TB04400001E

April 2009

CA08102001E For more information visit:

www.eaton.com

Contents

Distribution & Control Transformers and Power Supplies

44-1

44

Distribution & Control Trans-

formers and Power Supplies

Description Page

Distribution Transformers

Single-Phase Encapsulated and Ventilated, 60 Hz. . . . . . . . . . . . . . . . . . .

44-2

Electrostatically Shielded Transformers. . . . . . . . . . . . . . . . . . . . . . . . . . .

44-8

Open Type Core and Coil Assembly Transformers . . . . . . . . . . . . . . . . . .

44-13

Buck-Boost and Low Voltage Lighting Transformers . . . . . . . . . . . . . . . .

44-15

Control Transformers

Type MTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-32

Type MTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-37

Type MTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-39

Type MTK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-48

CE Marked. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-53

Type AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-61

Product Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-63

Power Supplies

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-65

PSG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-65

PSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-71

ELC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-77

EZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-79

Sensor Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

44-81

Control Transformers PSG Power Supplies

April 2009

44-2

For more information visit:

www.eaton.com

CA08102001E

Distribution & Control Transformers and Power Supplies

44

General Purpose Transformers

Single-Phase Encapsulated (Type EP), Ventilated (Type DS-3), 60 Hz

Single-Phase Encapsulated

(Type EP), Ventilated (Type

DS-3), 60 Hz

Type EP 3-25 kVA

Product Description

Type EP

■

Sand and Resin Encapsulated design.

■

Suitable for indoor or outdoor

applications.

■

Totally enclosed, non-ventilated

enclosures.

■

Enclosures are NEMA



3R rated.

■

Mountable in any position indoors

and upright only outdoors.

■

185ºC insulation system.

■

115ºC rise standard; 80°C optional.

■

Available in ratings through 37.5 kVA

and 4160 volts primary.

Type DS-3

■

Ventilated, NEMA 2 enclosure

standard.

■

Suitable for indoor applications,

outdoors when weathershields are

also installed.

■

Upright mounting only.

■

220ºC insulation system.

■

150ºC rise standard; 115°C or 80°C

optional.

■

Available in single-phase ratings

15 – 167 kVA and up to 4160 volts

primary.

Application Description

The basic purpose of a transformer

is voltage transformation as near as

practically possible to the load for

economy and distribution of power.

Typical loads for dry-type distribution

transformers include lighting, heating,

air conditioners, fans and machine

tools. Such loads are found in com-

mercial, institutional, industrial

and residential structures.

Features, Beneﬁts

and Functions

■

UL



listed.

■

60 Hz operation.

■

Short-term overload capability

as required by ANSI.

■

Meet NEMA ST-20 sound levels.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer



dry-type distribu-

tion and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI and IEEE Standards. All 600 volt

class transformers are UL listed unless

otherwise noted.

Seismically Qualiﬁed

Cutler-Hammer manufactured dry-type

distribution transformers are seismi-

cally qualiﬁed, and exceed require-

ments of the Uniform Building Code



(UBC), International Building Code

(IBC), and California Code Title 24.

Product Speciﬁcations

Frequency

Cutler-Hammer standard dry-type

distribution transformers are designed

for 60 Hertz operation. Transformers

required for other frequencies are

available and must be speciﬁcally

designed.

Overload Capability

Short-term overload is designed into

transformers as required by ANSI.

Dry-type distribution transformers

will deliver 200% nameplate load for

one-half hour; 150% load for one hour;

and 125% load for four hours without

being damaged provided that a con-

stant 50% load precedes and follows

the overload. See ANSI C57.96-01.250

for additional limitations.

Continuous overload capacity is not

deliberately designed into a trans-

former because the design objective is

to be within the allowed winding tem-

perature rise with nameplate loading.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-1. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Enclosures

Cutler-Hammer ventilated transform-

ers, Type DS-3, utilize a NEMA 2 rated

(drip-proof) enclosure as standard,

and are rated NEMA 3R with the addi-

tion of weathershields. Cutler-Hammer

encapsulated transformers, Type EP,

utilize a NEMA 3R rated enclosure

as standard.

Sound Levels

All Cutler-Hammer 600 volt class

general purpose dry-type distribution

transformers are designed to meet

NEMA ST-20 sound levels listed here.

These are the sound levels measured

in a soundproof environment. Actual

sound levels measured at an installa-

tion will likely be higher due to electri-

cal connections and environmental

conditions. Lower sound levels are

available and should be speciﬁed

when the transformer is going to

be installed in an area where sound

may be a concern.

Table 44-2. Average Sound Levels



Currently being reviewed and revised by

NEMA.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

NEMA ST-20 Average Sound Level in dB

kVA Up to 1.2 kV Above 1.2 kV

Ventilated Encap-

sulated

Ventilated

0 – 9

10 – 50

51 – 150

151 – 300

40

45

50

55

45

50

55

57

45

50

55

58

301 – 500

501 – 700

701 – 1000

1001 – 1500

60

62

64

65

59

61

63

64

60

62

64

65

April 2009

CA08102001E For more information visit:

www.eaton.com

44-3

Distribution & Control Transformers and Power Supplies

44

General Purpose Transformers

Single-Phase Encapsulated (Type EP), Ventilated (Type DS-3), 60 Hz

Winding Terminations

Primary and secondary windings are

terminated in the wiring compartment.

Encapsulated units have copper leads

or stabs brought out for connections.

Ventilated transformers have leads

brought out to aluminum pads that

are pre-drilled to accept Cu/Al lugs.

Lugs are not supplied with these

transformers.

Eaton recommends

external cables be rated 90°C (sized

at 75°C ampacity) for encapsulated

designs and 75°C for ventilated

designs.

Series-Multiple Windings

Series-multiple windings consist of

two similar coils in each winding

which can be connected in series or

parallel (multiple). Transformers with

series-multiple windings are desig-

nated with an “X” or “/” between the

voltage ratings, such as voltages of

“120/240” or “240 X 480.” If the series-

multiple winding is designated by an

“X,” the winding can be connected

only for a series or parallel. With the

“/” designation, a mid-point also

becomes available in addition to the

series or parallel connection. As an

example, a 120 X 240 winding can be

connected for either 120 (parallel) or

240 (series), but a 120/240 winding can

be connected for 120 (parallel), or 240

(series), or 240 with a 120 mid-point.

The following pages provide listings for most

standard transformer ratings and styles.

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton.

April 2009

44-4

For more information visit:

www.eaton.com

CA08102001E

Distribution & Control Transformers and Power Supplies

44

General Purpose Transformers

Single-Phase Encapsulated (Type EP), Ventilated (Type DS-3), 60 Hz

Product Selection

Additional Product Selection information begins on

Page 44-63

.

Type EP 3-37.5 kVA Type DS-3 15-167 kVA

Table 44-3. Single-Phase Selection Information — Types EP, DS-3, 60 Hz



Contact Eaton for availability of 0.05 – 0.25 kVA designs.



1@+5%, 2@-5% at 240 volts primary; 2@+2.5%, 4@-2.5% at 480 volts primary.

Note:

Contact your local Eaton sales ofﬁce for CE Mark transformer requirements.

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . .

DT-1

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

120 x 240 Volts to 120/240 Volts



.5

1

1.5

—

EP

115

6-1/2

8-5/8

10-3/4

4-5/8

5-3/4

6-3/16

4-15/16

5-3/4

6-5/8

16

31

42

165

219

273

117

146

157

125

146

166

7

14

19

FR57

FR59A

FR67

3E

Indoor-

Outdoor

S10N11S51N

S10N11S01N

S10N11S16N

2

3

5

—

EP

115

10-3/4

14-1/8

16

6-3/16

7-3/4

10-3/8

6-5/8

8

9-7/8

42

55

113

273

359

406

157

197

263

166

203

251

19

25

51

FR68

FR176

FR177

3E

Indoor-

Outdoor

S10N11S02N

S10N11S03N

S10N11S05N

7.5

10

15

25

—

EP

115

16

19

22-3/8

10-3/8

13-3/8

16-3/8

9-7/8

10-1/2

13-3/8

14-1/2

123

193

216

375

406

482

568

263

339

416

251

266

368

56

88

98

170

FR178

FR179

FR180

FR182

3E

Indoor-

Outdoor

S10N11S07N

S10N11S10N

S10N11S15N

S10N11S25N

37.5

50



DS-3

150

37-5/8

22-5/8

19-1/2

306

340

953

956

574

495

139

154

FR817

FR818

3XD

WS11

T10P11S37

T10P11S50

208 Volts to 120/240 Volts



.5

1

1.5

—

EP

115

6-1/2

8-5/8

10-3/4

4-5/8

5-3/4

6-3/16

4-15/16

5-3/4

6-5/8

16

31

42

165

219

273

117

146

157

125

146

166

7

14

19

FR57

FR59A

FR67

26A

Indoor-

Outdoor

S29N11S51N

S29N11S01N

S29N11S16N

2

3

5

—

EP

115

10-3/4

14-1/8

16

6-3/16

7-3/4

10-3/8

6-5/8

8

9-7/8

42

65

113

273

359

406

157

197

263

166

203

251

19

30

51

FR68

FR176

FR177

26A

Indoor-

Outdoor

S29N11S02N

S29N11S03N

S29N11S05N

7.5

10

15

25

—

EP

115

16

19

22-3/8

10-3/8

13-3/8

16-3/8

9-7/8

10-1/2

13-3/8

14-1/2

123

193

216

395

406

482

568

263

339

416

251

266

359

56

88

98

179

FR178

FR179

FR180

FR182

26A

Indoor-

Outdoor

S29N11S07N

S29N11S10N

S29N11S15N

S29N11S25N

25

37.5

50

2@+2.5%

4@-2.5%

DS-3

150

31-1/4

37-5/8

22-5/8

17-1/2

19-1/2

212

306

340

793

953

956

574

445

495

96

139

154

FR816

FR817

FR818

260A

WS11

T29M11S25

T29M11S37

T29M11S50

75

100

2@+2.5%

1@+5%

4@-2.5%

2@-5%

DS-3

150

42-1/8

24

23-3/8

510

600

1070

610

594

232

272

FR819

FR820

260A

551A

WS16

T29M11S75

T29R11S99

277 Volts to 120/240 Volts



.5

1

1.5

—

EP

115

8-5/8

10-3/4

5-3/4

6-3/16

5-3/4

6-5/8

26

31

42

165

219

273

146

157

146

166

12

14

19

FR58A

FR59A

FR67

524A

Indoor-

Outdoor

S27N11S51A

S27N11S01A

S27N11S16A

2

3

5

—

EP

115

10-3/4

14-1/8

16

7-3/4

10-3/8

8

9-7/8

65

55

113

359

406

197

263

203

251

30

25

51

FR176

FR177

524A

Indoor-

Outdoor

S27N11S02A

S27N11S03N

S27N11S05N

7.5

10

15

25

—

EP

115

16

19

22-3/8

10-3/8

13-3/8

16-3/8

9-7/8

10-1/2

13-3/8

14-1/2

123

193

180

375

406

482

568

263

339

416

251

266

359

56

88

82

170

FR178

FR179

FR180

FR182

524A

Indoor-

Outdoor

S27N11S07N

S27N11S10N

S27N11S15N

S27N11S25N

25

37.5

50

2@+2.5%

4@-2.5%

DS-3

150

31-1/4

37-5/8

22-5/8

17-1/2

19-1/2

212

306

340

793

953

956

574

445

495

96

139

154

FR816

FR817

FR818

262C

WS11

T27M11S25

T27M11S37

T27M11S50

75

100

2@+2.5%

4@-2.5%

DS-3

150

42-1/8

24

23-3/8

510

600

1070

610

594

232

272

FR819

FR820

262C

WS16

T27M11S75

T27M11S99

April 2009

CA08102001E For more information visit:

www.eaton.com

44-5

Distribution & Control Transformers and Power Supplies

44

General Purpose Transformers

Single-Phase Encapsulated (Type EP), Ventilated (Type DS-3), 60 Hz

Table 44-4. Single-Phase Selection Information — Types EP, DS-3, 60 Hz



1@+10% FCBN at 240 volts; 2@+5% FCBN at 480 volts.



2@+5% FCBN at 240 volts; 4@+2.5% FCBN at 480 volts.



1@+5%, 2@-5% at 240 volts primary; 2@+2.5%, 4@-2.5% at 480 volts primary.



Floor-mount only.



480 volts primary to 120/240 volts secondary.

Note:

Contact your local Eaton sales ofﬁce for CE Mark transformer requirements.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield

Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

240 x 480 Volts to 120/240 Volts

.050

.075

.100

—

EP

115

6-1/2

3-7/8

7

165

98

3

FR52

FR54

3A

Indoor-

Outdoor

S20N11S81N

S20N11S85N

S20N11S82N

.150

.25

.5

—

EP

115

6-1/2

3-7/8

4-5/8

3-7/8

4-1/8

4-15/16

8

12

16

165

98

117

98

103

125

4

5

7

FR55

FR56

FR57

3A

Indoor-

Outdoor

S20N11S83N

S20N11S26N

S20N11S51N

.75

1

1.5

—

EP

115

8-5/8

10-3/4

5-3/4

6-3/16

5-3/4

6-5/8

26

31

42

219

273

146

157

146

166

12

14

19

FR58A

FR59A

FR67

3A

Indoor-

Outdoor

S20N11S76N

S20N11S01N

S20N11S16N

2

3

—



—



EP

115

10-3/4

14-1/8

6-3/16

7-3/4

6-5/8

8

42

65

273

359

157

197

166

203

19

30

FR68

FR176

3A

9A

Indoor-

Outdoor

S20N11S02N

S20N11S03N

S20K11S03N

5

7.5

—



—



—

EP

115

16

10-3/8

9-7/8

113

105

406

263

251

51

48

FR177

FR178

3A

9A

3A

Indoor-

Outdoor

S20N11S05N

S20K11S05N

S20N11S07N

7.5

10



—



—



EP

115

16

19

10-3/8

13-3/8

9-7/8

10-1/2

123

193

406

482

263

339

251

266

56

88

FR178

FR179

9A

3A

9A

Indoor-

Outdoor

S20K11S07N

S20N11S10N

S20K11S10N

15

25

—



—



—

EP

115

19

22-3/8

13-3/8

16-3/8

13-3/8

14-1/2

216

385

482

568

339

416

266

368

98

175

FR180

FR182

3A

23A

3A

Indoor-

Outdoor

S20N11S15N

S20L11S15N

S20N11S25N

25

37.5



EP

115

22-3/8

28-1/4

16-3/8

22-5/8

14-1/2

14-5/8

375

735

568

717

416

570

368

371

170

334

FR182

FR300A

23A

248A

Indoor-

Outdoor

S20L11S25N

S20L11S37



15

25

37.5



DS-3

150

30-1/4

31-1/4

37-5/8

16-7/8

22-5/8

15-7/8

17-1/2

19-1/2

147

212

306

768

793

953

428

574

402

445

495

67

96

139

FR815

FR816

FR817

3XA

WS15

WS11

T20P11S15

T20P11S25

T20P11S37

50

75

100

167



2@+2.5%



4@-2.5%

DS-3

150

37-5/8

42-1/8

62-7/8

22-5/8

24

30

19-1/2

23-3/8

34

340

510

600

1200

956

1070

1597

574

610

762

495

594

863

154

232

272

545

FR818

FR819

FR820

FR814

3XA

288A

WS11

WS16

WS13

T20P11S50

T20P11S75

T20P11S99

T48M11S67D



For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton.

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . .

DT-1

April 2009

44-6

For more information visit:

www.eaton.com

CA08102001E

Distribution & Control Transformers and Power Supplies

44

General Purpose Transformers

Single-Phase Encapsulated (Type EP), Ventilated (Type DS-3), 60 Hz

Table 44-5. Single-Phase Selection Information — Types EP, DS-3, 60 Hz

NEMA 3R, 316 stainless steel enclosure.

Refer to your local Eaton sales ofﬁce

Note: Contact your local Eaton sales ofﬁce

for CE Mark transformer requirements.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

190/200/208/220 x 380/400/416/440 Volts to 110/220 Volts 50/60 Hz — Export Model IP 22 Rated

.5

1

1.5

2

—

EP

115

10-3/4

14-1/8

6-3/16

7-3/4

6-5/8

8

42

65

273

359

157

197

166

203

19

30

FR67

FR176

538A

Indoor-

Outdoor

S40N14S51CE

S40N14S01CE

S40N14S16CE

S40N14S02CE

3

5

7.5

—

EP

115

16

19

10-3/8

13-3/8

9-7/8

10-1/2

113

140

193

406

482

263

339

251

266

51

64

88

FR177

FR178

FR179

538A

Indoor-

Outdoor

S40N14S03CE

S40N14S05CE

S40N14S07CE

10

15

—

EP

115

19

22-3/8

13-3/8

16-3/8

13-3/8

14-1/2

216

375

482

433

339

415

266

359

98

170

FR180

FR182

538A

Indoor-

Outdoor

S40N14S10CE

S40N14S15CE

120/208/240/277 Volts to 120/240 Volts 60 Hz

1

1.5

2

—

EP

115

10-3/4

14-1/8

6-3/16

7-3/4

6-5/8

8

42

65

273

359

157

197

166

203

19

30

FR67

FR176



Indoor-

Outdoor

S54N11S01

S54N11S16

S54N11S02

3

5

7.5

10

—

EP

115

16

19

10-3/8

13-3/8

9-7/8

10-1/2

13-3/8

113

140

193

216

406

482

263

339

251

266

51

64

88

98

FR177

FR178

FR179

FR180



Indoor-

Outdoor

S54N11S03

S54N11S05

S54N11S07

S54N11S10

240 x 480 Volts to 120/240 Volts Stainless Steel 

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

65

113

123

359

406

197

263

203

251

30

51

56

FR176

FR177

FR178

3A

Indoor-

Outdoor

S20N11S03SS

S20N11S05SS

S20N11S07SS

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

193

205

375

482

566

339

416

266

359

88

93

170

FR179

FR180

FR182

3A

Indoor-

Outdoor

S20N11S10SS

S20N11S15SS

S20N11S25SS

480 Volts to 120/240 Volts

1

1.5

2

—

2@-5%

EP

115

8-5/8

10-3/4

5-3/4

6-3/16

5-3/4

6-5/8

31

42

219

273

146

157

146

166

14

19

FR59A

FR67

FR68

2D

Indoor-

Outdoor

S48G11S01N

S48G11S16N

S48G11S02N

3

5

—

2@+2.5%

—

2@-5%

2@+2.5%

2@-5%

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

65

113

359

406

197

263

203

251

30

51

FR176

FR177

2D

16A

2D

Indoor-

Outdoor

S48G11S03N

S48D11S03N

S48G11S05N

5

7.5

2@+2.5%

—

2@+2.5%

2@-5%

2@+2.5%

EP

115

16

10-3/8

9-7/8

113

123

406

263

251

51

56

FR177

FR178

16A

2D

16A

Indoor-

Outdoor

S48D11S05N

S48G11S07N

S48D11S07N

10

15

—

2@+2.5%

—

2@-5%

2@+2.5%

2@-5%

EP

115

19

13-3/8

10-1/2

13-3/8

193

216

482

339

266

88

98

FR179

FR180

2D

16A

2D

Indoor-

Outdoor

S48G11S10N

S48D11S10N

S48G11S15N

15

25

2@+2.5%

—

2@+2.5%

2@-5%

4@-2.5%

EP

115

19

22-3/8

20-3/4

13-3/8

16-3/8

19-1/8

13-3/8

14-1/2

13-5/8

216

385

410

482

568

525

339

416

483

266

359

349

98

175

186

FR180

FR182

FR132

16A

2D

83A

Indoor-

Outdoor

S48D11S15N

S48G11S25N

S48M11S25N

480 Volts to 120/240 Volts Stainless Steel, Copper Windings 

10

15

25

2@+2.5%

4@-2.5%

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

210

235

415

482

525

339

483

266

349

95

107

188

FR179

FR180

FR182

16A

83A

Indoor-

Outdoor

S48D11S10SSCU

S48D11S15SSCU

S48M11S25SSCU

600 Volts to 120/240 Volts

.5

.75

1

—

2@-5%

EP

115

6-1/2

8-5/8

4-5/8

5-3/4

4-15/16

5-3/4

16

26

31

165

219

117

146

125

146

7

12

14

FR57

FR58A

FR59A

2I

Indoor-

Outdoor

S60G11S51N

S60G11S76N

S60G11S01N

1.5

2

3

—

2@-5%

EP

115

10-3/4

14-1/8

6-3/16

7-3/4

6-5/8

8

42

65

273

359

157

197

166

203

19

30

FR67

FR68

FR176

2I

Indoor-

Outdoor

S60G11S16N

S60G11S02N

S60G11S03N

5

7.5

10

—

2@-5%

EP

115

16

19

10-3/8

13-3/8

9-7/8

10-1/2

105

123

193

406

482

263

339

251

266

48

56

88

FR177

FR178

FR179

2I

Indoor-

Outdoor

S60G11S05N

S60G11S07N

S60G11S10N

15

25

—

2 @ 2.5%

4@-2.5%

EP

115

19

22-3/8

20-3/4

13-3/8

16-3/8

19-1/8

13-3/8

14-1/2

13-5/8

216

385

395

482

568

525

339

416

483

266

359

349

98

175

180

FR180

FR182

FR132

527A

83B

Indoor-

Outdoor

S60J11S15N

S60J11S25N

S60M11S25N

25

37.5

50

2@+2.5%

4@-2.5%

DS-3

150

31-1/4

37-5/8

22-5/8

17-1/2

19-1/2

212

306

340

793

953

956

574

445

495

96

139

154

FR816

FR817

FR818

276B

262B

WS11

T60M11S25

T60M11S37

T60M11S50D

75

100

167

2@+2.5%

4@-2.5%

DS-3

150

42-1/8

62-7/8

24

30

23-3/8

34

510

600

1200

1070

1597

610

762

594

863

232

272

545

FR819

FR820

FR814

262B

288B

WS16

WS13

T60M11S75

T60M11S99

T60M11S67A

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-7

Distribution & Control Transformers and Power Supplies

44

General Purpose Transformers

Single-Phase Encapsulated (Type EP), Ventilated (Type DS-3), 60 Hz

Table 44-6. Single-Phase Selection Information — Types EP, DS-3, 60 Hz

No UL label.

Refer to your Eaton sales ofﬁce.

NEMA 3R enclosure and/or UL label available at additional cost. Specify at time of order entry if required.

Not seismic qualiﬁed. Available by special order.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

2400 Volts to 120/240 Volts

1.5 — — EP 115 10-3/4 6-3/16 6-5/8 42 273 157 166 19 FR68 18A —S42N11S16N 

3

5

10

15

25

—

4@-2.5%

EP

115

16

19

22-3/8

26-3/8

10-3/8

13-3/8

16-3/8

9-7/8

10-1/2

14-1/2

14-1/8

113

123

216

375

405

406

482

566

668

263

339

416

251

266

359

51

56

98

170

184

FR177

FR178

FR179

FR182

FR190

12A

—

S42J11S03N 

S42J11S05N 

S42J11S10N 

S42J11S15N 

S42J11S25N 

37.5

50

75

100

2@+2.5%

2@-2.5%

DS-3

150

28

30

36

22

24

27

20

26

300

420

500

570

684

732

879

537

586

659

488

635

137

191

228

260



—

T42D11S37 

T42D11S50 

T42D11S75 

T42D11S99 

2400 Volts to 240/480 Volts

37.5

50

2@+2.5%

2@-2.5%

DS-3

150

28

30

22

24

20

26

300

420

684

732

537

586

488

635

137

191



—

T42D21S37 

T42D21S50 

4160 Volts to 120/240 Volts

1.5 — — EP 115 10-3/4 6-3/16 6-5/8 42 273 157 166 19 FR68 524G —S46N11S16N 

3

5

10

15

—

4@-2.5%

EP

115

16

19

22-3/8

10-3/8

13-3/8

16-3/8

9-7/8

10-1/2

14-1/2

113

123

193

375

406

482

566

263

339

416

251

266

359

51

56

88

170

FR177

FR178

FR179

FR182

12B

—

S46J11S03N 

S46J11S05N 

S46J11S10A 

S46J11S15A 

25

37.5

50

2@+2.5%

2@-2.5%

DS-3

150

28

30

22

24

20

26

280

300

420

984

684

732

537

586

488

635

128

137

191



—

T46D11S25 

T46D11S37 

T46D11S50 

75

100

167

2@+2.5%

2@-2.5%

DS-3

150

30

36

50

24

27

33

26

35

500

570

1000

732

879

1220

586

659

806

635

854

228

260

455



—

T46D11S75 

T46D11S99 

T46D11S67 

4160 Volts to 240/480 Volts

37.5

50

75

100

2@+2.5%

2@-2.5%

DS-3

150

28

30

36

22

24

27

20

26

300

420

500

570

684

732

879

537

586

659

488

635

137

191

228

260



—

T46D21S37 

T46D21S50 

T46D21S75 

T46D21S99 

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-8

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Electrostatically Shielded Transformers

Single- and Three-Phase Types EP, DS-3, EPT, DT-3, 60 Hz

Single- and Three-Phase,

Types EP, DS-3, EPT, DT-3, 60 Hz

Type DT-3

Product Description

Types EP, EPT

■Sand and Resin Encapsulated design.

■Suitable for indoor or outdoor

applications.

■Totally enclosed, non-ventilated

enclosures.

■Enclosures are NEMA 3R rated.

■Mountable in any position indoors

and upright only outdoors.

■185ºC insulation system.

■115ºC rise standard; 80°C rise

optional.

■Available in single-phase ratings

through 37.5 kVA and 4160 volts

primary (EP).

■Available in three-phase ratings

through 75 kVA and 4160 volts

primary (EPT).

Types DS-3, DT-3

■Ventilated, NEMA 2 enclosure

standard.

■Suitable for indoor applications,

outdoors when weathershields are

also installed.

■Upright mounting only.

■220ºC insulation system.

■150ºC rise standard; 115°C or 80°C

optional.

■Available in single-phase ratings

15 – 167 kVA and up to 4160 volts

primary (DS-3).

■Available in three-phase ratings

15 – 1500 kVA and up to 4160 volts

primary (DT-3).

Application Description

Electrostatically shielded transformers

are used to protect sensitive electrical

equipment from undesirable high fre-

quency signals commonly generated

by lighting, switching surges, motors,

and SCRs feeding noise back into the

line. An electrostatic shield, consisting

of a single turn of aluminum foil placed

between the primary and secondary

winding, is used to provide from

30 to 70 dB attenuation of wide band

line-to-ground (common mode) noise.

Typical uses of shielded isolation

transformers include:

■Suppression of transients and noise

which travels from its source to the

sensitive load equipment.

■Suppression of noise and transients

at the point where the noise or

transients are originating, thus

preventing them from backfeeding

from the source to the feeders.

■Transform one voltage level to

another.

■Isolate one circuit from another.

Features, Beneﬁts

and Functions

■UL listed.

■60 Hz operation standard,

50/60 Hz operation available.

■Short-term overload capability

as required by ANSI.

■Meet NEMA ST-20 sound levels.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribution

and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI and IEEE Standards. All 600 volt

class transformers are UL listed unless

otherwise noted.

Seismically Qualiﬁed

Cutler-Hammer manufactured dry-type

distribution transformers are seismi-

cally qualiﬁed, and exceed require-

ments of the Uniform Building Code

(UBC), International Building Code (IBC)

and California Code Title 24.

Product Speciﬁcations

Frequency

Cutler-Hammer standard dry-type dis-

tribution transformers are designed

for 60 Hertz operation. Transformers

required for other frequencies are

available and must be speciﬁcally

designed.

Overload Capability

Short-term overload is designed into

transformers as required by ANSI.

Dry-type distribution transformers

will deliver 200% nameplate load for

one-half hour; 150% load for one hour;

and 125% load for four hours without

being damaged provided that a con-

stant 50% load precedes and follows

the overload. See ANSI C57.96-01.250

for additional limitations.

Continuous overload capacity is not

deliberately designed into a trans-

former because the design objective is

to be within the allowed winding tem-

perature rise with nameplate loading.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-7. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Enclosures

Cutler-Hammer ventilated

transformers, Types DS-3 and DT-3

utilize a NEMA 2 rated (drip-proof)

enclosure as standard, and are rated

NEMA 3R with the addition of

weathershields. Cutler-Hammer

encapsulated transformers, Types

EP and EPT, utilize a NEMA 3R rated

enclosure as standard.

The following pages provide listings for most

standard transformer ratings and styles.

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

April 2009

CA08102001E For more information visit: www.eaton.com

44-9

Distribution & Control Transformers and Power Supplies

44

Electrostatically Shielded Transformers

Single- and Three-Phase, Types EP, 60 Hz

Sound Levels

All Eaton’s Cutler-Hammer 600 volt

class general purpose dry-type distri-

bution transformers are designed to

meet NEMA ST-20 sound levels listed

here. These are the sound levels mea-

sured in a soundproof environment.

