Ohsung Electronics URCRFX250 REMOTE CONTROL RECEIVER User Manual H

Download:
Mirror Download [FCC.gov]
Document ID	692248
Application ID	Chn2NKag3hYazMz0rixjNA==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.85kB (585673 bits)
Date Submitted	2006-08-10 00:00:00
Date Available	2006-08-10 00:00:00
Creation Date	2006-08-09 16:49:37
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2006-08-10 10:56:04
Document Title	Microsoft Word - H_User manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Jeffrychoi

Test Report No.: GETEC-E3-06-058
FCC Part 15 Subpart B
APPENDIX H
: USER’S MANUAL
EUT Type: Remote Control Receiver
FCC ID.: OZ5URCRFX250
Information To The User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
RFX-250 Installation Manual
Optimizing Narrow Band Reception with
the MRF-300 or MSC-400
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician
for help.
Warning
Changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user's authority to operate the
equipment.
™
COMPLETE
CONTROL
Universal Remote Control
™
®
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
www.universalremote.com
COMPLETE
CONTROL
Universal Remote Control®
RFX-250 INSTALLATION MANUAL
Overview - Compatibility
The RFX-250 is a narrow band RF receiver. It replaces an RFX-150 receiver in either an MRF-300 or MSC-400 system. It is tuned to receive a much
narrower band and is more immune to the interference found near component racks (generated by microprocessors and power supplies). It is
NOT compatible with all URC remote controls.
NOTE: The RFX-250 is ONLY compatible with the current versions of the
MX-3000, MX-950, MX-900 and the TX-1000 remote controls. The RFX250 is NOT compatible with MX-3000 remote controls manufactured
before April 1, 2005.
You can identify the build date of an MX-3000 by looking at the serial
number. The first 6 digits indicate the build date. If the serial number
appears as 122905 014054, the first 6 digits indicate that the remote was
built on December 29, 2005.
Connections
Connect ONE (only)
of either of the RFX250’s RF OUT connectors to ONE (only) of
either of the RF IN
connectors on the
MRF or the MSC.
When the RFX-250 can be placed within 10 feet
of the MRF/MSC unit, you can utilize the cable
with 3.5 mm plugs on both ends. When you
need a longer wire or are connecting up to
three RFX-250’s, use a cable with a minimum of
three conductors. If you use CAT 5, utilize two
conductors each from two of the twisted pairs
for DATA and two from the other twisted pairs
for 5V. Use all four of the other conductors
twisted in with each pair for GND.This provides
better shielding and conductivity for long runs.
RFX-250 INSTALLATION MANUAL
Optimizing Range and Reliability
1. Power on all AV components, dim all dimmers to 50% and power on
anything that may create RF (particularly devices with high speed
microprocessors or hard drives). Observe the RF LED of the RFX-250 by
cupping your hand over it. If it is glowing or flickering you must relocate the RFX-250. If you cannot relocate the RFX-250,
try removing its antenna.
2. Once you have found a location that is absolutely clean
with everything on, test to see if the range is adequate
and that macro reliability is perfect. Start with the
antenna angle set to 45 degrees and positioned so that
the long side of the antenna is facing the customer’s
favorite seating position.
Suggested antenna
angle.
3. When testing, set both the remote and the MRF/MSC to the same
VALID RFID#. Keep in mind that zero (0) is not a valid RFID#. Watch
the STATUS LED on MRF/MSC - it should light every time you press a
button on the remote. This will tell you that the signal was received
and understood. Ignore the RF LED on the RFX-250 (it only indicates
that a signal was received, not that it was understood).
4. If the range is inadequate, you may extend wire to any area that is not
giving good results and place an additional RFX-250 in that area. Up to
three RFX-250’s can be connected to each MRF/MSC.
Once the RFX-250 is correctly connected, the POWER LED lights.
If the RF LED lights, the RFX-250 must
be moved to a new mounting location. It
is receiving in-band RF INTERFERENCE.
NOTE: The RFX-250 is ONLY compatible with additional RFX-250s. You
cannot mix RFX-150s in a system with RFX-250s.
Page 1
Page 2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:f55c74e5-9c78-4794-81f7-286d5378a2f9
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2006:08:10 10:56:04+09:00
Create Date                     : 2006:08:09 16:49:37+09:00
Metadata Date                   : 2006:08:10 10:56:04+09:00
Document ID                     : uuid:84f346c1-2366-4c6c-bb98-fb82417dae4f
Format                          : application/pdf
Title                           : Microsoft Word - H_User manual.doc
Creator                         : Jeffrychoi
Author                          : Jeffrychoi

EXIF Metadata provided by EXIF.tools