Nedap N V CONVEXS Inductive Proximity RFID Card Reader User Manual

N. V. Nederlandsche Apparatenfabriek NEDAP Inductive Proximity RFID Card Reader Convexs 80 series

a href="https://usermanual.wiki/Nedap-N-V" itemprop="url"> Nedap N V >

Contents

User manual 01

Date : 11 April 2011 Version: 7 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. © Nedap N.V., IDEAS P.O. Box 103 NL-7140 AC GROENLO The Netherlands Page 1 of 4 Part.no.: 5268656 48 28 28 41 8,5 4.5 Convexs 80 Nedap Mifare dual technology readers GENERAL The Convexs reader enables smooth migration to Mifare card technology in existing Nedap XS, Nedap AEOS and third party systems. The Convexs MN80 reads both Mifare and Nedap cards, the Convexs M80 Mifare cards only. The Convexs output can be set to either Wiegand, XS RF modulation or (encrypted) RS485 protocol. The Convexs MD80 reads Mifare DESFire cards. Functionality and output is determined by the configuration of the Convexs reader. The configuration is defined using the programm AEreco, and deployed by the configuration card or via AEmon. (More information about configurations can be found in the Convexs_Invexs_InstallGuide_E.) Three LED’s (red, green, blue) and beeper are included. The Convexs 80F can be flush mounted (indoor / outdoor) in a electrical mounting box. Light (Gray) and Dark (Charcoal) fronts are available. Dimensions: Convexs 80: 80 x 80 x 32 mm, Convexs 80F: 80 x 80 x 27 mm. MOUNTING PROCEDURE CONVEXS For mounting the Convexs the removable backside must be placed on a wall. For removing the backside of the Convexs gently push the two lips at top and bottom towards the middle and remove the backside. After the cable is connected to the front (see ‘Connections’) the front of the Convexs has to be clicked on the backside. MOUNTING PROCEDURE CONVEXS F The Convexs F is opened by using the 2 small holes at the bottom and then lifting the bottom side up. It can be mounted in a electrical mounting box. Take care of the additional foam gasket and mounting direction (drain for releasing eventually collected moisture must be on bottom side). Attention: Don’t mount the Convexs F in a metal environment (Mifare detection and Nedap AM detection can fail). For these applications use the Convexs with the additional Protectors. ® Installation sheet 80 80 Convexs 80 32 Convexs Convexs F 11 16 Ǿ 62.8 Convexs 80F 62.8 Ǿ 3.2 3.4x5.5 60
Download:
Mirror Download [FCC.gov]
Document ID1484512
Application IDAuufHdBkuPV8UFHxUqYT8g==
Document DescriptionUser manual 01
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize23.28kB (290946 bits)
Date Submitted2011-06-16 00:00:00
Date Available2011-06-18 00:00:00
Creation Date2011-04-11 14:36:07
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2011-04-11 14:36:07
Document TitleConvexs 80 series
Document CreatorMicrosoft® Office Word 2007
Document Author: Rene Waenink
FCC ID Filing: CGDCONVEXS

Navigation menu