Actual sound levels measured at an

installation will likely be higher due to

electrical connections and environ-

mental conditions. Lower sound levels

are available and should be speciﬁed

when the transformer is going to

be installed in an area where sound

may be a concern.

Table 44-8. Average Sound Levels 

Currently being reviewed and revised by

NEMA.

Winding Terminations

Primary and secondary windings are

terminated in the wiring compartment.

Encapsulated units have copper leads or

stabs brought out for connections. Venti-

lated transformers have leads brought

out to aluminum pads that are pre-drilled

to accept Cu/Al lugs. Lugs are not sup-

plied with these transformers. Eaton rec-

ommends external cables be rated 90°C

(sized at 75°C ampacity) for encapsulated

designs and 75°C for ventilated designs.

Series-Multiple Windings

Series-multiple windings consist of

2 similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X 240

winding can be connected for either

120 (parallel) or 240 (series), but a

120/240 winding can be connected

for 120 (parallel), or 240 (series), or

240 with a 120 mid-point.

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-9. Single-Phase Selection Information — Types EP, 60 Hz

Note: Contact your local Eaton sales ofﬁce

for CE Mark transformer requirements.

NEMA ST-20 Average Sound Level in dB

kVA Up to 1.2 kV Above 1.2 kV

Ventilated Encap-

sulated

Ventilated

0 – 9

10 – 50

51 – 150

151 – 300

40

45

50

55

45

50

55

57

45

50

55

58

301 – 500

501 – 700

701 – 1000

1001 – 1500

60

62

64

65

59

61

63

64

60

62

64

65

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

120 x 240 Volts to 120/240 Volts

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

50

90

123

359

406

197

263

203

251

23

41

56

FR176

FR177

FR178

90B

Indoor-

Outdoor

S10N11E03N

S10N11E05N

S10N11E07N

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

210

205

375

482

568

339

416

266

359

95

93

170

FR179

FR180

FR182

90B

Indoor-

Outdoor

S10N11E10N

S10N11E15N

S10N11E25N

120 Volts to 120 Volts

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

60

100

123

359

406

197

263

203

251

27

45

56

FR176

FR177

FR178

77A

Indoor-

Outdoor

S12N12E03N

S12N12E05N

S12N12E07N

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

180

216

375

482

568

339

416

266

359

82

98

170

FR179

FR180

FR182

77A

Indoor-

Outdoor

S12N12E10N

S12N12E15N

S12N12E25N

208 Volts to 120/240 Volts

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

60

135

95

359

406

197

263

203

251

27

61

43

FR176

FR177

FR178

578A

Indoor-

Outdoor

S29N11E03N

S29N11E05N

S29N11E07N

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

165

185

375

482

568

339

416

266

359

75

94

170

FR179

FR180

FR182

578A

Indoor-

Outdoor

S29N11E10N

S29N11E15N

S29N11E25N

208 Volts to 208 Volts

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

65

113

123

359

406

197

263

203

251

30

51

56

FR176

FR177

FR178

77B

Indoor-

Outdoor

S29N29E03N

S29N29E05N

S29N29E07N

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

195

216

375

482

568

339

416

266

359

89

98

170

FR179

FR180

FR182

77B

Indoor-

Outdoor

S29N29E10N

S29N29E15N

S29N29E25N

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-10

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Electrostatically Shielded Transformers

Single-Phase, Types EP, DS-3, 60 Hz

Table 44-10. Single-Phase Selection Information — Types EP, DS-3, 60 Hz

2@+5% FCBN at 240 volts; 4@-2.5% FCBN at 480 volts.

1@+5%, 2@-5% at 240 volts primary; 2@+2.5%, 4@-2.5% at 480 volts primary.

Do not meet Federal Energy Efﬁciency standards that are effective January 1, 2007. Cannot be purchased for use in the United States or territories.

Note: Contact your local Eaton sales ofﬁce for CE Mark transformer requirements.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

240 Volts to 240 Volts

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

65

113

123

359

406

197

263

203

251

30

51

56

FR176

FR177

FR178

77C

Indoor-

Outdoor

S24N24E03N

S24N24E05N

S24N24E07N

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

193

216

375

482

568

339

416

266

359

88

98

170

FR179

FR180

FR182

77C

Indoor-

Outdoor

S24N24E10N

S24N24E15N

S24N24E25N

277 Volts to 120/240 Volts

3

5

7.5

—

EP

115

14-1/8

16

7-3/4

10-3/8

8

9-7/8

65

113

75

359

406

197

263

203

251

30

51

34

FR176

FR177

FR178

513B

Indoor-

Outdoor

S27N11E03N

S27N11E05N

S27N11E07N

10

15

25

—

EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

162

216

375

482

568

339

416

266

359

74

98

170

FR179

FR180

FR182

513B

Indoor-

Outdoor

S27N11E10N

S27N11E15N

S27N11E25N

240 x 480 Volts to 120/240 Volts

.25

.50

.75

—

EP

115

6-1/2

8-5/8

4-5/8

5-3/4

4-1/8

4-15/16

5-3/4

12

16

26

165

219

117

146

103

125

146

5

7

12

FR56

FR57

FR58A

90A

Indoor-

Outdoor

S20N11E26A

S20N11E51A

S20N11E76A

1

1.5

2

—

EP

115

8-5/8

10-3/4

5-3/4

6-3/16

5-3/4

6-5/8

31

42

219

273

146

157

146

166

14

19

FR59A

FR67

FR68

90A

Indoor-

Outdoor

S20N11E01A

S20N11E16A

S20N11E02A

3

5

7.5

—

EP

115

14-1/8

16

7-11/16

10-3/8

8

9-7/8

65

113

123

359

406

195

263

203

251

30

51

56

FR176

FR177

FR178

90A

Indoor-

Outdoor

S20N11E03A

S20N11E05A

S20N11E07A

10

15

25

—



—



EP

115

19

22-3/8

13-3/8

16-3/8

10-1/2

13-3/8

14-1/2

166

216

375

482

568

339

416

266

359

75

98

170

FR179

FR180

FR182

90A

526A

Indoor-

Outdoor

S20N11E10A

S20N11E15A

S20L11E25A

15

25

37.5



DS-3

150

30-1/4

31-1/4

37-5/8

16-7/8

22-5/8

15-7/8

17-1/2

19-1/2

147

212

306

768

793

953

428

574

402

445

495

67

96

139

FR815

FR816

FR817

261A

WS15

WS11

T20P11E15 

T20P11E25 

T20P11E37 

50

75

100



DS-3

150

37-5/8

42-1/8

22-5/8

24

19-1/2

23-3/8

340

510

600

953

1070

574

610

495

594

154

232

272

FR818

FR819

FR820

261A

WS11

WS16

T20P11E50 

T20P11E75 

T20P11E99 

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-11

Distribution & Control Transformers and Power Supplies

44

Electrostatically Shielded Transformers

Three-Phase, Types EPT, DT-3, 60 Hz

Table 44-11. Three-Phase Selection Information — Types EPT, DT-3, 60 Hz

T-T connected secondary.

Do not meet Federal Energy Efﬁciency standards that are effective January 1, 2007. Cannot be purchased for use in the United States or territories.

Refer to your Eaton sales ofﬁce.

Not seismic qualiﬁed. Available by special order.

Note: Contact your local Eaton sales ofﬁce for CE Mark transformer requirements.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

208 ∆ Volts to 208Y/120 Volts

15

30

2@+2.5%

2@-2.5%

4@-2.5%

EPT

DT-3

115

150

17-3/8

25

30

20

20-1/8

10-9/16

14-1/8

275

152

230

441

635

762

508

511

267

359

125

69

104

FR95

FR909

FR910A

86A

283A

Indoor-

Outdoor

WS31

Y29D28E15B 

V29M28E15A 

V29M28E30B 

45

75

112.5

2@+2.5%

1@+5%

4@-2.5%

2@-5%

DT-3

150

30

39-1/4

20-1/8

26-1/8

14-3/8

19-1/8

310

480

600

762

995

511

663

364

486

485

140

218

272

FR912A

FR914B

FR915B

283A

325A

WS31

WS33

V29M28E45B 

V29M28E75B 

V29R28E12B 

150

225

300

1@+5%

2@-5%

DT-3

150

46-5/8

62-1/4

28

31-1/4

23

30-1/4

870

1600

1183

1581

710

794

584

768

395

728

FR916A

FR918A

325A

287A

WS19

WS34

V29R28E49B 

V29R28E22B 

V29R28E33B 

480 ∆ Volts to 208Y/120 Volts

3

6

9

15

2@+2.5%

2@-2.5%

EPT

115

13-3/8

15-7/8

17-3/8

15-15/16

16-1/2

20

8-5/16

9-7/8

10-9/16

116

165

190

275

340

403

441

405

419

508

211

251

267

52

75

86

125

FR201

FR200

FR103

FR95

86B

Indoor-

Outdoor

Y48D28E03A 

Y48D28E06A 

Y48D28E09N 

Y48D28E15B 

15

30

45

2@+2.5%

4@-2.5%

DT-3

150

25

30

20-1/8

14-1/8

14-3/8

152

230

325

635

762

511

359

364

69

104

148

FR909

FR910A

FR912A

283B

WS31

V48M28E15B 

V48M28E30B 

V48M28E45 

75

112.5

150

2@+2.5%

4@-2.5%

DT-3

150

39-1/4

46-5/8

26-1/8

28

19-1/8

23

515

870

995

1183

663

710

486

584

234

395

FR914B

FR916A

283B

WS33

WS19

V48M28E75 

V48M28E12 

V48M28E49 

225

300

500

2@+2.5%

4@-2.5%

DT-3

150

56-1/4

57-1/2

75

31-1/4

36-1/4

44-1/2

24-1/4

32-1/4

36

1200

1710

2500

1427

1460

1905

790

921

1130

616

817

914

545

776

1135

FR917

FR923

FR919

292A

WS34

WS37

WS35

V48M28E22 

V48M28E33 

V48M28E55G 

750

1000

2@+2.5%

1@+3.5%

4@-2.5%

1@-3.5%

DT-3

150

75



44-1/2



36



2900



1905



1130



914



1315



FR920



292A



WS35



V48M28E77B 

V48W28E11A 

480 ∆ Volts to 208Y/120 Volts — Copper Windings

15

30

45

2@+2.5%

4@-2.5%

DT-3

150

25

30

20-1/8

14-1/8

14-3/8

172

300

370

635

762

511

359

364

78

136

168

FR909

FR910A

FR912A

283B

WS31

V48M28E15CU 

V48M28E30CU 

V48M28E45CU 

75

112.5

150

2@+2.5%

4@-2.5%

DT-3

150

39-1/4

46-5/8

26-1/8

28

19-1/8

23

600

675

900

995

1183

663

710

485

584

272

306

409

FR915B

FR916A

283B

WS33

WS19

V48M28E75CU 

V48M28E12CU 

V48M28E49CU 

225

300

500

2@+2.5%

4@-2.5%

DT-3

150

56-1/4

62-1/4

75

31-1/4

44-1/2

24-1/4

30-1/4

36

1200

2150

3100

1427

1581

1905

790

794

1130

616

768

914

545

977

1407

FR917

FR918A

FR919

283B

292A

WS34

WS35

V48M28E22CU 

V48M28E33CU 

V48M28E55CU 

480 ∆ Volts to 480Y/277 Volts

9

15

2@+2.5%

2@-2.5%

EPT

115

15-7/8

17-3/8

16-1/2

20

9-7/8

10-9/16

190

275

403

441

419

508

251

267

86

125

FR103

FR95

86C

Indoor-

Outdoor

Y48D47E09N 

Y48D47E15B 

30

45

75

2@+2.5%

4@-2.5%

DT-3

150

30

39-1/4

20-1/8

26-1/8

14-1/8

14-3/8

19-1/8

230

310

480

762

995

511

663

359

364

486

104

140

218

FR910A

FR912A

FR914B

283B

WS31

WS33

V48M47E30B 

V48M47E45B 

V48M47E75B 

112.5

150

225

2@+2.5%

4@-2.5%

DT-3

150

39-1/4

46-5/8

56-1/4

26-1/8

28

31-1/4

19-1/8

23

24-1/4

600

950

1100

995

1183

1427

663

710

790

485

584

616

272

431

499

FR915B

FR916A

FR917

283B

WS33

WS19

WS34

V48M47E12B 

V48M47E49B 

V48M47E22B 

300

500

750

2@+2.5%

4@-2.5%

DT-3

150

62-1/4

75

31-1/4

44-1/2

30-1/4

36

1600

2400

2900

1581

1905

794

1130

768

914

728

1088

1315

FR918A

FR919

FR920

283B

292A

WS34

WS35

V48M47E33B 

V48M47E55G 

V48M47E77A 

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-12

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Electrostatically Shielded Transformers

Three-Phase, Types EPT, DT-3, 60 Hz

Table 44-12. Three-Phase Selection Information — Types EPT, DT-3, 60 Hz

T-T connected secondary.

Center Tap capacity limited to 5% of rated kVA.

Do not meet Federal Energy Efﬁciency standards that are effective January 1, 2007. Cannot be purchased for use in the United States or territories.

Note: Contact your local Eaton sales ofﬁce for CE Mark transformer requirements.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Weathershield Style

Number

Price

U.S. $

FCAN FCBN H W D H W D Catalog

Number

Price

U.S. $

480 ∆ Volts to 240 ∆ Volts

3

6

9

15

—

2@-5%

4@-2.5%

EPT

115

13-3/8

15-7/8

17-3/8

15-15/16

16-1/2

20

8-5/16

9-7/8

10-9/16

116

165

195

275

340

403

441

405

419

508

211

251

267

52

75

89

125

FR201

FR200

FR103

FR95

88A

505B

Indoor-

Outdoor

Y48G24E03A 

Y48G24E06A 

Y48J24E09A 

Y48J24E15A 

480 ∆ Volts to 240 ∆ Volts With 120 Volt Lighting Tap on B Phase 

15

30

45

2@+2.5%

4@-2.5%

DT-3

150

25

30

20-1/8

14-1/8

14-3/8

152

230

310

635

762

511

359

364

69

104

140

FR909

FR910A

FR912A

284B

WS31

V48M22E15B 

V48M22E30A 

V48M22E45A 

75

112.5

150

2@+2.5%

4@-2.5%

DT-3

150

39-1/4

46-5/8

26-1/8

28

19-1/8

23

480

600

785

995

1183

663

710

486

485

584

218

272

356

FR914B

FR915B

FR916A

284B

WS33

WS19

V48M22E75A 

V48M22E12A 

V48M22E49A 

225

300

500

2@+2.5%

4@-2.5%

DT-3

150

56-1/4

62-1/4

75

31-1/4

44-1/2

24-1/4

30-1/4

36

1100

1600

2400

1427

1581

1905

790

794

1130

616

768

914

499

728

1088

FR917

FR918A

FR919

284B

293A

WS34

WS35

V48M22E22A 

V48M22E33A 

V48M22E55A 

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-13

Distribution & Control Transformers and Power Supplies

44

Open Type Core and Coil Assembly Transformers

Single- and Three-Phase

Single- and Three-Phase,

Types DS-3C, DT-3C, 60 Hz

Product Description

■220°C insulation system, 150°C

rise standard; 115°C or 80°C

optional.

■Aluminum windings

(copper optional).

Application Description

The basic purpose of a transformer

is voltage transformation as near as

practically possible to the load for

economy and distribution of power.

Typical loads for dry-type distribution

transformers include lighting, heating,

air conditioners, fans, and machine

tools. Such loads are found in

commercial, institutional, industrial,

and residential structures.

Open core and coil assemblies are

typically used by panel builders and

equipment OEM customers who

incorporate the entire transformer

into their structures. A versatile option

to purchasing a standard, enclosed

transformer and discarding the

unneeded enclosure parts.

Features, Beneﬁts

and Functions

■ (UL recognized).

■60 Hz operation standard,

50/60 Hz operation available.

■Short-term overload capability as

required by ANSI.

■Meet NEMA ST-20 sound levels.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribu-

tion and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI, and IEEE Standards.

Seismically Qualiﬁed

All Cutler-Hammer manufactured

dry-type distribution transformers

are seismically qualiﬁed, and exceed

requirements of the Uniform Building

Code (UBC), International Building

Code and California Code Title 24.

Product Speciﬁcations

Frequency

Cutler-Hammer standard dry-type distri-

bution transformers are designed for 60

Hz operation. Transformers required for

other frequencies are available and

must be speciﬁcally designed.

Overload Capability

Short-term overload is designed into

transformers as required by ANSI.

Dry-type distribution transformers

will deliver 200% nameplate load for

one-half hour; 150% load for one-hour;

and 125% load for four-hours without

being damaged provided that a con-

stant 50% load precedes and follows

the overload. See ANSI C57.96-01.250

for additional limitations.

Continuous overload capacity is not

deliberately designed into a trans-

former because the design objective is

to be within the allowed winding tem-

perature rise with nameplate loading.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-13. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Sound Levels

All Cutler-Hammer 600 volt class general

purpose dry-type distribution transform-

ers are designed to meet NEMA ST-20

sound levels listed here. These are the

sound levels measured in a soundproof

environment. Actual sound levels mea-

sured at an installation will likely be higher

due to electrical connections and environ-

mental conditions. Lower sound levels are

available and should be speciﬁed when

the transformer is going to be installed in

an area where sound may be a concern.

Table 44-14. Average Sound Levels 

Currently being reviewed and revised by

NEMA.

Winding Terminations

Lugs are not supplied with these trans-

formers. Eaton recommends external

cables be rated 90°C (sized at 75°C

ampacity) for encapsulated designs

and 75°C for ventilated designs.

Series-Multiple Windings

Series-multiple windings consist of 2

similar coils in each winding which can

be connected in series or parallel (multi-

ple). Transformers with series-multiple

windings are designated with an “X” or

“/” between the voltage ratings, such as

voltages of “120/240” or “240 X 480.” If

the series-multiple winding is desig-

nated by an “X,” the winding can be

connected only for a series or parallel.

With the “/” designation, a mid-point

also becomes available in addition to

the series or parallel connection. As an

example, a 120 X 240 winding can be

connected for either 120 (parallel) or 240

(series), but a 120/240 winding can be

connected for 120 (parallel), or 240

(series), or 240 with a 120 mid-point.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

The following pages provide listings for most

standard transformer ratings and styles.

For other ratings or styles not shown, refer

to Eaton.

NEMA ST-20 Average Sound Level in dB

kVA Up to 1.2 kV Above 1.2 kV

Ventilated Encap-

sulated

Ventilated

0 – 9

10 – 50

51 – 150

151 – 300

40

45

50

55

45

50

55

57

45

50

55

58

301 – 500

501 – 700

701 – 1000

1001 – 1500

60

62

64

65

59

61

63

64

60

62

64

65

April 2009

44-14

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Open Type Core and Coil Assembly Transformers

Single- and Three-Phase

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-15. Single-Phase Selection Information — Type DS-3C, 60 Hz

1@+5%, 2@–5% at 240 volts primary; 2@+2.5%, 4@–2.5% at 480 volts primary.

Table 44-16. Three-Phase Selection Information — Type DT-3C, 60 Hz

Note: Contact your local Eaton sale ofﬁces for availability of additional Open Type Core and Coil Assemblies.

Note: Contact your local Eaton sales ofﬁce for CE Mark transformer requirements.

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Style

Number

Price

U.S. $

FCAN FCBN H W D H W D

240 x 480 Volts to 120/240 Volts

15

25

37.5

50



DS-3C

150

30-1/4

31-1/4

37-5/8

16-7/8

22-5/8

15-7/8

17-1/2

19-1/2

147

212

306

340

768

793

953

428

574

402

445

495

67

96

139

154

FR815C

FR816C

FR817C

FR818C

3XA

T20P11S15ZZ

T20P11S25ZZ

T20P11S37ZZ

T20P11S50ZZ

kVA Full Cap. Taps Type °C

Temp.

Rise

Dimensions (Inches) Wt.

Lbs.

Dimensions (mm) Wt.

kg

Frame Wiring

Diagram

Number

Style

Number

Price

U.S. $

FCAN FCBN H W D H W D

480 ∆ Volts to 208Y/120 Volts

15

30

45

2@+2.5%

4@-2.5%

DT-3C

150

20-5/16

23-13/16

24-3/4

20-1/8

14

128

195

250

516

605

629

511

356

58

89

114

FR909C

FR910C

FR912C

280B

V48M28T15ZZ

V48M28T30ZZ

V48M28T45ZZ

75

112.5

150

2@+2.5%

4@-2.5%

DT-3C

150

29-3/8

31-3/8

41-7/16

25-5/16

19

20

395

530

656

746

797

1052

643

483

508

180

241

298

FR914AC

FR915C

FR916C

280B

V48M28T75ZZ

V48M28T12ZZ

V48M28T49ZZ

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-15

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single- and Three-Phase

Applications, 60 Hz

Type EP

Product Description

Types EP, EPT

■Sand and Resin Encapsulated design.

■Suitable for indoor or outdoor

applications.

■Totally enclosed, non-ventilated

enclosures.

■Enclosures are NEMA 3R rated.

■Mountable in any position indoors

and upright only outdoors.

■185ºC insulation system.

■115ºC rise standard; 80°C rise

optional.

■Available in single-phase ratings

through 7.5 kVA.

Application Description

A buck-boost transformer is used

to provide an economical method of

correcting a lower or higher voltage

rating more suitable for efﬁcient oper-

ation of electrical equipment. Type EP

Buck-Boost transformers are small

kVA, single-phase transformers with

dual primary and dual secondary

windings and are usually connected as

autotransformers by utilizing one unit

for single-phase applications and

either two or three units banked for

three-phase operation. They are pri-

marily used for motor operation and

should not be used for motor control

circuits, to correct ﬂuctuating line

voltage or to obtain a neutral on a

delta system. Buck-boost transformers

are ideally suited for use with low

voltage lighting systems, such as

outdoor lighting.

Features, Beneﬁts

and Functions

■UL listed.

■60 Hz operation.

■600 volt class insulation.

■Short-term overload capability

as required by ANSI.

■Meet NEMA ST-20 sound levels.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribution

and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI and IEEE Standards. All 600 volt

class transformers are UL listed unless

otherwise noted.

Seismically Qualiﬁed

Cutler-Hammer manufactured dry-type

distribution transformers are seismi-

cally qualiﬁed, and exceed require-

ments of the Uniform Building Code

(UBC), International Building Code (IBC)

and California Code Title 24.

Product Speciﬁcations

Frequency

Cutler-Hammer buck-boost transform-

ers are designed for 60 Hz operation.

Overload Capability

Short-term overload is designed into

transformers as required by ANSI.

Dry-type distribution transformers

will deliver 200% nameplate load for

one-half hour; 150% load for one-hour;

and 125% load for four-hours without

being damaged provided that a con-

stant 50% load precedes and follows

the overload. See ANSI C57.96-01.250

for additional limitations.

Continuous overload capacity is not

deliberately designed into a trans-

former because the design objective is

to be within the allowed winding tem-

perature rise with nameplate loading.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-17. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Enclosures

Cutler-Hammer encapsulated buck-

boost transformers utilize a NEMA 3R

rated enclosure.

Sound Levels

All Cutler-Hammer 600 volt class gen-

eral purpose dry-type distribution

transformers are designed to meet

NEMA ST-20 sound levels listed here.

These are the sound levels measured

in a soundproof environment. Actual

sound levels measured at an installa-

tion will likely be higher due to electri-

cal connections and environmental

conditions. Lower sound levels are

available and should be speciﬁed

when the transformer is going to be

installed in an area where sound may

be a concern.

Table 44-18. Average Sound Levels 

Currently being reviewed and revised by

NEMA.

Winding Terminations

Primary and secondary windings are

terminated in the wiring compartment.

Encapsulated units have copper leads

or stabs brought out for connections.

Lugs are not supplied with these

transformers. Eaton recommends

external cables be rated 90°C (sized

at 75°C ampacity) for encapsulated

designs.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

NEMA ST-20 Average Sound Level in dB

kVA Up to 1.2 kV

Encapsulated

0 – 9

10 – 50

51 – 150

151 – 300

45

50

55

57

301 – 500

501 – 700

701 – 1000

1001 – 1500

59

61

63

64

April 2009

44-16

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single- and Three-Phase

Series-Multiple Windings

Series-multiple windings consist of 2

similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series),

or 240 with a 120 mid-point.

Note: When installation is to be made on a

grounded system, consideration must be

given to the resulting voltage. Thus, on a

208 grounded wye/120 system the voltage

can be boosted to 240 volts but the voltage

to ground will be 139 volts. If 240/120 volts

with a mid-point ground is needed, a stan-

dard two-winding transformer must be used.

The following formulas can be used to

calculate speciﬁc requirements.

For Single-Phase:

For Three-Phase:

Product Selection

For quick selection data, refer to the

tables on the following pages.

Selection Requirements

You should have the following

information before selecting a

buck-boost transformer.

Line Voltage

The voltage that you want to buck

(decrease) or boost (increase). This

can be found by measuring the supply

line voltage with a voltmeter.

Load Voltage

The voltage at which your equipment

is designed to operate. This is listed on

the nameplate of the load equipment.

Load Amperes or Load kVA

You do not need to know both — one

or the other is sufﬁcient for selection

purposes. This information usually can

be found on the nameplate of the

equipment that you want to operate.

Frequency

The supply line frequency must be the

same as the frequency of the equip-

ment to be operated — Eaton’s Cutler-

Hammer Buck-Boost Transformers

operate at 60 Hz only.

Phase

The supply line should be the same as

the equipment to be operated — either

single or three-phase.

Transformer Interconnection

For three-phase applications, intercon-

nections of transformers should be

made in a junction box. Two or three

transformers may be used depending

on an open delta (2) or wye (3)

connection.

5-Step Selector

The tables which follow will simplify

the selection of the buck-boost trans-

formers. There are no calculations

needed; simply follow these 5 steps.

1. Refer to the table having the same

output voltage as the equipment

you want to operate. For example,

if you are installing a 240 volt 6 kVA

single-phase load use Selection

Table 44-23.

2. Select the available line voltage

across the top of the chart which

is closest to the actual supply volt-

age. Therefore, for example, if the

available line voltage is 213 volts,

use the 212 volt column.

3. Read down the column until you

reach an output kVA or amps rat-

ing equal to or greater than the

load requirements. Since 6 kVA, in

the example, is not listed, use the

next higher rating or 7.5 kVA.

4. Read across to the far left columns

for the catalog number and quan-

tity of transformers for your appli-

cation. In this case, you will need

one (1) catalog number

S10N06A01N.

5. Connect the buck-boost trans-

former(s) you have selected in

accordance with the connection

diagram speciﬁed at the bottom of

the available line voltage column.

In this example, Diagram “F”

would be used.

Note: For 1-phase connections and 3-phase

open delta connections, inputs and outputs

may be reversed. kVA capacity remains

constant.

Additional Product Selection

information begins on Page 44-63.

LOAD kVA

Load Voltage x

Full Line Amperes

1000

---------------------------------------------=

LOAD kVA

Line Load Voltage x 1.73 x

Full Load Amperes

1000

------------------------------------------------------------------=

April 2009

CA08102001E For more information visit: www.eaton.com

44-17

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single- and Three-Phase

Wiring Diagrams

Figure 44-1. Buck-Boost Transformers Wiring Diagrams

WARNING! If input is 3-wire, “neutral” connection must be isolated and insulated! When used to supply a 3-phase, 4-wire load, the source must be

3-phase, 4-wire wye.

