone. Note: If you press PTT button before pressing the Menu Select button directly below Resp, your conversation will be heard by all members of the talk group. Note: If 20 seconds pass before you press the Menu Select button directly below the Resp, you will not respond privately to the call just received. Instead, you initiate a Private Call. Procedure: See Making a Private Call (Trunking Only) on page 36 for details on making a Private Call. 34 English If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. 1 You hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green. The display shows Phone call and the call received icon blinks. 2 Press the Menu Select button directly below Resp. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press H or the Menu Select button directly below Exit to hang up and return to the Home screen. See Making a Telephone Call on page 37 for details. Making a Radio Call • The preprogrammed Zone switchmenu • The Multi-function Knob • A preprogrammed One Touch button • The Contacts list (see Contacts on page 45). Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. To make a call to a group of users, your radio must be configured as part of that talkgroup. Procedure: 1 > or < (on the keypad mic.) to Tgrp and press the Menu Select button directly below Tgrp. The display shows the last-selected talkgroup. 2 Press the Menu Select button directly below Sel. OR Rotate the MFK or U or D to select the channel with the desired talkgroup the press the Menu Select button directly below Sel. 3 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. General Radio Operation You can select a zone, channel, subscriber ID, or talkgroup by using: Making a Talkgroup Call 4 Press the PTT button to make the call. 5 ASTRO Conventional Only: The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only: The LED lights up solid red. 6 Speak clearly into the microphone. 7 Release the PTT button to listen. 35 English Making a Private Call (Trunking Only) 6 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) This feature allows you to send an individual Call Alert or page if there is no answer from the target radio. Your radio must be preprogrammed to allow you to use this feature. 7 When you are connected, the display shows the ID of the General Radio Operation Procedure: Press the preprogrammed Quick Access (One-Touch) Enhanced Private Call button to dial the preprogrammed ID and proceed to Step 5. OR Follow the procedure below. from your mouth. target radio. Press and hold the PTT button to talk. Release the PTT button to listen. OR If no acknowledgment is received, the display shows No acknowledge. OR If the target radio does not respond before the time out, the display shows No answer. 1 > or < (on the keypad mic.) to Call. 8 Press H to return to the Home screen. 2 Press the Menu Select button directly below Call. The See Sending a Call Alert Page on page 55 for more information. display shows the last transmitted or received. 3 Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR D or U to the required ID. OR Use the keypad to enter the required ID. 4 Press the PTT button to start the Private Call. 5 A telephone-type ringing sounds if the receiving unit is in service. The display shows Calling...or Calling... . 36 English 8 Press H to return to the Home screen. This feature allows you to make calls similar to standard phone calls to a mobile or landline phone. See Alert Tones on page 26 for more information if your call is NOT answered. Procedure: Press the preprogrammed Quick Access (One-Touch) Phone Call button to dial the preprogrammed phone number and proceed to Step 5. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Phon. 2 Press the Menu Select button directly below Phon. The display shows the last transmitted phone number. 3 Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR D or U to the required phone number. OR Use the keypad to enter the required phone number. Repeater or Direct Operation The REPEATER operation increases the radio’s range by connecting with other radios through a repeater. The transmit and receive frequencies are different. The DIRECT or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Procedure: Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Dir. 4 Press and release the PTT button to dial the phone number. 2 Press the Menu Select button directly below Dir. 5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) 3 The display shows Repeater mode if the radio is currently from your mouth. 6 When your call is answered, press the PTT button to talk. 7 Release the PTT button to listen. General Radio Operation Making a Telephone Call in Repeater mode. OR The display shows Direct mode and the Talkaround icon if 37 English the radio is currently in Direct mode (during conventional operation only). You can repeat step 2 to toggle between the two modes. Once in Direct Mode, press PTT button to start conversation with the radios nearby. 2 Adjust the volume by rotating the MFK if necessary. 3 If you hear no activity, press and hold the PTT button to start your conversation. OR Trunked Modes Only: General Radio Operation Monitoring Features Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Digital technology quiets the transmission by removing the “noise” from the signal and allowing only the clear voice or data information to be heard. Monitor a channel to ensure the channel is clear before transmitting. Monitoring a Channel Procedure: Lift the microphone off hook. Conventional Modes Only: 1 Listen for activity on that channel. 38 English 1 Press the PTT button. 2 If you hear two, short, high-pitched tones, or if you hear no tone and the t indicator lights steadily, then proceed with your message. 3 Release the PTT button to receive (listen). If you are not in the range of the system, you may hear a continuous low-pitched tone and the display shows Out of range. Conventional Mode Operation Note: This feature must first be enabled by a qualified radio technician or system administrator. Procedure: Take the control head off hook. (This is the same as monitor on. You hear all channel traffic.) OR 1 At Home mode where the default zone and channel are being displayed, > or < button (on the keypad mic.) to Mon. General Radio Operation This feature allows you to monitor channel traffic on conventional channels by defeating the coded squelch. This way, you can listen to another user active on the channel. Thus, you may be prevented from talking over someone else’s conversation. 2 Press the Menu Select button directly below Mon momentarily to activate monitoring. The display shows Monitor on. 3 Press the Menu Select button to deactivate the monitoring. The display shows Monitor off. 39 English Advanced Call Features Advanced Features Advanced Features Use this navigation guide to learn more about advanced features available with your radio: Advanced Call Features . . . . . . . . . . . . . . . . . . . . . . . Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Call Alert Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . Automatic Registration Service (ARS) . . . . . . . . . . . . Text Messaging Service (TMS) . . . . . . . . . . . . . . . . . . Secure Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . The Global Positioning System (GPS) . . . . . . . . . . . . Trunking System Controls . . . . . . . . . . . . . . . . . . . . . . Ignition Switch Options . . . . . . . . . . . . . . . . . . . . . . . . Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 English page 40 page 45 page 51 page 53 page 57 page 59 page 63 page 66 page 76 page 81 page 89 page 93 page 95 Calling a Phone Not in the List > or < (on the keypad mic.) to Phon. Press the Menu Select button directly below Phon. Enter the desired phone number from the optional keypad microphone. The display updates as the numbers are entered. Press button or the PTT button (on the keypad mic.) to make the call. Press and hold the PTT button to talk. Release the PTT button to listen. Press H or Menu Select button directly below Phon to exit. Receiving and Making a Selective Call (Conventional Only) Receiving a Selective Call Procedure: When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The call received icons blink and the display alternates between Call received and the home display. Making a Selective Call Procedure: Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and proceed to Step 4. OR Follow the procedure below. > or < (on the keypad mic.) to Call. The speaker unmutes. Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. Press the Menu Select button directly below Call. The display shows the last transmitted or received ID. Press and hold the PTT button to talk. Release the PTT button to listen. Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR Note: If you press PTT button before pressing the Menu Select button directly below Call, your conversation will be heard by all members of the talk group. Advanced Features This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. If 20 seconds pass before you press the Menu Select button directly below the Call, you will not respond privately to the call just received. Instead, you initiate a Selective Call. See Making a Selective Call on page 41. D or U to the required ID. OR Use the keypad to enter the required ID. Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. Press and hold the PTT button to start the Selective Call. The display shows the ID of the target radio. 41 English 6 Release the PTT button to listen. Selecting a Talkgroup Press H to return to the Home screen. Procedure: If you do not press H button to hang up, your radio will remain in Selective Call state with the other unit. You will miss all subfleet traffic and incoming phone calls. > or < (on the keypad mic.) to Tgrp. Press the Menu Select button directly below Tgrp. The display shows the last talkgroup that was selected and stored. U or D to Pset for the preset preprogrammed talkgroup. OR Using the Talkgroup Call Feature (Conventional Operation Only) This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel. Advanced Features Note: 42 English Encryption keys are associated to talkgroups. When talkgroups are enabled, encryption keys are changed by changing the active talkgroup. See Secure Operations on page 76 for more information. D or U to the required talkgroup. OR Use the keypad to enter the number of the corresponding talkgroup in the list. Press the Menu Select button directly below Sel to save the currently selected talkgroup and return to the Home screen. If the encryption key associated to the new talkgroup is erased, a momentary key fail tone sounds and the display shows Key fail. OR If the encryption key that is associated to the new talkgroup is not allowed, a momentary key fail tone sounds and the display shows Illegal key. Press H or the PTT button to exit. Sending a Status Call When the dispatcher acknowledges, four tones sound and the display shows Ack received. The radio returns to normal dispatch operation. OR If no acknowledgment is received, a low-pitched tone sounds and the display shows No acknowledge. Press H to return to the Home screen. This feature allows you to send data calls to the dispatcher about a predefined status. Each status can have up to a 14-character name. A maximum of eight status conditions is possible. Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Press the preprogrammed Status button and proceed to Step 3. OR Follow the procedure below. > or < (on the keypad mic.) to Sts. Press the Menu Select button directly below Sts. The display shows the last acknowledged status call, or the first status in the list. D or U to the required status. OR Use the keypad to enter a number corresponding to the location in the status list. Press the PTT button to send the status. The display shows Please wait. No traffic is heard on trunked channels while Status Calls is selected. If the radio detects no Status Call activity for six seconds, an alert tone sounds until you press H or the PTT button. Advanced Features 43 English Using the Dynamic Regrouping Feature (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician. You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher. Advanced Features Note: If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds. Procedure: When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A “gurgle” tone sounds and the display shows the dynamically regrouped channel’s name. Press the PTT button to talk. Release PTT button to listen. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. 44 English Requesting a Reprogram This feature lets you notify the dispatcher that you want a new dynamic regrouping assignment. Procedure: Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher and proceed to Step 3. OR Follow the procedure below. > or < (on the keypad mic.) to Rpgm. Press the Menu Select button directly below Rpgm to send reprogram request to the dispatcher. The display shows Reprogram rqst and Please wait. If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows Ack received and the radio returns to the Home screen. OR If the dispatcher does not acknowledge the reprogram request within six seconds, a low-pitched alert tone sounds and the display shows No acknowledge. Try again or press H to cancel and return to the Home screen. Classifying Regrouped Radios • Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position. • Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. This feature provides “address-book” capabilities on your radio. Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call. Contact entries are alphabetically sorted according to entry alias. Each alias can have up to 5 IDs of different call types associated with it. Additionally, each entry, depending on context (conventional, trunking, or phone), associates with one or more of the four types of calls: Phone Call, Selective Call, Private Call, or Call Alert. Advanced Features The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. Contacts Each entry within Contacts displays the following information: • Call Alias (Name) • Call ID (Number) • Call Type (Icon) • WACN ID (Astro 25 Trunking IDs only) • System ID Note: Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries. Your radio also supports a maximum of 50 call lists. Each list can store up to 100 IDs (numbers). 45 English Note: Your radio is preprogrammed with a number of contacts per Call Lists. Check with your dealer or system administrator for more information. If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid green. Making a Private Call from Contacts Procedure: 10 If there is no voice activity for a programmed period of time, the call ends. OR The call ends when it reaches the maximum ring time. Use the Options Menu. OR Advanced Features Note: Your radio must be preprogrammed to allow you to use this feature. > or < (on the keypad mic.) to Cnts. Use the PTT button: Press the Menu Select button directly below Cnts to the call list. The display shows Contact Alias. > or < (on the keypad mic.) to Cnts. D or U to the required subscriber alias. Press the Menu Select button directly below Cnts. Press the Menu Select button directly below Optn. D or U to the required subscriber alias. D or U (on the keypad mic.) to Call and press the Menu Press the Menu Select button directly below Cnts. The display shows Contact Alias. Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. Select button directly below Sel. D or U to select the call type. 46 English Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid yellow. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. If there is no voice activity for a preprogrammed period of time, the call ends. OR The call ends when it reaches the maximum ring time. Press the Menu Select button directly below OK once you have entered the name. OR Press the Menu Select button directly below Cncl to return to the previous screen. D or U to {Add Number} and press the Menu Select button directly below Sel. The display shows Type 1 . Press Menu Select button directly below Edit. D or U to the required channel and press the Menu Select Adding a New Contact Entry Procedure: > or < (on the keypad mic.) to Cnts. Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. D or U to {New Contact} and press the Menu Select button directly below Sel. The display shows Name. Press the Menu Select button directly below Edit. Use the keypad to enter the name. Advanced Features button directly below OK. 47 English 9 D or U to Number 1 and press the Menu Select button directly below Edit. The display shows Number 1 and a cursor appears. Use the keypad to enter the number. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Advanced Features 10 Press the Menu Select button directly below OK once you have entered the number. OR Press the Menu Select button directly below Cncl to return to the previous screen. 11 Press the Menu Select button directly below Done once you have finished. 12 The display shows stored, confirming that the contact entry has been added. 13 The radio returns to the main Contacts screen. 48 English Deleting a Contact Entry Procedure: > or < (on the keypad mic.) to Cnts. Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. D or U to the entry you want to delete and press the Menu Select button directly below Optn. D or U to Delete and press the Menu Select button directly below Sel. The display shows confirm del?. Select Yes to delete the entry. The display shows deleted and the radio returns to the main screen for Contacts. OR Select No to return to the main screen for Contacts. Adding a Contact to a Call List or Phone List Editing an Entry Alias > or < (on the keypad mic.) to Cnts. Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. > or < (on the keypad mic.) to Cnts. D or U to the entry you want to add to the call list and press Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. D or U to the entry you want to edit and press the Menu Procedure: the Menu Select button directly below Optn. D or U to Add to CallLst or Add to PhonLst and press Select button directly below Optn. the Menu Select button directly below Sel. D or U until the display shows {Available} and press the Menu Select button directly below Add to add as a new entry. OR D or U until the display shows and its associated number and press the Menu Select button directly below RPLC to replace the existing entry. The display shows added, confirming the addition of the contact to the list. The radio returns to the main display for Contacts. D or U to Edit and press the Menu Select button directly below Sel. Advanced Features Procedure: Editing a Contact in a Call List or a Phone List D or U to the entry alias you wish to change and press the Menu Select button directly below Edit. A cursor appears. Use the keypad to edit the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 49 English 7 Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. Press the Menu Select button directly below Done to save your changes and return to the main screen for Contacts. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. Editing as Entry ID Advanced Features Procedure: > or < (on the keypad mic.) to Cnts. Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. D or U to the entry you want to edit and press the Menu Select button directly below Optn. D or U to Edit and press the Menu Select button directly below Sel. D or U to the entry ID you wish to change and press the Menu Select button directly below Edit. 50 English A cursor appears. Use the keypad to edit the number. Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. Press the Menu Select button directly below Done to save your changes and return to the main screen for Contacts. Scan Lists Editing a Call Type > or < (on the keypad mic.) to Cnts. Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. D or U to the entry you want to edit and press the Menu Your radio supports different types of Scan Lists: Select button directly below Optn. • Trunking Priority Monitor Scan List D or U to Edit and press the Menu Select button directly • Conventional Scan List below Sel. • Talkgroup Scan List D or U to TYPE and press the Menu Select button directly A maximum of 200 Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician. below Edit. Scan lists are created and assigned to individual channels/ groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. D or U to choose from the list of call types given and press the Menu Select button directly below OK to select. Viewing a Scan List The display returns to the Edit Contact screen. Procedure: Press the Menu Select button directly below Done to save your changes and return to the main screen for Contacts. > or < (on the keypad mic.) to ScnL. Press the Menu Select button directly below ScnL. D or U to view the members on the list. Press the H to exit the current display and return to the Home screen. Advanced Features Procedure: 51 English Editing the Scan List This feature lets you change scan list members and priorities. Advanced Features Procedure: Press H to exit scan list programming and return to the Home screen. See Viewing and Changing the Priority Status on page 53 for more information on how to add and/or change the priority of the currently displayed channel in the scan list. > or < (on the keypad mic.) to ScnL. Press the Menu Select button directly below ScnL. The display shows the lists that can be changed. Changing the Scan List Status D or U to the entry you want to edit. Procedure: Press the Menu Select button directly below Sel to add and/ or change the priority of the currently displayed channel in the scan list. OR Press the Menu Select button directly below Del to delete the currently displayed channel from the scan list. OR Press the Menu Select button directly below Rcl to view the next member of the scan list. D or U to select more channels to be added or deleted. OR Use the keypad to go directly to additional channels to be added or deleted. OR Use the MFK to select additional channels to be added or deleted. 52 English Long press the preprogrammed Scan side button. D or U to the member you want to edit. Press the button or press the Menu Select button directly below Sel once to add the currently displayed channel to the scan list. OR Press the button or press the Menu Select button directly below Sel, one or more times to change the scan list status icon of the currently displayed channel. D or U to select more list members whose scan status you want to change. OR Use the keypad to go directly to that scan list member. OR Use the MFK to select another scan list member. 5 Press H to exit scan list programming and return to the Home screen. Procedure: Below the Sel, Del, and Rcl screen, press the Menu Select button directly below Sel to view and/or change the priority status of the currently displayed channel. OR Below the Sel, Del, and Rcl screen, press the button or press the Menu Select button directly below Sel, one or more times to view and/or change the scan list status icon of the currently displayed channel. A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The LED lights up solid green. OR A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. OR A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the PriorityOne channel, regardless of traffic on non-priority channels. OR No icon indicates that the current channel is deleted from the scan list. This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Turning Scan On or Off Procedure: Press the preprogrammed Scan button. OR Follow the procedure below. > or < (on the keypad mic.) to Scan. Press the Menu Select button directly below Scan. The display shows Scan off if scan is disabled. Press the Menu Select button directly below Scan to enable scan. OR The display shows Scan on and the scan status icon if scan is enabled. Press the Menu Select button directly below Scan to disable scan. The radio returns to the Home screen. Advanced Features Viewing and Changing the Priority Status Scan 53 English Turning Scan On While Disregarding the Squelch Transmitting While the Scan is On Code (Conventional Channels Only) Procedure: > or < (on the keypad mic.) to Mon. Press the Menu Select button directly below Mon. The brief Monitor on display indicates that the radio is disregarding the squelch code. Advanced Features While scanning for activity, you can still receive fleetwide, system-wide, dynamic regrouping, incoming telephone interconnect and Private Conversation/Call Alert calls. Respond to these types of calls as you would normally on the selected channel. However, when scanning different channels while in talkgroup scan, incoming Private Conversation/Call Alert calls may be missed. 54 English Radio Programmed for Talkback Scan Procedure: Press the PTT button to transmit on the channel indicated by the display. The radio does not begin scanning again for a predetermined hang time after you release the PTT button, allowing the other party to respond. If the other party responds within the hang time, scanning does not resume until the full hang time expires after they have finished speaking, allowing the conversation to be completed. To transmit on the selected channel if another channel is active, first turn scan off by pressing the Menu Select button below Scan momentarily. Restoring a Nuisance Channel Procedure: Procedure: To restore the deleted nuisance channel, do one of the following: Press the PTT button at any time to transmit on the selected channel or fixed channel. To make a Call Alert page, or Private Conversation call while scanning, press either the Menu Select button directly below Page or Call. The call is entered on the selected channel and scanning is halted until the call is exited by pressing H or pressing the Menu Select button below either Page or Call. Deleting a Nuisance Channel • Turn scan off, then on. OR • Change modes. OR • Turn off the radio, and then turn it back on. Nuisance mode delete can be disabled by the system administrator. Advanced Features Radio Programmed for Non-Talkback Scan If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to priority channels or the designated transmit channel. Procedure: When the radio is locked onto the channel to be deleted, > or < (on the keypad mic.) to Nuis. Press the Menu Select button directly below Nuis. 55 English Changing Priorities Status While Scan is On Restoring Priorities in a Scan List While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel. Procedure: This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting. Procedure: Advanced Features Press the Menu Select button directly below Dynp to change the priority of a non-priority channel in the scan list to Priority-Two. Press H momentarily to exit the scan list and resume scanning. 