Nokia Solutions and Networks FXCA-01 FXCA User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	1534882
Application ID	FTnC0FtSXJUUHX/RXmF/NQ==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	340.91kB (4261396 bits)
Date Submitted	2011-09-01 00:00:00
Date Available	2012-04-02 00:00:00
Creation Date	2011-07-08 10:49:58
Producing Software	Corel PDF Engine Version 14.1.0.195
Document Lastmod	2011-07-08 10:50:13
Document Title	Flexi Multiradio BTS GSM EDGE Stack, Wall, Pole Quick Guide.des
Document Author:	©2010 by Nokia Siemens Networks

Flexi Multiradio BTS GSM/EDGE
Stack, Wall, and Pole Quick Guide
This guide can be used as quick reference for Flexi Multiradio BTS GSM/EDGE installation.
Flexi Multiradio BTS GSM/EDGE is a modular base station for GSM/EDGE capacity and coverage.
It can be installed stacked on the floor, or mounted on the wall or on the pole.
This quick guide is for basic stack, wall and pole configurations with 48V DC input power. The
basic installation consists of one System Module (ESMB/C) and one RF Module (Fxxx) allowing
1+1+1 up to 6+6+6 configurations depending on the TRX output power.
For all other installation options, see the user manuals.
Check the delivery
Contents of
1 delivery
Check the site
Clearances
Installation
3 Installing the
plinth
Plinth on the
floor, wall, or pole
Installation
Installation
Installation
Installation
4 Grounding
5 Installing the
6 Installing
7 Grounding
Grounding
principle
Casing
installation
principle
Module
installation
principle
Grounding
principle
the plinth
casings
the modules
modules
Installation
example
Cabling
8 Cabling
Cable routing and cable ties
External power
Internal power cables
Antenna cabling
Optical cables
Transmission and Alarm
cables
Commission BTS
9 Power up and
commissioning
the BTS
Front panel
10 Installing module
front covers
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted in
any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity, or
performance of the mentioned hardware or software products are given “as is” and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS
DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,
DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT
NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS
OPPORTUNITY OR DATA, THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE
INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of
Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners,
and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2010. All rights reserved.
DN70970932, Issue 01 en
Warning
Danger of eye damage from invisible laser radiation produced by the System
Module optical fibre connector!
Always switch off the laser before detaching the optical fibre from the connector.
Caution
Incorrect cables and seals may not provide secured environmental protection. Use
only tested IP65 class cables with seals provided by Nokia Siemens Networks. Store
all unused seals for later use.
Electrostatic discharge (ESD) may damage the modules. Wear an ESD wrist strap or
use a corresponding method when handling the modules.
The rear stopper is fragile. Do not attempt to lift the plinth using the rear stopper.
If water leaks into the outdoor mechanics, the transmission equipment may fail. To help
prevent water leakage, feed the cables through the bottom cable entries in wall and
pole mounting, and through the bottom cable entry holes in stack installation.
Risk of damage to equipment. If modules are exposed to weather conditions, connector
seals or boots must be installed at all times, whether the site is active or not.
1 Contents of delivery
De live ry
Syste m m o du le
C on ten ts o f de live ry
Ve rs io n
Pr od u ct c o de
F lexi Multira dio B TS GSM/ED GE Sys te m Mo d ule
Qua n tity
ES MB
ES MC
4 7 21 0 9
4 7 20 5 9
Ba g R eclo s ab le (15 0 x 2 25 / 2 00 x 2 6 0 ) 0 .1 m m
M1 0 H e x N u t
B1 0 Wa sh e r