H4

H

3

H2

H4

H

3

N

eut

r

al

H4

H

3

H1

H2

Hi

g

hV

o

lta

ge

L

o

w

V

olta

ge

X2

X4

X2

X4

X2

X4

X1

X

3

X1

X

3

X1

X

3

L

o

w

V

olta

ge

N

eut

r

al

Hi

g

h

V

olta

ge

X

3

X4

X1

X2

X

3

X4

X1

X2

X

3

X4

X1

X2

H

3

H1

H

3

H1

H

3

H1

H2

H4

H2

H4

X1

H4

H

3

H1

H2

H4

H

3

H1

H2

N

eut

r

al

H

3

H1

H2

X

3

X1

X

3

X1

X

3

Low

V

olta

ge

Hi

g

h

V

olta

ge

X2

X4

X2

X4

X2

X4

L

o

w

V

olta

ge

N

eut

r

al

Hi

g

h

V

olta

ge

X

3

X4

X1

X2

H4

H

3

H1

H2

X

3

X4

X1

X2

H4

H

3

H1

H2

X

3

X4

X1

X2

H4

H

3

H1

H2

X1

N

eut

r

al

X2

X

3

X4

X1

X2

X

3

X1

X2

X

3

X4

L

o

w

V

olta

ge

Hi

g

h

V

olta

ge

H

3

H2

H1

H4

H

3

H2

H1

H4

H

3

H2

H1

H4

High V

o

lta

g

e

L

o

w

V

olta

g

e

H4

H

3

H2

H1

H2

H

3

H4

X1

X2

X

3

X4

X

3

X2

X1

Hi

g

h

V

olta

ge

X3

X4

X2

X1

H1

H2

L

o

w

V

olta

ge

Hi

g

hV

o

lta

ge

X

3

X4

X2

X1

H1

H2

H4

H

3

L

o

w

V

olta

ge

L

o

w

V

olta

ge

Hi

g

h

V

o

lta

g

e

X

3

X4

X2

X1

H4

H

3

H1

H2

L

o

w

V

olta

ge

Hi

g

h

V

olta

ge

X

3

X4

X2

X1

H4

H

3

H1

H2

L

o

wV

o

lta

ge

X

3

X4

X2

X1

H4

H

3

H1

H2

Hi

g

h

V

olta

ge

L

o

wV

o

lta

ge

X

3

X4

X2

X1

H1

H2

H4

H

3

Hi

g

h

V

olta

ge

N

eut

r

al

X2

X4

X2

X4

X2

X4

High V

o

ltag

e

L

o

w Volta

g

e

H

3

H1

H

3

H1

H

3

H1

H2

H4

H2

H4

X1

X3

X1

X3

X1

X3

L

o

w

V

olta

g

e

X

3

X4

X1

X2

H4

H

3

H1

H2

X

3

X4

X1

X2

H4

H

3

H1

H2

X

3

X4

X1

X2

H4

H

3

Neut

r

al

H

i

g

hV

o

lta

ge

Hi

g

h Volta

g

e

X

3

X4

X2

X1

H1

H4

L

o

wV

o

lta

ge

L

o

wV

o

lta

ge

X

3

X4

X2

X1

H4

H

3

H1

H2

Hi

g

h

V

olta

g

e

L

o

w

V

olta

ge

Hi

g

hV

o

lta

ge

H

4

H

3

H

2

H

1

H

1

H2 H

3

H

4

X4

X

3

X2

X1

X2

X

3

X4

L

o

w

V

olta

g

e

Hi

g

hV

o

lta

ge

X

3

X4

X2

X1

H1

H2

H4

H

3

Hi

g

h

V

olta

ge

V

o

X4

X

3

X1

X2

X

3

X4

X2

X1

H4

H

3

H2

H

3

H4

Hi

g

h

V

olta

g

e

L

o

w

V

olta

ge

H4

H1

H4

X4

X

3

X1

X2

X

3

X4

X2

X1

X4

X

3

X

3

X4

Hi

g

hV

o

lta

ge

L

o

w

V

olta

ge

H2

H1

H2

X1

X2

X1

Diagram A Diagram B Diagram C

Diagram D Diagram E Diagram F

Diagram G Diagram H Diagram I

Diagram J Diagram K Diagram L

Diagram M Diagram N Diagram O 

Diagram P Diagram Q Diagram R 

Diagram S Diagram T Diagram U

April 2009

44-18

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single- and Three-Phase

Table 44-19. Selection Information

kVA °C Temp.

Rise

Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Frame Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

120 x 240 Volts to 12/24 Volts

.05

.10

.15

115

6-1/2

3-7/8

3-1/2

7

8

165

98

89

3

4

FR52

FR54

FR55

S10N04A81N

S10N04A82N

S10N04A83N

.25

.50

.75

115

6-1/2

8-3/8

4-7/8

6

3-7/8

4-5/8

5-3/4

12

13

21

165

213

124

152

98

117

146

5

10

FR56

FR57

FR58A

S10N04A26N

S10N04A51N

S10N04A76N

1

1.5

2

115

8-3/8

10-3/4

6

6-3/16

5-3/4

6-1/8

31

40

213

273

152

157

146

156

14

18

FR59A

FR67

FR68

S10N04A01N

S10N04A16N

S10N04A02N

3

5

7.5

115

14-1/8

16

7-11/16

10-3/8

8

9-7/8

65

113

123

359

406

195

263

203

251

29

51

55

FR176

FR177

FR178

S10N04A03N

S10N04A05N

S10N04A07N

120 x 240 Volts to 16/32 Volts

.05

.10

.15

115

6-1/2

3-7/8

3-1/2

7

8

165

98

89

3

4

FR52

FR54

FR55

S10N06A81N

S10N06A82N

S10N06A83N

.25

.50

.75

115

6-1/2

8-3/8

4-7/8

6

3-7/8

4-5/8

5-3/4

12

13

21

165

213

124

152

98

117

146

5

10

FR56

FR57

FR58A

S10N06A26N

S10N06A51N

S10N06A76N

1

1.5

2

115

8-3/8

10-3/4

6

6-3/16

5-3/4

6-1/8

31

40

213

273

152

157

146

156

14

18

FR59A

FR67

FR68

S10N06A01N

S10N06A16N

S10N06A02N

3

5

7.5

115

14-1/8

16

7-11/16

10-3/8

8

9-7/8

65

113

123

359

406

195

263

203

251

29

51

55

FR176

FR177

FR178

S10N06A03N

S10N06A05N

S10N06A07N

240 x 480 Volts to 24/48 Volts

.05

.10

.15

115

6-1/2

3-7/8

3-1/2

7

8

165

98

89

3

4

FR52

FR54

FR55

S20N08A81N

S20N08A82N

S20N08A83N

.25

.50

.75

115

6-1/2

8-3/8

4-7/8

6

3-7/8

4-5/8

5-3/4

12

13

21

165

213

124

152

98

117

146

5

10

FR56

FR57

FR58A

S20N08A26N

S20N08A51N

S20N08A76N

1

1.5

2

115

8-3/8

10-3/4

6

6-3/16

5-3/4

6-1/8

31

40

213

273

152

157

146

156

14

18

FR59A

FR67

FR68

S20N08A01N

S20N08A16N

S20N08A02N

3

5

7.5

115

14-1/8

16

7-11/16

10-3/8

8

9-7/8

65

113

123

359

406

195

263

203

251

29

51

55

FR176

FR177

FR178

S20N08A03N

S20N08A05N

S20N08A07N

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-19

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single-Phase

Table 44-20. Single-Phase 115 Volt Output Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

84 91 96 100 102

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

—

.13

—

1.14

—

.18

—

1.56

—

.24

—

.48

2.09

—

4.17

—

.31

—

2.70

—

.36

—

3.13

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

.26

—

.39

2.29

—

3.44

.36

—

.54

3.12

—

4.69

—

.72

—

6.25

—

.62

—

.93

5.41

—

8.12

.72

—

1.08

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

—

.659

—

5.73

—

.899

—

7.81

—

1.2

—

2.4

10.4

—

20.8

—

1.56

—

13.5

—

1.8

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

1.32

—

1.98

11.5

—

17.2

1.8

—

2.7

15.6

—

23.4

—

3.6

—

31.2

—

3.11

—

4.67

27.1

—

40.6

3.59

—

5.39

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

—

2.64

—

22.9

—

3.59

—

31.2

—

4.79

—

7.2

41.7

—

62.5

—

6.23

—

54.1

—

7.19

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

3.95

—

5.27

34.4

—

45.8

5.39

—

7.19

46.9

—

62.5

—

9.58

—

83.3

—

9.34

—

12.5

81.2

—

108

10.8

—

14.4

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

—

7.92

—

68.7

—

10.77

—

93.6

—

14.37

—

23.95

125.1

—

208.5

—

18.69

—

162.3

—

21.57

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

13.2

—

19.8

115

—

172

18

—

27

156

—

234

—

36

—

312

—

31.15

—

46.7

270.5

—

406

35.95

—

53.9

312.5

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram DBBCA

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

105 127 130 138 146

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

.48

—

.96

4.17

—

8.33

.54

—

1.1

4.58

—

9.17

—

.41

—

3.54

—

.29

—

.58

2.5

—

5.0

—

.23

—

1.98

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

—

1.44

—

12.5

—

1.6

—

13.7

—

.82

—

1.3

7.08

—

10.6

—

.87

—

7.5

—

.46

—

.69

3.95

—

5.93

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

2.39

—

4.79

20.8

—

41.6

2.63

—

5.27

22.9

—

45.8

—

2.03

—

17.7

—

1.44

—

2.87

12.5

—

25

—

1.14

—

9.88

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

—

7.19

—

62.4

—

7.9

—

68.7

—

4.07

—

6.1

35.4

—

53.1

—

4.31

—

37.5

—

2.27

—

3.41

19.8

—

29.6

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

9.58

—

14.4

83.3

—

125

10.5

—

15.8

91.7

—

137

—

8.14

—

70.8

—

5.75

—

8.62

50

—

75

—

4.55

—

39.5

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

—

19.2

—

16.7

—

21.1

—

183

—

12.2

—

16.3

106

—

142

—

11.5

—

100

—

6.82

—

9.10

59.3

—

79.2

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

28.7

—

47.9

249.9

—

416.5

31.5

—

52.5

275.1

—

458.5

—

24.4

—

212.4

—

17.3

—

28.7

150

—

250

—

13.6

—

118.5

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

—

71.9

—

624

—

79

—

687

—

40.7

—

61

354

—

531

—

43.1

—

357

—

22.7

—

34.1

197.5

—

296

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram AAABB

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . DT-1

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

April 2009

44-20

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single-Phase

Table 44-21. Single-Phase 120 Volt Output Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

88 95 100 104 106

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

—

.14

—

1.15

—

.19

—

1.56

—

.25

—

.50

2.09

—

4.17

—

.33

—

2.70

—

.38

—

3.13

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

.28

—

.41

2.29

—

3.44

.38

—

.56

3.12

—

4.69

—

.75

—

6.25

—

.65

—

.98

5.41

—

8.12

.75

—

1.12

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

—

.687

—

5.73

—

.937

—

7.81

—

1.25

—

2.5

10.4

—

20.8

—

1.62

—

13.5

—

1.87

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

1.37

—

2.06

11.5

—

17.2

1.87

—

2.82

15.6

—

23.4

—

3.75

—

31.2

—

3.25

—

4.87

27.1

—

40.6

3.75

—

5.62

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

—

2.75

—

22.9

—

3.75

—

31.2

—

5

—

7.5

41.7

—

62.5

—

6.5

—

54.1

—

7.5

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

4.12

—

5.5

34.4

—

45.8

5.62

—

7.5

46.9

—

62.5

—

10

—

83.3

—

9.75

—

13

81.2

—

108

11.2

—

15

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

—

8.25

—

68.7

—

11.25

—

93.6

—

15

—

25

125.1

—

208.5

—

19.5

—

162.3

—

22.5

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

13.75

—

20.6

114.5

—

172

18.75

—

28.2

156

—

234

—

37.5

—

312

—

32.5

—

48.7

270.5

—

406

37.5

—

56.2

312.5

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram DB BCA

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

109 132 136 144 152

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

.5

—

1.0

4.17

—

8.33

.55

—

1.1

4.58

—

9.17

—

.43

—

3.54

—

.3

—

.6

2.5

—

5.0

—

.24

—

1.98

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

—

1.5

—

12.5

—

1.6

—

13.7

—

.85

—

1.27

7.08

—

10.6

—

.9

—

7.5

—

.48

—

.71

3.95

—

5.93

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

2.5

—

5

20.8

—

41.6

2.75

—

5.5

22.9

—

45.8

—

2.12

—

17.7

—

1.5

—

3

12.5

—

25

—

1.19

—

9.88

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

—

7.5

—

62.4

—

8.25

—

68.7

—

4.25

—

6.37

35.4

—

53.1

—

4.5

—

37.5

—

2.37

—

3.56

19.8

—

29.6

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

10

—

15

83.3

—

125

11

—

16.5

91.7

—

137

—

8.5

—

70.8

—

6

—

9

50

—

75

—

4.75

—

39.5

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

—

20

—

167

—

22

—

183

—

12.7

—

17

106

—

142

—

12

—

100

—

7.12

—

9.5

59.3

—

79.2

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

30

—

50

249.9

—

416.5

33

—

55

275.1

—

458.5

—

25.5

—

212.4

—

18

—

30

150

—

250

—

14.25

—

118.5

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

—

75

—

624

—

82.5

—

687

—

42.5

—

63.7

354

—

531

—

45

—

375

—

23.7

—

35.6

197.5

—

296

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram AAABB

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-21

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single-Phase

Table 44-22. Single-Phase 230 Volt Output Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

199 203 207 209 216

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

—

.31

—

1.36

—

.36

—

1.56

—

.43

—

.86

1.88

—

3.75

.48

—

.96

2.08

—

4.17

—

.72

—

3.12

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

.62

—

.93

2.71

—

4.06

.72

—

1.08

3.12

—

4.69

—

1.29

—

5.62

—

1.44

—

6.25

—

1.44

—

2.16

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

—

1.55

—

6.77

—

1.8

—

7.81

—

2.15

—

4.31

9.37

—

18.7

2.39

—

4.79

10.4

—

20.8

—

3.59

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

3.11

—

4.66

13.5

—

20.3

3.6

—

5.4

15.6

—

23.4

—

6.46

—

28.2

—

7.19

—

31.2

—

7.19

—

10.8

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

—

6.23

—

27.1

—

7.2

—

31.2

—

8.62

—

12.9

37.5

—

56.2

9.58

—

14.4

41.7

—

62.5

—

14.4

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

9.34

—

12.5

40.6

—

54.2

10.8

—

14.4

46.9

—

62.5

—

17.2

—

75

—

19.2

—

83.3

—

21.6

—

28.7

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

—

18.6

—

81.3

—

21.6

—

93.6

—

25.8

—

43.1

112.5

—

187.5

28.7

—

47.9

125.1

—

208.5

—

43.2

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

31.1

—

46.6

135.5

—

203

36

—

54

156

—

234

—

64.6

—

282

—

71.9

—

312

—

72

—

108

312.5

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram GF GF E

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

219 242 246 253 260

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

.96

—

1.92

4.16

—

8.33

1.0

—

2.01

4.38

—

8.75

—

.77

—

3.34

—

.53

—

1.05

2.29

—

4.58

—

.41

—

1.77

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

—

2.87

—

12.5

—

3.02

—

13.1

—

1.53

—

2.3

6.67

—

10.0

—

1.58

—

6.87

—

.82

—

1.22

3.54

—

5.31

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

4.79

—

9.58

20.8

—

41.6

5.03

—

10.1

21.9

—

43.7

—

3.83

—

16.7

—

2.63

—

5.27

11.5

—

22.9

—

2.04

—

8.85

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

—

14.4

—

62.4

—

15.1

—

65.6

—

7.67

—

11.5

33.3

—

50

—

7.9

—

34.4

—

4.07

—

6.11

17.7

—

26.6

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

19.2

—

28.7

83.3

—

125

20.1

—

30.2

87.5

—

131

—

15.3

—

66.7

—

10.5

—

15.8

45.8

—

68.7

—

8.15

—

35.4

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

—

38.3

—

167

—

40.2

—

175

—

23

—

30.7

100

—

133

—

21.1

—

91.7

—

12.2

—

16.3

53.1

—

70.8

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

57.6

—

96

249.9

—

416.5

60.3

—

100.5

262.5

—

437.5

—

45.9

—

200.1

—

31.5

—

52.5

137.4

—

229

—

24.4

—

106.2

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

—

144

—

624

—

151

—

656

—

76.5

—

115

333.5

—

500

—

79

—

344

—

40.7

—

61.1

177

—

266

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram EE E F F

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-22

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single-Phase

Table 44-23. Single-Phase 240 Volt Output Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

208 212 216 218 225

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

—

.32

—

1.35

—

.38

—

1.56

—

.45

—

.9

1.88

—

3.75

.5

—

1.0

2.08

—

4.17

—

.75

—

3.12

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

.65

—

.98

2.71

—

4.06

.75

—

1.12

3.12

—

4.69

—

1.35

—

5.62

—

1.5

—

6.25

—

1.5

—

2.25

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

—

1.62

—

6.77

—

1.87

—

7.81

—

2.25

—

4.5

9.37

—

18.7

2.5

—

5

10.4

—

20.8

—

3.75

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

3.25

—

4.87

13.5

—

20.3

3.75

—

5.62

15.6

—

23.4

—

6.75

—

28.2

—

7.5

—

31.2

—

7.5

—

11.2

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

—

6.5

—

27.1

—

7.5

—

31.2

—

9

—

13.5

37.5

—

56.2

10

—

15

41.7

—

62.5

—

15

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

9.75

—

13

40.6

—

54.2

11.2

—

15

46.9

—

62.5

—

18

—

75

—

20

—

83.3

—

22.5

—

30

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

—

19.5

—

81.3

—

22.5

—

93.6

—

27

—

45

112.5

—

187

30

—

50

125.1

—

208

—

45

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

32.5

—

48.7

135

—

203

37.5

—

56.2

156

—

234

—

67.5

—

282

—

75

—

312

—

75

—

112

312

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram GF GF E

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

229 252 256 264 272

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.05

.10

1.0

—

2.0

4.16

—

8.33

1.05

—

2.1

4.38

—

8.75

—

.8

—

3.33

—

.55

—

1.1

2.29

—

4.58

—

.42

—

1.77

—

S10N04A81N

S10N06A81N

S10N04A82N

1

.10

.15

—

3.0

—

12.5

—

3.15

—

13.1

—

1.6

—

2.4

6.67

—

10.0

—

1.65

—

6.87

—

.85

—

1.27

3.54

—

5.31

S10N06A82N

S10N04A83N

S10N06A83N

1

.25

.50

5

—

10

20.8

—

41.6

5.25

—

10.5

21.9

—

43.7

—

4

—

16.7

—

2.75

—

5.5

11.5

—

22.9

—

2.12

—

8.85

—

S10N04A26N

S10N06A26N

S10N04A51N

1

.50

.75

—

15

—

62.4

—

15.7

—

65.6

—

8

—

12

33.3

—

50

—

8.25

—

34.4

—

4.25

—

6.37

17.7

—

26.6

S10N06A51N

S10N04A76N

S10N06A76N

1

1.5

20

—

30

83.3

—

125

21

—

31.5

87.5

—

131

—

16

—

66.7

—

11

—

16.5

45.8

—

68.7

—

8.5

—

35.4

—

S10N04A01N

S10N06A01N

S10N04A16N

1

1.5

2

—

40

—

167

—

42

—

175

—

24

—

32

100

—

133

—

22

—

91.7

—

12.7

—

17

53.1

—

70.8

S10N06A16N

S10N04A02N

S10N06A02N

1

3

5

60

—

100

249.9

—

416.5

63

—

105

262.5

—

437.5

—

48

—

200.1

—

33

—

55

137.4

—

229

—

25.5

—

106.2

—

S10N04A03N

S10N06A03N

S10N04A05N

1

5

7.5

—

150

—

624

—

157

—

656

—

80

—

120

333

—

500

—

82.5

—

344

—

42.5

—

63.7

177

—

266

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram EEEFF

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-23

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-24. Three-Phase Open Delta Connection 230 Volt Output Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

199 203 207 209 216

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

2

.05

.10

—

.54

—

1.35

—

.62

—

1.56

—

.75

—

1.49

1.87

—

3.75

.83

—

1.66

2.08

—

4.17

—

1.24

—

3.12

—

S10N04A81N

S10N06A81N

S10N04A82N

2

.10

.15

1.08

—

1.62

2.71

—

4.06

1.24

—

1.87

3.12

—

4.69

—

2.24

—

5.62

—

2.49

—

6.25

—

2.49

—

3.73

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

2

.25

.50

—

2.7

—

6.77

—

3.11

—

7.81

—

3.3

—

7.47

9.37

—

18.7

4.15

—

8.3

10.4

—

20.8

—

6.22

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

2

.50

.75

5.39

—

8.09

13.5

—

20.3

6.22

—

9.33

15.6

—

23.4

—

11.2

—

28.2

—

12.4

—

31.2

—

12.4

—

18.7

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

2

1

1.5

—

10.8

—

27.1

—

12.4

—

31.2

—

14.9

—

22.4

37.5

—

56.2

16.6

—

24.9

41.7

—

62.5

—

24.9

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

2

1.5

2

16.2

—

21.6

40.6

—

54.2

18.7

—

24.9

46.9

—

62.5

—

29.9

—

75

—

33.2

—

83.3

—

37.3

—

49.8

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

2

3

5

—

32.4

—

81.3

—

32.7

—

93.6

—

44.7

—

74.7

112.5

—

187

49.8

—

83

125.1

—

208

—

74.7

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

2

5

7.5

53.9

—

80.9

135

—

203

62.2

—

93.3

156

—

234

—

112

—

282

—

124

—

312

—

124

—

187

312.5

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram LKLKI

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

219 242 246 253 260

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

2

.05

.10

1.66

—

3.32

4.17

—

8.33

1.74

—

3.48

4.37

—

8.75

—

1.33

—

3.33

—

.91

—

1.83

2.29

—

4.58

—

.70

—

1.77

—

S10N04A81N

S10N06A81N

S10N04A82N

2

.10

.15

—

4.98

—

12.5

—

5.23

—

13.1

—

2.65

—

3.98

6.67

—

10.0

—

2.74

—

6.87

—

1.41

—

2.12

3.54

—

5.13

S10N06A82N

S10N04A83N

S10N06A83N

2

.25

.50

8.3

—

16.6

20.8

—

41.7

8.71

—

17.4

21.9

—

43.7

—

6.64

—

16.7

—

4.56

—

9.73

11.5

—

22.9

—

3.52

—

8.85

—

S10N04A26N

S10N06A26N

S10N04A51N

2

.50

.75

—

24.9

—

62.4

—

26.1

—

65.6

—

13.3

—

19.9

33.3

—

50

—

13.7

—

34.4

—

7.05

—

10.6

17.7

—

26.6

S10N06A51N

S10N04A76N

S10N06A76N

2

1

1.5

33.2

—

49.8

83.3

—

125

34.8

—

52.3

87.5

—

131

—

26.5

—

66.7

—

18.3

—

27.4

45.8

—

68.7

—

14.1

—

35.4

—

S10N04A01N

S10N06A01N

S10N04A16N

2

1.5

2

—

66.4

—

167

—

69.7

—

175

—

39.8

—

53.1

100

—

133

—

36.5

—

91.7

—

21.2

—

28.2

53.1

—

70.8

S10N06A16N

S10N04A02N

S10N06A02N

2

3

5

99.6

—

166

249.9

—

417

104.4

—

174

262.5

—

437

—

79.5

—

200

—

54.9

—

91.3

137.4

—

229

—

42.3

—

106.2

—

S10N04A03N

S10N06A03N

S10N04A05N

2

5

7.5

—

249

—

624

—

261

—

656

—

133

—

199

333

—

500

—

137

—

344

—

70.5

—

106

177

—

266

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram IIIKK

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-24

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-25. Three-Phase Open Delta Connection 240 Volt Output Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

208 212 216 218 225

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

2

.05

.10

—

.56

—

1.35

—

.65

—

1.56

—

.73

—

1.56

1.87

—

3.75

.87

—

1.73

2.08

—

4.17

—

1.3

—

3.12

—

S10N04A81N

S10N06A81N

S10N04A82N

2

.10

.15

1.13

—

1.69

2.71

—

4.06

1.3

—

1.95

3.12

—

4.69

—

2.34

—

5.62

—

2.6

—

6.25

—

2.6

—

3.9

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

2

.25

.50

—

2.81

—

6.77

—

3.25

—

7.81

—

3.9

—

7.79

9.37

—

18.7

4.33

—

8.66

10.4

—

20.8

—

6.49

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

2

.50

.75

5.63

—

8.44

13.5

—

20.3

6.5

—

9.75

15.6

—

23.4

—

11.7

—

28.2

—

13

—

31.2

—

13

—

19.5

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

2

1

1.5

—

11.3

—

27.1

—

13

—

31.2

—

15.6

—

23.4

37.5

—

56.2

17.3

—

26

41.7

—

62.5

—

26

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

2

1.5

2

16.9

—

22.5

40.6

—

54.2

19.5

—

26

46.9

—

62.5

—

31.2

—

75

—

34.6

—

83.3

—

39

—

52

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

2

3

5

—

33.9

—

81.3

—

39

—

93.6

—

46.8

—

77.9

112.5

—

187

51.9

—

86.6

125.1

—

208

—

78

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

2

5

7.5

56.3

—

84.4

135

—

203

65

—

97.5

156

—

234

—

117

—

282

—

130

—

312

—

130

—

195

312

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram LKLKI

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

229 252 256 264 272

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

2

.05

.10

1.73

—

3.46

4.16

—

8.33

1.82

—

3.64

4.37

—

8.75

—

1.38

—

3.33

—

.95

—

1.91

2.29

—

4.58

—

.74

—

1.77

—

S10N04A81N

S10N06A81N

S10N04A82N

2

.10

.15

—

5.19

—

12.5

—

5.45

—

13.1

—

2.77

—

4.15

6.67

—

10.0

—

2.86

—

6.87

—

1.47

—

2.21

3.54

—

5.31

S10N06A82N

S10N04A83N

S10N06A83N

2

.25

.50

8.66

—

17.3

20.8

—

41.6

9.09

—

18.2

21.9

—

43.7

—

6.92

—

16.7

—

4.76

—

9.53

11.5

—

22.9

—

3.68

—

8.85

—

S10N04A26N

S10N06A26N

S10N04A51N

2

.50

.75

—

26

—

62.4

—

27.3

—

65.6

—

13.8

—

20.8

33.3

—

50

—

14.3

—

34.4

—

7.36

—

11

17.7

—

26.6

S10N06A51N

S10N04A76N

S10N06A76N

2

1

1.5

34.6

—

51.9

83.3

—

125

36.4

—

54.5

87.5

—

131

—

27.7

—

66.7

—

19.1

—

28.6

45.8

—

68.7

—

14.7

—

35.4

—

S10N04A01N

S10N06A01N

S10N04A16N

2

1.5

2

—

69.3

—

167

—

72.7

—

175

—

41.5

—

55.4

100

—

133

—

38.1

—

91.7

—

22.1

—

29.4

53.1

—

70.8

S10N06A16N

S10N04A02N

S10N06A02N

2

3

5

103.8

—

173

249.9

—

416

109.2

—

182

262.5

—

437

—

83.1

—

200

—

57.3

—

95.3

137.4

—

229

—

44.1

—

106.2

—

S10N04A03N

S10N06A03N

S10N04A05N

2

5

7.5

—

260

—

624

—

273

—

656

—

138

—

208

333

—

500

—

143

—

344

—

73.6

—

110

177

—

266

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram IIIKK

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-25

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-26. Three-Phase Wye Connection 208 Volt Output Required, 60 Hz

Note: WARNING! Three-phase autotransformers should never be used to obtain 4-wire output with 3-wire input. 4-wire output requires

4-wire wye input.

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

152 164 173 180 184

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

—

.41

—

1.15

—

.56

—

1.56

—

.75

—

1.50

2.08

—

4.17

—

.98

—

2.71

—

1.12

—

3.12

—

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

.82

—

1.24

2.29

—

3.44

1.12

—

1.69

3.12

—

4.69

—

2.25

—

6.25

—

1.95

—

2.92

5.41

—

8.12

2.25

—

3.73

6.25

—

9.37

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

—

2.06

—

5.73

—

2.81

—

7.81

—

3.75

—

7.5

10.4

—

20.8

—

4.87

—

13.5

—

5.62

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

4.12

—

6.19

11.5

—

17.2

5.62

—

8.44

15.6

—

23.4

—

11.2

—

31.2

—

9.75

—

14.6

27.1

—

40.6

11.2

—

16.8

31.2

—

46.8

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

—

8.25

—

22.9

—

11.2

—

31.2

—

15

—

22.5

41.7

—

62.5

—

19.5

—

54.1

—

22.5

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

12.4

—

16.5

34.4

—

45.8

16.9

—

22.5

46.9

—

62.5

—

30

—

83.3

—

29.2

—

39

81.2

—

108

33.7

—

45

93.7

—

125

S10N06A16N

S10N04A02N

S10N06A02N

3

5

—

24.7

—

68.7

—

33.6

—

93.6

—

45

—

75

125

—

208

—

58.5

—

162.3

—

67.5

—

187.5

—

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

41.2

—

61.9

115

—

172

56.2

—

84.4

156

—

234

—

112

—

312

—

97.5

—

146

271

—

406

112

—

168

312

—

468

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram PNNOM

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

189 229 236 250 264

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

1.5

—

3.0

4.16

—

8.33

1.65

—

3.3

4.58

—

9.17

—

1.27

—

3.54

—

.9

—

1.8

2.5

—

5.0

—

.71

—

1.98

—

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

—

4.5

—

12.5

—

4.95

—

13.7

—

2.55

—

3.82

7.08

—

10.6

—

2.7

—

7.5

—

1.42

—

2.14

3.95

—

5.93

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

7.5

—

15

20.8

—

41.6

8.25

—

16.5

22.9

—

45.8

—

6.35

—

17.7

—

4.5

—

9

12.5

—

25

—

3.56

—

9.88

—

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

—

22.5

—

62.4

—

24.7

—

68.7

—

12.7

—

19

35.4

—

53.1

—

13.5

—

37.5

—

7.12

—

10.7

19.3

—

29.3

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

30

—

45

83.3

—

125

33

—

49.5

91.7

—

137

—

25.5

—

70.8

—

18

—

27

50

—

75

—

14.2

—

39.5

—

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

—

60

—

167

—

66

—

183

—

38.2

—

51

106

—

142

—

361

—

100

—

21.4

—

28.5

59.3

—

79.2

S10N06A16N

S10N04A02N

S10N06A02N

3

5

90

—

150

249.9

—

416

99

—

165

275.1

—

458

—

76.5

—

212.4

—

54

—

90

150

—

250

—

46.2

—

118.5

—

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

—

225

—

624

—

274

—

687

—

127

—

190

354

—

531

—

135

—

375

—

71.2

—

107

198

—

293

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram MMMN N

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-26

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-27. Three-Phase Wye Connection 230 Volt Output Required, 60 Hz

Note: WARNING! Three-phase autotransformers should never be used to obtain 4-wire output with 3-wire input. 4-wire output requires

4-wire wye input.