56 English To restore the original channel priorities in a scan list, do one of the following: • Turn scan off, then on. OR • Change channels. OR • Turn off the radio, and then turn it back on. Hang Up Box (HUB) To temporarily suspend Scan Mode operation, remove the control head from the Hang Up Box (HUB). You are allowed to use the control head while scan is suspended. However, Priority Member scanning is not suspended. This feature applies to all Scan Lists and Scan Types. Scan is resumed once the control head is returned to the holding clip and the preprogrammed hang time has elapsed. Note: Priority Scan List members are continuously scanned only when the Scan List, Designated Tx Member field is set to “Talkback” in the radio programming. Otherwise, all scan mode operation is suspended. Call Alert Paging Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system. Depending on how your radio is programmed, when you make an Enhanced Private Call, the radio either automatically sends a Call Alert page if there is no answer after the maximum ring time, OR when you press the PTT button. Note: This feature must be preprogrammed by a qualified radio technician. Procedure: When you receive a Call Alert page You hear four repeating alert tone and the green LED blinks. OR You hear one alert tone and the green LED blinks if Call Alert Tone Auto Reset is enabled. The call received icons blinks and the display shows Page received. Press the PTT button to answer. OR Press any button to clear the Call Alert page. Advanced Features This feature allows your radio to work like a pager. Receiving a Call Alert Page See Making a Talkgroup Call on page 35 or Making a Private Call (Trunking Only) on page 36 for more information. 57 English Sending a Call Alert Page Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Advanced Features Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5 of the procedure below. OR Follow the procedure below. The radio returns to the Home screen. OR Press the Menu Select button directly below OK to return to the main screen for Contacts. OR Follow the procedure below. > or < (on the keypad mic.) to Call. Press the Menu Select button directly below Call. D or U to select the required ID, press the PTT button to initiate the call. > or < (on the keypad mic.) to Page. If the target radio does not respond after a preprogrammed period of time, the display shows Send page?. Press the Menu Select button directly below Page. D or U to select the required ID. Press the PTT button to send the page. The display shows Paging... or . Press the Menu Select button directly below Yes to send the call alert page. OR Press the Menu Select button directly below No to exit the screen without sending the call alert page. If the call alert page is sent successfully, four highpitch tone sounds and the display shows Ack received. OR If the call alert page is not acknowledged, a low tone sounds and the display shows No acknowledge. The display shows Paging... . If the call alert page is sent successfully, a tone sounds and the display shows Ack received. OR If the call alert page is not acknowledged, a low tone sounds and the display shows No acknowledge. 58 English 8 In-Call User Alert Emergency Operation The Emergency feature is used to indicate a critical situation. If the Orange button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel. You can enable and disable voice transmission, if needed. Procedure: Make sure you are in Home mode where the default zone and mode are being displayed. > or < (on the keypad mic.) to scroll to the Vmut. Press the Menu Select button directly below Vmut. Press the Menu Select button directly below Vmut or the VMut preprogrammed button again to turn the feature off and you will be able to hear to normal dispatch calls. Pressing the Menu Select button directly below Vmut or the VMut programmed button momentarily toggles between Voice mute on and Voice mute off. Voice mute on shown on the display indicates that the radio is muted to all conventional dispatch calls and affiliated trunking group calls. Your radio supports 5 Emergency modes: • Emergency Call • Emergency Alarm • Emergency Alarm with Call • Silent Emergency Alarm Advanced Features The radio returns to the Home screen. OR Press the Menu Select button directly below OK to return to the main screen for Contacts. • Special Considerations for Emergencies Check with your dealer or system administrator for more information on the programming of this feature. Only one of the Emergency modes above can be assigned to the preprogrammed Emergency button or the Emergency footswitch. Note: To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second. 59 English Sending an Emergency Alarm This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. Press and hold the PTT button. Speak clearly into the microphone. Advanced Features Procedure: Release the PTT to end the transmission. Press the preprogrammed Emergency button. A tone sounds and the display alternates Emergency and the home display. Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. A dispatcher acknowledgment Ack received display follows. AND, Trunking Only: A high-pitched tone indicates that the alarm has been received by the trunked system’s central controller. Sending an Emergency Alarm with Emergency Press and hold the emergency button or the PTT button to return to normal operation. Call This feature allows you to send an Emergency Alarm to another radio. Upon acknowledgement, both radios can communicate over a preprogrammed Emergency channel. Sending an Emergency Call (Trunking Only) If the radio has both emergency call and alarm features enabled, it automatically proceeds to the call mode after the alarm is acknowledged. Procedure: Procedure: Press preprogrammed Emergency button. A tone sounds and the display alternates Emergency and the home display. OR A short low-pitched tone sounds when the selected channel does not support emergency. Press the preprogrammed Emergency button to activate the emergency call/alarm feature. The display alternates Emergency and the home display. 60 English 3 Sending a Silent Emergency Alarm Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. Press and hold the PTT button. Speak clearly into the microphone. Upon acknowledgement, your radio’s microphone is automatically activated, allowing you to communicate with the other radio without pressing the PTT button. Release the PTT to end the transmission. Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. Turning the radio off also cancels the emergency state. This feature allows you to send an Emergency Alarm to another radio without any audio or visual indicator. This activated microphone state is also known as “hot mic”. Note: If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button. Advanced Features A high-pitched tone sounds, indicating that the alarm has been received by the trunked system’s central controller. A dispatcher acknowledgment (four high-pitched tones) follows, accompanied by an Ack received display. Procedure: Press the preprogrammed Emergency button to activate the silent alarm feature. Press and hold the emergency button until a tone sounds to exit the silent alarm mode. If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. 61 English Special Considerations for Emergencies • If you press the emergency button while in a channel that has no emergency capability, a low-pitched tone sounds. • If the unit is out of the range of the system and/or the emergency alarm is not acknowledged, a tone sounds and the display shows No acknowledge. Advanced Features • If you press the emergency button, then change to a mode that has no emergency capability, the display shows No Emergency and a continuous low-pitched tone sounds until a valid emergency mode is selected or until the emergency is cancelled. • When an emergency is active, changing to another mode where emergency is enabled (trunked or conventional) causes an emergency alarm and/or emergency call to be active on the new mode. 62 English Advanced Features Automatic Registration Service (ARS) Procedure: Press and hold > or < (on the keypad mic.) to Chan. Press the Menu Select button directly below Chan. The display shows the current zone is not blinking, and the channel is blinking. Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS). The Automatic Registration Service for the radio consists of two (2) modes: Note: D or U or press the MFK once and rotate the MFK to the desired channel. • ARS Server Mode (default mode) • ARS Non Server Mode After the zone you want is displayed, toggle until the display shows the required channel. OR In ARS Server Mode, the display shows the User Login Indicator icon, the zone, and ARS server channel. OR In ARS Non-Server Mode, the display shows the User Login Indicator icon, the zone, and ARS non-server channel. OR If the channel or mode selected is unprogrammed, the display shows Unprogrammed. Repeat Step 2. Press H to confirm the displayed zone and channel. The default ARS mode can be changed by a qualified radio technician using the radio’s programming software. Advanced Features This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server. Selecting or Changing ARS Mode 63 English Accessing the User Login Feature Logging In as a User This feature allows you as the user to be associated with the radio. With this association, every data application (Example: Text Messaging Service) takes on a friendly username. Procedure: > or < (on the keypad mic.) to User. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message. Press the Menu Select button directly below User. The display shows the User Login screen. Press the Menu Select button directly below ID. A blinking cursor appears beside ID. Use the keypad to enter a username using the keypad multi-tap function. OR Advanced Features Note: 64 English Valid characters for a username entry are capital letters (A – Z), small letters (a – z), numbers (0 – 9), symbols (*, #, -, /), and the space character. D or U to scroll through the list of predefined usernames. Press the Menu Select button to select a predefined username. OR The maximum length for a username is eight (8) characters. Usernames are not case sensitive in server mode but are case sensitive in non-server mode. A predefined username may sometimes be invalid because the programming software that is used to set predefined usernames allows you to set usernames comprising of eight (8) characters or more. Press and hold D or U to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below Logn to select a predefined username. If the selected predefined username has more than eight (8) characters, or an invalid character in it, the display momentary shows Invalid ID. Repeat Step 5. OR Press the Menu Select button directly below PIN. A blinking cursor appears beside PIN. Enter your Personal Identification Number (PIN) number. The maximum PIN length is 4 digits. The PIN number will appear as asterisks. Press the Menu Select button directly below Logn. In ARS server mode, the display shows the User Login Indicator icon, the ID, In progress and Cncl. OR In ARS non-server mode, the display shows the User Login Indicator icon, the ID, Logged in and Logt. In non-ARS enabled mode, the display shows Offline and Logt. 10 If the username is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows Login failed. Repeat step 5. OR If the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows Login failed. Repeat Step 7. OR Press the Menu Select button directly below Cncl to cancel the login in progress screen and return to the initial user login screen. OR Wait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and Logged in and Logt. Once the data application registration is completed, you can log out. Procedure: > or < (on the keypad mic.) to Logt. Press the Menu Select button directly below Logt. Display shows the User Login Indicator icon and Clear private data?. Select Yes to clear all your private data. The display shows momentary Private data cleared. OR Select No to keep your private data. Note: Advanced Features Logging Out Private data refers to all messages in the text messaging Inbox, Draft and Sent folder. The next radio user will be able to access your Inbox, Draft and Sent messages if private data is not deleted. 65 English Text Messaging Service (TMS) This feature allows you to send and receive text messages. The maximum length of characters for a text message is 200. Accessing TMS Feature Note: There are three (3) types of text messages: • A new text message (free form message) Press the Menu Select button directly below Back at any time to return to the previous screen. • A predefined message (quick text message) • An edited quick text message The main menu consists of the following options: • Inbox Advanced Features • Compose • Drafts • Sent Note: 66 English See Status Icons on page 21 for more details on the TMS icons and TMS Menu Options on page 22 for more details on each menu option. If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Press the preprogrammed Data Feature button or the TMS button to access the TMS feature screen. OR Press and hold the preprogrammed Data Feature button or the TMS button to access the Inbox screen. OR Follow the procedure below. > or < (on the keypad mic.) to TMS. Press the Menu Select button directly below TMS to access the TMS feature screen. D or U to scroll through the main menu options. mode, and lowercase mode. Press # to toggle between numeric and letter mode. Composing and Sending a New Text Message During the uppercase and lowercase mode, multitapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. During the num lock mode, except for 1, pressing the keypad only enters the numeric digits. Subsequent presses of the same key inserts the same digit to the text message (no multi-tap). Press the Menu Select button directly below Optn once the message is composed. D or U to Send and press the Menu Select button directly below Send to send. OR D or U to Back and press the Menu Select button directly below Back to return to Compose screen if you want to edit the message. Procedure: D or U to scroll through the address list and press the Menu Select button below Sel to select the required address. OR > or < (on the keypad mic.) to f. Press the Menu Select button directly below TMS to access the TMS feature screen. D or U to Compose. Press the Menu Select button directly D or U to {Other recpnt} and press the Menu Select below Compose to see the compose options. button below Edit. A blinking cursor appears in the Enter address screen. Use the keypad to type the address entry. Press the Menu Select button directly below New to compose a new message. A blinking cursor appears on the Compose screen. Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase Advanced Features Note: Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 67 English 9 Press the Menu Select button below Send to send the message. OR Press the PTT button to send the message. Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently. 10 The display shows the Send message screen and Sending msg. Each Quick Text message has a maximum length of 50 characters. 11 If the message is sent, a tone sounds and the display shows Msg sent. OR If the message is not sent, a low tone sounds and the display shows Send failed. Procedure: Press the preprogrammed Quick Text button and proceed to Step 3. OR Follow the procedure below. If the message fails to send, the radio returns you to the main TMS screen. Advanced Features Sending a Quick Text Message Note: Note: 68 English You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 70 for more information. You can also select the DRFT option to save your message in the Drafts folder to send it at a later time. See Accessing the Drafts Folder on page 74 for more details. > or < (on the keypad mic.) to TMS. Press the Menu Select button directly below TMS to access the TMS feature screen. D or U tto Compose. Press the Menu Select button directly below Compose to access the compose options. D or U to List. D or U to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message. The message appears on the Compose screen, with a blinking cursor at the end of it. Use the keypad to edit the message. Press < to move one space to the left. 7 Press the Menu Select button directly below Optn. D or U to Send and press the Menu Select button directly below Sel to send the message. D or U to scroll through the address list and highlight the required address. OR D or U to {Other recpnt} and press the Menu Select button below Edit. A blinking cursor appears in the Enter address screen. Use the keypad to type the address entry. 10 Press the Menu Select button below Send to send the message. OR Press the PTT button to send the message. 11 The display shows the screen and Sending msg. 12 If the message is sent, a tone sounds and the display shows Msg sent. OR If the message is not sent, a low tone sounds and the display shows Send failed. If the message fails to send, the radio returns you to the main TMS screen. Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 70 for more information. Advanced Features Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 69 English Using the Priority Status and Request Reply Appending or Removing a Request Reply to a Text Message Features Before sending your message, you can append a priority message and/or a request reply to your message. Appending or Removing a Priority Status to a Text Message Note: The Priority Message icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message to let the receiver know that the message is important. Procedure: After the outgoing message is composed (see Composing and Sending a New Text Message on page 67 for more information): Press the Menu Select button directly below Optn. Press the Menu Select button directly below Rqrp. The reply status icon appears beside the normal message icon on the label bar. Press the Menu Select button directly below Rqrp again. The reply status icon and the normal message icon disappear from the label bar. Advanced Features Procedure: After the outgoing message is composed (see Composing and Sending a New Text Message on page 67 for more information): Press the Menu Select button directly below Optn. Press the Menu Select button directly below Impt. The priority status icon appears beside the normal message icon on the label bar. Press the Menu Select button directly below Impt again. The priority status icon and the normal message icon disappear from the label bar. 70 English Appending a Priority Status and a Reply Request to a Text Message Procedure: After the outgoing message is composed (see Composing and Sending a New Text Message on page 67 for more information): Press the Menu Select button directly below Optn. D or U to Impt and press the Menu Select button directly below Impt to indicate the message as important. AND D or U to Rqrp and press the Menu Select button directly Managing Text Messages below Rqrp to request for a reply. The priority status and reply status icons appear beside the normal message icon on the label bar. Receiving a Text Message Note: Removing a Priority Status and a Reply Request from a Text Message When an outgoing message is indicated with priority status and reply status icons, follow the procedure below to remove these indicators. Procedure: Press the Menu Select button directly below Optn. U or D to Impt and press the Menu Select button directly Procedure: When you receive a message, press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox and go to Step3. OR Follow the procedure below. below Impt to remove the priority status icon. AND The new message icon appears and the display momentarily shows New msg. D or U to Rqrp and press the Menu Select button directly Press the Menu Select button directly below TMS to access the message. The display shows alias or ID with the sender of the latest received message on top. below Rqrp to remove the reply status icon. When you receive a message that is flagged with the ”Request Reply” icon, you must manually respond to the sender that you have received the message. The system will not automatically send back a notification that the radio has received such message. The priority status, reply status and normal message icons disappear from the label bar. Advanced Features 71 English Viewing a Text Message from the Inbox The Inbox can hold up to thirty (30) messages. Note: D or U to read the message if fills more than one Advanced Features screen. 72 Procedure: Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox screen and proceed to Step 4. OR Follow the procedure below. > or < (on the keypad mic.) to TMS. Press the Menu Select button directly below TMS to access the TMS feature screen. Press the Menu Select button below Inbox to view Inbox feature screen. The display shows alias or IDs, with the sender of the latest received message. While on the review message screen, press the Menu Select button directly below Rply, Del, or Back to access the option. • Select Rply to reply the message. English • Select Del to delete the message. • Select Back to return to the previous screen. Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 66 for more information. Note: The original date and time stamp, address and message content is automatically appended to the reply message. Procedure: D or U to the required aliases or ID and press the Menu Select button below Sel to view the message. Press the Menu Select button directly below Rply to reply to a message. D or U to NEW and press the Menu Select button directly below NEW. OR D or U to LIST and press the Menu Select button directly below LIST for a predefined message. OR D or U to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message. A blinking cursor appears on the screen. OR The predefined message appears on the Compose screen, with a blinking cursor at the end of it. Use the keypad to type or edit your message. Press < to move one space to the left. Press the Menu Select button directly below Optn once you have finished writing the message. D or U to Send and press the Menu Select button directly below Send to send the message. The display shows the Send Message screen and Sending msg. Advanced Features Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. Replying to a Received Text Message Press the Menu Select button directly below Back at any time to return to the previous screen. Note: You can append a priority message and/or a request reply to your message. Using the Priority Status and Request Reply Features on page 70 for more information. 73 English Accessing the Drafts Folder Managing Sent Text Messages This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in. Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list. Procedure: > or < (on the keypad mic.) to TMS. The Sent folder is capable of storing a maximum of ten (10) last sent messages. When the folder is full, the oldest text message in the folder is deleted when the 11th message comes in. Press the Menu Select button directly below TMS to access the TMS feature screen. Viewing a Sent Text Message D or U to DRFT and press the Menu Select button below DRFT. Advanced Features The display shows the first draft message. Press the Menu Select button directly below Edit, Del, or Back to access the option. • Select Edit to edit the message before sending it. • Select Del to delete the message. • Select Back to return to the previous screen. The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 66 for more information. Procedure: Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Follow the procedure below. > or < (on the keypad mic.) to TMS. Press the Menu Select button directly below TMS to access the TMS feature screen. D or U to Sent and press the Menu Select button below Sent. 74 English Press the Menu Select button directly below Optn, Del, or Back to access the option. • Select Optn to send to the message. • Select Del to delete the message. • Select Back to return to the previous screen. Note: The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 21 for more information. Sending a Sent Text Message Procedure: Press the Menu Select button directly below Optn while viewing the message. D or U to Send and press the Menu Select button directly below Send to send the message. Press the Menu Select button below Send or the PTT button to send the message. The display shows the Send Message screen and Sending msg. Press the Menu Select button directly below Back to return to the previous screen. Note: You can append a priority message and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 70 for more details. Advanced Features Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. D or U to scroll through the address list and highlight the required address. OR D or U to {Other recpnt} and press the Menu Select button below Edit. A blinking cursor appears in the Enter address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. 75 English Secure Operations Deleting Text Messages Procedure: From the Inbox, Draft, or Sent screen: D or U to scroll through the messages. Press the Menu Select button directly below Del to view the delete options. Press the Menu Select button directly below Curr to delete the current message. OR Press the Menu Select button directly below All to delete all the messages. Advanced Features 76 English Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message. Managing Encryption Note: Refer to the Key-Variable Loader (KVL) manual for equipment connections and setup. Loading a Single Encryption Key Procedure: Attach the KVL to your radio. Upon attaching the KVL, the radio display shows Keyloading. Press the Menu Select button below Target. Press the Menu Select button below Load. Press the Menu Select button below Key. D or U to required key. Press the Menu Select button below Load to load the key to your radio. 