Netgear orporated 11300172 UTM Security Wireless Module User Manual

Netgear Incorporated UTM Security Wireless Module

a href="https://usermanual.wiki/Netgear-orporated" itemprop="url"> Netgear orporated >

User Man_PY311300172_rev. 1

Installation GuideInstall ModuleTo install the module:Note:  Only one wireless module can be installed. It can be installed in either accessory slot.1.    Turn off power to the UTM9S unit.2.    Remove one of the blank plates on the UTM9s front panel.3.    Save the cover plate for possible later use.4.    Insert the module firmly into the UTM9S.5.    Secure the module using the two panel screws.6.    Restore power to the UTM9S.Remove ModuleTo remove the module:1.    Turn off power to the UTM9S unit.2.    Remove two screws securing the module.3.    Pull the module straight back from the UTM9S.4.   If the module is replaced, follow the Install Module Procedure. If the module is not replaced at this time, install a cover plate over the module slot.5.    Restore power to the UTM9S.ProSecure™ Unified Threat Management UTM9SWLSN ModuleThis guide describes how to install and remove the ProSecure Unified Threat Management UTM9SWLSN Module. Refer to the UTM9S Reference Manual for configuration instructions. You can access the Reference Manual from the UTM9S product management interface, via the Resource CD, or from the NETGEAR support site: http://support.netgear.com. Verify the Package Contents•     ProSecure™ UTM9SWLSN Module •     Installation GuideUTM9SWLSNUTM9SWLSN_IG_28June11.fm  Page 1  Tuesday, June 28, 2011  4:02 PM
June 2011This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive.©2011 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. Technical SupportAfter installing your device, locate the serial number on the label of your product and use it to register your product at http://www.NETGEAR.com/register. Registration is required before you can use the telephone support service. Registration via our web site is strongly recommended.Go to http://support.netgear.com for product updates and Web support. For additional information about setting up, configuring, and using your Product Name Only, see the User Manual. For complete DoC please visit the NETGEAR EU Declarations of Conformity web site at: http://support.netgear.com/app/answers/detail/a_id/11621/ UTM9SWLSN_IG_28June11.fm  Page 2  Tuesday, June 28, 2011  4:02 PM
Federal Communication Commission Interference Statement  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.    These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.   However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. -  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Download:
Mirror Download [FCC.gov]
Document ID1580660
Application IDV5QLvBVc9OMC0B+YS9zvxg==
Document DescriptionUser Man_PY311300172_rev. 1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize25.6kB (320004 bits)
Date Submitted2011-11-14 00:00:00
Date Available2011-11-14 00:00:00
Creation Date2010-06-22 15:19:28
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2011-11-14 16:58:14
Document Titleuntitled
Document CreatorFrameMaker 9.0
FCC ID Filing: PY311300172

Navigation menu