Napco Security Systems IBR Tablet User Manual

Napco Security Systems Inc Tablet IBR TOUCH IBR TOUCH WL WI2297LF 25 QUICK pub

a href="https://usermanual.wiki/Napco-Security-Systems" itemprop="url"> Napco Security Systems >

User manual

IBR-TOUCH & IBR-TOUCH-WL Quick Start Guide 1 © NAPCO 2018 WI2297LF preliminary draft # .25 4/18 NAPCO iBridge™ IBR-TOUCH & IBR-TOUCH-WL Touchscreen Tablets 1 Unpack the touchscreen tablet (look carefully for the sup-plied mounting hardware; the Power Adapter is only included withthe model IBR-TOUCH-WL)Note: If using older ISEE Series Cameras, use your existingISEE-WAP (with its power adapter and CAT5 cable, shown).IBR-TOUCH-WL Touchscreen Rear Case 2Mount the touchscreen rear case to the wall using screws appropriate for the mounting surface. Power must be provided with the IBR-TOUCH-WL using the 12VDC power adapter, observing polarity (use the wire hole located in the center of the rear case, shown below). The IBR-TOUCH connects to the Gemini security system 4-wire bus. 3Apply power to the control panel, the touchscreen and the ISEE-WAP / IBR-ZREMOTE / StarLink Connect radio. Upon power up, both touchscreens will start within about 5 seconds (both can be manu-ally powered by pressing and holding the small but-ton on the right side for 10 seconds). 4Upon power up, the Setup Wizard will automatically start. Follow the sequence of images as shown in the following steps, as necessary for the in-stallation type. If the Setup Wizard does not automatically start, press and hold the System Settings ("gear") icon, enter your Dealer password, then tap Setup Wizard. "center hole" for power or keypad bus wires CAT5 Cable ISEE-WAP Power Adapter Power Adapter Tap Yes and set the date, time and Time Zone (if necessary). IMPORTANT: Outdated digital certifi-cates will disallow connection to your iBridge or StarLink Connect system, as well as inhibiting nec-essary automatic firmware downloads. 5Wait for the system diagnostics process to complete. Functional components are marked with a check; items not configured or not enabled are marked with a "x". Selections are blank when the Setup Wizard is run for the first time. Tap Configure to continue. 6 . . System Settings button QUICK START GUIDE
2 IBR-TOUCH & IBR-TOUCH-WL Quick Start Guide If you have an ISEE-WAP with existing older iSeeVideo cameras, tap ISEE Series Cameras; if your system in-cludes the newer ISV2 models, tap ISV2 Series Cameras; for systems without cameras, tap No Cameras (cameras can always be added later). Note: ISEE and ISV2 camer-as cannot be combined. Select how the IBR-TOUCH / IBR-TOUCH-WL will be used. If it will only be used as a security system key-pad, tap Keypad Only (jump to step 9). To include video camera and Z-Wave functions, tap Full Func-tionality (and go to step 8). 7 8 9 10 Wait until the message indicates the connection tothe customer's wireless router is complete, thentap Next. 12 If you selected Keypad Only in step 7, the virtualsecurity system keypad will appear (shown be-low). Stop here -- you're finished! If you selected Full Functionality, you're almost finished...go to next step... 11 The system will then automatically try to connectto the "local" StarLink Connect radio or the iBridge (zRemote) Z-Wave Controller that is physically located "locally" (i.e. inside the prem-ises). When connected, tap Finish. To connect through the customer's wireless router, check Enable WiFi; select the router name* from the pull-down and have the customer type their router Password (click the "Refresh" button to the right of the pull-down if the custom-er's router is not listed). When finished, tap Save & Next. *Note: The default name "Public" is used with ISEE-WAP installations.
Download:
Mirror Download [FCC.gov]
Document ID3824864
Application ID8c506R1vQZNKoLXqa0YKdw==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize224.64kB (2808045 bits)
Date Submitted2018-04-22 00:00:00
Date Available2018-04-22 00:00:00
Creation Date2018-04-10 09:08:27
Producing SoftwareAcrobat Distiller 18.0 (Windows)
Document Lastmod2018-04-20 10:32:27
Document Title_IBR-TOUCH_&_IBR-TOUCH-WL_WI2297LF.25_QUICK.pub
Document CreatorPScript5.dll Version 5.2.2
Document Author: dblock
FCC ID Filing: AD8-IBR

Navigation menu