Nextivity orporated MBLE Bluetooth LE module User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	2455354
Application ID	ffIKW0OM9xQH8ZslqOf/pw==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.59kB (44933 bits)
Date Submitted	2014-11-25 00:00:00
Date Available	2015-01-31 00:00:00
Creation Date	2014-11-22 15:29:47
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2014-11-22 15:29:47
Document Title	Users Manual 1
Document Creator	Acrobat PDFMaker 11 for Word
Document Author:	CK Li

Regulatory Bluetooth Module Integration Instructions
The Nextivity Bluetooth module will only be implemented internally by Nextivity and is not sold directly, or separately. There is no user manual
for the module. For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation procedure).
 FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: The Federal Communications Commission warns that changes or modifications of the radio module within this device not
expressly approved by Nextivity Inc. could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
V1.1
1 of 2
FCC4_Integration Instructions_Module
The minimum safe distance for people from this module has been determined by conservative calculation to be 20 cm for all allowable
antenna types. The end product User’s Manual must include the following statement in a prominent location: (Note for modules with RF
output power <10mW, this statement is likely not required).
To comply with FCC’s RF radiation exposure requirements, the antenna(s) used for this transmitter must be installed such that a
minimum separation distance of 20 cm is maintained between the radiating element (antenna) & any user’s or bystander at all times
and must not be co-located or operating in conjunction with any other antenna or transmitter.
 Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
 End Product User Manual
The end product user manual shall include all required regulatory information/warning/note as show in this instruction.
Information to the end user regarding how to install or remove this module shall not be provided in the end product user manual.
 End Product Labeling
1) The final end product must be labeled in a visible area with the following:
US FCC:
Contains FCC ID: YETMBLE
Canada IC:
Contains IC: 9298A-MBLE
V1.1
2 of 2
FCC4_Integration Instructions_Module

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : CK Li
Create Date                     : 2014:11:22 15:29:47-08:00
Modify Date                     : 2014:11:22 15:29:47-08:00
Subject                         : 
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2014:11:22 15:29:47-08:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:52dac25f-8e84-4061-8be8-1e14516fd80f
Instance ID                     : uuid:2974955c-6c74-4261-8971-037cca48091c
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : CK Li
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20141122232444
Company                         : 
Comments                        : 
Page Layout                     : OneColumn
Page Count                      : 2

EXIF Metadata provided by EXIF.tools