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

183 192 199 208 218

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

—

.62

—

1.56

—

.83

—

1.66

2.08

—

4.17

—

.54

—

1.35

—

1.65

—

3.3

4.58

—

9.17

1.66

—

3.32

4.17

—

8.35

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

1.25

—

1.87

3.12

—

4.69

—

2.49

—

6.25

—

1.08

—

1.62

2.71

—

4.06

—

4.95

—

13.7

—

4.98

—

12.5

—

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

—

3.11

—

7.81

—

4.15

—

8.3

10.4

—

20.8

—

2.70

—

6.77

—

8.2

—

16.5

22.9

—

45.8

8.3

—

16.6

20.9

—

41.7

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

6.22

—

9.33

15.6

—

23.4

—

12.4

—

31.2

—

5.39

—

8.09

13.5

—

20.3

—

24.7

—

68.8

—

24.9

—

62.6

—

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

—

12.5

—

31.2

—

16.6

—

24.9

41.7

—

62.5

—

10.8

—

27.1

—

33

—

49.5

91.7

—

137

33.2

—

49.8

83.5

—

125

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

18.7

—

24.9

46.9

—

62.5

—

33.2

—

83.3

—

16.2

—

21.6

40.6

—

54.2

—

66

—

183

—

66.4

—

167

—

S10N06A16N

S10N04A02N

S10N06A02N

3

5

—

37.5

—

93.6

—

49.8

—

83

125.1

—

208

—

32.4

—

81.3

—

99

—

165

275

—

458

99.6

—

166

250.5

—

417

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

62.2

—

93.3

156

—

234

—

124

—

312

—

53.9

—

80.9

135

—

203

—

247

—

688

—

249

—

626

—

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram NNSMQ

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

242 245 253 260 265

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

1.74

—

3.48

4.37

—

8.75

—

1.33

—

3.33

—

.91

—

1.83

2.29

—

4.58

—

.70

—

1.77

—

.62

—

1.56

—

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

—

5.23

—

13.1

—

2.65

—

3.98

6.67

—

10.0

—

2.74

—

6.87

—

1.41

—

2.12

3.54

—

5.31

1.25

—

1.87

3.12

—

4.69

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

8.71

—

17.4

21.9

—

43.7

—

6.63

—

16.7

—

4.56

—

9.31

11.5

—

22.9

—

3.52

—

8.85

—

3.11

—

7.81

—

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

—

26.1

—

65.6

—

13.3

—

19.9

33.3

—

50

—

13.7

—

34.4

—

7.05

—

10.6

17.7

—

26.6

6.22

—

9.33

15.6

—

23.4

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

34.8

—

52.3

87.5

—

131

—

26.5

—

66.7

—

18.3

—

27.4

45.8

—

68.7

—

14.1

—

35.4

—

12.5

—

31.2

—

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

—

69.7

—

175

—

39.8

—

53.1

100

—

133

—

36.6

—

91.6

—

21.2

—

28.2

53.1

—

70.8

18.7

—

24.9

46.9

—

62.5

S10N06A16N

S10N04A02N

S10N06A02N

3

5

104.4

—

174

262.5

—

437

—

79.5

—

200

—

54.9

—

91.3

137.4

—

229

—

42.3

—

106.2

—

37.5

—

93.6

—

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

—

261

—

656

—

133

—

199

333

—

500

—

137

—

344

—

70.5

—

106

177

—

266

62.2

—

93.3

156

—

234

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram QQRRS

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-27

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-28. Three-Phase Wye Connection 240 Volt Output Required, 60 Hz

Note: WARNING! Three-phase autotransformers should never be used to obtain 4-wire output with 3-wire input. 4-wire output requires

4-wire wye input.

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

190 200 208 218 228

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

—

.65

—

1.65

—

.86

—

1.73

2.08

—

4.17

—

1.27

—

3.05

—

.86

—

1.73

2.08

—

4.17

1.73

—

3.46

4.17

—

8.34

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

1.3

—

1.95

3.12

—

4.69

—

2.59

—

6.25

—

2.55

—

3.82

6.12

—

9.16

—

2.59

—

6.25

—

5.20

—

12.5

—

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

—

3.25

—

7.81

—

4.32

—

8.65

10.4

—

20.8

—

6.3

—

15.1

—

4.32

—

8.65

10.4

—

20.8

8.66

—

17.3

20.9

—

41.7

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

6.5

—

9.75

15.6

—

23.4

—

13

—

31.2

—

12.7

—

19.2

30.4

—

46

—

13

—

31.2

—

26

—

62.6

—

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

—

13

—

31.2

—

17.3

—

25.9

41.7

—

62.5

—

25.5

—

61.2

—

17.3

—

25.9

41.7

—

62.5

34.6

—

52

83.4

—

125

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

19.5

—

26

46.9

—

62.5

—

34.6

—

83.3

—

38.2

—

51

91.6

—

122.4

—

34.6

—

83.3

—

69.3

—

167

—

S10N06A16N

S10N04A02N

S10N06A02N

3

5

—

39

—

93.6

—

51.9

—

86.5

125.1

—

208

—

76.5

—

183.6

—

51.9

—

86.5

125.1

—

208

103.8

—

173

250.2

—

417

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

65

—

97.5

156

—

234

—

130

—

312

—

127.2

—

192

305.2

—

460

—

130

—

312

—

260

—

626

—

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram NNMRQ

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

252 256 264 272 277

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

1.85

—

3.64

4.37

—

8.75

—

1.39

—

3.33

—

.95

—

1.91

2.29

—

4.58

—

.74

—

1.77

—

.65

—

1.56

—

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

—

5.46

—

13.1

—

2.77

—

4.16

6.67

—

10.0

—

2.86

—

6.87

—

1.47

—

2.21

3.54

—

5.31

1.3

—

1.95

3.12

—

4.69

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

9.09

—

18.2

21.9

—

43.7

—

6.93

—

16.7

—

4.76

—

9.53

11.5

—

22.9

—

3.68

—

8.85

—

3.25

—

7.81

—

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

—

27.3

—

65.6

—

13.9

—

20.8

33.3

—

50

—

14.3

—

34.4

—

7.36

—

11

17.7

—

26.6

6.5

—

9.75

15.6

—

23.4

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

36.4

—

54.6

87.5

—

131

—

27.7

—

66.7

—

19.1

—

28.6

45.8

—

68.7

—

14.7

—

35.4

—

13

—

31.2

—

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

—

72.8

—

175

—

41.6

—

55.4

100

—

133

—

38.1

—

91.7

—

22.1

—

29.5

53.1

—

70.8

19.5

—

26

46.9

—

62.5

S10N06A16N

S10N04A02N

S10N06A02N

3

5

109.2

—

182

262.5

—

437

—

83.1

—

200

—

57.3

—

95.3

137.4

—

229

—

44.1

—

106.2

—

39

—

93.6

—

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

—

273

—

656

—

139

—

208

333

—

500

—

143

—

344

—

73.6

—

110

177

—

266

65

—

97.5

156

—

234

S10N06A05N

S10N04A07N

S10N06A07N

Connection Diagram QQRRS

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-28

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-29. Three-Phase Wye Connection 460 Volt Output Required, 60 Hz

Note: WARNING! Three-phase autotransformers should never be used to obtain 4-wire output with 3-wire input. 4-wire output requires

4-wire wye input.

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage Style

Number

Price

U.S. $

406 418 432 438 424 436 450

Output Output Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

3

.05

.10

—

1.25

—

1.57

—

1.66

—

3.31

2.08

—

4.15

—

2.49

—

3.12

—

3.22

—

6.62

4.04

—

8.31

—

1.3

—

1.7

1.56

—

2.1

—

3.5

—

4.2

—

2.6

—

3.13

—

S10N04A81N

S10N06A81N

S10N04A82N

3

.10

.15

2.49

—

3.73

3.12

—

4.68

—

4.97

—

6.24

—

4.97

—

7.46

6.24

—

9.36

—

9.94

—

12.48

—

2.6

—

3.9

3.12

—

4.68

—

5.2

—

6.25

—

5.2

—

7.8

6.25

—

9.38

S10N06A82N

S10N04A83N

S10N06A83N

3

.25

.50

—

6.22

—

7.81

—

8.28

—

16.6

10.39

—

20.84

—

12.4

—

15.56

—

16.6

—

33.2

20.84

—

41.67

—

6.5

—

7.82

—

8.7

—

17.4

10.4

—

20.9

—

13

—

15.6

—

S10N04A26N

S10N06A26N

S10N04A51N

3

.50

.75

12.5

—

18.7

15.69

—

23.47

—

24.8

—

31.12

—

24.69

—

37.3

31.25

—

46.82

—

49.6

—

62.25

—

13

—

19.5

15.6

—

23.4

—

26

—

31.2

—

26

—

39

31.2

—

46.9

S10N06A51N

S10N04A76N

S10N06A76N

3

1

1.5

—

24.9

—

31.25

—

33.1

—

49.7

41.54

—

62.38

—

49.7

—

62.38

—

66.2

—

99.4

83.09

—

124.75

—

26

—

31.2

—

35

—

52

42

—

62.5

—

52

—

62.5

—

S10N04A01N

S10N06A01N

S10N04A16N

3

1.5

2

37.3

—

49.7

46.94

—

62.38

—

66.3

—

83.22

—

74.6

—

99.5

93.63

—

124.88

—

133

—

166.93

—

39

—

52

46.8

—

62.5

—

69

—

82.9

—

78

—

104

93.8

—

125

S10N06A16N

S10N04A02N

S10N06A02N

3

5

—

74.6

—

93.63

—

99.3

—

166

124.64

—

208.35

—

149

—

187.01

—

198.6

—

322

249.27

—

404.16

—

78

—

93.8

—

104

—

174

125

—

209.2

—

156

—

187.6

—

S10N04A03N

S10N06A03N

S10N04A05N

3

5

7.5

125

—

187

156.89

—

235

—

248

—

311

—

249

—

373

312.53

—

468

—

496

—

622

—

130

—

195

156.3

—

234

—

260

—

312

—

260

—

390

312.7

—

469

S10N06A05N

S10N04A07N

S10N06A07N

Connection

Diagram 

RRQQRRQ

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-29

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Single-Phase

Table 44-30. Single-Phase Required, 60 Hz

Additional wiring trough may be required.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required 

Unit

kVA

Input Available Voltage/Output Voltage Style

Number

Price

U.S. $

200/240 230/277 346/380 362/380 378/416 416/457

Output Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.25

.50

.75

1.25

2.50

3.75

5.2

10.4

15.6

1.44

2.88

4.32

5.2

10.4

15.6

1.98

3.95

5.93

5.2

10.4

15.6

3.95

7.90

11.9

10.4

20.8

31.2

2.16

4.33

6.49

5.2

10.4

15.6

2.38

4.76

7.14

5.2

10.4

15.6

S20N08A26N

S20N08A51N

S20N08A76N

1

1.5

2

5.00

7.50

10.00

20.8

31.2

41.6

5.76

8.64

11.5

20.8

31.2

41.6

7.90

11.9

15.8

20.8

31.2

41.6

15.8

23.8

31.6

41.6

62.5

83.3

8.65

13.0

17.3

20.8

31.2

41.6

9.52

14.3

19.0

20.8

31.2

41.6

S20N08A01N

S20N08A16N

S20N08A02N

1

3

5

7.5

15.0

25.0

37.5

62.5

104.0

156.0

17.3

28.8

43.2

62.5

104.0

156.0

23.8

39.5

59.3

62.5

104.0

156.0

47.5

79.0

118.6

125.0

208.0

312.0

26.0

43.3

64.9

62.5

104.0

156.0

28.6

47.6

71.4

62.5

104.0

156.0

S20N08A03N

S20N08A05N

S20N08A07N

Connection

Diagram 

BBFEF F

Units

Required 

Unit

kVA

Input Available Voltage/Output Voltage Style

Number

Price

U.S. $

436/480 458/480 277/230 480/456 504/480 528/480

Output Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

1

.25

.50

.75

2.50

4.99

7.49

5.2

10.4

15.6

4.99

9.98

15.0

10.4

20.8

31.2

1.44

2.88

4.33

6.26

12.5

18.8

5.23

10.4

15.7

11.4

22.8

34.2

5.47

10.9

16.4

11.4

22.8

34.2

2.75

5.49

8.24

5.72

11.4

17.2

S20N08A26N

S20N08A51N

S20N08A76N

1

1.5

2

9.98

15.0

20.0

20.8

31.2

41.6

20.0

30.0

40.0

41.6

62.5

83.3

5.76

8.64

11.5

25.0

37.6

50.1

20.9

31.3

41.8

45.6

68.4

91.2

21.8

32.8

43.7

45.6

68.4

91.2

11.0

16.5

22.0

22.9

34.3

45.8

S20N08A01N

S20N08A16N

S20N08A02N

1

3

5

7.5

30.0

49.9

74.9

62.5

104.0

156.0

60.0

99.8

149.8

125.0

208.0

312.0

17.3

28.8

43.2

75.3

125.3

187.9

62.7

104.5

156.8

136.0

227.0

341.0

65.2

108.0

163.0

136.0

227.0

341.0

33.0

54.9

82.4

68.8

114.4

171.6

S20N08A03N

S20N08A05N

S20N08A07N

Connection

Diagram 

FEBEEF

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-30

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Three-Phase

Table 44-31. Three-Phase Required, 60 Hz

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Additional wiring trough may be required.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Unit

kVA

Input Available Voltage/Output Voltage Style

Number

Price

U.S. $

362/380 346/416 430/473 400/480 436/480

Output Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps kVA Amps

.25

.50

.75

6.52

13.0

19.6

10.4

20.8

31.2

3.75

7.50

11.2

5.2

10.4

15.6

4.26

8.52

12.8

5.2

10.4

15.6

4.33

8.65

13.0

5.2

10.4

15.6

4.33

8.65

13.0

5.2

10.4

15.6

S20N08A26N

S20N08A51N

S20N08A76N

1

1.5

2

26.1

39.1

52.2

41.6

62.4

83.2

15.0

22.5

30.0

20.8

31.2

41.6

17.0

25.5

34.1

20.8

31.2

41.6

17.3

26.0

34.6

20.8

31.2

41.6

17.3

26.0

34.6

20.8

31.2

41.6

S20N08A01N

S20N08A16N

S20N08A02N

3

5

7.5

78.4

130.4

195.6

125.0

208.0

312.0

45.0

75.1

112.6

62.5

104.0

156.0

51.2

85.2

127.8

62.5

104.0

156.0

52.0

86.6

129.9

62.5

104.0

156.0

52.0

86.6

129.9

62.5

104.0

156.0

S20N08A03N

S20N08A05N

S20N08A07N

Connection Diagram INKNK

Units Required 23232

Unit

kVA

Input Available Voltage/Output Voltage Style

Number

Price

U.S. $

460/483 457/380 504/480 528/480

Output Output Output Output

kVA Amps kVA Amps kVA Amps kVA Amps

.25

.50

.75

8.7

17.4

26.1

10.4

20.8

31.2

4.12

8.23

12.3

6.25

12.5

18.8

9.08

18.2

27.2

10.9

21.8

32.8

4.76

9.51

14.3

5.72

11.4

17.2

S20N08A26N

S20N08A51N

S20N08A76N

1

1.5

2

34.8

52.2

69.6

41.6

62.4

83.2

16.5

24.7

32.9

25.0

37.5

50.0

36.3

54.5

72.6

43.7

65.5

87.4

19.0

28.5

38.0

22.9

34.3

45.8

S20N08A01N

S20N08A16N

S20N08A02N

3

5

7.5

104.6

174.0

261.0

125.0

208.0

312.0

49.5

82.3

123.5

75.2

125.1

187.6

109.7

181.6

272.4

131.3

218.4

327.6

57.2

95.1

142.7

68.8

114.4

171.6

S20N08A03N

S20N08A05N

S20N08A07N

Connection Diagram INIK

Units Required 2322

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-31

Distribution & Control Transformers and Power Supplies

44

Buck-Boost and Low Voltage Lighting Transformers

Autotransformer Applications

Table 44-32. Three-Phase Open Delta Connection 480 Volt Output

Required, 60 Hz

Additional wiring trough may be required.

On transformers supplied with standard taps, taps must be placed at

nominal settings.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Table 44-33. Single-Phase 480 Volt Output Required, 60 Hz

Additional wiring trough may be required.

On transformers supplied with standard taps, taps must be placed at

nominal settings.

Refer to Page 44-17 for Buck-Boost wiring diagrams.

Note: Autotransformers can be used only where local electric codes

permit and isolation of the two circuits is not required.

Note: Output voltage for lower input voltage can be found by: x Input Actual Voltage = Output New Voltage.

Note: Output kVA available at reduced input voltage can be found by: x Output kVA = New kVA Rating.

Units

Required



Input Available Voltage Style

Number



Price

U.S.

600 575 575

Output Output Output

kVA Amps kVA Amps kVA Amps

2

4.3

—

6.5

5.1

—

7.8

—

4.1

—

4.9

—

S20N11S51N

S60G11S51N

S20N11S76N

2

—

8.6

—

10.3

—

6.2

—

8.3

7.4

—

9.9

S60G11S76N

S20N11S01N

S60G11S01N

2

13.0

—

17.2

15.6

—

20.6

—

12.4

—

14.9

—

S20N11S16N

S60G11S16N

S20N11S02N

2

—

25.8

—

31

—

16.5

—

24.8

19.8

—

29.8

S60G11S02N

S20N11S03N

S60G11S03N

2

43.2

—

65

51.9

—

78.1

—

41

—

49.3

—

S20N11S05N

S60G11S05N

S20N11S07N

2

—

86

—

103.4

—

83

—

99.8

62

—

74.5

—

S60G11S07N

S20N11S10N

S60G11S10N

2

130

—

216

156.3

—

259.8

—

124

—

149.1

—

S20N11S15N

S60N11S15N

T20P11S25

2

—

324

432

—

389.7

519.6

207

—

248.9

—

S60J11S25N

T20P11S37

T20P11S50

Connection

Diagram



IJT

Units

Required



Input Available Voltage Style

Number



Price

U.S.

600 575 575

Output Output Output

kVA Amps kVA Amps kVA Amps

1

2.5

—

3.7

5.2

—

7.7

—

2.4

—

5

—

S20N11S51N

S60G11S51N

S20N11S76N

1

—

5.0

—

10.4

—

3.6

—

4.8

7.5

—

10

S60G11S76N

S20N11S01N

S60G11S01N

1

7.5

—

10

15.6

—

20.8

—

7.2

—

15

—

S20N11S16N

S60G11S16N

S20N11S02N

1

—

15

—

31.2

—

9.6

—

14.3

20

—

29.7

S60G11S02N

S20N11S03N

S60G11S03N

1

25

—

37.5

52

—

78.1

—

24

—

50

—

S20N11S05N

S60G11S05N

S20N11S07N

1

—

50

—

104.1

—

43

—

100

36

—

75

—

S60G11S07N

S20N11S10N

S60G11S10N

1

75

—

125

156.2

—

260.4

—

72

—

150

—

S20N11S15N

S60N11S15N

T20P11S25

1

—

187

250

—

389.6

520.8

120

—

250

—

S60J11S25N

T20P11S37

T20P11S50

Connection

Diagram



EHU

Rated Output Voltage

Rated Input Voltage

--------------------------------------------------

Actual Input Voltage

Rated Input Voltage

------------------------------------------------

Discount Symbol. . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-32

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTA

Type MTA Transformer

Product Description

■Varnish impregnated core and

coil design.

■Suitable for indoor applications.

■Open core and coil design.

Application Description

Machine Tool and Industrial Control

Transformers provide stepped-down

voltages to machine tool control

devices enabling control circuits to

be isolated from all power and lighting

circuits. This allows the use of ground-

ed or ungrounded circuits that are

independent of the power or lighting

grounds; greater safety is afforded the

operator. The control transformer line

is particularly adaptable on applica-

tions where compact construction

is demanded.

Features, Beneﬁts

and Functions

■UL recognized component for units

rated 1000 VA and below.

■CSA certiﬁed for units rated 1000 VA

and below.

■55ºC rise, 105ºC insulation system.

■60 Hz operation standard.

■100% tested to verify product quality.

■Performance equals or exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

■Each unit must pass rigid tests for

turns ratio, insulation, continuity,

and over potential.

■50 – 5000 VA ratings.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribu-

tion and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI and IEEE Standards.

Product Speciﬁcations

Frequency

Cutler-Hammer Type MTA control

transformers are designed for 60 Hertz

operation. Transformers required for

other frequencies are available and

must be speciﬁcally designed.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-34. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Series-Multiple Windings

Series-multiple windings consist of

2 similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series), or 240

with a 120 mid-point.

The following pages provide listings for most

standard transformer ratings and styles.

For other ratings or styles not shown, refer

to Eaton.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

April 2009

CA08102001E For more information visit: www.eaton.com

44-33

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTA

Overcurrent Protection Tables

Overcurrent protection on both the primary and secondary sides of transformers are speciﬁed in UL 508 and the National

Electrical Code. The maximum acceptable ratings are shown below. Due to high inrush currents present when a transformer

is initially energized, it is recommended that the primary fuse be time delay to prevent nuisance trips during startup.

Table 44-35. Maximum Acceptable Rating of Primary Overcurrent Protection

Note: If the rated primary current is less than 2 amperes, the maximum rating of the overcurrent device is 300% for power circuits, shown

above, or 500% for control circuits, shown above (in brackets). If the rated primary current is 2 amperes or more, the maximum rating of the

overcurrent device is 250%. All ﬁgures assume secondary overcurrent protection per NEC/UL.

References: NEC 430-72 (c) exception 2, 450-3 (b) 1 & 2, UL 508 32.7, UL 845 11.16 and 11.17.

Table 44-36. Maximum Acceptable Rating of Secondary Overcurrent Protection

Note: If the rated secondary current is less than 9 amperes, the maximum rating of the overcurrent device is 167%; 9 amperes or more, the maximum

rating of the overcurrent device is 125%. If 125% does not correspond to a standard fuse rating, the next highest standard rating may be used.

References: NEC 430-72 (c) exception 2, 450-3 (b) 1 & 2, UL 508 32.7, UL 845 11.16 and 11.17.

Primary

Voltage

VA Rating

25 50 75 100 150 200 250 300 350 500 750 1000 1500 2000 3000 5000 7000

115 6/10

(1)

1-1/4

(2)

1-8/10

(3-2/10)

2-1/2

(4)

3-1/2

(6-1/4)

5

(8)

455810152025———

120 6/10

(1)

1-1/4

(2)

1-8/10

(3)

2-1/4

(4)

3-1/2

(6-1/4)

5

(8)

455810151520———

200 3/10

(6/10)

3/4

(1-1/4)

1-1/8

(1-8/10)

1-1/2

(2-1/2)

2-1/4

(3-1/2)

3

(5)

3-1/2

(6-1/4)

4-1/2

(7-1/2)

5

(8)

4-1/2 7 9 15 15 20 — —

208 3/10

(6/10)

6/10

(1-1/8)

1

(1-8/10)

1-4/10

(2-1/4)

2

(3-1/2)

2-8/10

(4-1/2)

3-1/2

(6)

4

(7)

5

(8)

46812152030—

220 3/10

(1/2)

6/10

(1-1/8)

1

(1-6/10)

1-1/4

(2-1/4)

2

(3-2/10)

2-1/2

(4-1/2)

3-2/10

(5-6/10)

4

(6-1/4)

4-1/2

(7-1/2)

46812152030—

230 3/10

(1/2)

6/10

(1)

8/10

(1-6/10)

1-1/4

(2)

1-8/10

(3-2/10)

2-1/2

(4)

3-2/10

(5)

3-1/2

(6-1/4)

4-1/2

(7-1/2)

46810152030—

240 3/10

(1/2)

6/10

(1)

8/10

(1-1/2)

1-1/4

(2)

1-8/10

(3)

2-1/4

(4)

3

(5)

3-1/2

(6-1/4)

4

(7)

3-1/2 5 7 10 15 20 30 —

277 1/4

(4/10)

1/2

(8/10)

8/10

(1-1/4)

1

(1-8/10)

1-6/10

(2-1/2)

2

(3-1/2)

2-1/2

(4-1/2)

3-2/10

(5)

3-1/2

(6-1/4)

5

(9)

569121525—

380 3/16

(3/10)

3/10

(6/10)

1/2

(8/10)

3/4

(1-1/4)

1-1/8

(1-8/10)

1-1/2

(2-1/2)

1-8/10

(3-2/10)

2-1/4

(3-1/2)

2-1/2

(4-1/2)

3-1/2

(6-1/4)

5-6/10

(9)

4-1/2 6-1/4 9 15 20 25

400 3/16

(3/10)

3/10

(6/10)

1/2

(8/10)

3/4

(1-1/4)

1-1/8

(1-8/10)

1-1/2

(2-1/2)

1-8/10

(3)

2-1/4

(3-1/2)

2-1/2

(4)

3-1/2

(6-1/4)

5-6/10

(9)

4-1/2 6-1/4 9 12 15 20

416 15/100

(3/10)

3/10

(6/10)

1/2

(8/10)

6/10

(1-1/8)

1

(1-8/10)

1-4/10

(2-1/4)

1-8/10

(3)

2

(3-1/2)

2-1/2

(4)

3-1/2

(6)

5

(9)

468121520

440 15/100

(1/4)

3/10

(1/2)

1/2

(8/10)

6/10

(1-1/8)

1

(1-6/10)

1-1/4

(2-1/4)

1-6/10

(2-8/10)

2

(3-2/10)

2-1/4

(3-1/2)

3-2/10

(5)

5

(8)

468121520

460 15/100

(1/4)

3/10

(1/2)

4/10

(8/10)

6/10

(1)

8/10

(1-1/2)

1-1/4

(2)

1-6/10

(2-1/2)

1-8/10

(3-2/10)

2-1/4

(3-2/10)

3-2/10

(5)

4-1/2

(8)

3-1/2 6 8 12 15 20

480 15/100

(1/4)

3/10

(1/2)

4/10

(3/4)

6/10

(1)

8/10

(1-1/2)

1-1/4

(2)

1-1/2

(2-1/2)

1-8/10

(3)

2

(3-1/2)

3

(5)

4-1/2

(7-1/2)

3-1/2 5 7 10 15 20

550 1/8

(2/10)

1/4

(4/10)

4/10

(6/10)

1/2

(8/10)

8/10

(1-1/4)

1

(1-8/10)

1-1/4

(2-1/4)

1-6/10

(2-1/2)

1-8/10

(3)

2-1/2

(4-1/2)

4

(6-1/4)

54-1/2 6 9 15 15

575 1/8

(2/10)

1/4

(4/10)

3/10

(6/10)

1/2

(8/10)

3/4

(1-1/4)

1

(1-6/10)

1-1/4

(2)

1-1/2

(2-1/2)

1-8/10

(3)

2-1/2

(4)

3

(6-1/4)

54-1/2 6 9 15 15

600 1/8

(2/10)

2/10

(4/10)

3/10

(6/10)

1/2

(8/10)

3/4

(1-1/4)

8/10

(1-6/10)

1-1/4

(2)

1-1/2

(2-1/2)

1-6/10

(2-8/10)

2-1/4

(4)

3-1/2

(6-1/4)

54691515

Secondary

Voltage

VA Rating

25 50 75 100 150 200 250 300 350 500 750 1000 1500 2000 3000 5000

12

24

3-1/2

1-6/10

7

3-2/10

10

5

15

6-1/4

20

10

30

12

—

15

—

20

—

20

—

30

—

90

95

100

4/10

8/10

1-1/4

1-8/10

1-6/10

2-1/2

3-1/2

3-2/10

4-1/2

4

5

6-1/4

6

5-6/10

9

8

12

15

30

20

30

—

110

115

120

3/10

3/4

6/10

1-1/8

1

1-1/2

1-4/10

1-1/4

2-1/4

2

3

2-8/10

2-1/2

3-1/2

3-2/10

4-1/2

4

5

4-1/2

7-1/2

7

6-1/4

10

15

20

30

20

—

220

230

240

15/100

3/10

1/2

3/4

6/10

1-1/8

1

1-1/2

1-4/10

1-1/4

1-8/10

1-6/10

2-1/4

2

2-1/2

3-1/2

3-2/10

5-6/10

5

7

9

8

15

12

20

30

April 2009

44-34

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Types MTA, MTC and AP

Wiring Diagrams

Type MTA and MTC Control Transformers

Table 44-37. Wiring for Diagram 1

Figure 44-2. Diagram 1

Table 44-38. Wiring for Diagram 2

Figure 44-3. Diagram 2

Table 44-39. Wiring for Diagram 3

Figure 44-4. Diagram 3

Table 44-40. Wiring for Diagram 4

Figure 44-5. Diagram 4

Type AP Control Transformers

Table 44-41. Wiring for Diagram 5

Figure 44-6. Diagram 5

Volts Connect Lines

AB

460

230

—

H2 to H3

H1 to H3 and H2 to H4

H1-H4

115 — — X1-X2

Volts Connect Lines

AB

575

460

230

—

416

380

—

208

H2 to H3

H1 to H3 and H2 to H4

H1 to H3 and H2 to H5

H1-H5

H1-H4

H1-H5

115

95

115

95

—

X1-X3

X1-X2

H1 H3 H2 H4

X2 X1

H1 H3 H2 H5

X3 X1

H4

X2

Volts Connect Lines

AB

460

230

—

H2 to H3

H1 to H3 and H2 to H4

H1-H4

230

115

—

X2 to X3

X1 to X3 and X2 to X4

X1-X4

Volts Connect Lines

AB

115 115 — H1-H2

12 24 — X1-X2

H1 H3 H2 H4

X4 X2 X3 X1

H1 H2

X2 X1

Volts Connect Lines

AB

480

240

—

H2 to H3

H1 to H3 and H2 to H4

H1-H4

240

115

—

X2 to X3

X1 to X3 and X2 to X4

X1-X4

H1 H3 H2 H4

X4 X2 X3 X1

April 2009

CA08102001E For more information visit: www.eaton.com

44-35

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTA

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-42. Type MTA

See Page 44-34 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Frame Wiring

Diagram 

Style

Number

Price

U.S.

