Option OMO6712 GTM671W User Manual

Option NV GTM671W

a href="https://usermanual.wiki/Option" itemprop="url"> Option >

User Manual

GTM671WFCC ID: NCMOMO6712IC: 2734A-MO6712Certification LeafletAGENCY REQUIREMENTSLicensed by QUALCOMM Incorporated under one or more of the following United States Patents and/or their counterparts in other nations: 4,901,307; 5,490,165; 5,056,109; 5,504,773; 5,101,501; 5,506,865; 5,109,390; 5,511,073; 5,228,054; 5,535,239; 5,267,261; 5,544,196; 5,267,262; 5,568,483; 5,337,338; 5,600,754; 5,414,796; 5,657,420; 5,416,797; 5,659,569; 5,710,784; 5,778,338Federal communications commission noticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:> Reorient or relocate the receiving antenna.> Increase the separation between the equipment and receiver.> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.> Consult the dealer or an experienced radio or television technician for help.ModificationsThe FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Option could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC rules.This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Exposure Information to Radio Frequency EnergyUsers concerned with the risk of Radio Frequency exposure may wish to limit the duration of their calls and to position the antenna as far away from the body as is practical.Modular approvalThe module can be integrated into fixed or mobile categorized end-products, so that 20 cm separation distance to end-user can be assured. You can integrate the module in a portable device; in this case a permissive change application would be required.Approbation par moduleLe module peut être incorporé à un produit final classé comme fixe ou mobile, mais d’une manière à garantir que l’usager final soit à une distance de 20 cm. Vous pouvez incorporer le module à un appareil portable, et dans ce cas, une demande de changement autorisée serait requise. Device markingThe integrated device must carry the CE mark and Notified body number of the Notified Body used in the Annex IV conformity assessment of the module on the manufacturing label as described in the R&TTE directive 1999/5/EC Annex VII. This Notified Body approval only applies to the module and not the final integrated product. The final integrated product should undergo its own conformity process to the R&TTE directive and should meet all applicable CE marking directives in order to place the CE mark on the final integrated product.The end device must also be appropriatly marked with the FCC identification as described in FCC Part 2.925 and 2.926.Industry Canada requires the host device to be marked with “Contains transmitter module IC: 2734A-MO6712” conform to section 3.2.1 from the RSS-GEN guidelines.Marquage du dispositifLe dispositif incorporé doit porter la marque CE et le numéro de l’organisme notifié utilisé dans l’Annexe IV de l’évaluation de la conformité du module, sur l’étiquette de fabrication, tel que décrit dans l’Annexe VII portant sur les équipements radio et équipements terminaux de télécommunication (« R&TTE »). Cette approbation de l’organisme notifié ne s’applique qu’au module et non au produit final après intégration. Le produit final après intégration devrait être lui-même l’objet d’un processus d’évaluation de la conformité à la directive sur les équipements radio et équipements terminaux de
Download:
Mirror Download [FCC.gov]
Document ID1460097
Application ID6PJr/m0Zwg/zS/Htw9EyiQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize50.51kB (631379 bits)
Date Submitted2011-05-06 00:00:00
Date Available2011-08-02 00:00:00
Creation Date2017-11-05 17:40:20
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-05 17:40:20
Document TitleUser Manual
Document CreatorNitroPDF 6.0
FCC ID Filing: NCMOMO6712

Navigation menu