7 When the key has been loaded successfully, the radio sounds a short tone for single-key radios. Procedure: Attach the KVL to your radio. Press the Menu Select button below Target. Press the Menu Select button below Load. Press the Menu Select button below Group. D or U to required group. Press the Menu Select button below Load to load the key to your radio. Your mobile radio display shows Keyloading when it is loading key(s) from KVL. When the key has been loaded successfully, the radio sounds an alternating tone for multikey radios. This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. There are two types of multikey: • Conventional Multikey – The encryption keys can be tied (strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operatorselectable keys, operator-selectable keysets, and operatorselectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. • Trunked Multikey – If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operatorselectable key erasure. Advanced Features Loading the Group Encryption Keys Using the Multikey Feature 77 English Advanced Features Selecting an Encryption Key (Conventional Only) Enabling Secure Transmission Procedure: Procedure: > or < (on the keypad mic.) to Key. Press the Menu Select button directly below Key. The display shows the last user-selected and stored encryption key, and the available menu selections. > or < (on the keypad mic.) to Sec and press the Menu Select button directly below Sec. The display shows m and Monitor the mode to be sure it is not in use. Press PTT button to transmit. D or U to scroll through the encryption keys. OR Use the keypad to enter the number of the desired key. Press the Menu Select button directly below Sel to save the newly selected key and return to the Home screen. OR Press H, the PTT button, or the Menu Select button directly below Exit to exit. Note: 78 English If the selected key is erased, a momentary keyfail tone sounds and the display shows Key fail. OR If the selected key is not allowed, a momentary illegal key tone sounds and the display shows Illegal key. the current key if multi-key has been enabled. Note: If the selected channel is preprogrammed for clear-only operation – when you press the PTT button, an invalid mode tone sounds and the display shows Clear Tx only. The radio does not transmit until you disable the secure mode. The radio can be configured to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details. Accessing the Secure Feature Press the Menu Select button directly below Kset. The display shows the last user-selected and stored keyset, and the available keyset menu selections. D or U to scroll through the keysets. OR Use the keypad to enter the number of the desired keyset. Press the Menu Select button directly below Sel to save the newly selected keyset. The radio exits keyset selection and returns to the Home screen. Procedure: > or < (on the keypad mic.) to Sec. Press and hold the Menu Select button directly below Sec to display Secure feature screen. The display shows the Secure screen. Selecting a Keyset This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other. Every channel to which one of the original keys was tied now has the equivalent new key instead. Note: Press H, the PTT button, or the Exit menu selection to exit this menu at any time without changing the keyset selection. Procedure: > or < (on the keypad mic.) to Kset. Erasing the Selected Encryption Keys Advanced Features This feature allows you to erase all or selected encryption keys. Procedure: > or < (on the keypad mic.) to Eras. Press the Menu Select button directly below Eras. The display shows the last user-selected and stored encryption key, and the available menu selections. D or U to the desired encryption key. OR Use the keypad to enter the number of the desired key. Press the Menu Select button directly below All to delete all keys. OR 79 English Press the Menu Select button directly below Sngl to delete current shown key. OR Press the Menu Select button directly below Abrt to abort this screen and return to Home screen. Requesting an Over-the-Air Rekey This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. Advanced Features Procedure: > or < (on the keypad mic.) to Rekey. Press the Menu Select button directly below Rekey. Press the PTT button to send the rekey request. OR Press the PTT button again, or the H or Emergency button, to exit the feature and transmit in normal mode. If the rekey operation fails, a bad-key tone sounds and the display shows Rekey fail. Note: 80 English The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. MDC Over-the-Air Rekeying (OTAR) Page This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgements, and Powerup Acknowledgements. Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly. Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Infinite UKEK Retention This feature enables Unique Key Encryption Key (UKEK) to be permanently stored in the radio even when all of the encryption keys is erased. Without this UKEK key, the radio could not be over the air rekeyed. Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Hear Clear 1 Companding: Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. • Compressor – reduces the background noise flow and the speech signal at transmitting radio. • Expander – expands the speech while the noise flow remains the same at receiving radio. 2 Random FM Noise Canceller (Flutter Fighter): Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode. Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. This feature uses information from the Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your radio, expressed as latitude and longitude. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature. For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. Advanced Features There are two components of Hear Clear. The Global Positioning System (GPS) Understanding the GPS Feature The GPS technology uses radio signals from earth orbiting satellites, to establish the location co-ordinates, maximizing your view of clear unobstructed sky is essential for optimum performance. Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of your radio will not work. Such situations include but are not limited to: • In underground locations • Inside of buildings, trains, or other covered vehicles 81 English • Under any other metal or concrete roof or structure • Between tall buildings or under dense tree-cover • In temperature extremes outside the operating limits of your radio Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher. Advanced Features Note: Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20 meters from your actual location, but sometimes further away. Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites. Note: 82 English The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of Defense GPS user policy and the Federal Radio Navigation Plan. These changes may affect the performance of the GPS feature on your radio. Enhancing GPS Performance Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, please note the following guidelines: • For your initial fix, hold the radio in the face position. • Stay in the open. The GPS feature works best where there is nothing between your radio and a large amount of open sky. The Outdoor Location Feature (Using GPS) This feature allows you to determine your current location using a location menu, as well as your current distance and bearing in relation to another location. Radio location may be requested and reported over-the-air. Your radio stores up to a maximum of sixty (60) programmable location coordinates, also known as waypoints. When the memory is full, the next waypoints automatically replaces the oldest waypoints in the radio. The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted. Preprogrammed Waypoints Fixed location coordinates: User-configurable location coordinates. • Home An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system administrator. Procedure: • Emergency > or < (on the keypad mic.) to Loc. • Last Known Location Press the Menu Select button directly below Loc. The display shows Location off . Press the Menu Select button directly below On to turn on the GPS. The display shows Previous loc . U or D to check the longitude, time and date of the last • Destination Only the alias is editable, not the coordinates. The Home and Destination coordinates are editable. Coordinates can be deleted one at a time, or all at once. Coordinates cannot be deleted. Note: Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Advanced Features Programmable Waypoints Accessing the Outdoor Location Feature successful location fix. Press the Menu Select button directly below Rfsh to obtain a new location fix. The top line temporarily displays Please wait while the new location is being determined. While the new location is being determined, the location signal can be a solid or blinking icon. Once the location coordinates are fixed, the display shows the current latitude. Toggle to see the longitude, time and date. The location coordinates are updated automatically every five seconds while the location signal is present. Press the Menu Select button directly below Exit to exit the feature and return to the main screen. 83 English OR Press H or the PTT button (if preprogrammed) to exit this menu. Saving a Waypoint Procedure: While in the current location display: OR Follow the procedure below to turn off the GPS (This feature is enabled by a qualified radio technician.): > or < (on the keypad mic.) to Loc. Press the Menu Select button directly below Loc. The display shows Previous loc . U or D to check the longitude, time and date of the last Press the Menu Select button directly below Optn. U or D U or D to Save as home and press the Menu Select button directly below Sel and proceed to Step 5. OR U or D to Save as dest. and press the Menu Select Advanced Features successful location fix. 84 Press the Menu Select button directly below Optn. > or < (on the keypad mic.) to Turn off GPS (if to Save as waypt and press the Menu Select button directly below Sel. OR button directly below Sel and proceed to Step 5. A blinking cursor appears in the screen. Use the keypad to type the alias via multi-tap. preprogrammed). Press < to move one space to the left. Press the Menu Select button directly below Sel to turn off the GPS. The display shows Location off. Press the Menu Select button directly below Exit to exit the feature and return to the main screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. The radio also exits the menu if the emergency button is pressed. English Press the Menu Select button directly below OK once you are done. 5 Viewing a Saved Waypoint Press H or the PTT button (if preprogrammed) to exit this menu. Press the Menu Select button directly below Optn. > or < (on the keypad mic.) to Waypoints. Press the Menu Select button directly below Sel. D or U to desired waypoint. Press the Menu Select button directly below Optn. The display shows View. Press the Menu Select button directly below Sel. D or U again to view longitude, time and date the waypoint Procedure: While in the current location display: Advanced Features The display shows Saved as . OR The display shows Saved as home. OR The display shows Saved as dest.. was detected. Press the Menu Select button directly below Back to return to previous Waypoint screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. 85 English Press the Menu Select button directly below Cncl to return to the Waypoints main screen. Editing the Alias of a Waypoint Procedure: Advanced Features While in the current location display: 86 The display shows updated. 10 Press H or the PTT button (if preprogrammed) to exit this menu. Press the Menu Select button directly below Optn. > or < (on the keypad mic.) to Waypoints. Press the Menu Select button directly below Sel. D or U to desired waypoints. Press the Menu Select button directly below Optn. D or U to Edit name and press the Menu Select button Press the Menu Select button directly below Optn. directly below Sel. > or < (on the keypad mic.) to Waypoints and press the A blinking cursor appears in the Edit Name screen. Use the keypad to edit the alias. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. Press the Menu Select button directly below OK once you are done. OR English Editing the Coordinates of a Waypoint Procedure: While in the current location display: Menu Select button directly below Sel. D or U to desired waypoints. Press the Menu Select button directly below Optn. D or U to Edit location and press the Menu Select button The first number blinks. directly below Sel. Press < to move to the previous number/coordinates. Press > to move to the next number/coordinates. Press U or D to change the North (N), South (S), East (E) or West (W) direction. Press the Menu Select button below Edit to change the number/coordinates. A blinking cursor appears in the Edit location screen. Procedure: Press < to move one space to the left. While in the current location display: Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press the Menu Select button directly below Optn. > or < (on the keypad mic.) to Waypoints. Press the Menu Select button directly below OK once you are done. OR Press the Menu Select button directly below Cncl to return to the previous screen. Press the Menu Select button directly below Sel. D or U to desired waypoints. Press the Menu Select button directly below Optn. OR Press the Menu Select button directly below Del and then skip to step 7. D or U to Delete and press the Menu Select button Press the Menu Select button directly below OK once you are done with the new coordinates. OR Press the Menu Select button directly below Cncl to return to the previous screen then skip to step 11. 10 The display shows {Home} Updated and the radio returns to the Waypoints main screen. OR The display shows {Destination} Updated and the radio returns to the Waypoints main screen. 