Height Width Depth Height Width Depth

230/460 Volts to 115 Volts, 60 Hz

50 (Use Type MTC – C0050C2A)

75

100

3-3/16

3-3/4

4

3

4

80

95

102

1.4

1.8

FR1510

FR1512

1

C0075A2F

C0100A2F

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4-3/4

4-1/2

5

6

7

8

80

96

95

114

95

114

127

2.7

3.2

3.6

FR1520

FR1714

FR1717

1

C0150A2F

C0200A2F

C0250A2F

300

350

500

3-13/16

4-3/8

4-1/2

5-1/4

6

5-5/8

12

15

96

111

114

133

152

143

5.4

6.8

FR1730

FR1727

FR1923

1

C0300A2F

C0350A2F

C0500A2F

750

1000

1500

4-3/8

5-1/4

6

5-1/4

6-1/8

6-7/8

6-1/8

6-3/4

7-1/2

19

27

111

133

152

133

155

174

155

171

190

8.6

12.3

FR1931

FRC613

FRC614

1

C0750A2F

C1000A2F

C1500A2F

2000

3000

5000

5-7/8

6-1/2

7-5/8

6-7/8

8-3/16

8-15/16

8-1/2

8-3/4

10-1/4

36

52

79

149

165

193

174

207

227

215

222

260

16.3

23.6

35.8

FRC827

FRC828

FRC829

1

C2000A2F

C3000A2F

C5000A2F

230/460 Volts to 115/230 Volts, 60 Hz

50

75

100

2-19/32

3-3/16

3

3-3/4

3-1/4

3-3/4

4

2

3

4

65

80

76

95

82

95

102

.9

1.4

1.8

FR1310

FR1510

FR1512

3

C0050A2G

C0075A2G

C0100A2G

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4-3/4

4-1/2

5

6

7

8

80

96

95

114

95

114

127

2.7

3.2

3.6

FR1520

FR1714

FR1717

3

C0150A2G

C0200A2G

C0250A2G

300

350

500

3-13/16

4-3/8

4-1/2

5-1/4

6

6-1/4

10

12

15

96

111

114

133

152

158

4.5

5.4

6.8

FR1727

FR1930

3

C0300A2G

C0350A2G

C0500A2G

750

1000

1500

5-1/4

6

6-1/8

6-7/8

6-3/4

7-1/2

19

27

133

152

155

174

171

190

8.6

12.3

FRC613

FRC614

3

C0750A2G

C1000A2G

C1500A2G

2000

3000

5000

5-7/8

6-1/2

5-5/8

6-7/8

8-3/16

8-15/16

8-1/2

8-3/4

10-1/4

36

52

79

149

165

193

174

207

227

215

222

260

16.3

23.6

35.8

FRC827

FRC828

FRC829

3

C2000A2G

C3000A2G

C5000A2G

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-36

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTA

Table 44-43. Type MTA

See Page 44-34 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Frame Wiring

Diagram 

Style

Number

Price

U.S.

Height Width Depth Height Width Depth

230/460/575 Volts to 115/95 Volts, 50/60 Hz

50

75

100

2-19/32

3-3/16

3

3-3/4

4

4 3/4

2

4

5

98

80

76

95

102

120

1.5

1.8

2.7

FR1314

FR1512

FR1517

2A

C0050A3C

C0075A3C

C0100A3C

150

200

250

3-13/16

4-1/2

5

5-1/2

7

8

10

96

114

127

139

3.2

3.6

4.5

FR1714

FR1717

FR1723

2A

C0150A3C

C0200A3C

C0250A3C

300

350

500

3-13/16

4-3/8

4-1/2

5-1/4

6

5-5/8

6-1/8

12

14

17

96

111

114

133

152

143

155

5.4

6.8

8.6

FR1730

FR1923

FR1931

2A

C0300A3C

C0350A3C

C0500A3C

750

1000

1500

4-3/8

6

5-7/8

5-1/4

6-7/8

7-3/4

7-1/2

8-1/2

27

24

34

111

152

149

133

174

196

190

215

12.3

10.9

15.4

FR1943

FRC614

FRC827

2A

C0750A3C

C1000A3C

C1500A3C

115 Volts to 24 Volts, 50/60 Hz

50

100

200

2-19/32

3-3/16

3-13/16

3

3-3/4

4-1/2

3-3/4

4-1/8

4-1/2

2

5

7

65

80

96

76

95

114

82

104

114

.9

2.3

3.2

FR1310

FR1513

FR1714

4B

C0050A3B

C0100A3B

C0200A3B

208/380/416 Volts to 115/95 Volts, 50/60 Hz

50

100

150

200

2-19/32

3-3/16

3-13/16

3

3-3/4

4-1/2

3-3/4

4-3/4

4-1/2

5

3

5

7

8

98

80

96

76

95

114

95

120

114

127

1.5

2.3

3.2

3.6

FR1314

FR1516

FR1714

FR1717

2B

C0050A3D

C0100A3D

C0150A3D

C0200A3D

250

300

500

3-13/16

4-3/8

4-1/2

5-1/4

5-1/2

6

6-1/8

10

13

18

96

111

114

133

139

152

155

4.5

5.4

8.6

FR1723

FR1730

FR1931

2B

C0250A3D

C0300A3D

C0500A3D

750

1000

1500

4-3/8

6

5-7/8

5-1/4

6-7/8

7-3/4

7-1/2

8-1/2

27

25

33

111

152

149

133

174

196

190

215

12.3

10.9

15.4

FR1943

FRC614

FRC827

2B

C0750A3D

C1000A3D

C1500A3D

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-37

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTC

Type MTC Transformers

Product Description

■Varnish impregnated core and

coil design.

■Suitable for indoor applications.

Application Description

Transformers provide stepped down

voltages to machine tool control

devices enabling control circuits to be

isolated from all power and lighting

circuits. This allows the use of

grounded or ungrounded circuits that

are independent of the power or light-

ing grounds; greater safety is afforded

the operator. The control transformer

line is particularly adaptable on appli-

cations where compact construction

is demanded. The MTC line is similar

to the MTA line except it provides

increased regulation.

Features, Beneﬁts

and Functions

■Designed speciﬁcally for loads

requiring extremely good regulation

— 10% – 200% better regulation

than Type MTA.

■UL recognized component for units

rated 1000 VA and below.

■CSA certiﬁed for units rated 1000 VA

and below.

■50/60 Hz operation standard.

■100% tested to verify product quality.

■Each unit must pass rigid tests for

turns ratio, insulation, continuity,

and over potential.

■Performance equals or exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

■50 – 5000 VA ratings.

■55ºC rise, 105ºC insulation system.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribu-

tion and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI and IEEE Standards.

Product Speciﬁcations

Frequency

Cutler-Hammer standard dry-type dis-

tribution transformers are designed

for 60 Hz operation. Transformers

required for other frequencies are

available and must be speciﬁcally

designed.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-44. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Series-Multiple Windings

Series-multiple windings consist of 2

similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series), or 240

with a 120 mid-point.

The following pages provide listings for most

standard transformer ratings and styles.

For other ratings or styles not shown, refer

to Eaton.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

April 2009

44-38

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTC

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-45. Type MTC

See Page 44-34 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

Table 44-46. Type MTC with Integrally Mounted 30 Amperes, 600 volt Class with 2-Pole Primary Fuse Block for Rejection Type Fuses

(Fuses Not Included)

See Page 44-34 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Frame Wiring

Diagram 

Style

Number

Price

U.S.

Height Width Depth Height Width Depth

240/480 Volts to 120 Volts, 60 Hz

230/460 Volts to 115 Volts, 50/60 Hz

220/440 Volts to 110 Volts, 50/60 Hz

50

75

100

2-19/32

2-7/8

3

3-3/8

3-3/4

4

2

3

66

73

76

86

95

102

.9

1.4

FR1310

FR1314

FR1413

1

C0050C2A

C0075C2A

C0100C2A

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4-3/4

4-1/2

5

6

7

8

81

97

95

114

121

114

127

2.7

3.2

3.6

FR1517

FR1714

FR1717

1

C0150C2A

C0200C2A

C0250C2A

300

350

500

3-13/16

4-3/8

4-1/2

5-1/4

5-3/8

6

6-1/8

10

11

20

97

111

114

133

137

152

156

4.5

5.0

9.1

FR1722

FR1726

FR1931

1

C0300C2A

C0350C2A

C0500C2A

750

1000

1500

4-3/8

5-7/16

6-1/8

5-1/4

6-3/8

6-7/8

7-3/4

7-1/2

8-3/8

28

34

35

111

138

156

133

162

175

197

191

213

12.7

15.4

15.9

FR1934

FR2236

FRC822

1

C0750C2A

C1000C2A

C1500C2A

2000

3000

5000

6

7-3/8

7-7/8

6-3/4

8-7/16

8-11/16

8-1/2

8-3/4

11

38

53

82

152

187

200

171

214

221

216

222

279

17.3

24.1

37.2

FRC823

FRC824

FRC825

1

C2000C2A

C3000C2A

C5000C2A

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Frame Wiring

Diagram 

Style

Number

Price

U.S.

Height Width Depth Height Width Depth

240/480 Volts to 120 Volts, 60 Hz

230/460 Volts to 115 Volts, 50/60 Hz

220/440 Volts to 110 Volts, 50/60 Hz

50

75

100

150

3-7/8

4-5/32

4-15/32

3

3-3/8

3-3/4

4

4-3/4

2.2

3.2

6.2

98

106

114

76

86

95

83

95

102

121

1.0

1.5

2.8

FR1310

FR1314

FR1413

FR1517

1

C0050C2AFB

C0075C2AFB

C0100C2AFB

C0150C2AFB

200

250

300

5-3/32

4-1/2

5

5-3/8

7.2

8.2

10.2

129

114

127

137

3.3

3.7

4.7

FR1714

FR1717

FR1722

1

C0200C2AFB

C0250C2AFB

C0300C2AFB

350

500

750

5-3/32

5-21/32

4-1/2

5-1/4

6

6-1/8

7-3/4

11.2

20.2

28.2

129

144

114

133

152

156

197

5.1

9.2

12.8

FR1726

FR1931

FR1934

1

C0350C2AFB

C0500C2AFB

C0750C2AFB

1000

1500

2000

6-23/32

7-13/32

7-9/32

6-3/8

6-7/8

6-3/4

7-1/2

8-3/8

8-1/2

34.2

35.2

38.2

171

188

185

162

175

171

191

213

216

15.5

16.0

17.4

FR2236

FRC822

FRC823

1

C1000C2AFB

C1500C2AFB

C2000C2AFB

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-39

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Type MTE Transformers

Product Description

■Epoxy-encapsulated coils.

Application Description

Transformers provide stepped down

voltages to machine tool control

devices enabling control circuits to be

isolated from all power and lighting

circuits. This allows the use of

grounded or ungrounded circuits that

are independent of the power or light-

ing grounds; greater safety is afforded

the operator. The control transformer

line is particularly adaptable on appli-

cations where compact construction

is demanded.

Note: The MTG, “open core-coil design”

has been superseded by the epoxy-

encapsulated core-coil design MTE with

no change to dimensions or functionality.

Features, Beneﬁts

and Functions

■UL listed.

■CSA certiﬁed.

■Epoxy encapsulated.

■Laminations of high quality silicon

steel to minimize core losses and

optimize performance.

■Copper magnet wire for high

quality, efﬁcient operation.

■Secondary fuse clips where

applicable.

■Optional primary fusing.

■Molded in terminals.

■50/60 Hz operation.

■55°C rise, 105ºC insulation system.

■Performance meets/exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

■25 – 1500 VA ratings.

■Molded-in terminals for maximum

durability.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribution

and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI, and IEEE Standards. All 600 volt

class transformers are UL listed unless

otherwise noted.

Options and Accessories

Primary Fuse Kit

The primary fuse kit includes a 2-pole

class CC fuse block, instructions, and

all associated mounting and wiring

hardware. Fuses are not included.

When installed, the primary fuse kit

will add a maximum of 11/16 inch to

the transformer depth and 1-15/16

inches to the transformer height.

Table 44-47. Primary Fuse Kit

Note: 1000 VA and larger are Class 130°C

Insulation System.

Finger-Safe Terminal Covers (Optional)

■Fits CE marked designs 50 – 750 VA.

■Fits MTE designs 25 – 750 VA.

Table 44-48. Finger-Safe Terminal Covers

Finger-Safe Terminal Covers — FSK4

Finger-Safe Terminal Covers — FSK6

Finger-Safe Primary Fuse Block Covers

■Fits 2-pole primary fuse blocks on

MTE designs.

Table 44-49. Finger-Safe Primary Fuse

Block Covers

Finger-Safe Primary Fuse Block Covers

Description Catalog

Number

Price

U.S. $

Primary Fuse Kit PFK1

Description Catalog

Number

Price

U.S. $

4 Terminal Transformers

6 Terminal Transformers

FSK4

FSK6

Description Catalog

Number

Price

U.S. $

Primary Fuse Block Covers FSKFB

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-40

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Product Speciﬁcations

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-50. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Series-Multiple Windings

Series-multiple windings consist of

2 similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series),

or 240 with a 120 mid-point.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

Wiring Diagrams

Figure 44-7. Diagram 1

Figure 44-8. Diagram 2

Figure 44-9. Diagram 3

Figure 44-10. Diagram 4

Figure 44-11. Diagram 5

Figure 44-12. Diagram 6

April 2009

CA08102001E For more information visit: www.eaton.com

44-41

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Wiring Diagrams

Figure 44-13. Diagram 7

Figure 44-14. Diagram 8

Figure 44-15. Diagram 9

Figure 44-16. Diagram 10

Figure 44-17. Diagram 11

Figure 44-18. Diagram 12

Figure 44-19. Diagram 13

Figure 44-20. Diagram 14

Figure 44-21. Diagram 15

Figure 44-22. Diagram 16

H1

H

3

H2

H4

H1

H

3

H2

H4

H1

H

3

H2

H4

X4

X2

X

3

X1

X4

X2

X

3

X1

X4

X2

X

3

X1

24

0

V

480 V

240 V

12

0

V

H1

H2

X2

X1

600

V

5

7

5

V

550

V

24 V

2

3

V

22 V

H1

H2

X2

X1

42

0

V

4

00

V

380

V

24 V

2

3

V

22 V

H1

H2

H

3

H4

H

5

X

3

X2

X1

5

50

,

575

,

600 V

4

40

,

460

,

480 V

380

,

400

,

416 V

2

20

,

230

,

240 V

2

3

/

24

/

25

1

10

,

115

,

120

V

0

V

0

V

X4

X

3

X2

X1

H1

H2

H

3

H4

H

5

H

6

5

7

5

V

460

V

400

V

230

V

208

V

0

V

0

V

24 V

1

5

V

230

V

X4

X

3

X2

X1

H1

H2

H

3

H4

H

5

H

6

5

7

5

V

460

V

400

V

230

V

208

V

0

V

0

V

0

V

1

5

V

1

5

V

April 2009

44-42

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-51. Type MTE — Product Selection

See Page 44-40 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480, 230 x 460, 220 x 440 with Jumpers

Secondary: 120/115/110 with Fuse Clips for 13/32 x 1-1/2 Fuses

25

50

75

100

2-9/16

2-7/8

3

3-3/8

2-1/2

3

3-1/2

3-3/8

1.7

2.6

3.5

4.2

65

73

76

86

64

76

89

86

.8

1.2

1.6

1.9

1

C0025E2A

C0050E2A

C0075E2A

C0100E2A

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4

4-3/8

6.7

8.5

10.0

81

97

95

114

102

111

3.0

3.9

4.5

1

C0150E2A

C0200E2A

C0250E2A

300

350

500

3-13/16

4-3/4

4-1/2

5-1/4

4-3/4

5-1/4

5-1/2

11.3

13.6

19.2

97

121

114

133

121

133

140

5.1

6.2

8.7

1

C0300E2A

C0350E2A

C0500E2A

750

1000

1500

4-3/4

5-11/16

6-3/8

5-1/4

6-3/4

7-1/2

7

6-7/16

7-3/8

28.1

29.5

40.0

121

144

162

133

171

191

178

164

187

12.8

13.4

18.1

1

C0750E2A

C1000E2A

C1500E2A

Primary: 240 x 480 with Jumpers

Secondary: 24 with Fuse Clips for 13/32 x 1-1/2 Fuses (through 500 VA)

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-1/2

3-3/8

4

2.7

3.5

4.2

6.7

65

73

81

76

86

95

76

89

86

102

1.2

1.6

1.9

3.0

2

C0050E2B

C0075E2B

C0100E2B

C0150E2B

200

250

300

3-13/16

4-1/2

4

4-3/8

4-3/4

8.5

10.1

11.4

97

114

102

111

121

3.9

4.6

5.2

2

C0200E2B

C0250E2B

C0300E2B

350

500

750

3-13/16

4-3/4

4-1/2

5-1/4

5-5/8

7

13.4

17.5

28.1

97

121

114

133

143

178

6.1

7.9

12.8

2

C0350E2B

C0500E2B

C0750E2B

Primary: 120 x 240 with Jumpers

Secondary: 24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

2-9/16

2-7/8

3

3-3/8

3

3-1/2

3-3/8

2.6

3.6

4.4

65

73

76

86

76

89

56

1.2

1.6

2.0

3

C0050E1B

C0075E1B

C0100E1B

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4

4-3/8

6.7

8.3

10.1

81

97

95

114

102

111

3.0

3.8

4.6

3

C0150E1B

C0200E1B

C0250E1B

300

350

500

3-13/16

4-3/4

4-1/2

5-1/4

4-3/4

5-1/4

5-5/8

11.2

13.2

17.5

97

121

114

133

121

133

143

5.1

6.0

7.9

3

C0300E1B

C0350E1B

C0500E1B

Primary: 208/277

Secondary: 120 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-1/2

3-3/8

4

2.9

3.8

4.5

6.9

65

73

81

76

86

95

76

89

86

102

1.3

1.7

2.0

3.1

4

C0050E3A

C0075E3A

C0100E3A

C0150E3A

200

250

300

3-13/16

4-1/2

4

4-3/8

4-3/4

8.7

10.2

11.4

97

114

102

111

121

3.9

4.6

5.2

4

C0200E3A

C0250E3A

C0300E3A

350

500

750

3-13/16

4-3/4

4-1/2

5-1/4

5-3/8

7

13.7

17.2

25.7

97

121

114

133

136

178

6.2

7.8

11.7

4

C0350E3A

C0500E3A

C0750E3A

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-43

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Table 44-52. Type MTE — Product Selection

See Page 44-41 for Wiring Diagrams.

Secondary fuse clips are not available on this catalog number.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480 with Jumpers

Secondary: 120 x 240 with Jumpers, Secondary Fuse Clips not Applicable

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-1/2

3-3/8

4

2.6

3.5

4.2

6.7

65

73

81

76

86

95

76

89

86

102

1.2

1.6

1.9

3.1

11

C0050E2CXX

C0075E2CXX

C0100E2CXX

C0150E2CXX

200

250

300

3-13/16

4-1/2

4

4-3/8

4-7/8

8.5

10.0

11.8

97

114

102

111

124

3.9

4.6

5.4

11

C0200E2CXX

C0250E2CXX

C0300E2CXX

350

500

750

3-13/16

4-3/4

4-1/2

5-1/4

7

13.6

17.5

26.4

97

121

114

133

178

6.2

8.0

12.0

11

C0350E2CXX

C0500E2CXX

C0750E2CXX

Primary: 550/575/600

Secondary: 110/115/120 with for 13/32 x 1-1/2 Fuses

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-1/2

3-3/8

4

2.7

3.6

4.2

6.8

65

73

81

76

86

95

76

89

86

102

1.2

1.6

1.9

3.1

10

C0050E4C

C0075E4C

C0100E4C

C0150E4C

200

250

300

3-13/16

4-1/2

4

4-3/8

4-3/4

8.4

10.0

11.3

97

114

102

111

121

3.8

4.6

5.1

10

C0200E4C

C0250E4C

C0300E4C

350

500

750

3-13/16

4-3/4

4-1/2

5-1/4

5-3/8

7

13.6

16.8

25.7

97

121

114

133

137

178

6.2

7.6

11.7

10

C0350E4C

C0500E4C

C0750E4C

Primary: 380/400/415

Secondary: 22/23/24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

2-9/16

2-7/8

3

3-3/8

3

3-1/2

3-3/8

2.5

3.5

4.0

65

73

76

86

76

89

86

1.1

1.6

1.8

13

C0050E4H

C0075E4H

C0100E4H

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4

4-3/8

6.5

8.2

10.0

81

97

95

114

102

111

3.0

3.7

4.5

13

C0150E4H

C0200E4H

C0250E4H

300

350

500

3-13/16

4-3/4

4-1/2

5-1/4

4-3/4

5-1/4

5-1/2

11.0

13.6

17.7

97

121

114

133

121

133

140

5.0

6.2

8.0

13

C0300E4H

C0350E4H

C0500E4H

Primary: 550/575/600

Secondary: 22/23/24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-1/2

3 3/8

4

2.5

3.5

4.0

6.5

65

73

81

76

86

95

76

89

86

102

1.1

1.6

1.8

3.0

12

C0050E4W

C0075E4W

C0100E4W

C0150E4W

200

250

300

3-13/16

4-1/2

4

4-3/8

4-3/4

8.2

10.0

11.0

97

114

102

111

121

3.7

4.5

5.0

12

C0200E4W

C0250E4W

C0300E4W

350

500

750

3-13/16

4-3/4

4-1/2

5-1/4

5-1/2

7-3//8

13.6

17.7

28.0

97

121

114

133

140

187

6.2

8.0

12.7

12

C0350E4W

C0500E4W

C0750E4WXX 

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-44

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Table 44-53. Types MTE — Product Selection

See Pages 44-40 and 44-41 for Wiring Diagrams.

Type MTG Open Core-Coil Universal Design has been superseded by Type MTE Epoxy Encapsulated Universal Design with no changes to form,

ﬁt or function.

Type MTE Epoxy Encapsulated Universal Design.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 230/460/575

Secondary: 115/95 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-3/8

3-7/8

4-1/4

3.5

4.5

6.0

7.7

65

73

81

76

86

95

76

86

98

108

1.6

2.0

2.7

3.5

5

C0050E3C

C0075E3C

C0100E3C

C0150E3C

200

250

300

3-13/16

4-1/2

4-1/4

4-3/4

5-1/8

9.0

9.7

11.7

97

114

108

121

130

4.1

4.4

5.3

5

C0200E3C

C0250E3C

C0300E3C

350

500

750

4-3/4

5-1/4

5

5-5/8

7

16.5

21.5

28.0

121

133

127

143

178

7.5

9.8

12.7

5

C0350E3C

C0500E3C

C0750E3C

Primary: 380/400/415

Secondary: 110 x 220 with Jumpers; Fuse Clips not Applicable

50

75

100

150

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3

3-1/2

3-9/16

4

3.0

4.0

5.2

7.0

65

73

81

76

86

95

76

89

90

102

1.4

1.8

2.4

3.2

6

C0050E4D

C0075E4D

C0100E4D

C0150E4D

200

250

300

3-13/16

4-1/2

4

4-3/8

4-3/4

8.7

10.2

11.0

97

114

102

111

121

3.9

4.6

5.0

6

C0200E4D

C0250E4D

C0300E4D

350

500

750

3-13/16

4-3/4

4-1/2

5-1/4

5-3/8

7

13.0

20.0

28.0

97

121

114

133

136

178

5.9

9.1

12.7

6

C0350E4D

C0500E4D

C0750E4D

Primary: 200/220/440, 208/230/460, 240/480

Secondary: 23/110, 24/115, 25/120 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

2-9/16

2-7/8

3-3/16

3

3-3/8

3-3/4

3-1/4

3-1/2

5-5/8

3.4

4.8

5.9

65

73

81

76

86

95

83

89

143

1.5

2.2

2.7

7

C0050E5E

C0075E5E

C0100E5E

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4-3/8

4-1/2

5-1/4

7.9

10.6

13.9

81

97

95

114

111

114

133

3.6

4.8

6.3

7

C0150E5E

C0200E5E

C0250E5E

300

350

500

4-3/4

5-1/4

5-1/8

5-3/8

6-7/8

15.5

16.8

23.4

121

133

130

136

175

7.0

7.6

10.6

7

C0300E5E

C0350E5E

C0500E5E

Universal Design (MTE Epoxy Encapsulated)

Primary: 240/416/480/600, 230/400/460/575, 220/380/440/550, 208/500

Secondary: 99/120/130, 95/115/125, 91/110/120, 85/100/110 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

100

150

250

2-7/8

3-3/16

3-13/16

3-3/8

3-3/4

4-1/2

4

4-5/8

4-7/16

5-7/8

4.0

6.6

8.8

14.7

73

81

97

86

95

114

102

117

113

149

1.8

3.0

4.0

6.7

8

C0050E6U 

C0100E6U 

C0150E6U 

C0250E6U 

350

500

750

4-7/16

5-3/4

5-1/4

6-3/4

5-5/8

7

5-11/16

18.6

25.6

30.5

113

146

133

171

143

178

144

8.4

11.6

13.8

8

C0350E6U 

C0500E6U 

C0750E6U 

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-45

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Table 44-54. Transformers with Primary Fuse Blocks — Product Selection

See Page 44-40 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480, 230 x 460, 220 x 440 with Jumpers and Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 120/115/110 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

3-15/16

4-1/4

3

3-3/8

3

3-1/2

3-3/8

2.8

3.7

4.4

100

108

76

86

76

89

86

1.3

1.7

2.0

1

C0050E2AFB

C0075E2AFB

C0100E2AFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4

4-3/8

6.9

8.7

10.2

116

132

95

114

102

111

3.1

3.9

4.6

1

C0150E2AFB

C0200E2AFB

C0250E2AFB

300

350

500

5-3/16

6-1/8

4-1/2

5-1/4

4-3/4

5-1/4

5-1/2

11.5

13.8

19.4

132

156

114

133

121

133

140

5.2

6.3

8.8

1

C0300E2AFB

C0350E2AFB

C0500E2AFB

750

1000

1500

6-1/8

7-1/16

7-3/4

5-1/4

6-3/4

7-1/2

7

6-7/16

7-3/8

28.3

29.7

40.2

156

179

197

133

171

191

178

164

187

12.8

13.4

18.1

1

C0750E2AFB

C1000E2AFB

C1500E2AFB

Primary: 240 x 480 with Jumpers and Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

3-15/16

4-1/4

3

3-3/8

3

3-1/2

3-3/8

2.8

3.8

4.4

100

108

76

86

76

89

86

1.3

1.7

2.1

2

C0050E2BFB

C0075E2BFB

C0100E2BFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4

4-3/8

6.9

8.7

10.3

116

132

95

114

102

111

3.1

3.9

4.7

2

C0150E2BFB

C0200E2BFB

C0250E2BFB

300

350

500

5-3/16

6-1/8

4-1/2

5-1/4

4-3/4

5-1/4

5-5/8

11.6

13.6

17.7

132

156

114

133

121

133

143

5.3

6.2

8.0

2

C0300E2BFB

C0350E2BFB

C0500E2BFB

Primary: 120 x 240 with Jumpers and Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

3-15/16

4-1/4

3

3-3/8

3

3 1/2

3 3/8

2.8

3.8

4.6

100

108

76

86

76

89

86

1.3

1.7

2.1

3

C0050E1BFB

C0075E1BFB

C0100E1BFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4

4 3/8

6.9

8.5

10.3

116

132

95

114

102

111

3.1

3.9

4.7

3

C0150E1BFB

C0200E1BFB

C0250E1BFB

300

350

500

5-3/16

6-1/8

4-1/2

5-1/4

4 3/4

5 1/4

5 5/8

11.4

13.4

17.7

132

156

114

133

121

133

143

5.2

6.1

8.0

3

C0300E1BFB

C0350E1BFB

C0500E1BFB

Primary: 208/277 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 120 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

3-15/16

4-1/4

3

3-3/8

3

3-1/2

3-3/8

3.1

4.0

4.7

100

108

76

86

76

89

86

1.4

1.8

2.1

4

C0050E3AFB

C0075E3AFB

C0100E3AFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4

4-3/8

7.1

8.9

10.4

116

132

95

114

102

111

3.2

4.0

4.7

4

C0150E3AFB

C0200E3AFB

C0250E3AFB

300

350

500

5-3/16

6-1/8

4-1/2

5-1/4

4-3/4

5-1/4

5-3/8

11.6

13.9

17.4

132

156

114

133

121

133

143

5.3

6.3

7.9

4

C0300E3AFB

C0350E3AFB

C0500E3AFB

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-46

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Table 44-55. Transformers with Primary Fuse Blocks — Product Selection

See Page 44-41 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 550/575/600 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 110/115/120 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

150

3-15/16

4-1/4

4-9/16

3

3 -3/8

3-3/4

3

3-1/2

3 3/8

4

2.9

3.8

4.4

7.0

100

108

116

76

86

95

76

89

86

102

1.3

1.7

2.0

3.2

10

C0050E4CFB

C0075E4CFB

C0100E4CFB

C0150E4CFB

200

250

300

5-3/16

4-1/2

4

4 3/8

4 3/4

8.6

10.2

11.5

132

114

102

111

121

3.9

4.6

5.2

10

C0200E4CFB

C0250E4CFB

C0300E4CFB

350

500

750

5-3/16

6-1/8

4-1/2

5-1/4

5 1/4

5 3/8

7

13.8

17.0

25.9

132

156

114

133

137

178

6.3

7.7

11.8

10

C0350E4CFB

C0500E4CFB

C0750E4CFB

Primary: 380/400/415 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 22/23/24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

2-9/16

2-7/8

3

3-3/8

3

3-1/2

3-3/8

2.6

3.7

4.2

65

73

76

86

76

89

86

1.2

1.7

1.9

13

C0050E4HFB

C0075E4HFB

C0100E4HFB

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4

4-3/8

6.7

8.4

10.2

81

97

95

114

102

111

3.0

3.8

4.6

13

C0150E4HFB

C0200E4HFB

C0250E4HFB

Primary: 550/575/600 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 22/23/24 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

2-9/16

2-7/8

3

3-3/8

3

3-1/2

3-3/8

2.7

3.7

4.2

65

73

76

86

76

89

86

1.2

1.7

1.9

12

C0050E4WFB

C0075E4WFB

C0100E4WFB

150

200

250

3-3/16

3-13/16

3-3/4

4-1/2

4

4-3/8

6.7

8.4

10.2

81

97

95

114

102

111

3.0

3.8

4.6

12

C0150E4WFB

C0200E4WFB

C0250E4WFB

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-47

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTE

Table 44-56. Transformers with Primary Fuse Blocks — Product Selection

See Pages 44-40 and 44-41 for Wiring Diagrams.

