Osram Sylvania IQHOME IQ-H product Zigbee module User Manual

OSRAM SYLVANIA Inc. IQ-H product Zigbee module

Contents

User manual

OSRAM Version1.0nonEDOSProductSpecificationZPR IQZigBeemodulePage1of4Issue: 19.09.2014Status:Comments: ApproversMKTR&DDaiDavidForinformation:  Overview:TheIQZigBeemoduleistobeintegratedintolampstorealizeZigBeefunctions.1. GENERALDESCRIPTION1.1. ProductidentificationIQ‐HproductZigbeemodule1.2. ZigBeeICMarvell88MZ1001.3. InterfacePWM/UART/IIC/SPI;1ADC;TX&RXfortest1.4. Typicalvoltage3.3V1.5. CommunicationprotocolZigBee2012PRO&ZigBeeLightLink1.01.6. OperationTemperature‐40~105℃ 2. ELECTRICALREQUIREMENTS2.1. Nominalvoltagerange2.2~3.6V2.2. NominaloperatingcurrentReceivercurrent(withactiveCPU32MHz):21mATXcurrent(withactiveCPU32MHz):34mA   ‐ 3. MECHANICALREQUIREMENT3.1. TerminalsSolderingPADPINconnector3.2. Size14.7mm*20mm*1.9mm
OSRAM Version1.0nonEDOSProductSpecificationZPR IQZigBeemodulePage2of4Issue: 19.09.2014Status:Comments: ApproversMKTR&DDaiDavidForinformation:  4. CHANGEINDEXVers.DateChange1.015.04.2014Firstdraft1.0.119.09.2014RevisePinassignmentCOMMENTSSectionChange  
OSRAM Version1.0nonEDOSProductSpecificationZPR IQZigBeemodulePage3of4Issue: 19.09.2014Status:Comments: ApproversMKTR&DDaiDavidForinformation:  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: DZO-IQHOME or Contains FCC ID: DZO-IQHOME This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 11099A-IQHOME
OSRAM Version1.0nonEDOSProductSpecificationZPR IQZigBeemodulePage4of4Issue: 19.09.2014Status:Comments: ApproversMKTR&DDaiDavidForinformation:  when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 4.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.

Navigation menu