Nextivity orporated CELFI-RSWU104 Cel-Fi Residential System User Manual Basic CMYK

Nextivity Incorporated Cel-Fi Residential System Basic CMYK

Contents

420N001-001-10R51 small

2 Step
Quick Start Guide
The Cel-Fi Window Unit takes the strongest cell signal in your home
and distributes it throughout via the Coverage Unit
Mobile signal
before installation
Mobile signal
after installation
PATENT 7,519,323
Power o
(no green light)
Status red
Status ashing red
Status ashing green
for more than a minute
1. Is the Unit plugged in?
2. Is there power to the outlet?
3. Try exchanging power supplies with the other unit
to see if the power supply is defective.
1. Unplug the unit, wait a few minutes, and try again.
2. Visit the installation support section at:
www.celhelp.com for more information.
1. Do not cover the Unit or block the vents.
2. Move the Unit to a cooler spot.
3. The unit will start operating again when it cools.
1. Wait longer. System is verifying regulatory
compliance. This could take up to 30 minutes.
2. Make sure Units are not next to a Wi-Fi router.
Indicator Problem Try this:
Trouble Shooting Guide
((( )))
((( )))
If there is a system fault, the Coverage Unit will display an error message on the display in the location where
the coverage number is usually displayed (see below).
If this occurs the message will alternate between displaying an “E” (for error) and then a number.
The table below shows what values will be displayed and what they mean.
“E1” Window Unit cannot nd the network Make sure you have one bar coverage on Window Unit.
“E2” Window Unit has interference Make a test call. If you can’t, move the Window Unit.
“E3 or E4” Environment is too warm for Unit System will operate again when it cools.
COVERAGE NUMBER
Common Indicators
Coverage Unit
Window Unit
Error Messages
The Cel-Fi Window and Coverage Units have Power and Status
indicator lights to help you determine how the Units are operating and
how to obtain the best coverage within your home.
Status
Power
Signal
indicators
There is no power
to the Unit.
There is a problem
with Cel-Fi.
The Unit has switched
to a low power mode
because the environ-
ment is too warm.
The Unit is taking
longer than normal to
make a link.
No green bars 1. Try moving the Window Unit to another room
where you have better mobile phone coverage.
(Use your mobile phone to nd the best location.)
1. Move the Coverage Unit closer to
the Window Unit.
1. Move the Coverage Unit farther
away from the Window Unit.
The Coverage Unit is
too far away from the
Window Unit.
The Coverage Unit
is too close to the
Window Unit
420N001-001-10R51
Step1: Setup the Window Unit Step2: Setup the Coverage Unit
Locate the best 3G signal within your
home and plug the Window Unit into
the nearest power outlet. (Look for
the 3G icon on your mobile phone).
Placing the Window Unit near a window is best.
Set Coverage Unit near the middle of your
home and plug it into the nearest outlet.
Wait until the status light stops ashing.
You should see this on the Coverage
Unit indicator panel.
If the indicator looks like this,
move the Coverage Unit
away from the Window Unit.
If the indicator looks like this,
move the Coverage Unit
closer to the Window Unit.
COVERAGE UNIT INDICATOR PANEL
WINDOW UNIT
COVERAGE UNIT
Signal
indicator
Location
indicators
WINDOW
UNIT
FOOT,
WALL MOUNT
AND POWER
ADAPTERS
COVERAGE
UNIT
WINDOW
UNIT
COVERAGE
UNIT
The larger this number,
the better your coverage.
SIGNAL
BAR INDICATOR
Located in the middle
of the Window Unit.
NEED HELP?
Visit www.celhelp.com for an installation video and other helpful
information regarding the installation and trouble shooting of your system
AB C
Note:
If you do not see at least one bar
in the signal indicator window
(as on left), move the unit closer
to a window or try another room.
Upstairs is best if available.
PRESS THE
WINDOW UNIT
ONTO THE FOOT
Status
Power
Status
Power

Navigation menu