Type MTG Open Core-Coil Universal Design has been superseded by Type MTE Epoxy Encapsulated Universal Design with no changes to form,

ﬁt or function.

Type MTE Epoxy Encapsulated Universal Design.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 230/460/575 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 115/95 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

3-13/16

4-1/4

3

3-3/8

3

3-3/8

3-7/8

3.7

4.7

6.2

97

108

76

86

76

86

98

1.7

2.1

2.8

5

C0050E3CFB

C0075E3CFB

C0100E3CFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4-1/4

4-3/4

7.9

9.2

9.9

116

132

95

114

108

121

3.6

4.2

4.5

5

C0150E3CFB

C0200E3CFB

C0250E3CFB

300

350

500

5-3/16

6-1/8

4-1/2

5-1/4

5-1/8

5

5-7/8

11.9

16.7

21.7

132

156

114

133

130

127

149

5.4

7.6

9.9

5

C0300E3CFB

C0350E3CFB

C0500E3CFB

Primary: 380/400/415 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 110 x 220 with Jumpers; Fuse Clips Not Available

50

75

100

3-15/16

4-1/4

3

3-3/8

3

3-1/2

3-9/16

3.2

4.2

5.4

100

108

76

86

76

89

90

1.5

1.9

2.5

6

C0050E4DFB

C0075E4DFB

C0100E4DFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4

4-3/8

7.2

8.9

10.4

116

132

95

114

102

111

3.3

4.0

4.7

6

C0150E4DFB

C0200E4DFB

C0250E4DFB

300

350

500

5-3/16

6-1/8

4-1/2

5-1/4

4-3/4

5-1/4

5-5/8

11.2

13.2

20.2

132

156

114

133

121

133

143

5.1

6.0

9.2

6

C0300E4DFB

C0350E4DFB

C0500E4DFB

Primary: 200/220/440, 208/230/460, 240/480 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 23/110, 24/115, 25/120 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

75

100

3-15/16

4-1/4

4-9/16

3

3-3/8

3-3/4

3-1/4

3-1/2

3-5/8

3.6

5.0

6.1

100

108

116

76

86

95

83

89

92

1.6

2.3

2.8

7

C0050E5EFB

C0075E5EFB

C0100E5EFB

150

200

250

4-9/16

5-3/16

3-3/4

4-1/2

4-3/8

4-1/2

5-1/4

8.1

10.8

14.1

116

132

95

114

111

114

133

3.7

4.9

6.4

7

C0150E5EFB

C0200E5EFB

C0250E5EFB

300

350

500

6-1/8

5-1/4

5-1/8

5-3/8

6-7/8

15.7

17.0

23.6

156

133

130

136

175

7.1

7.7

10.7

7

C0300E5EFB

C0350E5EFB

C0500E5EFB

Universal Design (MTE Epoxy Encapsulated)

Primary: 240/416/480/600, 230/400/460/575, 220/380/440/550, 208/500 with Two-Pole Primary Fuse Block for Rejection Type Fuses

Secondary: 99/120/130, 95/115/125, 91/110/120, 85/100/110 with Fuse Clips for 13/32 x 1-1/2 Fuses

50

100

150

4-1/4

4-9/16

5-3/16

3-3/8

3-3/4

4-1/2

4

4-5/8

4-7/16

4.2

6.8

9.0

108

116

132

86

95

114

102

117

113

1.9

3.1

4.1

8

C0050E6UFB 

C0100E6UFB 

C0150E6UFB 

250

350

500

5-3/16

5-13/16

4-1/2

5-1/4

5-7/8

5-5/8

7

14.9

18.8

25.8

132

148

114

133

149

143

178

6.8

8.5

11.7

8

C0250E6UFB 

C0350E6UFB 

C0500E6UFB 

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-48

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTK

Type MTK Transformers

Product Description

■Epoxy resin-impregnated coil.

■Economical solution for high

inrush applications.

Application Description

Transformers provide stepped down

voltages to machine tool control

devices enabling control circuits to be

isolated from all power and lighting

circuits. This allows the use of

grounded or ungrounded circuits that

are independent of the power or light-

ing grounds; greater safety is afforded

the operator. The control transformer

line is particularly adaptable on appli-

cations where compact construction

is demanded.

Features, Beneﬁts

and Functions

■UL listed.

■CSA certiﬁed.

■Epoxy resin impregnated coil design.

■Copper magnet wire for high

quality, efﬁcient operation.

■50/60 Hz operation.

■115°C rise, 180ºC insulation system.

■Performance meets/exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

■500 – 5000 VA ratings.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribution

and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI, and IEEE Standards. All 600 volt

class transformers are UL listed unless

otherwise noted.

Product Speciﬁcations

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-57. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Series-Multiple Windings

Series-multiple windings consist of 2

similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series), or 240

with a 120 mid-point.

The following pages provide listings for most

standard transformer ratings and styles.

For other ratings or styles not shown, refer

to Eaton.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

April 2009

CA08102001E For more information visit: www.eaton.com

44-49

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTK

Wiring Diagrams

Figure 44-23. Diagram 1

Figure 44-24. Diagram 2

Figure 44-25. Diagram 3

Figure 44-26. Diagram 4

Figure 44-27. Diagram 5

Figure 44-28. Diagram 6

Figure 44-29. Diagram 7

Figure 44-30. Diagram 8

Figure 44-31. Diagram 9

Figure 44-32. Diagram 10

Figure 44-33. Diagram 11

H1

H

3

H2

H4

H1

H

3

H2

H4

H1

H

3

H2

H4

X4

X2

X

3

X1

X4

X2

X

3

X1

X4

X2

X

3

X1

24

0

V

480 V

240 V

12

0

V

April 2009

44-50

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTK

Wiring Diagrams

Figure 44-34. Diagram 12

Figure 44-35. Diagram 13

Figure 44-36. Diagram 14

Figure 44-37. Diagram 15

Figure 44-38. Diagram 16

H1

H2

X2

X1

600

V

5

7

5

V

550

V

24 V

2

3

V

22 V

H1

H2

X2

X1

42

0

V

4

00

V

380

V

24 V

2

3

V

22 V

H1

H2

H

3

H4

X

3

X2

X1

5

50

,

575

,

600 V

4

40

,

460

,

480 V

380

,

400

,

416 V

2

20

,

230

,

240 V

2

3

/

24

/

25

1

10

,

115

,

120

V

0

V

X4

X

3

X2

X1

H1

H2

H

3

H4

H

5

H

6

5

7

5

V

460

V

400

V

230

V

208

V

0

V

0

V

24 V

1

5

V

230

V

X4

X

3

X2

X1

H1

H2

H

3

H4

H

5

H

6

5

7

5

V

460

V

400

V

230

V

208

V

0

V

0

V

0

V

1

5

V

1

5

V

April 2009

CA08102001E For more information visit: www.eaton.com

44-51

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTK

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-58. Type MTK — Product Selection

See Page 44-49 and for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480, 230 x 460, 220 x 440

Secondary: 120/115/110

500

750

1000

1500

3-13/16

4-7/16

5-11/16

4-1/2

5-1/2

5-1/4

6-3/4

6

6-1/2

7-7/8

6-3/4

13.0

19.5

29.8

30.0

97

113

144

114

133

171

152

165

200

171

5.9

8.9

13.6

1

C0500K2A

C0750K2A

C1000K2A

C1500K2A

2000

3000

5000

5-11/16

7-9/16

6-3/4

9

7

7-1/2

7-3/4

38.0

53.0

89.0

144

192

171

229

178

191

197

17.3

24.1

40.5

1

C2000K2A

C3000K2A

C5000K2A

Primary: 208/277

Secondary: 120

1000

1500

2000

5-3/8

5-11/16

6-3/8

6-3/4

7-1/8

7-1/2

8-1/4

29.0

33.0

43.0

137

144

162

171

181

191

210

13.1

15.0

19.5

4

C1000K3A

C1500K3A

C2000K3A

3000

5000

7-5/8

10-3/16

9

8-1/4

10-1/2

64.0

102.0

194

259

229

210

267

29.0

46.3

4

C3000K3A

C5000K3A

Primary: 230/460/575

Secondary: 115/95

1000

1500

2000

5-3/8

5-11/16

7-9/16

6-3/8

6-3/4

9

7-1/8

8-1/4

7-9/16

29.2

33.5

42.5

137

144

192

162

171

229

184

210

192

13.3

15.2

19.3

5

C1000K3C

C1500K3C

C2000K3C

3000

5000

7-9/16

7-3/16

9

8-5/8

13-1/2

63.7

102.0

192

259

229

219

343

29.0

46.4

5

C3000K3C

C5000K3C

Primary: 208/380/416

Secondary: 115/95

1000

1500

2000

5-3/8

5-11/16

6-3/8

6-3/4

7-1/8

8-1/4

9-1/4

29.0

43.0

55.0

137

144

162

171

181

210

235

13.1

19.5

25.0

9

C1000K3D

C1500K3D

C2000K3D

3000

5000

7-5/8

10-3/16

9

8-5/8

11

74.0

108.0

194

259

229

219

279

33.5

49.0

9

C3000K3D

C5000K3D

Primary: 550/575/600

Secondary: 110/115/120

1000

1500

2000

5-3/8

5-11/16

6-3/8

6-3/4

7-1/8

7-1/2

8-1/4

29.0

33.0

43.0

137

144

162

171

181

191

210

13.1

15.0

19.5

10

C1000K4C

C1500K4C

C2000K4C

3000

5000

7-5/8

10-3/16

9

8-1/4

10-1/2

64.0

102.0

194

259

229

210

267

29.0

46.3

10

C3000K4C

C5000K4C

Primary: 380/400/415

Secondary: 110 x 220

1000

1500

2000

5-11/16

6-3/4

6-1/2

7-1/2

8-1/4

28.0

33.0

43.0

144

171

165

191

210

12.7

15.0

19.5

6

C1000K4D

C1500K4D

C2000K4D

3000

5000

7-5/8

10-3/16

9

8-1/4

10-1/2

64.0

102.0

194

259

229

210

267

29.0

46.3

6

C3000K4D

C5000K4D

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-52

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type MTK

Table 44-59. Type MTK — Product Selection

See Page 44-49 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480 with Jumpers

Secondary: 120 x 240 with Jumpers, Secondary Fuse Clips Not Applicable

1000

1500

2000

4-7/16

5-11/16

5-3/4

5-1/4

6-3/4

7-7/8

7-1/4

8

26.4

31.0

40.0

113

144

146

133

171

200

184

203

12.0

14.1

18.2

11

C1000K2CXX

C1500K2CXX

C2000K2CXX

3000

5000

7-5/8

9

7-1/2

9-1/4

56.0

85.5

194

229

191

235

25.5

28.9

11

C3000K2CXX

C5000K2CXX

Primary: 120 x 240 with Jumpers

Secondary: 24

750

1000

4-1/2

5-1/4

6-3/4

8-3/4

19.0

26.4

114

133

171

222

8.6

12.0

3

C0750K1B

C1000K1B

Primary: 240/416/480/600, 230/400/460/575, 220/380/440/550, 208/500

Secondary: 99/120/130, 95/115/125, 91/110/120, 85/100/110

1000

1500

2000

5-3/4

6-3/4

6-1/2

7-7/8

9-3/16

26.5

38.5

52.0

146

171

165

200

233

12.0

17.5

23.6

8

C1000K6U

C1500K6U

C2000K6U

3000

5000

7-3/4

9-7/8

9

7-1/2

10-1/2

68.0

105.0

197

248

229

191

267

30.9

47.7

8

C3000K6U

C5000K6U

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-53

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Terminal Type A

Application Description

Transformers provide stepped down

voltages to machine tool control devices

enabling control circuits to be isolated

from all power and lighting circuits.

This allows the use of grounded or

ungrounded circuits that are indepen-

dent of the power or lighting grounds;

greater safety is afforded the operator.

The control transformer line is particu-

larly adaptable on applications where

compact construction is demanded.

Features, Beneﬁts

and Functions

Type MTE

■CE marked units comply with IEC

EN-61558-2.

■UL listed.

■CSA certiﬁed.

■Epoxy encapsulated coil design.

■Copper magnet wire for high

quality, efﬁcient operation.

■Laminations of high quality silicon

steel to minimize core losses and

optimize performance.

■Molded-in terminals.

■50/60 Hz operation.

■55°C rise, class 105 insulation.

■Performance meets/exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

■Non-short circuit proof transformer,

isolation type.

Type MTK

■CE marked units comply with IEC

EN-61558-2.

■UL listed.

■CSA certiﬁed.

■Epoxy resin-impregnated coil design.

■Copper magnet wire for high

quality, efﬁcient operation.

■50/60 Hz operation.

■115°C rise, 180°C insulation system.

■Performance meets/exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

■500 – 5000 VA ratings.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribution

and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI, and IEEE Standards. All 600 volt

class transformers are UL listed unless

otherwise noted.

Options and Accessories

Protection Index IP00

When terminal covers are installed on

primary and secondary, and fuse block

covers are used, the Protection Index

is IP20.

Finger-Safe Terminal Covers (Optional)

■Fits CE marked designs 50 – 750 VA.

■Fits MTE designs 25 – 750 VA.

Table 44-60. Finger-Safe Terminal Covers

Finger-Safe Terminal Covers — FSK4

Finger-Safe Terminal Covers — FSK6

Finger-Safe Primary Fuse Block Covers

■Fits 2-pole primary fuse blocks on

MTE designs.

Table 44-61. Finger-Safe Primary Fuse

Block Covers

Finger-Safe Primary Fuse Block Covers

Description Catalog

Number

Price

U.S. $

4 Terminal Transformers

6 Terminal Transformers

FSK4

FSK6

Description Catalog

Number

Price

U.S. $

Primary Fuse Block Covers FSKFB

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-54

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Product Speciﬁcations

Overload Capability

Short-term overload is designed into

transformers as required by ANSI.

Basically, dry-type distribution trans-

formers will deliver 200% nameplate

load for one-half hour; 150% load for

one-hour; and 125% load for four-hours

without being damaged provided that

a constant 50% load precedes and

follows the overload. See ANSI

C57.96-01.250 for additional limitations.

Continuous overload capacity is not

deliberately designed into a trans-

former because the design objective is

to be within the allowed winding tem-

perature rise with nameplate loading.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-62. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Series-Multiple Windings

Series-multiple windings consist of

2 similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series), or 240

with a 120 mid-point.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

Wiring Diagrams

Figure 44-39. Diagram 1

Figure 44-40. Diagram 2

Figure 44-41. Diagram 3

Figure 44-42. Diagram 4

Figure 44-43. Diagram 5

Figure 44-44. Diagram 6

April 2009

CA08102001E For more information visit: www.eaton.com

44-55

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Wiring Diagrams

Figure 44-45. Diagram 7

Figure 44-46. Diagram 8

Figure 44-47. Diagram 9

Figure 44-48. Diagram 10

Figure 44-49. Diagram 11

Figure 44-50. Diagram 12

Figure 44-51. Diagram 13

Figure 44-52. Diagram 14

Figure 44-53. Diagram 15

Figure 44-54. Diagram 16

H1

H

3

H2

H4

H1

H

3

H2

H4

H1

H

3

H2

H4

X4

X2

X

3

X1

X4

X2

X

3

X1

X4

X2

X

3

X1

24

0

V

480 V

240 V

12

0

V

H1

H2

X2

X1

600

V

5

7

5

V

550

V

24 V

2

3

V

22 V

H1

H2

X2

X1

42

0

V

4

00

V

380

V

24 V

2

3

V

22 V

H1

H2

H

3

H4

H

5

X

3

X2

X1

5

50

,

575

,

600 V

4

40

,

460

,

480 V

380

,

400

,

416 V

2

20

,

230

,

240 V

2

3

/

24

/

25

1

10

,

115

,

120

V

0

V

0

V

X4

X

3

X2

X1

H1

H2

H

3

H4

H

5

H

6

5

7

5

V

460

V

400

V

230

V

208

V

0

V

0

V

24 V

1

5

V

230

V

X4

X

3

X2

X1

H1

H2

H

3

H4

H

5

H

6

5

7

5

V

460

V

400

V

230

V

208

V

0

V

0

V

0

V

1

5

V

1

5

V

April 2009

44-56

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-63. Type MTE CE Marked IP00

See Pages 44-54 and 44-55 for Wiring Diagrams.

Note: Transformers are designed to operate in a maximum ambient of 40°C.

Note: Contact your local Eaton sales ofﬁce for availability on additional CE Marked control transformers.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480, 230 x 460, 220 x 440 with Jumpers

Secondary: 120/115/110

50

75

100

150

3

3-1/4

3-1/2

4

3

3-3/8

3-3/4

4-1/2

3-3/8

3-3/4

3.5

4.8

5.9

8.5

76

83

89

102

76

86

95

114

86

95

1.6

2.2

2.7

3.9

1

CE0050E2ACE

CE0075E2ACE

CE0100E2ACE

CE0150E2ACE

200

250

300

4

4-1/2

3-3/4

4

4-3/8

10.6

11.3

13.2

102

114

95

102

111

4.8

5.1

6.0

1

CE0200E2ACE

CE0250E2ACE

CE0300E2ACE

350

500

750

4-1/2

5-1/4

4-7/8

5-1/8

7

14.9

21.0

29.8

114

133

124

130

178

6.8

9.5

13.5

1

CE0350E2ACE

CE0500E2ACE

CE0750E2ACE

Primary: 240 x 480 with Jumpers

Secondary: 24

50

75

100

150

3

3-1/4

3-1/2

4

3

3-3/8

3-3/4

4-1/2

3-3/8

4

3.4

4.2

5.9

8.5

76

83

89

102

76

86

95

114

86

102

1.5

1.9

2.7

3.9

2

CE0050E2BCE

CE0075E2BCE

CE0100E2BCE

CE0150E2BCE

200

250

300

4

4-1/2

3-3/4

4

4-3/8

10.6

11.3

13.2

102

114

95

102

111

4.5

5.1

6.0

2

CE0200E2BCE

CE0250E2BCE

CE0300E2BCE

350

500

750

4-1/2

5

5-1/4

4-1/2

5-1/8

7

14.9

19.2

28.1

114

127

133

114

130

178

6.8

8.7

12.8

2

CE0350E2BCE

CE0500E2BCE

CE0750E2BCE

Primary: 120 x 240 with Jumpers

Secondary: 24

50

75

100

150

3

3-1/4

3-1/2

4

3

3-3/8

3-3/4

4-1/2

3-3/8

3-3/4

3.4

4.2

5.9

8.5

76

83

89

102

76

86

95

114

86

95

1.5

1.9

2.7

3.9

3

CE0050E1BCE

CE0075E1BCE

CE0100E1BCE

CE0150E1BCE

200

250

300

4

4-1/2

3-3/4

4

4-3/8

10.6

11.3

13.2

102

114

95

102

111

4.5

5.1

6.0

3

CE0200E1BCE

CE0250E1BCE

CE0300E1BCE

350

500

750

4-1/2

5-1/4

4-1/2

5-1/8

7

14.9

19.2

29.8

114

133

114

130

178

6.8

8.7

13.5

3

CE0350E1BCE

CE0500E1BCE

CE0750E1BCE

Primary: 550/575/600

Secondary: 110/115/120

50

75

100

150

3

3-1/4

3-1/2

4

3

3-3/8

3-3/4

4-1/2

3-3/8

3-3/4

3.5

4.8

5.9

8.5

76

83

89

102

76

86

95

114

86

95

1.6

2.2

2.7

3.9

10

CE0050E4CCE

CE0075E4CCE

CE0100E4CCE

CE0150E4CCE

200

250

300

4

4-1/2

3-3/4

4

4-3/8

10.6

11.3

13.2

102

114

95

102

111

4.8

5.1

6.0

10

CE0200E4CCE

CE0250E4CCE

CE0300E4CCE

350

500

750

4-1/2

5-1/4

4-1/2

5-1/8

7

14.9

21.0

29.8

114

133

114

130

178

6.8

9.5

13.5

10

CE0350E4CCE

CE0500E4CCE

CE0750E4CCE

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-57

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Table 44-64. Type MTE CE Marked IP00

See Pages 44-54 and 44-55 for Wiring Diagrams.

Note: Transformers are designed to operate in a maximum ambient of 40°C.

Note: Contact your local Eaton sales ofﬁce for availability on additional CE Marked control transformers.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 380/400/415

Secondary: 110 x 220 with Jumpers

50

75

100

150

3

3-1/2

4

3

3-3/8

3-3/4

4-1/2

3-3/8

3-3/4

3.5

4.8

5.9

8.5

76

89

102

76

86

95

114

86

95

1.6

2.2

2.7

3.9

6

CE0050E4DCE

CE0075E4DCE

CE0100E4DCE

CE0150E4DCE

200

250

300

4

4-1/2

3-3/4

4

4-3/8

10.6

11.3

13.2

102

114

95

102

111

4.8

5.1

6.0

6

CE0200E4DCE

CE0250E4DCE

CE0300E4DCE

350

500

750

4

4-1/2

5-1/4

4-3/4

5-1/8

7

15.2

21.0

29.8

102

114

133

121

130

178

6.9

9.5

13.5

6

CE0350E4DCE

CE0500E4DCE

CE0750E4DCE

Primary: 200/220/440, 208/230/460, 240/480

Secondary: 23/110, 24/115, 25/120

50

75

100

3-1/4

3-1/2

3-3/8

3-3/4

3-3/8

3-5/8

4.2

5.9

7.9

83

89

86

95

86

92

1.9

2.7

3.6

7

CE0050E5ECE

CE0075E5ECE

CE0100E5ECE

150

200

250

4

4-1/2

3-3/4

4-3/8

4-3/4

10.0

12.8

15.2

102

114

95

111

121

4.5

5.8

6.9

7

CE0150E5ECE

CE0200E5ECE

CE0250E5ECE

300

350

500

4-1/2

5-1/4

4-7/8

5-5/8

16.8

19.2

27.0

114

133

124

143

7.6

8.7

12.3

7

CE0300E5ECE

CE0350E5ECE

CE0500E5ECE

For other ratings or styles not shown, refer

to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-58

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Factory Mounted Finger-Safe Terminal Covers

Terminal Type A Terminal Type B Terminal Type C

Table 44-65. Type MTK CE Marked with Factory Mounted Finger-Safe Terminal Covers IP20

See Pages 44-54 and 44-55 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

Note: Contact your local Eaton sales ofﬁce for availability on additional CE Marked control transformers.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Terminal

Type

Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

Primary: 240 x 480, 230 x 460, 220 x 440 with Jumpers

Secondary: 120/115/110

250

300

350

500

4

4-1/2

4-5/16

4-7/8

5-3/16

5-5/8

8.8

11.0

11.2

14.8

102

114

110

124

132

143

4.0

5.0

5.1

6.7

A

1

CE0250K2ACEFS

CE0300K2ACEFS

CE0350K2ACEFS

CE0500K2ACEFS

750

1000

1500

4-1/2

5-1/2

6

5-1/4

6-3/8

6-3/4

5-15/16

6-5/8

7-5/16

18.0

26.3

40.0

114

140

152

133

162

172

151

168

186

8.2

11.9

18.1

A

C

1

CE0750K2ACEFS

CE1000K2ACEFS

CE1500K2ACEFS

2000

3000

5000

6

8

6-3/4

9

8-1/8

8-1/16

10

45.1

65.2

104.8

152

200

172

229

203

202

250

20.5

29.6

47.5

C

1

CE2000K2ACEFS

CE3000K2ACEFS

CE5000K2ACEFS

Primary: 240 x 480 with Jumpers

Secondary: 24

250

300

350

5-5/8

4-1/2

3-1/4

3-5/8

4-3/16

8.2

9.5

12.2

143

114

83

92

106

3.7

4.3

5.5

C

2

CE0250K2BCEFS

CE0300K2BCEFS

CE0350K2BCEFS

500

750

1000

5-5/8

6-1/2

6

4-1/2

5-1/4

6-3/8

4-11/16

5-15/16

7

14.4

19.5

26.2

143

165

152

114

133

162

119

151

178

6.5

8.9

11.9

C

2

CE0500K2BCEFS

CE0750K2BCEFS

CE1000K2BCEFS

Primary: 120 x 240 with Jumpers

Secondary: 24

250

300

350

5-5/8

4-1/2

3-1/4

3-5/8

4-3/16

8.3

9.3

12.0

143

114

83

92

106

3.8

4.2

5.4

C

3

CE0250K1BCEFS

CE0300K1BCEFS

CE0350K1BCEFS

500

750

1000

5-5/8

6-1/2

6

4-1/2

5-1/4

6-3/8

4-13/16

5-15/16

7

14.4

19.5

25.2

143

165

152

114

133

162

122

151

178

6.5

8.9

11.4

C

3

CE0500K1BCEFS

CE0750K1BCEFS

CE1000K1BCEFS

Primary: 200/220/440, 208/230/460, 240/480

Secondary: 23/110, 24/115, 25/120

250

300

350

3-7/8

4-1/2

4-7/16

4-3/4

5-3/16

12.5

14.0

15.3

98

114

113

121

140

5.7

6.3

6.9

B

7

CE0250K5ECEFS

CE0300K5ECEFS

CE0350K5ECEFS

500

750

1000

5-1/16

7-3/16

6

5-1/4

6-3/8

6-1/4

5-13/16

7-1/16

20.8

29.8

30.2

129

183

152

133

162

159

148

179

9.4

13.5

13.7

B

C

7

CE0500K5ECEFS

CE0750K5ECEFS

CE1000K5ECEFS

Primary: 220/380/440/550, 230/400/460/575, 240/416/480/600

Secondary: 23/110, 24/115, 25/120

250

300

350

3 7/8

3-7/8

4-7/16

4 1/2

4-1/2

5-1/4

5 3/8

5-11/16

5-1/2

14.3

15.8

16.5

98

113

114

133

137

144

140

6.5

7.2

7.5

B

14

CE0250K2UCEFS

CE0300K2UCEFS

CE0350K2UCEFS

500

750

1000

5-1/16

7-3/16

6

5-1/4

6-3/8

6-3/16

5-11/16

8-1/8

20.5

28.8

39.4

129

183

152

133

162

157

144

207

9.3

13.1

17.9

B

C

14

CE0500K2UCEFS

CE0750K2UCEFS

CE1000K2UCEFS

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-59

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Table 44-66. Type MTK CE Marked with Factory Mounted Finger-Safe Terminal Covers IP20

See Pages 44-54 and 44-55 for Wiring Diagrams.