11 Press H or the PTT button (if preprogrammed) to exit this menu. Advanced Features Deleting a Single Saved Waypoint directly below Sel. The display shows confirm del?. Press the Menu Select button directly below Yes to delete. The display shows deleted. OR Press the Menu Select button directly below No to return to previous Waypoint screen. Press H or the PTT button (if preprogrammed) to exit this menu. 87 English Deleting All Saved Waypoints Measuring the Distance and Bearing from a Saved Waypoint Procedure: Press the Menu Select button directly below Optn. > or < (on the keypad mic.) to Waypoints and press the Menu Select button directly below Sel. D or U to desired waypoints and press the Menu Select Procedure: While in the current location display: Press the Menu Select button directly below Optn. D or U to Dist frm here and press the Menu Select button directly below Sel. button directly below Optn. D or U to Delete all and press the Menu Select button Advanced Features directly below Sel. The display shows All saved wayp confirm del?. Press the Menu Select button directly below Yes to delete. The display shows All saved wayp deleted. OR Press the Menu Select button directly below No to return to previous Waypoint screen. Press H or the PTT button (if preprogrammed) to exit this menu. 88 English D or U to the required waypoint, and press the Menu Select button directly below Sel. The display shows the distance and bearing from the current to the selected coordinates. Press the Menu Select button directly below Back to return to the previous Waypoint screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. Trunking System Controls Using the Location Feature While in Emergency Mode However, you may re-enter the Location menu while still in emergency mode, provided that Silent Emergency has not been activated. If you have turned Location off using the ON/OFF menu key, it automatically turns back on when Emergency is activated. If there is a solid location signal during Emergency, the current location and the location information received is saved as Emergency and Last Known Location waypoints, respectively. Using the Failsoft System The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. The failsoft condition is indicated by a faint beeping tone every nine seconds (radio unsquelched) until the trunking system returns to normal operation. To continue, in Failsoft, to communicate with other talkgroups, refer to the following procedure. Advanced Features When the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the home (default) display so that you can see which channel the emergency signal is going out on. Procedure: Rotate the MFK to change to a different repeater frequency. Press the PTT button to talk, and release the button to listen. When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. 89 English Going Out-of-Range SmartZone® OUT OF RANGE when your radio goes out of the range of the system, it can no longer lock onto a control channel. The SmartZone® feature extends communications beyond the reach of a single-trunked site (antenna location) when operating in a SmartZone system. SmartZone units provide expanded wide-area coverage. Advanced Features Procedure: A low-pitched tone sounds. AND/OR The display shows the currently selected zone/channel combination and Out of range. Your radio remains in this out-of-range condition until: It locks onto a control channel. OR It locks onto a failsoft channel. OR It is turned off. 90 English SmartZone automatically switches the radio to a different site when the current site signal becomes unacceptable. This usually happens when the vehicle in which the radio is located is driven out of the range of one site, and into the range of another. Under normal conditions, a SmartZone-enabled radio functions invisibly to the operator. However, the operator does have some manual controls on the Control Head – the RSSI menu entry. This button can be used to check, or change, the SmartZone operation. Using Site Trunking Feature If the zone controller loses communication with any site, that site reverts to site trunking. The display shows the currently selected zone/channel combination and Site trunking. Note: When this occurs, you can communicate only with other radios within your trunking site. Viewing and Changing a Site This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. This feature allows you to view the number of the current site or force your radio to change to a new one. Procedure: Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. OR Follow the procedure below. Procedure: > or < (on the keypad mic.) to Site. Press the Menu Select button directly below Site. Press the Menu Select button directly below Lock to lock the site. OR Press the Menu Select button directly below Unlk to unlock the site. The radio saves the new site lock state and returns to the Home screen. Viewing the Current Site Press the preprogrammed Site Search button. OR > or < (on the keypad mic.) to RSSI. The display momentarily shows the name of the current site and its corresponding received signal strength indicator (RSSI). Advanced Features Locking and Unlocking a Site 91 English Changing the Current Site Trunked Announcement Procedure: The announcement capability allows you to make announcements to the entire user group, as well as monitor talkgroup calls and other announcements. Press and hold down the preprogrammed Site Search button. OR Press and hold down the Menu Select button directly below RSSI. A tone sounds and the display momentarily shows Scanning site. Advanced Features When the radio finds a new site, it returns to the Home screen. 92 English Announcement calls are handled in two different ways, depending on the trunked central controller configuration. The two types are called ruthless and non-ruthless preemption. • Ruthless Preemption: When a ruthless preemption announcement call is initiated, the requesting radio begins transmitting immediately. All associated talkgroup calls taking place on other channels are immediately halted, and the radios are steered to the announcement call. Transmitting radios continue to transmit until the PTT button is released, at which time they also unmute for the announcement call. Individual calls (Private Conversation and telephone interconnect) are not affected. • Non-Ruthless Preemption: When a non-ruthless preemption announcement is initiated, the initiating unit receives a telephone-type busy tone, followed by a call back when all associated talkgroup conversations end. Once an announcement call is pending, any attempts by other users to initiate a talkgroup call will result in a telephone-type busy tone. These users will not receive a call back until the announcement call is complete. Initiating an Announcement Procedure: If channel is set as the primary mode, turn the MFK to locate the announcement-group mode. Press the microphone PTT button to initiate the announcement. This feature allows the user to select the radio’s functionality based on the Ignition State of the radio user’s vehicle. The available options are as follows. Blank This option allows the user to power on and power off the radio through the Power button regardless of the Ignition’s current state. Tx Inhibit Advanced Features If your radio has been programmed to allow announcement calls: Ignition Switch Options This option allows the user to power on and power off the radio through the Power button regardless of the Ignition’s current state. In addition, if the Ignition is not present, then all transmissions are inhibited. This includes receiving any Trunking dispatch communications since the radio will not affiliate with the Trunking systems. PTT Tx Inhibit This option allows the user to power on and power off the radio through the Power button regardless of the Ignition’s current state. In addition, if the Ignition is not present, then all PTT button transmissions are inhibited. However, the radio is able to affiliate with the Trunking systems. 93 English Required This option allows the user to power on the radio only if the Ignition is present. The radio can be powered off either through Power button press or when Ignition is lost. In addition, the radio automatically powers on when the Ignition is present only if the radio was turned off due to the ignition being removed. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Advanced Features Soft Power Off This option allows the user to power on the radio either through Power button presses or when the Ignition is detected. Meanwhile, if the Power button was pressed or the Ignition was removed, the radio will be turned off. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Ignition Only Power Up This option allows the user to power on the radio only when Ignition is detected and will power off when it is removed. The radio does not power on or off with the Power button press. 94 English This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Note: While "Ignition" is not present, the radio powers-off with a radio-user Power Off button / knob selection if the radio was powered-up with an Emergency Power Up footswitch-press or Ignition Auto Power Off timer is running. While "Ignition" is present, the radio powers-on with a radio-user Power On button / knob selection only if the radio was powered-down with Inactivity Auto Power Off timer. Emergency Power Up This feature allows the user to power on the radio and automatically transmits an emergency mode transmission on personalities with emergency enabled, with the use of a footswitch. In addition, when the Ignition Switch option is set to either Tx Inhibit or PTT Tx Inhibit, this feature will not be available to the users. Press the footswitch to turn on the radio and launch Emergency. A tone sounds and the display shows Emergency. Utilities Auto Power Off Timer Inactivity Auto Power Off Timer – This timer begins once the radio is power-on. While the timer is active any user interaction with the radio resets the timer. Ignition Auto Power Off Timer – This timer begins once the vehicle key is removed, when the voltage at the ignition sense is removed. While the timer is active any user interaction with the radio resets the timer. When the vehicle key is reapplied, the voltage at the ignition is reconnected, this timer is stopped. Although both Inactivity Auto Power Off and Ignition Auto Power Off can be enabled together, Ignition Auto Power Off timer is mutually exclusive with Inactivity Auto Power Off timer when both are enabled. During the last two minutes of the timer countdown, the radio generates continuous low tone and blinks Powering off warning on the display until the timer expires or the timer is reset. The radio automatically powers off after the timer expires. The duration of the timer is preprogrammed. Viewing Recent Calls List This feature allows you to view the recent incoming and outgoing call information of the following call types: • Call Alert • Selective Call • Private Call • Phone Call (Outgoing only) Note: The radio can also be preprogrammed to log the radio IDs associated with incoming Dispatch Calls. Check with your dealer or system administrator for more information. Advanced Features Auto Power Off feature powers off the radio when no user actions occur during a preprogrammed length of time. There are two different versions of Auto Power Off: Procedure: > or < (on the keypad mic.) to Rcnt. Press the Menu Select button directly below Rcnt to access the Recent Calls feature screen. D or U to scroll through the list. Press the Menu Select button directly below Back to return to Home screen. OR Press H or the PTT button to return to the Home screen. 95 English If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Selecting the Power Level You can select the power level at which your radio transmits. The radio always turns on to the default setting. Note: This feature must be preprogrammed by a qualified radio technician. Advanced Features Settings: Selecting a Radio Profile This feature allows you to manually switch the visual and audio settings of the radio. The display, backlight, alert tones, and audio settings are defined according to the preprogrammed radio settings of each radio profile. Please refer to a qualified technician for more information. Note: • Select Low for a shorter transmitting distance and to conserve power. • Select High for a longer transmitting distance. Procedure: Use the preprogrammed Transmit Power Level Switch to toggle transmit power level between high and low. OR Follow the procedure below. > or < (on the keypad mic.) to Pwr. Press the Menu Select button directly below Pwr. 96 English The display shows Low power and the low power icon. OR The display shows High power and the high power icon. If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure: Use the preprogrammed Profile button and proceed to Step 3. OR Follow the procedure below. > or < (on the keypad mic.) to Prfl. Press the Menu Select button directly below Prfl to access the Profiles feature screen. D or U to scroll through the menu selections. Press the Menu Select button directly below Sel to select the required radio profile. Turning Keypad Tones On or Off The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile. Procedure: Controlling the Display Backlight You can enable or disable the radio’s display backlight as needed, if poor light conditions make the display difficult to read. Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radio’s display. Procedure: Note: Press the Dimmer button to adjust the brightness of the display. Long press to toggle between day and night mode. You can enable and disable keypad tones as needed. Press the preprogrammed Keypad Mute button to turn the tones on or off. OR Follow the procedure below. > or < (on the keypad mic.) to Mute. Press the Menu Select button directly below Mute. The display momentarily shows Tones off, indicating that the keypad tones are disabled. OR The display momentarily shows Tones on, and a short tone sounds, indicating that the keypad tones are enabled. Advanced Features OR Press the Menu Select button directly below Exit to exit the screen without making any changes. 