Paxton Access 337837 Net2 Entry - Panel User Manual

Paxton Access Ltd Net2 Entry - Panel INSTRUCTION Net2 Entry Panel

a href="https://usermanual.wiki/Paxton-Access" itemprop="url"> Paxton Access >

User Manual

Page 107/19/2012Ins-30201-US Net2 Entry - PanelTechnical SupportTechnical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)1.800.672.7298 supportUS@paxton-access.comDocumentation on all Paxton products can be found on our web site - http://www.paxton-access.com/PaxtonThe Net2 Entry panel is a robust door entry panel incorporating both door entry and access control functions. It is powered using power over Ethernet (PoE) and communicates with the other elements of the system using IPv6, providing 'plug and play' installation. Each panel is associated with a Net2 Entry control unit which is the interface to the door hardware. Description of productThe panel is equipped with a keypad and a proximity token reader. Net2 software is used to administer the access control functions. A resident can use either the keypad or a token to gain entry. Installers gain access to the menu options using an engineer code or an engineer token.1. Speaker2. Proximity reader3. Backlit keypad4. LCD display5. IR LEDS for night time operation6. Microphone7. Color camera8. Light sensor24516 783
Page 2Decide how the units are to be connected. You can either run your own wired network or (with the owner's permission) share the buildings existing data network. If using the owners network, the system uses IPv6 protocol and PoE (Power over Ethernet) so the network must support this switch type.InstallationFixing106 mm℄140 mm290 mm320 mm70 mm21 mmThe unit is supplied with the surface mount backbox. A ush mount backbox is also available (PN:337-857). Screws and wall plugs are provided in the tting kit.SURFACE BACKBOXFLUSH BACKBOX51 mm40 mm44 mm205 mm80 mm130 mm281 mm104 mm℄A single hole must be drilled for the single data/power connection. Electrical power is supplied via the data cable (PoE) from the Net2 Entry controller.1. Determine the height for the camera and then mark and drill the cable hole with reference to the Fixing diagram.2. Complete the installation of the mounting backbox - Surface or Flush.3. Connect the Net2 Entry panel to controller.4. Mount the panel in its backbox.5. Power up the panel from controller supply (PoE).The display will ask you to set up an Engineer code. The panel checks to see if any monitors also exist on the network. Any that are detected will now have the engineer code loaded and will store the panel ID that called themThe best height to install the panel is with the camera at eye level This will allow you to see your visitor's face clearly even when they are wearing a hood or cap.To achieve the best camera performance, try to mount the panel facing away from direct sun or a bright light source. This will also help the user to read the LCD display.30 mm196 mm55 mmCamera HeightCable Hole235 mmWhere it is not practical to run a patch cable to the rear of the unit, it can be directly wired to the network cable via the supplied IDC module. Paxton recommend that the network cable is run to each location and terminated in a network box. A patch cable should then be used to link the unit to the network. This makes unit replacement or removal for building maintenance much easier.NOTE: All dimensions are shown in millimetres to maintain accuracy.
Download:
Mirror Download [FCC.gov]
Document ID1749383
Application IDPUzx/jI7UGnpuaR74vyYWg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize91.02kB (1137726 bits)
Date Submitted2012-07-23 00:00:00
Date Available2012-07-23 00:00:00
Creation Date2012-07-19 13:10:16
Producing SoftwareAdobe PDF Library 9.9
Document Lastmod2012-07-19 13:11:19
Document TitleINSTRUCTION - Net2 Entry - Panel
Document CreatorAdobe InDesign CS5 (7.0.4)
FCC ID Filing: USE337837

Navigation menu