24 volt secondary only available through 1000 VA.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

Note: Contact your local Eaton sales ofﬁce for availability on additional CE Marked control transformers.

VA Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Terminal

Type

Wiring

Diagram 

Style

Number

Pricing

U.S. $

Height Width Depth Height Width Depth

Primary: 208/230/400/460/575

Secondary: 24 /115/230

250

300

350

500

3-7/8

4-7/16

4-1/2

5-1/4

5-1/2

6-1/16

5-3/4

7-5/16

14.9

17.4

17.8

26.6

98

113

114

133

140

154

146

186

6.8

7.9

8.1

12.1

B

15

CE0250K2VCEFS

CE0300K2VCEFS

CE0350K2VCEFS

CE0500K2VCEFS

750

1000

1500

5-15/16

6-1/4

6

6-3/8

6-3/4

6-3/16

7-3/4

32.5

44.0

45.4

151

159

152

162

172

157

199

14.7

20.0

20.6

B

C

15

16

CE0750K2VCEFS

CE1000K2VCEFS

CE1500K2WCEFS

2000

3000

5000

7-5/8

9

7-5/8

8-3/4

10-7/16

58.6

92.9

127.4

194

229

194

222

265

26.6

42.1

57.8

C

16

CE2000K2WCEFS

CE3000K2WCEFS

CE5000K2WCEFS

Primary: 240/416/480/600, 230/400/460/575, 220/380/440/550, 208/500

Secondary: 99/120/130, 95/115/125, 91/110/120, 85/100/110

250

300

350

4

4-1/2

5-1/16

5-1/2

11.4

13.6

14.2

102

114

135

140

5.2

6.2

6.4

A

8

CE0250K6UCEFS

CE0300K6UCEFS

CE0350K6UCEFS

500

750

1000

4-1/2

5-1/2

5-1/4

6-3/8

5-5/8

7

17.4

27.5

27.9

114

140

133

162

143

187

178

7.9

12.5

12.6

A

8

CE0500K6UCEFS

CE0750K6UCEFS

CE1000K6UCEFS

1500

2000

3000

6

8

7-5/8

6-3/4

9

7-3/4

7-5/8

8-9/16

43.1

56.0

76.2

152

203

194

172

229

199

194

217

19.5

25.4

34.6

A

B

8

CE1500K6UCEFS

CE2000K6UCEFS

CE3000K6UCEFS

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-60

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

CE Marked

Table 44-67. Acceptable Rating of Primary Overcurrent Protection for CE Marked Control Transformers

Table 44-68. Acceptable Maximum Rating of Secondary Overcurrent Protection

Note: For values over 6.3A use 10 x 38 mm time-lag (IEC - 269-3-1). T

a = 40°C Control Type.

Fuses 10 x 38 mm (13/32” x 1-1/2”) Time-lag (IEC 269)

Sec. Voltage 50 75 100 150 200 250 300 350 500 750

115

120

200

2.0

1.0

2.0

4.0

2.0

4.0

6.0

4.0

6.0

4.0

8.0

4.0

10.0

6.0

12.0

8.0

20.0

12.0

208

220

230

1.0

2.0

1.0

2.0

4.0

6.0

8.0

6.0

12.0

10.0

240

277

380

1.0

.5

1.0

2.0

1.0

4.0

2.0

4.0

2.0

4.0

6.0

10.0

8.0

6.0

400

415

440

.5

1.0

2.0

1.0

2.0

4.0

2.0

4.0

6.0

460

480

550

.5

1.0

.5

1.0

2.0

1.0

2.0

4.0

2.0

4.0

6.0

4.0

575

600

.5

1.0

2.0

4.0

Miniature Fuses 5 x 20 mm Time-lag (IEC 127-2/III)

Sec. Voltage 50 75 100 150 200 250 300 350 500 750

23

24

25

2.50

4.00

5.00

8.00

10.0

12.00

16.00

25.00

—

32.00

90

95

100

.63

.50

1.00

.80

1.25

1.00

2.00

1.60

2.50

2.00

3.15

2.50

4.00

3.15

4.00

6.30

5.00

10.00

8.00

110

115

120

.50

.80

.63

1.00

1.60

1.25

2.00

2.50

3.15

2.50

4.00

3.15

5.00

8.00

6.30

220

230

240

.25

.40

.315

.50

.80

.63

1.00

1.25

1.60

1.25

1.60

2.50

4.00

3.15

April 2009

CA08102001E For more information visit: www.eaton.com

44-61

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type AP

Type AP Transformer

Product Description

■Sand and Resin encapsulated

designs.

Application Description

Transformers provide stepped down

voltages to machine tool control

devices enabling control circuits to be

isolated from all power and lighting

circuits. This allows the use of

grounded or ungrounded circuits that

are independent of the power or light-

ing grounds; greater safety is afforded

the operator. The control transformer

line is particularly adaptable on appli-

cations where compact construction

is demanded.

Features, Beneﬁts

and Functions

■UL recognized.

■Resin encapsulated.

■60 Hz operation.

■115°C winding rise.

■Convenient screw-type terminal

board.

■Bottom or side/wall mounting

designs.

■Performance meets/exceeds

requirements of ANSI/NEMA ST-1.

■Regulation exceeds ANSI/NEMA

requirements for all ratings.

Standards and Certiﬁcations

Industry Standards

All Cutler-Hammer dry-type distribution

and control transformers by Eaton

Corporation are built and tested in

accordance with applicable NEMA,

ANSI and IEEE Standards.

Product Speciﬁcations

Overload Capability

Short-term overload is designed into

transformers as required by ANSI.

dry-type distribution transformers

will deliver 200% nameplate load for

one-half hour; 150% load for one-hour;

and 125% load for four-hours without

being damaged provided that a con-

stant 50% load precedes and follows

the overload. See ANSI C57.96-01.250

for additional limitations.

Continuous overload capacity is not

deliberately designed into a trans-

former because the design objective is

to be within the allowed winding tem-

perature rise with nameplate loading.

Insulation System and Temperature Rise

Industry standards classify insulation

systems and rise as shown below:

Table 44-69. Insulation System Classiﬁcation

The design life of transformers having

different insulation systems is the

same — the lower temperature systems

are designed for the same life as the

higher temperature systems.

Sound Levels

All Cutler-Hammer 600 volt class gen-

eral purpose dry-type distribution

transformers are designed to meet

NEMA ST-20 levels.

Winding Terminations

Eaton recommends external cables be

rated 90ºC (sized at 75°C ampacity) for

encapsulated designs.

Series-Multiple Windings

Series-multiple windings consist of

2 similar coils in each winding which

can be connected in series or parallel

(multiple). Transformers with series-

multiple windings are designated with

an “X” or “/” between the voltage

ratings, such as voltages of “120/240”

or “240 X 480.” If the series-multiple

winding is designated by an “X,” the

winding can be connected only for a

series or parallel. With the “/” designa-

tion, a mid-point also becomes avail-

able in addition to the series or parallel

connection. As an example, a 120 X

240 winding can be connected for

either 120 (parallel) or 240 (series), but

a 120/240 winding can be connected

for 120 (parallel), or 240 (series), or 240

with a 120 mid-point.

Ambient +

Winding

Rise

+

Hot

Spot

=

Temp.

Class

40°C

55°C

80°C

115°C

150°C

10°C

30°C

105°C

150°C

185°C

220°C

April 2009

44-62

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Industrial Control Transformers

Type AP

Product Selection

Additional Product Selection information begins on Page 44-63.

Table 44-70. Type AP

See Page 44-34 for Wiring Diagrams.

Note: For additional information, refer to the Cutler-Hammer Industrial Control Transformer Binder B1228A.

kVA Mounting Dimensions (Inches) Weight

Lbs.

Dimensions (mm) Weight

kg

Frame Wiring

Diagram 

Style

Number

Price

U.S. $

Height Width Depth Height Width Depth

240/480 Volts to 120/240 Volts, 60 Hz

3

5

7.5

10

15

Bottom

8-5/16

10-3/4

12

9-9/16

10-3/4

13-3/16

8-13/16

8 -11/16

10-3/16

11-3/8

10-7/16

65

104

129

148

197

227

273

305

243

273

335

224

221

259

289

265

29.5

47.2

58.6

67.2

89.4

FR133

FR99

FR100

FR101

FR134

5

C0003P7GB

C0005P7GB

C0007P7GB

C0010P7GB

C0015P7GB

3

5

7.5

10

15

Side/Wall

9-3/4

11-5/8

12-7/8

8-13/16

8-11/16

10-13/16

11-3/8

10-7/16

9-9/16

10-3/4

13-3/16

65

104

129

148

197

248

295

327

224

221

275

289

265

243

273

335

29.5

47.2

58.6

67.2

89.4

FR292

FR256

FR257

FR258

FR259

5

C0003P7GS

C0005P7GS

C0007P7GS

C0010P7GS

C0015P7GS

For other ratings or styles not shown, or for

special enclosure types (including stainless

steel), refer to Eaton. Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-63

Distribution & Control Transformers and Power Supplies

44

General Purpose & Industrial Control Transformers

Technical Data and Speciﬁcations

Product Selection

Single-Phase Transformers

How to Select Single-Phase Units

1. Determine the primary (source)

voltage — the voltage presently

available.

2. Determine the secondary (load)

voltage — the voltage needed at

the load.

3. Determine the kVA load:

— If the load is deﬁned in kVA, a

transformer can be selected from

the tabulated data.

— If the load rating is given in

amperes, determine the load kVA

from the below chart. To determine

kVA when volts and amperes are

known, use the formula:

kVA = Volts x Amperes

1000

— If the load is an ac motor, deter-

mine the minimum transformer

kVA from the chart at the right.

— Select a transformer rating

equal to or greater than the

load kVA.

4. Deﬁne tap arrangements needed.

5. Deﬁne temperature rise.

Using the above procedure, select

the transformer from the listings in

this catalog.

Table 44-71. Single-Phase ac Motors

If motors are started more than once per hour, increase minimum transformer kVA by 20%.

Note: When motor service factor is greater than 1, increase full load amperes proportionally.

Example: If service factor is 1.15, increase above ampere values by 15%.

Table 44-72. Full Load Current in Amperes — Single-Phase Circuits

Horsepower Full Load Amperes Minimum

Transformer kVA 

115 Volts 208 Volts 220 Volts 230 Volts

1/6

1/4

1/3

4.4

5.8

7.2

2.4

3.2

4.0

2.3

3.0

3.8

2.2

2.9

3.6

.53

.70

.87

1/2

3/4

1

9.8

13.8

16

5.4

7.6

8.8

5.1

7.2

8.4

4.9

6.9

8

1.18

1.66

1.92

1-1/2

2

3

20

24

34

11.0

13.2

18.7

10.4

12.5

17.8

10

12

17

2.40

2.88

4.10

5

7-1/2

10

56

80

100

30.8

44

55

29.3

42

52

28

40

50

6.72

9.6

12.0

kVA Voltage

120 208 220 240 277 480 600 2400 4160

.25

.50

.75

2.0

4.2

6.3

1.2

2.4

3.6

1.1

2.3

3.4

1.0

2.1

3.1

.9

1.8

2.7

.5

1.0

1.6

.4

.8

1.3

.10

.21

.31

.06

.12

.18

1

1.5

2

8.3

12.5

16.7

4.8

7.2

9.6

4.5

6.8

9.1

4.2

6.2

8.3

3.6

5.4

7.2

2.1

3.1

4.2

1.7

2.5

3.3

.42

.63

.83

.24

.36

.48

3

5

7.5

25

41

62

14.4

24.0

36

13.6

22.7

34

12.5

20.8

31

10.8

18.0

27

6.2

10.4

15.6

5.0

8.3

12.5

1.2

2.1

3.1

.72

1.2

1.8

10

15

25

83

125

208

48

72

120

45

68

114

41

62

104

36

54

90

20.8

31

52

16.7

25

41

4.2

6.2

10.4

2.4

3.6

6.0

37.5

50

75

312

416

625

180

240

360

170

227

341

156

208

312

135

180

270

78

104

156

62

83

125

15.6

20.8

31.3

9.0

12.0

18.0

100

167

833

1391

480

802

455

759

416

695

361

602

208

347

166

278

41.7

69.6

24.0

40.1

April 2009

44-64

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

General Purpose & Industrial Control Transformers

Technical Data and Speciﬁcations

Three-Phase Transformers

How to Select Three-Phase Units

1. Determine the primary (source)

voltage — the voltage presently

available.

2. Determine the secondary (load)

voltage — the voltage needed at

the load.

3. Determine the kVA load:

— If the load is deﬁned in kVA, a

transformer can be selected from

the tabulated data.

— If the load rating is given in

amperes, determine the load kVA

from the below chart. To determine

kVA when volts and amperes are

known, use the formula:

kVA = Volts x Amperes x 1.732

1000

— If the load is an ac motor, deter-

mine the minimum transformer

kVA from the chart at the right.

— Select a transformer rating

equal to or greater than the

load kVA.

4. Deﬁne tap arrangements needed.

5. Deﬁne temperature rise.

Using the above procedure, select

the transformer from the listings in

this catalog.

Table 44-73. Three-Phase ac Motors

If motors are started more than once per hour, increase minimum transformer kVA by 20%.

Note: When motor service factor is greater than 1, increase full load amperes proportionally.

Example: If service factor is 1.15, increase above ampere values by 15%.

Table 44-74. Full Load Current in Amperes — Three-Phase Circuits

Horsepower Full Load Amperes Minimum

Transformer kVA 

208 Volts 230 Volts 380 Volts 460 Volts 575 Volts

1/2

3/4

1

2.2

3.1

4.0

2.0

2.8

3.6

1.2

1.7

2.2

1.0

1.4

1.8

.8

1.1

1.4

.9

1.2

1.5

1-1/2

2

3

5.7

7.5

10.7

5.2

6.8

9.6

3.1

4.1

5.8

2.6

3.4

4.8

2.1

2.7

3.9

2.1

2.7

3.8

5

7-1/2

10

16.7

24

31

15.2

22

28

9.2

14

17

7.6

11

14

6.1

9

11

6.3

9.2

11.2

15

20

25

46

59

75

42

54

68

26

33

41

21

27

34

17

22

27

16.6

21.6

26.6

30

40

50

88

114

143

80

104

130

48

63

79

40

52

65

32

41

52

32.4

43.2

52

60

75

100

170

211

273

154

192

248

93

116

150

77

96

124

62

77

99

64

80

103

125

150

200

342

396

528

312

360

480

189

218

291

156

180

240

125

144

192

130

150

200

kVA Voltage

208 240 380 480 600 2400 4160

3

6

9

8.3

16.6

25

7.2

14.4

21.6

4.6

9.1

13.7

3.6

7.2

10.8

2.9

5.8

8.6

.72

1.4

2.2

.42

.83

1.2

15

22.5

30

41.7

62.4

83.4

36.1

54.1

72.3

22.8

34.2

45.6

18.0

27.1

36.1

14.4

21.6

28.9

3.6

5.4

7.2

2.1

3.1

4.2

37.5

45

50

104

124

139

90.3

108

120

57.0

68.4

76

45.2

54.2

60.1

36.1

43.4

48.1

9.0

10.8

12.0

5.2

6.3

6.9

75

112.5

150

208

312

416

180

270

360

114

171

228

90

135

180

72

108

144

18.0

27.1

36.1

10.4

15.6

20.8

225

300

500

624

832

1387

541

721

1202

342

456

760

270

360

601

216

288

481

54.2

72.2

120

31.3

41.6

69.4

750

1000

2084

2779

1806

2408

1140

1519

903

1204

723

963

180

241

104

139

April 2009

CA08102001E For more information visit: www.eaton.com

44-65

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSG Series

Contents

Description Page

Power Supply Selection Guide

PSG Series . . . . . . . . . . . . . 44-65

PSS Series . . . . . . . . . . . . . 44-71

ELC Series . . . . . . . . . . . . . 44-77

EZ Power Series . . . . . . . . 44-80

Sensor Power Supplies . . 44-81

Table 44-75. Power Supply Selection Guide

Power Supply

Series

PSG PSS ELC EZ Power Series Sensor Power Supplies

Features ■General purpose

24V DC control

■Rugged metal housing

■DIN-rail mount

■150% current boost for

1 sec (outrush)

■Single-phase

(85 – 264V AC/120 – 375V DC)

or 3-phase (320 – 575V AC/

450 – 800V DC) inputs

■Class 1, Division 2 qualiﬁed

(February 2009)

■Conformal coated

electronics

■24V DC control for high

start-up loads

■Peak current surge

(boost/outrush) up to

6 times nominal current

■Semi 47 approved

■Long ride-through

capability

■Pluggable terminal

connections

■Single-phase and 3-phase

inputs up to 600V AC

■Compact, low cost

24V DC control for

loads up to 2A

■Plastic enclosure

can be DIN-rail or

panel mounted

■Class 1, Division 2

qualiﬁed

■Single-phase

(85 – 264V AC)

input

■Shallow-depth power

supplies for 12V DC or

24V DC applications

■Low-power output —

up to 1.25A

■EZ Relay styling

provides optimal

panel aesthetics

■Plastic enclosure can

be DIN-rail or panel

mounted (with

optional kit)

■Class 1, Division 2

qualiﬁed

■Single-phase

(85 – 264V AC) input

■27V DC supplies

for tough sensor

applications

■Rugged housings

with integrated

junction box for

mounting outside of

electrical enclosures

■Advanced diagnostic

features

April 2009

44-66

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSG Series

Product Description

Eaton’s PSG Series of power supplies

is designed to be a high-performance,

high-quality line of products covering

a majority of 24V DC control applica-

tions. With global certiﬁcations, com-

pact size, and an impressive operating

temperature range, the PSG series ﬁts

a wide variety of applications at a

competitive price.

Eight models are offered, from 2.5A up

to 20A with both single and 3-phase

input voltage models available.

Application Description

The PSG series is a line of general-

purpose power supplies for use in a

wide variety of industrial control appli-

cations. Applications include commu-

nication networks, sensors, PLCs, and

many other electrical systems.

Each model is equipped with a rugged

metal housing, heavy-duty screw

terminals, and a variety of protection

features, making the PSG one of the

most versatile industrial power supply

lines on the market.

Features, Beneﬁts

and Functions

■Universal input voltages:

85 – 264V AC for single-phase units,

320 – 575V AC for 3-phase units.

■Rugged aluminum housing stands

up to harsh environments.

■Current surge (power boost) of

1.5 times nominal current for

1 sec. allows branch protection

and powering of high pick-up loads.

■Wide operating temperature range:

-20°C to +75°C (derating above 50°C).

■Adjustable DC voltage output.

■LED indicating light for DC OK

simpliﬁes troubleshooting.

■Compact size, with common depth

and height across all models allows

for common panel depths and

family consistency.

■MTBF up to 800,000 hours ensures

uptime and reliability.

■Heavy duty screw terminals with

ﬁnger-safe protective cover allow

use of ring-lug terminals.

■All-metal DIN-rail mounting

hardware.

■Class 1, Division 2 hazardous

location rated (February 2009).

Standards and Certiﬁcations

■UL/cUL Listed – UL 508.

■CSA Certiﬁed (contact Eaton for

certiﬁcation dates and status).

■CE Marked.

■RoHS Compliant.

Product Selection

Table 44-76. Product Selection

Figure 44-55. Power Derating Curve Vertical

Mounting Position PSG60E

Figure 44-56. Power Derating Curve Vertical

Mounting Position PSG60F, PSG120E,

PSG120F, PSG480E, PSG480F

Figure 44-57. Power Derating Curve Vertical

Mounting Position PSG240E, PSG240F

Description Catalog Number Price U.S. $

Power Supply – Single-phase 85 – 264V AC input, 24V DC / 2.5A output PSG60E

Power Supply – 3-phase 320 – 575V AC input, 24V DC / 2.5A output PSG60F

Power Supply – Single-phase 85 – 264V AC input, 24V DC / 5A output PSG120E

Power Supply – 3-phase 320 – 575V AC input, 24V DC / 5A output PSG120F

Power Supply – Single-phase 85 – 264V AC input, 24V DC / 10A output PSG240E

Power Supply – 3-phase 320 – 575V AC input, 24V DC / 10A output PSG240F

Power Supply – Single-phase 85 – 264V AC input, 24V DC / 20A output PSG480E

Power Supply – 3-phase 320 – 575V AC input, 24V DC / 20A output PSG480F

Load (%)

Ambient Temperature (°C)

-20 -10 0 10 20 30 40 50 60 70 80 85

110

100

90

80

70

60

50

40

30

20

10

0

Load (%)

Ambient Temperature (°C)

-20 -10 0 10 20 30 40 50 60 70 80 85

110

100

90

80

70

60

50

40

30

20

10

0

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

Load (%)

Ambient Temperature (°C)

-20 -10 0 10 20 30 40 50 60 70 80 85

110

100

90

80

70

60

50

40

30

20

10

0

April 2009

CA08102001E For more information visit: www.eaton.com

44-67

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSG Series

Technical Data and Speciﬁcations

Table 44-77. PSG Technical Speciﬁcations

Ratings for single-phase models are at 115V AC; 3-phase models are at 400V AC.

Capacity PSG60E PSG120E PSG240E PSG480E PSG60F PSG120F PSG240F PSG480F

60W 120W 240W 480W 60W 120W 240W 480W

Input

Nominal Voltage 100 – 240V AC 3 x 400 – 500V AC

Voltage Range 85 – 264V AC (DC input range 120 – 375V DC) 320 – 575V AC (DC input range 450 – 800V DC)

Frequency 47-63 Hz (0 Hz at DC input)

Nominal Current 1.1A 1.4A 2.9A 5.7A 0.3A 0.5A 0.8A 1.6A

Inrush Current Limitation 30A <80A N/A N/A <30A <30A <40A <50A

Mains Buffering @ Nominal

Load (Typ.) 

>20 ms >35 ms >20 ms >20 ms >30 ms >35 ms >35 ms >20 ms

Turn-on Time <2.5 sec <1 sec <1 sec <1 sec <2 sec <1 sec <1 sec <1 sec

Internal Fuse T3.15 AH/250V T6.3AH/250V F10H/250V 3.15AH/500V

External Fusing 6A, 10A, or 16A 10A or 16A 3 x circuit breakers 6A, 10A or 16A

Leakage Current <1 mA <1 mA <3.5 mA <1 mA <3.5 mA

Output

Nominal Output Voltage 24V DC +/- 2%

Adjustment Range 22 – 28V DC

Nominal Current 2.5A 5A 10A 20A 2.5A 5A 10A 20A

Startup With Capacitive Loads Max. 8,000 FMax. 10,000 F

Max. Power Dissipation Idling/

Nominal Load Approx.

10 W 22.5 W 42.5 W 72 W 9 W 18 W 36 W 72 W

Efﬁciency (@ 400V AC and

Nominal Values)

>85% typ >84% typ >84% typ >86% typ >86% @ 3 x 400V AC

>85% @ 3 x 500V AC

>87% @ 3 x 400V AC

>86% @ 3 x 500V AC

Current Surge (@ 24V DC) 3.75A 7.5A 15A 30A 3.75A 7.5A 15A 30A

Current Surge Time/Cycle 1 second (at 10-second intervals)

Residual Ripple/Peak Switching

(20 Mhz)

<50 mV/<240mVpp

Parallel Operation With Oring Diode

Galvanic Isolation

Input/Output 4 kVAC (type test)/3 kVAC (routine test)

Input/Ground 1.5 kVAC (type test)/1.5 kVAC (routine test)

Output/Ground 1.5 kVAC (type test)/500V AC (routine test)

General/Physical Data

Housing Material Aluminum (Al5052)

Signals Green LED for DC OK

MTBF >800,000 hrs >300,000 hrs >500,000 hrs >300,000 hrs

Dimensions (L) 121 mm

Dimensions (W) 32 mm 50 mm 85 mm 160 mm 70 mm 70 mm 85 mm 160 mm

Dimensions (H) 120 mm 115 mm 118.5 mm 115 mm 118.5 mm 118.5 mm 120.5 mm 115 mm

Weight (kg) 0.37 0.54 1.04 1.8 0.56 0.72 0.77 1.71

Operating Temperature -20°C to +75°C (>50°C derating)

Storage Temperature -25°C to +85°C

Operating Humidity <95% RH, non-condensing

Vibration (Operating) 10 to 150 Hz, 0.35 mm acc. 50 m/s/s, single amplitude (5 G max) for 90 min. in each X, Y, Z direction, in acc. with IEC 68-2-6

Pollution Degree 2

Climatic Class 3K3 according to EN 60721

Approvals/Certiﬁcations

UL/cUL Listed-UL508 (Industrial Control Equipment), cURus-UL60950-1, CSA, CE, IEC, EN, German Safety, RoHS

Safety & Protection

Transient Surge Voltage Varistor

Surge Voltage Protection

Against Interal Surge

Yes

Safety Class Class I with ground connection

Shock 30 G (300 m/s/s) in all directions according to IEC 68-2-27

April 2009

44-68

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSG Series

Dimensions

Figure 44-58. PSG60E — Approximate Dimensions in mm

Figure 44-59. PSG60F — Approximate Dimensions in mm

Figure 44-60. PSG120E — Approximate Dimensions in mm

32.0 ±0.5

5.0 ±0.2

Catalog Number:

PSG60E

24V 2.5A

Adjust

DC OK

100-240V~1.5A

50-60Hz

SPEC LABEL

CAUTION

HOT SURFACE

121.0 ±0.5

105.2 ±0.5

120.5 ±0.5

Note: Dimensions are

for reference only.

70.0 ±0.5

SPEC LABEL

121.0 ±0.5

111.4 ±0.5

96.5 ±0.5

6.6 ±0.1

Note: Dimensions are

for reference only.

115.0 ±0.6

13.0 4.0

5.5

121.0 ±0.2

DC 24V 5A

AC 100-240V 2A

50-60 Hz

Adjust

DC OK

50.0 ±0.2

Note: Dimensions are

for reference only.

April 2009

CA08102001E For more information visit: www.eaton.com

44-69

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSG Series

Dimensions

Figure 44-61. PSG120F — Approximate Dimensions in mm

Figure 44-62. PSG240E — Approximate Dimensions in mm

Figure 44-63. PSG240F — Approximate Dimensions in mm

70.0 ±0.5

121.0 ±0.5

111.3 ±0.5

96.4 ±0.5

SPEC LABEL

Adjust

DC OK

6.6 ±0.1

Note: Dimensions are

for reference only.

5.0 ±0.2

SPEC LABEL

CAUTION

HOT SURFACE

Catalog Number:

PSG240E

Adjust

DC OK

24V 10A

100-240V~5A

50-60Hz

121.0 ±0.5

105.2 ±0.5

118.5 ±0.5

85.0 ±0.5

Note: Dimensions are

for reference only.

Catalog Number:

PSG240F

Adjust

DC OK

24V 10A

3-Phase 400-500V~0.8A 50-60Hz

5.0 ±0.2

SPEC LABEL

CAUTION

HOT SURFACE

121.0 ±0.5

105.2 ±0.5

120.5 ±0.5

85.0 ±0.5

Note: Dimensions are

for reference only.

April 2009

44-70

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSG Series

Dimensions

Figure 44-64. PSG480E — Approximate Dimensions in mm

Figure 44-65. PSG480F — Approximate Dimensions in mm

121.0 ±0.5

24V 20A

Catalog Number:

PSG480E

100-240V~ 7A 50-60Hz

160.0 ±0.5 7.1

6.6 ±0.1

111.4 ±0.5

96.6 ±0.5

N L Adjust

DC OK

Note: Dimensions are

for reference only.

121.0 ±0.5

160.0 ±0.5

96.6 ±0.5

111.4 ±0.5

Catalog Number:

PSG480F

24V 20A

3-Phase 400-500V~1.4A 50-60Hz

Adjust

DC OK

7.1

6.6 ±0.1

Note: Dimensions are

for reference only.

