Altivar_71_ATV71HC31N4

: Pdf 104183-Attachment 104183-Attachment 785901 Batch8 unilog

Open the PDF directly: View PDF .
Page Count: 4

Download
Open PDF In Browser	View PDF

Product data sheet
Characteristics

ATV71HC31N4

variable speed drive ATV71 - 315KW 500HP 480V - EMC filter

Range of product

Altivar 71

Product or component
type

Variable speed drive

Product specific application

Complex, high-power machines

Assembly style

With heat sink

Component name

ATV71

Variant

Reinforced version

EMC filter

Integrated

Network number of
phases

3 phases

[Us] rated supply voltage

380...480 V - 15...10 %

Motor power kW

315 kW 3 phases 380...480 V

Motor power hp

500 hp 3 phases 380...480 V

Line current

444 A 480 V 3 phases 315 kW 500 hp
555 A 380 V 3 phases 315 kW 500 hp

Apparent power

365,3 kVA 380 V 3 phases 315 kW 500 hp

Prospective line Isc

≤ 50 kA 3 phases

Nominal output current

616 A 2.5 kHz 380 V 3 phases 315 kW 500 hp
616 A 2.5 kHz 460 V 3 phases 315 kW 500 hp

Maximum transient current

924 A 60 s 3 phases 315 kW 500 hp
1016 A 2 s 3 phases 315 kW 500 hp

Speed drive output frequency

0...500 Hz

Nominal switching frequency

2.5 kHz

Switching frequency

2.5...8 kHz adjustable
2.5...8 kHz with derating factor

Asynchronous motor
control profile

ENA (Energy adaptation) system for unbalanced
loads
Flux vector control (FVC) with sensor (current vector)
Sensorless flux vector control (SFVC) (voltage or
current vector)
Voltage/Frequency ratio (2 or 5 points)

Type of polarization

No impedance Modbus

Complementary
Product destination

Asynchronous motors
Synchronous motors

Supply voltage limits

323...528 V

Supply frequency

50...60 Hz - 5...5 %

Network frequency limits

47,5...63 Hz

Speed range

1...100 asynchronous motor in open-loop mode, without speed feedback
1...1000 asynchronous motor in closed-loop mode with encoder feedback
1...50 synchronous motor in open-loop mode, without speed feedback

Speed accuracy

+/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn
to Tn
+/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn

Torque accuracy

+/- 15 % in open-loop mode, without speed feedback
+/- 5 % in closed-loop mode with encoder feedback

Transient overtorque

170 % +/- 10 % 60 s
220 % +/- 10 % 2 s

Jun 20, 2014

1

The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.

Main

Braking torque

30 % without braking resistor
< 150 % with braking or hoist resistor

Synchronous motor control profile

Vector control without speed feedback

Regulation loop

Adjustable PI regulator

Motor slip compensation

Adjustable
Automatic whatever the load
Not available in voltage/frequency ratio (2 or 5 points)
Suppressable

Local signalling

1 LED red drive voltage

Output voltage

<= power supply voltage

Insulation

Electrical between power and control

Type of cable

IEC cable without mounting kit 1 45 °C copper 70 °C PVC
IEC cable with an IP21 or an IP31 kit 3 40 °C copper 70 °C PVC
IEC cable without mounting kit 1 45 °C copper 90 °C XLPE/EPR
UL 508 cable with a NEMA Type1 kit 3 40 °C copper 75 °C PVC

Electrical connection

Terminal 2.5 mm² AWG 14 AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B,
LI1...LI6, PWR
Terminal 4 x 185 mm² L1/R, L2/S, L3/T, U/T1, V/T2, W/T3
Terminal 8 x 185 mm² PC/-, PA/+

Tightening torque

0,6 N.m AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR
41 N.m 360 lb.in L1/R, L2/S, L3/T, U/T1, V/T2, W/T3
41 N.m 360 lb.in PC/-, PA/+

Supply

Internal supply 24 V DC 21...27 V ≤ 200 mA overload and short-circuit protection
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % ≤
10 mA overload and short-circuit protection

Analogue input number

2

Analogue input type

Bipolar differential voltage AI1-/Al1+ +/- 10 V DC 24 V max 11 bits + sign
Software-configurable current AI2 0...20 mA 242 Ohm 11 bits
Software-configurable voltage AI2 0...10 V DC 24 V max 30000 Ohm 11 bits

Sampling duration

2 ms +/- 0.5 ms LI1...LI5 discrete
2 ms +/- 0.5 ms LI6 if configured as logic input discrete
2 ms +/- 0.5 ms AI1-/Al1+ analog
2 ms +/- 0.5 ms Al2 analog

Response time

2 ms +/- 0.5 ms AO1 analog
7 ms +/- 0.5 ms R1A, R1B, R1C discrete
7 ms +/- 0.5 ms R2A, R2B discrete
<= 100 ms in STO (Safe Torque Off)

Accuracy

+/- 0.6 % AI1-/Al1+ for a temperature variation 60 °C
+/- 0.6 % AI2 for a temperature variation 60 °C
+/- 1 % AO1 for a temperature variation 60 °C

Linearity error

+/- 0.15 % of maximum value AI1-/Al1+, AI2
+/- 0.2 % AO1

Analogue output number

1

Analogue output type

Software-configurable current AO1 0...20 mA 500 Ohm 10 bits
Software-configurable logic output AO1 10 V ≤ 20 mA
Software-configurable voltage AO1 0...10 V DC 470 Ohm 10 bits

Discrete output number

2

Discrete output type

Configurable relay logic R1A, R1B, R1C NO/NC 100000 cycles
Configurable relay logic R2A, R2B NO 100000 cycles