AWG Sin g le ca b le term in a l lug rub b er b o ots
M1 0 C a b lete rm (2 5/3 5 m m 2 ) R ing
Pu ll-ou t to ol
T ra n sm iss io n su b -m od u le
F lexi tran s m is sio n inte rfac e E 1
a sym m etrica l su b m o du le (FIE A)
F lexi tran s m is sio n inte rfac e
F lexb us s ub -m o du le (F IF A)
F lexi tran s m is sio n inte rfac e E 1/T 1
s ym m e trica l s ub m o d ule (F IPA)
47 0 24 7 A
47 1 00 7 A
47 0 24 8 A
47 1 60 7 A
PW 1 00 Ba s e-T Eth ern et (R J4 8 ) +
4 xE 1 a s ym m etrica l 75 o hm (SMB) +
o pti on a l op tica l GE (SF P)
47 1 71 9 A
F XD A F le xi Mu ltira d io R F M 9 0 0
F XE A Fle xi Mu ltirad io R FM 18 0 0
F XC A F le xi Mu ltira d io R F M 8 5 0
F XD J Fle xi Mu ltirad io R FM 90 0
F XF A F lexi Multira dio R F M 1 90 0
47 2 08 3 A
47 2 08 4 A
47 2 14 2 A
47 2 14 3 A
47 2 16 6 A
F lexi tran s m is sio n su b -m o du le
(FIQ A)
PW 1 00 Ba s e-T Eth ern et (R J4 8 ) +
4 xE 1/T 1 sym m e trical 1 2 0/ 10 0 oh m
(R J4 8) + op tio na l o ptica l GE (S FP )
F lexi tran s m is sio n su b -m o du le
(FIYA)
Scre w s (p re -in sta lle d)
R F Mod u le
F lexi Multira dio B TS GSM/ED GE R ad io F re q ue n cy
Mo du le
R F Mod u le C a b le Se t
Po w e r ca b le 2 m
Op tical ca b le 2 m
Op tical tra nce ivers
Plin th de livery
Mo du le cas in g
9 9 52 8 1
9 9 48 0 7
47 0 74 5 7
F lexi Mou n ting K it for F loo r, Wa ll, an d Po le
F ixin g p la te fo r th e ca s ing
M5 x 8 scre w s
M5 x 1 2 s crew s
F MF A
F lexi BT S Mo du le ca sin g (3 U )
3 U cab le en trie s
3 U fro n t cover
3 U re a r co ve r
M5 x 1 0 s crew s
M5 x 8 scre w s
EMH A
12
47 0 31 6 A
61 5 02 4 0
61 5 02 7 9
C a ge n uts
Ma inte n an ce s tra p s
Grou n din g cab le
Po le m o un tin g kit
(op tio na l)
F lexi Po le Mo u n ting Kit
Alum iniu m ca s tin gs
Ass e m b ling b o lts
Mo du le fixin g s cre w s
Bo lt res train e r
Check list
Deliveries are complete.
Equipment is not damaged.
F PK A
6 (2 loo s e,
4 p reins ta lled )
47 1 64 9 A
2 Clearances
Minimum clearances
min 80 mm (3.2 in.)
min 30 mm
with no back access
(1.2 in.)
min 80 mm
(2.4 in.)
600 mm
(23.6 in)
min 100 mm
(3.9 in.)
min 75 mm
(3.0 in.)
400 mm
(15.7 in)
recommended
space for hand
tying 150 mm (5.9 in.)
Check list
Note: In a stack, the minimum side clearance
is 75 mm (3 in.). The recommended clearance
for hand tying is 150mm (5.9 in.)
Site meets the minimum clearances.
Plinth on the floor
Facility wall
3 Installing the
plinth
1. Check the clearances around
the plinth.
2. Turn the rear stopper.
360 mm
75 mm
(3.0 in.)
(14.1 in.)
13.5 mm
(0.5 in.)
(4 pcs)
75 mm
(3.0 in.)
Fan maintenance
space
500 mm (19.7 in.)
back stop
Plinth
min 600 mm
(23.6 in.)
3. Place the plinth on the floor,
grounding points facing
forward.
4. Bolt on the floor with 4 bolts,
12 mm (0.47 in.) in diameter.
Tighten to 49.0 Nm (36.1 ft-lb)
300 mm
(11.8 in.)
Plinth on the wall
482,5 mm
185 mm
1. Mark screw locations according to the holes in the plinth and drill holes.
2. Fix the mounting screws on the wall and mount the plinth.
3. Tighten the upper mounting screws.
4. Tighten the lower mounting screws to a torque value of 49 Nm.
Note that the space required between plinths is 100 mm (3.4 inches).

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : ©2010 by Nokia Siemens Networks
Create Date                     : 2011:07:08 10:49:58-05:00
Modify Date                     : 2011:07:08 10:50:13-05:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2011:07:08 10:50:13-05:00
Format                          : application/pdf
Title                           : Flexi Multiradio BTS GSM EDGE Stack, Wall, Pole Quick Guide.des
Creator                         : ©2010 by Nokia Siemens Networks
Document ID                     : uuid:79e716d2-650d-45b2-8852-935a96cc7b45
Instance ID                     : uuid:022ee6d4-5d6e-4e96-9ef3-301e9586b040
Producer                        : Corel PDF Engine Version 14.1.0.195
Page Count                      : 4

EXIF Metadata provided by EXIF.tools