April 2009

CA08102001E For more information visit: www.eaton.com

44-71

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSS Series

Product Description

Eaton’s PSS Series of power supplies is

designed to work in a variety of appli-

cations, including the power supply to

the IT. line of power control products.

They also work in most control applica-

tions that require 24V DC. All of the

PSS power supplies are designed to

provide the highest “outrush” current

in the industry for units of their size.

It is also the only line to provide 110 –

480V AC input voltage down to the

smallest current units.

Application Description

The PSS line of power supplies is

speciﬁcally designed to work with the

S801, S811, MV811 and IT. electro-

mechanical devices. They can also

serve in a variety of other applications,

including support of sensors, operator

interfaces, PLCs, communication net-

works, heaters and lights and in many

other industrial applications where

24V DC power supplies are required.

With the widest operating temperature

range in the industry, rugged design

and a long list of advanced features,

they can be applied in a very wide range

of applications.

The higher input voltage ranges are

designed to allow users to eliminate

the need for a control power trans-

former in the enclosure or cabinet,

thus saving space, wiring and money.

Features

■Wide range voltage input

(110 – 480V AC operating).

■High current outrush capability

in all units.

■Semiconductor F47 approved.

■Long ride-through capability

designed in.

■Wide operating temperature range.

■Power supplies can be used in

parallel (6.5A and greater).

■Multiple 24V DC terminals for

easy wiring.

■DIN-rail and panel mount available

in most units.

■Removable terminal connections.

■IP20 ﬁngerproof design.

■Larger units have —

❑Active power factor correction

❑Adjustable output voltages

❑Fault contacts

❑Analog outputs

Beneﬁts

■24V DC control enhances personnel

and equipment safety.

■IP20 design improves personnel

safety.

■Removable terminal connectors

make installation and repair quick

and easy.

■Wide operating temperature range

allows for installation in most areas

where standard control products

can be installed today.

■High current outrush capability

allows use of smaller power

supplies in many applications

and ensures stable output during

high power demand cycles.

■Due to long ride-through time, the

Power Supply can maintain the

control power system during brown

out and black out conditions.

Standards and Certiﬁcations

■UL Listed 508.

■CSA Certiﬁed.

■CE Marked.

■F47 Certiﬁed.

PSS Supplies

April 2009

44-72

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSS Series

Catalog Number Selection

Table 44-78. PSS Catalog Numbering System

Product Selection

Table 44-79. Power Supply Product Selection

Table 44-80. PSS Sizing Chart

Steady State

Current (Amps)

Steady State

Wattage

Input

Voltage

Catalog

Number

Price

U.S. $

.4 10W 110 – 240

380 – 480

PSS10E

PSS10F

1.0 25W 110 – 240

380 – 480

PSS25E

PSS25F

2.3 55W 110 – 240

190 – 264

360 – 480

480 – 600

PSS55A

PSS55B

PSS55C

PSS55D

6.5 160W 110 – 240

380 – 480

PSS160E

PSS160C

12.5 300W 90 – 264

380 – 480

PSS300E

PSS300C

25.0 600W 380 – 480 PSS600C

40.0 1000W 380 – 480 PSS1000C

P S S 5 5 A

Model

PSS = Power Supply Switcher

Nominal Input Voltage Rating

A = 115V AC

B = 230V AC

C = 360 – 480V AC

(3-phase)

D = 480 – 600V AC

E = 110 – 240V AC

F = 380 – 480V AC

Wattage Rating

10 = 10 Watts

25 = 25 Watts

55 = 55 Watts

160 = 160 Watts

300 = 300 Watts

600 = 600 Watts

1000 = 1000 Watts

Frame

Size

IEC

Size

NEMA

Size

Steady State

Current

Inrush

Amps Durahon

27 mm A N/A .83A .83A 30 mS

45 mm B 00, 0 .13A 3.30A 50 mS

54 mm C 1 .15A 3.80A 50 mS

76 mm D 2 .21A 5.40A 65 mS

105 mm E 3, 4 .23A 5.80A 85 mS

140 mm F 5 .54A 8.30A 250 mS

Accessories

DIN-Rail Mounting Kit

Table 44-81. Kits

Description Catalog

Number

Price

U.S. $

DIN-Rail Mounting Kit PSSDIN

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

CA08102001E For more information visit: www.eaton.com

44-73

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSS Series

Technical Data and Speciﬁcations

Table 44-82. Power Supply Speciﬁcations

Capacity PSS10E PSS10F PSS25E PSS25F PSS55A PSS55B PSS55C PSS55D

10W 10W 25W 25W 55W 55W 55W 55W

Input

Voltage 110 to 240V AC 380 to 480V AC 110 to 240V AC 380 to 480V AC 115V AC 230V AC 380 to 480V AC

3-Phase

480 to 600V AC

3-Phase

Input Current

(RMS)

.19A .1A .45A .17A .9A .54A .20A/Phase .07A/Phase

Frequency 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz

Voltage Range ± 10% ± 10% ± 10% ± 10% ± 15% ± 15% ± 10% ± 15%

Inrush Current 25A 25A 35A 35A 16A 32A 15A 15A

Overvoltage 330V AC 550V AC 330V AC 550V AC Varistor Varistor Varistor Varistor

Internal Input Fuse T2A @ 250V T2A @ 250V T4A @ 250V T2A @ 250V T2A @ 250V T2A @ 250V 3 x T2A @ 250V —

External Fusing Not Required 2A 250V AC Slow Blow 3 x 1A 600V AC

Slow Blow

Output

Voltage Nominal 24V DC 24V DC 24V DC 24V DC 24V DC 24V DC 24V DC 24V DC

Voltage Regulation ±10% ±10% ±10% ±10% ±3.5% ±3.5% ±3.5% ±3.5%

Current Nominal .4A .4A 1.0A 1.0A 2.3A 2.3A 2.3A 2.3A

Voltage Adj. Range None None None None None None None None

Current Surge 1A 1A 6.8A 6.8A 10A 10A 10A 10A

Current Surge

Time

35 mS 35 mS 85 mS 85 mS 180 mS 180 mS 180 mS 180 mS

Surge Cycle Time 10 sec 10 sec 10 sec 10 sec

Hold Up Time 100 mS 100 mS 100 mS 100 mS 70 mS 70 mS 24 mS 30 mS

Max. Load

Capacitance

10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF

Switching

Frequency

60k Hz 60k Hz 100k Hz 100k Hz 100k Hz 100k Hz 100k Hz 61k Hz

Efﬁciency @

Max. Load

80% 75% 80% 80% 80% 80% 80% 85%

Output Ripple ±1% ±1% ±1% ±1% ±1% ±1% ±1% ±1%

April 2009

44-74

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSS Series

Table 44-82. Power Supply Speciﬁcations (Continued)

Capacity PSS10E PSS10F PSS25E PSS25F PSS55A PSS55B PSS55C PSS55D

10W 10W 25W 25W 55W 55W 55W 55W

Protection

Short Circuit Auto restart Auto restart Auto restart Auto restart Auto restart Auto restart Auto restart Auto restart

Over Voltage No No No No No No No No

Under Voltage No No No No No No No No

Over

Temperature

None. Software in Micro Controller

Over Current 0.8A typical

@ 24V for

>100 mS

0.8A typical

@ 24V for

>160 mS

6.8 A typical

@ 24V for

>160 mS

6.8A typical

@ 24V for

>160 mS

10A typical

@ 24V for

>300 mS

10A typical

@ 24V for

>300 mS

10A typical

@ 24V for

>300 mS

10A typical

24V for

>300 mS

Galvanic Isolation

Input to Output 1.5 kV 2 kV 1.5 kV 2 kV 3 kV 3 kV 3 kV 4 kV

Input/Output to

Rail

1.5 kV 2 kV 1.5 kV 2 kV 3 kV 3 kV 3 kV 4 kV

Input to Ground 1.5 kV 2 kV 1.5 kV 2 kV 1.5 kV 1.5 kV 1.5 kV 2.0 kV

Output to

Ground

200V 200V 200V 200V 200V 200V 200V 250V

Special Features

Cooling Convection Convection Convection Convection Convection Convection Convection Convection

Load Sharing None None None None None None None None

Redundancy None None None None None None None None

Analog Outputs None None None None None None None None

Fault Relay None None None None None None None None

Wire Size

Input 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG

Output 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG 20 – 14 AWG

I/O None None None None None None None None

Indications

Indicators Green LED (DC on)

Physical Data

Dimensions

Length x Width

x Depth in

inches (mm)

4.49 x 1.97 x 4.49

(114 x 50 x 114)

4.49 x 1.97 x 4.49

(114 x 50 x 114)

4.49 x 1.97 x 4.49

(114 x 50 x 114)

4.49 x 1.97 x 4.49

(114 x 50 x 114)

2.09 x 3.86 x 5.59

(53 x 98 x 142)

2.09 x 3.86 x 5.59

(53 x 98 x 142)

2.32 x 4.21 x 6.73

(59 x 107 x 171)

2.32 x 6.19 x 6

(59 x 157 x 154)

Weight (kg) .57 (.26) .64 (.29) .73 (.33) .81 (.37) 1.06 (.48) 1.06 (.48) 1.17 (.53) 2.45 (1.1)

Mounting and

Recommended

Clearance

TS35 rail or chassis; leave 4 in. (10 cm) free space on venting sides. TS35 Rail (with optional PSSDIN Kit) or Chassis;

Leave 4 in. (10 cm) free space on venting sides.

—

Environmental Performance

Storage

Temperature

-25 to 80°C -25 to 80°C -25 to 80C -25 to 80C -40 to 85°C -40 to 85°C -40 to 85°C -40 to 85°C

Operating

Temperature

-5 to 50°C -5 to 50°C -5 to 50°C -5 to 50°C -25 to 50°C -25 to 50°C -25 to 50°C -25 to 50°C

Storage

Humidity

5 to 95% 5 to 95% 5 to 95% 5 to 95% 5 to 95% 5 to 95% 5 to 95% 5 to 95%

Operating

Humidity

<95% RH non-

condensing

<95% RH non-

condensing

<95% RH non-

condensing

<95% RH non-

condensing

20 to 85% non-

condensing

20 to 85% non-

condensing

20 to 85% non-

condensing

20 to 85% non-

condensing

Approvals/Certiﬁcations

UL, IEC, CSA UL, IEC, CSA UL, IEC, CSA UL, IEC, CSA cULus 1950 Recognized, cULus 508 Listed, CE cCSAus

April 2009

CA08102001E For more information visit: www.eaton.com

44-75

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSS Series

Table 44-82. Power Supply Speciﬁcations (Continued)

Capacity PSS160E PSS160C PSS300E PSS300C PSS600C PSS1000C

160W 160W 300W 300W 600W 1000W

Input

Voltage 115 to 230V AC 380 to 480V AC

3-Phase

115 to 230V AC 380 to 480V AC

3-Phase

380 to 480V AC

3-Phase

380 to 480V AC

3-Phase

Input Current

(RMS)

2.3A/1.4A .43A/Phase 3.3A/1.65A .75A/Phase 1.4A/Phase 1.9A/Phase

Frequency 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz 47 – 63 Hz

Voltage Range ± 10% ± 10% ± 10% ± 10% ± 10% ± 10%

Inrush Current 16/32A 5.7A 30A 40A 40A 40A

Over Voltage Varistor Varistor Varistor Varistor Varistor Varistor

Internal Input Fuse T6.3A @ 250V 3 x T2A @ 500V T5A @ 250V No No No

External Fusing Not Required

3A 250V AC

Slow Blow

Not Required

2A 480V AC

Slow Blow

Not Required

6A 250V AC

Slow Blow

3 x T2A @ 480V AC

Slow Blow

Required 3 x 6A @ 480V AC Slow Blow

Output

Voltage Nominal 24V DC 24V DC 24V DC 24V DC 24V DC 24V DC

Voltage Regulation ±3.5% ±3.5% ±6% ±5% ±6% ±6%

Current Nominal 6.5A 6.5A 12.5A 12.5A 25A 40A

Voltage Adj. Range 22.5 to 28.5V DC 22.5 to 28.5V DC 23 to 28V DC 23 to 28V DC 23 to 28V DC 23 to 28V DC

Current Surge 13A 20A 18A 25A 50A 80A

Current Surge Time 1 sec 1 sec 1 sec 1 sec 1 sec 1 sec

Surge Cycle Time 10 sec 10 sec 10 sec 60 sec 60 sec 60 sec

Hold Up Time 50 mS 15 mS 30 mS 25 mS @ 480V AC 12 mS >14 mS

Max. Load

Capacitance

10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF 10,000 µF

Switching

Frequency

65k Hz 100k Hz 100k Hz 100k Hz 65k Hz 65k Hz

Efﬁciency @

Max. Load

85% 83% 80% 83% 87% 90%

Output Ripple ±1% ±1% ±.1% ±.1% ±.1% ±.1%

PSS160E PSS300E

April 2009

44-76

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

PSS Series

Table 44-82. Power Supply Speciﬁcations (Continued)

Capacity PSS160E PSS160C PSS300E PSS300C PSS600C PSS1000C

160W 160W 300W 300W 600W 1000W

Protection

Short Circuit Auto restart Auto restart Auto restart Auto restart Auto restart Auto restart

Over Voltage No Yes Yes Yes Vout > 30V DC Vout > 30.5V DC

Under Voltage No Yes Yes Yes Vout < 20V DC Vout < 20V DC

Over Temperature None. Software in Micro Controller Vout heatsink temp. is greater than 100°C

Over Current 13A typical @ 24V

for >1 sec

13A typical @ 24V

for >1 sec

20A typical @ 24V

for >1 sec

20A typical @ 24V

for >1 sec

26.5A typical @ 24V

for >1 sec

43A typical @ 24V for

>1 sec

Galvanic Isolation

Input to Output 3 kV 3 kV 3 kV 3 kV 3 kV AC 3 kV AC

Input/Output to Rail 3 kV 3 kV 3 kV 3 kV 1.5 kV AC 1.5 kV AC

Input to Ground 1.5 kV 1.5 kV 1.5 kV 1.5 kV 1.5 kV AC 1.5 kV AC

Output to Ground 500V 500V 500V 500V 500V AC 500V AC

Special Features

Cooling Convection Convection Fan cooled Convection Fan cooled Fan cooled

Load Sharing Maximum 2 units Maximum 2 units Maximum 3 units

(active)

Maximum 2 units Maximum 2 units Maximum 2 units

Redundancy Maximum 2 units Maximum 2 units Maximum 2 units Maximum 2 units Maximum 2 units Maximum 2 units

Analog Outputs None None VDC Out = 3 x V

analog, T = 10 x V

analog, IOUT = 10 x

V analog

None VDC OUT = 3 x V analog, T = 10 x V analog,

IOUT = 10 x V analog

Fault Relay Form C, 125V AC

and 30V DC @ 1A

rating

Form C, 125V AC

and 30V DC @ 1A

rating

Form C contacts (1A

@ 30V DC or 30V AC)

Form C contacts (1A

@ 30V DC or 30V AC)

Form C contacts (1A

@ 30V DC or 30V AC)

Form C contacts (1A

@ 30V DC or 30V AC)

Wire Size

Input 26 – 12 AWG 26 – 12 AWG 22 – 12 AWG 22 – 12 AWG 22 – 12 AWG 22 – 12 AWG

Output 26 – 12 AWG 26 – 12 AWG 22 – 6 AWG 22 – 6 AWG 22 – 6 AWG 22 – 6 AWG

I/O 26 – 12 AWG 26 – 12 AWG 22 – 12 AWG

(.08 – 2.5 mm2)

22 – 12 AWG

(.08 – 2.5 mm2)

22 – 12 AWG

(.08 – 2.5 mm2)

22 – 12 AWG

(.08 – 2.5 mm2)

Indications

Indicators Green LED (DC on)

Physical Data

Dimensions

Length x Width x

Depth in Inches

(mm)

5.0 x 2.2 x 6.8

(127 x 57 x 175)

5.44 x 2.3 x 7

(138.2 x 58.4 x 177.8)

4.1 x 9.53 x 6.1

(104 x 242 x 155)

6.25 x 3.16 x 6.35

(159 x 80 x 161)

6.8 x 9.4 x 5.3

(173 x 238 x 135)

7.2 x 10.6 x 5.3

(182 x 268 x 133)

Weight Lbs. (kg) 1.94 (.88) 2.2 (.99) 2.6 (1.18) 3.0 (1.4) 6.6 (3) 8.35 (3.8)

Mounting and

Recommended

Clearance

TS35 Rail with optional PSSDIN Kit or Chassis (hardware included); leave 4 in. (10 cm) free space on venting sides.

Environmental Performance

Storage

Temperature

-40 to +85°C -40 to +85°C -40 to +85°C -40 to +85°C -40 to +85°C -40 to +85°C

Operating

Temperature

-20 to 50°C -20 to 50°C -20 to 50°C -20 to 50°C -10 to +50°C

(Full Power)

-10 to +50°C

(Full Power)

Storage Humidity 5 to 95% 5 to 95% 4 to 95% 4 to 95% 5 to 95% 5 to 95%

Operating Humidity 20 to 85% non-

condensing

20 to 85% non-

condensing

19 to 85% non-

condensing

19 to 85% non-

condensing

20 to 85% non-

condensing

20 to 85% non-

condensing

Approvals/Certiﬁcations

CE, cULus 508 Listed CE, cULus 508 Listed CE, cULus 508 Listed CE, cULus 508 Listed CE, cULus 508 Listed CSA 22.2 #950-95,

cULus 508 Listed, CE

April 2009

CA08102001E For more information visit: www.eaton.com

44-77

Distribution & Control Transformers and Power Supplies

44

Power Supplies

ELC Power Supply

Product Description

Eaton’s ELC power supplies are the

perfect products for those applications

requiring a very compact and low-cost

source for 24V DC power. While these

products were developed to be a

perfect match for our Eaton Logic

Controllers, they can be used in a

variety of applications.

The lightweight, DIN-rail mounted

enclosures, wide input voltage range,

and robust screw terminals make

these power supplies easy to install

and use. They are available in 1A and

2A models.

Features, Beneﬁts

and Functions

■Universal input voltage: 85-264V AC.

■Compact size, with common depth

and height across models allows for

common panel depths and family

consistency.

■ELC styling provides maximum

aesthetic appeal when used with the

Eaton Logic Controllers.

■Front-mounted pressure plate screw

terminals for a robust connection.

■Removable ﬁnger-safe protective

cover for terminals.

■Power On indication LED.

■Integrated mounting hardware

for panel mounting or DIN-rail

mounting.

Standards and Certiﬁcations

■UL / cUL Listed – UL 508.

■CE Marked.

■RoHS Compliant.

■Class I, Division II for groups A, B,

C, D.

Product Selection

Table 44-83. ELC Product Selection

Technical Data and Speciﬁcations

Table 44-84. Technical Speciﬁcations

Description Catalog

Number

Price

U.S. $

24 Watt, 1 Amp

Power Supply

ELC-PS01

48 Watt, 2 Amp

Power Supply

ELC-PS02

Capacity ELC-PS01 ELC-PS02

24W 48W

Input

Nominal Voltage 100 – 240V AC

Voltage Range 85 – 264V AC

Frequency 47 – 63 Hz

Output

Nominal Output Voltage 24V DC +/- 3%

Nominal Current 1 A 2 A

Efﬁciency 78% to 87% typical at full load

Residual Ripple/Peak Switching (20 MHz) < 100 mV typical @ full load < 240 mV typical @ full load

General/Physical Data

Housing Material Plastic

Dimensions (D) 60 mm

Dimensions (W) 36.5 mm 55 mm

Dimensions (H) 90 mm

Weight (g) 158 250

Operating Temperature 0°C to +55°C

Storage Temperature -25°C to +70°C

Operating Humidity 50% to 95% RH, non-condensing

Pollution Degree 2

Approvals/Certiﬁcations

UL508, CE, RoHS, EMC directive 89/336/EEC, Low voltage directive 73/23/EEC

Safety and Protection

Overload/Short Circuit Protection Auto recovery

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-78

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

ELC Power Supply

Dimensions

Figure 44-66. ELC-PS01 Power Supply — Approximate Dimensions in Inches (mm)

Figure 44-67. ELC-PS02 Power Supply — Approximate Dimensions in Inches (mm)

ELC-PS01

POWER

L

N

24V

0V

2.36

(60.0)

3.54

(90.0)

0.12

(3.0)

1.44

(36.5)

13.3

(0.52)

ELC-PS02

POWER

L

N

24V

0V

2.36

(60.0)

3.94

(100.0)

0.12

(3.0)

1.28

(32.5)

13.3

(0.52)

3.54

(90.0)

0.12

(3.0)

2.17

(55.0)

April 2009

CA08102001E For more information visit: www.eaton.com

44-79

Distribution & Control Transformers and Power Supplies

44

Power Supplies

EZ Power Supply

Product Description

Eaton’s EZ power supplies are the

perfect products for those applications

requiring a low-amperage 24V DC

power source. While these products

were developed to be a perfect match

for our EZ Relay products, they can be

used in a variety of applications.

Features, Beneﬁts

and Functions

■Universal input voltage:

85 – 264V AC.

■Compact size, with common depth

and height across models allows for

common panel depths and family

consistency.

■EZ styling provides maximum

aesthetic appeal when used with

the Eaton EZ Relay products.

■Wide operating temperature range

(-25°C to 55°C).

■Power On indication LED.

■Optional mounting hardware for

panel mounting (EZB4-101-GF1) or

standard DIN-rail mounting.

■Finger-safe, side-entry screw clamp

terminals for clean wiring.

Standards and Certiﬁcations

■UL Listed.

■CSA Certiﬁed.

■CE Marked.

■Class I, Division II rated for groups

A, B, C, D.

■RoHS Compliant.

Product Selection

Table 44-85. EZ/EZD-CPs Power Supplies

Technical Data and Speciﬁcations

Table 44-86. Technical Speciﬁcations

Description Catalog

Number

Price

U.S. $

100 – 240V AC Input to

12V DC at 20 mA/24V DC

at 250 mA

EZ200-POW

100 – 240V AC Input to

24V DC at 1.25A

EZ400-POW

Capacity EZ200-POW EZ400-POW

6W 30W

Input

Nominal Voltage 100 – 240V AC

Voltage Range 85 – 264V AC

Frequency 47 – 63 Hz

Output

Nominal Output Voltage 24V DC +/- 3%

Nominal Current .25 A 1.25 A

General/Physical Data

Housing Material Plastic

Dimensions (D) 56.5 mm

Dimensions (W) 35.5 mm 71.5 mm

Dimensions (H) 90 mm

Operating Temperature -25°C to +55°C

Storage Temperature -40°C to +70°C

Pollution Degree 2

Connection Cables 0.2-4.0 mm^2 (AWG 22-12), Solid

0.2-2.5 mm^2 (AWG 221-12), Flexible

Approvals/Certiﬁcations

UL, CE, RoHS, CSA, EN 50178m IEC/EN 60947

Safety and Protection

Overload/Short Circuit Protection Yes

Over Current Limitation Form 0.3A 1.4A

Degree of Protection IP20

RFI Suppression EN 55011, EN 55022 Class B, IEC 61000-6-1, 2, 3, 4

Potential Isolation (prim./sec.) Yes, SELV, (to EN 600950, VDE 805)

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-80

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

EZ Power Supply

Dimensions

Figure 44-68. EZ200-POW/EZ256-HCI and EZ400-POW Series Dimensions in Inches (mm)

2.

8

1

(

71.5

)

1.41

(

35.8

)

3

.

5

4

(

90.0

)

4.

0

2

(

102.0

)

4.

33

(

110.0

)

1.

9

7

(

50.0

)

0

.42

(

10.8

)

1.77

(

45.0

)

0

.1

8

(

4.5

)

2.22

(

56.5

)

1.

8

7

(

47.5

)

(M4)

.1

5

7

(3.9)

(M4)

DIA.

0

.

30

(

7.5

)

0

.

30

(

7.5

)

1.4

0

(

35.5

)

3

.

5

4

(

90.0

)

4.

0

2

(

102.0

)

4.

33

(

110.0

)

EZ4

00

-P

OW

EZ2

56

-H

CI

EZ2

00

-P

OW

April 2009

CA08102001E For more information visit: www.eaton.com

44-81

Distribution & Control Transformers and Power Supplies

44

Power Supplies

Sensor Power Supply

Product Description

The Cutler-Hammer® Sensor Power

Supply by Eaton Corporation was

specially designed to be used with the

200 Series and E68 Series Zero Pressure

Accumulation Systems, but is also

suitable for use in a wide variety of

applications. The unit delivers 100W

output at 27V DC and supports easy,

Class II wiring. The power supply is a

tamper-proof,

rugged component eas-

ily mounted to a conveyor side-channel

or support. Internal components are

fully encapsulated in a strong die-cast

housing to stand up to rugged handling,

ensuring ﬂawless performance in any

material handling environment.

Features, Beneﬁts

and Functions

■Integrated AC junction box for one-

step mounting and wiring without

the need for additional accessories.

■Built-in DC power health contact

allows easy monitoring of power

supply status.

■Unitized design features a tamper-

proof encapsulated construction to

reduce the risk of damage associ-

ated with conventional open

control-panel type construction.

■Built-in slug-release input converts

an AC or DC input to the appropriate

DC signal for integration with the

200 Series and E68 Series Zero

Pressure Accumulation Systems.

■Dual output connection terminals

to make it easy and convenient to

locate the power supply at the

center of the cable run.

■Power switch protected against

accidental operation.

■Power in and out indicators show

status at a glance.

■Conduit entry box for NEC

compliance.

■Simple mounting with two

1/4-inch bolts.

■Rugged die-cast housing.

■Fully encapsulated electronics.

Standards and Certiﬁcations

■UL Listed.

■CSA Approved.

Product Selection

Table 44-87. Model Selection

Total output power of supply is 100W. Total supply output power (100W) = main output power + slug output power.

Stocked product, typical order quantities guaranteed in stock.

Operating

Voltage

Output Slug Input Type Slug Output Catalog

Number

Price

U.S. $

105 – 132V AC 27V DC, 100W; short

circuit, overload and

overvoltage protection

(cycle power to reset)

15 – 132V AC/DC

3 mA minimum

Standard

For use with 200 series

and E68 systems

Sinking or Sourcing, switch select-

able; 80 mA maximum; short

circuit protection for loads less

than 32V AC or DC (auto reset)

PS256A-01B1 

High Current Slug

For use with solenoid valve

systems requiring full current

slug signals

Sinking only; 100W output; short

circuit, overload and overvoltage

protection (cycle power to reset) 

PS256A-04B1 

Discount Symbol . . . . . . . . . . . . . . . . . . . . . . . . . DT-1

April 2009

44-82

For more information visit: www.eaton.com CA08102001E

Distribution & Control Transformers and Power Supplies

44

Power Supplies

Sensor Power Supply

Technical Data and Speciﬁcations

Table 44-88. Sensor Power Supply Speciﬁcations

Total output power of supply is 100W. Total supply output power (100W) = main output power + slug output power.

Dimensions

Figure 44-69. Dimensions in Inches (mm)

Wiring Diagram

Figure 44-70. Wiring Diagram

Description PS256A-01B1 PS256A-04B1

Input Power 144W, Maximum inrush 30A from cold start

Input Voltage 105 – 132V AC

Input Current (Full Load) 105V AC – 1.92A, 115V AC – 1.65A, 132V AC – 1.5A

Output Power 100W

Output Voltage 27V DC

Output Protection Short circuit, overload and overvoltage protection (cycle power to reset), diode protected

Regulation ±3%

Slug Input 15 – 132V AC/DC

Slug Output Sinking or Sourcing, switch selectable; 80 mA maximum; short

circuit protection for loads less than 32V AC or DC (auto reset)

Sinking only; 100W output; short circuit, overload and

overvoltage protection (cycle power to reset) 

Indicators Red LED: AC In; Green LED: DC Out

DC Fail Indication Output N.O. contact, solid-state relay, 80 mA maximum

Temperature Range -13° to 131°F (-25° to 55°C)

Vibration 20g

Enclosure Material Die-cast aluminum

Enclosure Rating NEMA 1

Connections Main Output/Slug Output: Two three-position ﬁnger protected barrier strips;

AC Line Input, DC Fail Indication and Slug Input: 8-position screw terminal strip inside conduit entry box

4.6

(117)

9.7

(246)

8.2

(208)

9.0

(229)

Hole for 1/4 Inch Hardware

4.6

(117)

3.0

(76)

AC Input Power

L1 L2 GND

Power Monitor

L1 L2 Not

Used

15-132 VAC/

15-132 VDC

Slug In

L1 L2

Chassis internally

connected to AC GND

V+ Slug

Output Com

V+ Slug

Output Com

Sinking Slug

Sourcing Slug

Junction

Box

PS256A-01B1 only

TB04400001E

Navigation menu

Versions of this User Manual:

Views

Navigation