Minimum switching current

3 mA 24 V DC configurable relay logic

Maximum switching current

2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms R1, R2
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms R1, R2
5 A 250 V AC resistive cos phi = 1 L/R = 0 ms R1, R2
5 A 30 V DC resistive cos phi = 1 L/R = 0 ms R1, R2

Discrete input number

7

Discrete input type

Programmable LI1...LI5 24 V DC level 1 PLC 3500 Ohm
Safety input PWR 24 V DC 1500 Ohm
Switch-configurable LI6 24 V DC level 1 PLC 3500 Ohm
Switch-configurable PTC probe LI6 0...6 1500 Ohm

Discrete input logic

Negative logic (sink) LI6 if configured as logic input > 16 V < 10 V
Negative logic (sink) LI1...LI5 > 16 V < 10 V
Positive logic (source) LI6 if configured as logic input < 5 V > 11 V
Positive logic (source) LI1...LI5 < 5 V > 11 V
PWR < 2 V > 17 V

Acceleration and deceleration ramps

S, U or customized
Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Linear adjustable separately from 0.01 to 9000 s

Braking to standstill

By DC injection

2

Protection type

Against exceeding limit speed drive
Against input phase loss drive
Break on the control circuit drive
Input phase breaks drive
Line supply overvoltage drive
Line supply undervoltage drive
Motor phase break motor
Overcurrent between output phases and earth drive
Overheating protection drive
Overvoltages on the DC bus drive
Power removal motor
Short-circuit between motor phases drive
Thermal protection drive
Thermal protection motor

Insulation resistance

> 1 MOhm 500 V DC for 1 minute to earth

Frequency resolution

0.024/50 Hz analog input
0.1 Hz display unit

Communication port protocol

CANopen
Modbus

Type of connector

1 RJ45 Modbus on front face
1 RJ45 Modbus on terminal
Male SUB-D 9 on RJ45 CANopen

Physical interface

2-wire RS 485 Modbus

Transmission frame

RTU Modbus

Transmission rate

20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen
4800 bps, 9600 bps, 19200 bps, 38.4 Kbps Modbus on terminal
9600 bps, 19200 bps Modbus on front face

Data format

8 bits, 1 stop, even parity Modbus on front face
8 bits, odd even or no configurable parity Modbus on terminal

Number of addresses

1...127 CANopen
1...247 Modbus

Method of access

Slave CANopen

Marking

CE

Operating position

Vertical +/- 10 degree

Product weight

215 kg

Option card

I/O extension card
Communication card Modbus TCP
Communication card Fipio
Communication card Modbus/Uni-Telway
Communication card Modbus Plus
Communication card Ethernet/IP
Communication card DeviceNet
Communication card Profibus DP
Communication card Profibus DP V1
Communication card Interbus-S
Communication card CC-Link
Controller inside programmable card
Interface card for encoder
Overhead crane card

3

Environment
Noise level

77 dB 86/188/EEC

Dielectric strength

3535 V DC between earth and power terminals
5092 V DC between control and power terminals

Electromagnetic compatibility

1.2/50 μs - 8/20 μs surge immunity test level 3 IEC 61000-4-5
Conducted radio-frequency immunity test level 3 IEC 61000-4-6
Electrical fast transient/burst immunity test level 4 IEC 61000-4-4
Electrostatic discharge immunity test level 3 IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 IEC
61000-4-3
Voltage dips and interruptions immunity test IEC 61000-4-11

Standards

EN/IEC 61800-3
EN/IEC 61800-5-1
EN 55011 class A group 2
EN 61800-3 environments 1 category C3
EN 61800-3 environments 2 category C3
IEC 60721-3-3 class 3C2
UL Type 1

Product certifications

C-Tick
CSA
GOST
NOM 117
UL

Pollution degree

2 EN/IEC 61800-5-1
3 UL 840

IP degree of protection

IP00 EN/IEC 60529
IP00 EN/IEC 61800-5-1
IP30 on side parts EN/IEC 61800-5-1
IP30 on the front panel EN/IEC 60529
IP30 on the front panel EN/IEC 61800-5-1
IP30 on side parts EN/IEC 60529
IP41 on upper part EN/IEC 61800-5-1
IP41 on upper part EN/IEC 60529
IP54 on lower part EN/IEC 61800-5-1
IP54 on lower part EN/IEC 60529

Vibration resistance

0.6 gn 10...200 Hz EN/IEC 60068-2-6
1.5 mm peak to peak 3...10 Hz EN/IEC 60068-2-6

Shock resistance

4 gn 11 ms EN/IEC 60068-2-27

Relative humidity

5...95 % without condensation IEC 60068-2-3
5...95 % without dripping water IEC 60068-2-3

Ambient air temperature for operation

-10...50 °C without derating

Ambient air temperature for storage

-25...70 °C

Operating altitude

1000...3000 m with current derating 1 % per 100 m
≤ 1000 m without derating

RoHS EUR conformity date

3Q2009

RoHS EUR status

Will be compliant

4



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
Page Count                      : 4
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Title                           : Altivar_71_ATV71HC31N4.pdf
Creator                         : Catalogue Retriever Servlet
Date                            : 2014:06:20 18:10:47-0-4:00
PDF Version                     : 1.4
Producer                        : Catalogue Retriever Servlet
Create Date                     : 2014:06:20 18:10:47-0-4:00
Creator Tool                    : Catalogue Retriever Servlet
Author                          : Catalogue Retriever Servlet

EXIF Metadata provided by EXIF.tools