97 English Turning Voice Mute On or Off Using the Time-Out Timer You can enable and disable voice muting of the affiliated trunking talkgroup or selected conventional channel as needed. This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting. Procedure: Press the preprogrammed Voice Mute button to turn the feature on or off. OR Follow the procedure below. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. > or < (on the keypad mic.) to VMut. The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. Press the Menu Select button directly below VMut. Note: The display momentarily shows Voice mute off, and a short tone sounds, indicating that the feature is disabled. OR The display momentarily shows Voice mute on, and a short tone sounds, indicating that the feature is enabled. Advanced Features 98 English You will hear a brief, low-pitched, warning tone four seconds before the transmission times out. Procedure: Hold down the PTT button longer than the preprogrammed time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LEDs goes out until you release the PTT button. Release the PTT button. The LEDs relight and the timer resets. Press the PTT button to re-transmit. The time-out timer restarts and the red LED lights up. Using the Conventional Squelch Operation Features Procedure: > or < (on the keypad mic.) to Sql. Press the Menu Select button directly below Sql. The display shows Squelch XX, where XX is the value for the current squelch. Press the Menu Select button directly below “+” to increase the squelch volume. OR Press the Menu Select button directly below “-” to decrease the squelch volume. Press H to return to the selected channel. Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Option Result Carrier squelch (C) You hear all traffic on a channel. PL or DPL The radio responds only to your messages. Digital Options One or more of the following options may be preprogrammed in your radio. Consult your dealer or system administrator for more information. Option Advanced Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Analog Options Result Digital Carrier-Operated Squelch (COS) You hear any digital traffic. Normal Squelch You hear any digital traffic having the correct network access code. Selective Switch You hear any digital traffic having the correct network access code and correct talkgroup. 99 English Using the PL Defeat Feature Using the Smart PTT Feature (Conventional Only) This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. Procedure: Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel. OR The radio is muted if no activity is present. When smart PTT is enabled in your radio, you cannot transmit on an active channel. Note: When this feature is active, the Carrier Squelch status indicator is displayed. If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy. Three variations of smart PTT are available: Advanced Features Mode Using the Digital PTT ID Feature This feature allows you to the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher. Your radio’s ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radio’s ID is sent continuously during the voice message. 100 English Description Transmit Inhibit on Busy Channel with Carrier You cannot transmit if any traffic is detected on the channel. Transmit Inhibit on Busy Channel with Wrong Squelch Code You cannot transmit on an active channel with a squelch code or (if secureequipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented. Quick-Key Override This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. Accessing General Radio Information • Radio Information • IP Display Note: • Control Assignments Note: Model Number ESN Flash Code Tuning Version If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Accessing Radio Information • • • • Serial Number Flash Size & Type RF Band Processor Version Press H at any time to return to the Home screen. Procedure: > or < (on the keypad mic.) to Info. Press the Menu Select button directly below Info. U or D to Radio info and press the Menu Select button directly below Sel. This feature displays the following information of your radio: The display shows the Information screen. • Host Version • Secure Version • CH 1 – 4 Version (depending on the number of channels connected.) D or U to scroll through the various information. OR Press the Menu Select button directly below Back to return to previous screen. OR Press H to exit and return to the home display. • • • • • • • • • • • • • DSP Version KG (Secure Algorithm) Serial Number MCHIB Version CHIB Version AUX CH Version TIB Version Siren Version TRC Version VRS Version URC Version DVRS App Version (only when DVRS is available) DVRS DSP Version (only • DVRS CP Version (only when when DVRS is available) DVRS is available) Advanced Features Your radio contains information on the following: • • • • 101 English Viewing IP Information Viewing Control Assignments This feature displays the device name, IP address, and status of your radio. This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel. Advanced Features Note: The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information. See Programmable Features on page 7 for more information on the various programmable features of your radio. Procedure: Procedure: Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. > or < (on the keypad mic.) to Info. Press the Menu Select button directly below Info. D or U D or U to scroll through the various information. OR Press the Menu Select button directly below Back to return to previous screen. OR Press H to exit and return to the Home display. > or < (on the keypad mic.) to Info. Press the Menu Select button directly below Info. D or U D or U to scroll through the various information. to Ip info and press the Menu Select button directly below Sel. OR Press the Menu Select button directly below Back to return to previous screen. OR Press H to exit and return to the Home display. 102 English to Control map and press the Menu Select button directly below Sel. Using Keypad as Light Type Selector Your radio supports siren and light via the keypad microphone. The keypad microphone can be preprogrammed to enable siren, public address and light. The keypad can be preprogrammed as different types of light. Each button can be preprogrammed as a different light. For example, pressing the preprogrammed button turns on the light. Using Keypad as Siren Type Selector The keypad can be preprogrammed as different types of siren. Each button can be preprogrammed as a different siren tone. For example, pressing the preprogrammed button turns on the siren. Procedure: Press the preprogrammed light button to turn on the light. Press a different preprogrammed light button to change the light. OR Press the same preprogrammed button to turn off the light. Procedure: Press the preprogrammed siren button to turn on the siren. The display shows Siren on. Press a different preprogrammed siren button to change the siren tone. OR Press the same preprogrammed button to turn off the siren. Using the Public Address Button on the Keypad Advanced Features Using Siren, PA and Light The keypad can be preprogrammed to enable the radio’s internal public address (PA) system. Procedure: Press the preprogrammed public address button to turn on the public address feature. The display shows PA on. Press the preprogrammed public address button to turn off the public address feature. When the internal public address and siren feature are turned on at the same time, the display shows Siren/PA on. 103 English Using the External Public Address Button on the Keypad The keypad can be preprogrammed to enable the radio’s external public address (PA) system. This button enables the external speaker to be able to transmit the radio user announcement publicly. Advanced Features Procedure: Press the preprogrammed public address button to turn on the public address feature. The display shows Ext Rad on. Press the preprogrammed public address button to turn off the public address feature. When the external public address and internal public address feature is turned on at the same time, the display shows Ext Rad/PA on. 104 English Using Optional External Alarms (Horn and Lights) All control heads can be equipped for external alarms (horn and lights) that are activated when a Call Alert page, Private Conversation call, or phone call is received. The radio always powers up with the horn and lights feature enabled. Note: The horn and lights feature must be enabled by a qualified radio technician. Using Non-Permanent Horn and Lights Procedure: Press the Menu Select button directly below H/L momentarily. The last selected alarm(s) are enabled, and the display shows the enabled alarm(s) alternating with the selected mode, until it is turned off. Press the Menu Select button directly below H/L momentarily to turn off the alarm(s). The display shows Horn/Lites off. Changing the Selected Alarms If Permanent Horn and Lights is enabled, horn and lights will automatically be turned on when the radio powers up. Procedure: Press the Menu Select button directly below H/L until the display shows the required alarm. Press the Menu Select button directly below the required entry and the display exits to Home screen. Procedure: Press the Menu Select button directly below H/L once to turn off the alarm(s). Press the Menu Select button directly below H/L momentarily to enable the last selected alarm(s). The display briefly shows the enabled alarms, and then reverts back to the selected mode. Press the Menu Select button directly below the entry activates the option. Below are the selections available. • Select H+L to turn on both horn and lights. The display shows Horn/Lites on. • Select Lgts to turn on the lights. The display shows Lights on. Advanced Features Using Permanent Horn and Lights • Select Horn to turn on the horn. The display shows Horn on. An Off entry is shown at the softkey when one of the features above is active. Selecting the Off deactivates the current active alarm. 105 English Receiving a Call While Alarms are Turned On Turning Off Rearmable External Alarms When you receive a call with the Alarms turned on: Procedure: Procedure: You hear the vehicle’s horn sounds for four seconds, and/or the car lights turn on for 60 seconds. The display shows the type of call received (Call, Page, or Phone) and the selected mode name. The time interval can be modified by a qualified radio technician. Advanced Features Turning Off Non-Rearmable External Alarms Procedure: Press the Menu Select button directly below Call, Page or Phon will turn off the external alarm(s) and place you directly in that feature. OR Press the PTT button or any control-head button to turn off the external alarm(s). Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature. The Volume Knob and the Dimmer button have no effect on the state of the external alarm(s). 106 English Press the Menu Select button directly below Call, Page or Phon to turn off the external alarm(s) and place you directly in that feature. The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on. OR Press the PTT button or any control head button other than the Menu Select button directly below H/L to turn off the external alarm(s). The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on. OR Press the Menu Select button directly below H/L to turn off the external alarm(s) and exit the Horn and Lights feature. Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature. The Volume knob and the Dimmer button have no effect on the state of the external alarms. Using the Voice Announcement • High – enables the voice of the feature to announce even when the radio is receiving calls. • Low – disables the voice of the feature from announcing when the radio is receiving calls. Each voice announcement is within a limit of three seconds maximum. The sum total duration for all voice announcements in a radio shall be no more than 1000 seconds. Procedure: Note: • The radio powers up. The radio announces the current zone and channel it is transmitting. This feature must be preprogrammed by a qualified radio technician. The features which Voice Announcement supports are: • • • • • Zone Scan Talkaround/Direct Emergency On Secure/Clear Note: • • • • • Channel Monitor (Conventional) Tx Inhibit In-Call User Alert (Voice Mute) Multi Functional Button Voice announcements support certain number of zone-channel, but not all. You hear a voice announcement when the features below are preprogrammed in the radio. • Press the preprogrammed voice announcement button (which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting. Note: Advanced Features This feature enables the radio to audibly indicate the current feature mode, Zone or Channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. The two options of priority for the Voice Announcement available are: Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority. All the three programmable buttons at the side of the radio support this feature. Seek advice from your dealer or qualified technician for the best selections for this feature. 107 English • Change to a new zone. The radio announces the current zone and channel it is transmitting. • Change to a new channel within the current zone. The radio announces the current channel. • Press either the Menu Select button or preprogrammed button of the radio to launch or terminate Scan, Monitor, Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation or deactivation. Helpful Tips The following are suggestions to assist you in troubleshooting possible operating problems. Advanced Features Caution 108 English The cables that connect to the rear of the radio could have live voltage on some of their pins. Do not remove or reconnect these cables. Only a qualified radio technician should perform this task. Service performed by unauthorized personnel may cause the radio to transmit an emergency alarm even if the unit is turned off. If your radio is locked up or the display shows FAIL 01/09, turn the radio off and then back on. If this does not correct the condition, take the radio to a qualified radio technician for service. If radio operation is intermittent, check with other persons using the system for similar problems before taking the radio in for service. Similar problems indicate a system malfunction rather than a radio failure. If symptoms persist or, if your unit exhibits other problems, contact a qualified radio technician. Accessories http://www.motorolasolutions.com/APX On the website, search for APX Mobile Radios. You will see the accessories information besides the specifications of the radio. You can also contact your dealer for details. Accessories For a list of Motorola-approved antennas and other accessories, visit the following website: 109 English Appendix: Maritime Radio Use in the VHF 110 Appendix: Maritime Radio Use in the VHF Frequency Range Take a moment to review the following: Special Channel Assignments. . . . . . . . . . . . . . . . . . page 110 Operating Frequency Requirements . . . . . . . . . . . . . .page 111 Declaration of Compliance for the Use of Distress and Safety Frequencies . . . . . . . . . . . . . . . . . . . . . . page 113 Technical Parameters for Interfacing External Data Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 113 Special Channel Assignments Emergency Channel If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order: “MAYDAY, MAYDAY, MAYDAY.” “THIS IS _____________________, CALL SIGN __________.” State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. English Repeat “MAYDAY” and the name of the vessel. “WE ARE LOCATED AT _______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.: • latitude and longitude • bearing (state whether you are using true or magnetic north) • distance to a well-known landmark • vessel course, speed or destination State the nature of the distress. Specify what kind of assistance you need. State the number of persons on board and the number needing medical attention, if any. Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. “OVER.” 10 Wait for a response. 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Non-Commercial Call Channel Operating Frequency Requirements A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows: • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency • on ships subject to the Safety Convention, the radio must be capable of operating: a. in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.425 MHz frequency band, and b. in the semiduplex mode on the two frequency channels specified in the table below. Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Table A-1: VHF Marine Channel List Frequency (MHz) Channel Number Transmit Receive 10 11 12 13** 14 15** 16 17** 18 19 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 156.900 156.950 160.650 160.700 160.750 160.800 160.850 – 160.950 – 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 161.500 161.550 Appendix: Maritime Radio Use in the VHF For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. 111 English Appendix: Maritime Radio Use in the VHF Table A-1: VHF Marine Channel List (Continued) 112 Frequency (MHz) Channel Number Transmit Receive 20 22 24 25 26 27 28 60 62 63 65 66 67** 68 69 71 72 73 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 161.600 161.650 161.700 161.750 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 156.575 – 156.675 English Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit Receive 74 75 76 77** 78 79 80 84 85 86 87 88 156.725 *** *** 156.875 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 157.375 157.425 156.725 *** *** – 161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.875 161.925 161.975 162.025 * Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. ** Low power (1 W) only *** Guard band Note: A – in the Receive column indicates that the channel is transmit only. Declaration of Compliance for the Use of Distress and Safety Frequencies Technical Parameters for Interfacing External Data Sources Input Voltage (Volts Peak-to-peak) Max Data Rate Impedance RS232 USB SB9600 18V 3.6V 5V 28 kb/s 5k ohm 12 Mb/s 90 ohm 9.6 kb/s 120 ohm Appendix: Maritime Radio Use in the VHF The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3. 113 English Term Glossary Carrier Squelch Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise”. Central Controller A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters. This glossary is a list of specialized terms used in this manual. Glossary Term Definition Definition ACK Acknowledgment of communication. Active Channel A channel that has traffic on it. Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature. ARS Automatic Registration Service ASTRO 25 Trunking Motorola standard for wireless digital trunked communications. Channel ASTRO Conventional Motorola standard for wireless digital conventional communications. A group of characteristics such as transmit/ receive frequency pairs, radio parameters, and encryption encoding. CHIB Control Head Interface Board Autoscan A feature that allows the radio to automatically scan the members of a scan list. AUX CH Auxiliary Control Head Call Alert Privately page an individual by sending an audible tone. 114 English In a trunking system, one of the channels that is used to provide a continuous, twoControl Channel way/data communications path between the central controller and all radios on the system. Conventional Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking). Conventional Scan List A scan list that includes only conventional channels. Term Definition Term Definition Codeplug Cursor A visual tracking marker (a blinking line) that indicates a location on the display. Failsoft Deadlock Displayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt. A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft. FCC Federal Communications Commission. FM Frequency Modulation Hang Up Disconnect. Home screen The first display information after the radio completes its self test. KVL Key-variable loader: A device for loading encryption keys into the radio. LCD Liquid crystal display LED Light-emitting diode Menu Entry A software-activated feature shown at the bottom of the display – selection of these MCHB Millennium Control Head Board Digital Private Line (DPL) A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone. Digital Signal An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. Dispatcher An individual who has radio system management duties. DSP Digital Signal Processing DVRS Digital Vehicular Repeater System Dynamic Regrouping A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. ESN Electrical Serial Number Glossary CP features is controlled by the g. 115 English Term Definition Monitor Check channel activity through menu entries. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed. Multi-System Talkgroup Scan List A scan list that can include both talkgroups (trunked) and channels (conventional). Glossary Network Access Code (NAC) operates on Network Access digital channels to reduce voice channel Code interference between adjacent systems and sites. Non-Tactical/ Revert The user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel. OTAR Over-the-air rekeying. Page A one-way alert, with audio and/or display messages. Personality A set of unique features specific to a radio. PIN Personal Identification Number Preprogrammed Refers to a software feature that has been activated by a qualified radio technician. 116 English Term Definition Private (Conversation) Call A feature that lets you have a private conversation with another radio user in the talkgroup. Private Line (PL) A sub-audible tone that is transmitted such that only receivers decoding the tone receives it. Programmable Refers to a radio control that can have a radio feature assigned to it. PTT Push-To-Talk – the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. Radio Frequency (RF) The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz). Repeater A conventional radio feature, where you talk through a receive/transmit facility that re-transmits received signals, in order to improve communications range and coverage. Selective Call A feature that allows you to call a select individual, intended to provide privacy and to eliminate the annoyance of having to listen to conversations of no interest to you. Term Definition Squelch Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data. Status Calls Pre-defined text messages that allow the user to send a conditional message without talking. Tactical/ Non-Revert The user talks on the channel that was selected before the radio entered the emergency state. Talkaround Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications. Talkgroup An organization or group of radio users who communicate with each other using the same communication path. TMS Text Messaging Service Definition Trunking The automatic sharing of communications paths between a large number of users (see Conventional). Trunking Priority Monitor Scan List A scan list that includes talkgroups that are all from the same trunking system. USK Unique Shadow Key UTC Coordinated Universal Time. The international time standard (formerly Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, England, which is located at 0 degrees longitude. Everything east of Greenwich (up to 180 degrees) is later in time; everything west is earlier. There are 42 time authorities around the world that are constantly synchronizing with each other. Abbreviated as UTC (English backronym = Universal Time, Coordinated), it is also known as Zulu (Z) Time. VRS Vehicular Repeater System Zone A grouping of channels. Glossary Any digital P25 traffic having the correct Selective Switch Network Access Code and the correct talkgroup. Term 117 English Commercial Warranty and Service Limited Warranty Commercial Warranty and Service MOTOROLA COMMUNICATION PRODUCTS 118 I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: MOTOROLA SOLUTIONS INC. (“MOTOROLA”) warrants the MOTOROLA manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below: MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS: APX Mobile Radio One (1) Year Product Accessories One (1) Year MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the English Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE: You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER: A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. Commercial Warranty and Service III. STATE LAW RIGHTS: C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D)Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G)Rechargeable batteries if: • any of the seals on the battery enclosure of cells are broken or show evidence of tampering. • the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H)Freight costs to the repair depot. I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. 119 English Commercial Warranty and Service VI. PATENT AND SOFTWARE PROVISIONS: MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following: A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim; B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C)should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. 120 English MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW: This Warranty is governed by the laws of the State of Illinois, U.S.A. VIII. FOR AUSTRALIA ONLY: Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Motorola Solutions Australia’s limited warranty below is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: http://www.motorola.com/Business/XA-EN/Pages/ Contact_Us#support_tab for the most updated warranty terms. Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for a period of three years from the date of shipment from the factory, or the date of delivery if purchased from an authorized Motorola twoway radio dealer. For more information about ESP, contact the Motorola Radio Support Center, 2204 Galvin Drive, Elgin, IL 60123, 1-800-227-6772. Commercial Warranty and Service This warranty is given by Motorola Solutions Australia Pty Limited (ABN 16 004 742 312) of Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. SERVICE 121 English Commercial Warranty and Service Notes 122 English Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, Illinois 60196 U.S.A. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2012, 2013 Motorola Solutions, Inc. All rights reserved. June 2013. *68012006035* 68012006035-C
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Motorola Solutions - GCD Penang Create Date : 2013:05:08 16:02:48Z Modify Date : 2013:05:08 16:12:32+08:00 Subject : User Guide Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Description : User Guide Title : APX Mobile O2 Control Head Creator : Motorola Solutions - GCD Penang Producer : Acrobat Distiller 11.0 (Windows) Creator Tool : FrameMaker 8.0 Metadata Date : 2013:05:08 16:12:32+08:00 Document ID : uuid:c170c7ec-437d-4d75-bbb9-ed566ad00a19 Instance ID : uuid:0701ff55-785c-4ef0-a431-28667de2a200 Page Mode : UseNone Page Count : 142 Signing Date : 2013:05:08 16:12:32+08:00 Signing Authority : ARE Acrobat Product v8.0 P23 0002337 Annotation Usage Rights : Create, Delete, Modify, Copy, Import, ExportEXIF Metadata provided by EXIF.tools