Instruction_Sheet Installation Directions

323263-Installation 323263-Installation 323263-Installation 751928 Batch4 unilog cesco-content

: Pdf 323263-Installationsheet 323263-InstallationSheet 751928 Batch4 unilog

Open the PDF directly: View PDF .
Page Count: 1

Download
Open PDF In Browser	View PDF

OUTDOOR LIGHTING CONTROLS
FROM FP OLC

KNURLED NUT
MODEL
FA - 105
FA - 1068

GASKET

Installation Instructions:
1. Turn off all power at fuse or breaker box.
2. Ensure that the supply voltage matches the
NFP AND N6690/N7700 PHOTOCONTROLS
photocontrol voltage rating (see table)
3. Wire control as indicated in Figure 1.
RED
BLACK
Installation must be in compliance with NFPA
National Electrical Code which requires both
NS47671
AC SUPPLY
Cupola
STANDARD
LAMP
sides of an ungrounded single phase or
NS47673
NEUTRAL
multi-phase line be broken (article 410-48)
WHITE
SEE NOTE
(SEE TABLE)
for lighting loads.
UNGROUNDED SINGLE PHASE
4. The control should be mounted such that the
SINGLE PHASE
OR MULTI PHASE LINE
GROUNDED LINE
“photocell” faces away from artificial light
7840 SERIES N251/N252A
N L1
sources. It must not be illuminated by the
NS47681
lamp it controls or it will cycle on & off at
DPST
B
W
RELAY
NAT9021
night.
W
5. Control should be mounted with wires facing
down to prevent moisture ingress.
Figure1
N281/N282 SERIES
6. Once power is restored lamp will come on.
N271/N272 SERIES
7. Allow up to 5 minutes for lamp to turn off for
Installation
daytime operation.
Mounting:
Operation:
FA Series controls are designed for mounting in any UL approved junction box. The
All controls are designed to turn-on within a
control is provided with a neoprene gasket
range of 1-5 foot candles and turn-off within a
and one knurled nut for mounting in a wall
range of 3-15 foot candles.
plate with 11/16” center opening. The FA
The FT and SFT controls have a movable
shutter to provide for turn-on/turn-off settings.
series with post collar is provided with a self
Test:
tapping screw for grounding the post collar.
GROUND
Drill a 1/8” diameter hole into existing post
To test all controls simply cover photocell to
SCREW
FA105W
through hole in adapter and install self-tapping
simulate darkness and wait approximately 5
FA1068W
ground screw. The FT, SFT & FL series are
minutes for control to respond.
FA105P
FA1068P
designed to mount in a standard UL approved
FA - To prevent water entry into photocontrol,
always install photocontrol with wire side down
junction box.
and a drip loop on the lead wires.
Photocontrol can be mounted directly
FT15
through standard 1/2” NPT or 1/2” knockout.
FT168
Model
Line
Load Rating
Connection to junction box must be watertight
FT19
Voltage
Tungsten Ballast*
through the use of thread compound or
FT15, SFT15
120
2000W 1000VA
suitable weatherproof washer. SFT and FL
ADJUSTMENT
FT168, FFST168
208-277 2000W 1000VA
SFT15
SHUTTER
SFT168
series are provided with an elbow to allow the
FT19**, SFT19**
480
2000W 1000VA
SFT19
FL115
120
2000W 1000VA
control’s “photocell” to be directed away from
FA105,
FA105P.W
120
2000W
1000VA
ambient light sources.
FA1068, FA1068P.W 208-277

2000W

1000VA

Installation Instructions:
1. Turn off all power at fuse or breaker box.
FL115
2. Ensure that the supply voltage matches the photocontrol voltage rating (see table)
3. Wire socket as indicated in wiring diagrams shown.
4. The socket should be mounted such that the “photocell” faces away from artificial light
sources. It must not be illuminated by the lamp it controls or it will cycle on & off at night.
5. Installation must be in compliance with NFPA National Electrical Code which requires both sides
of an ungrounded single phase or multi-phase line be broken (article 410-48) for lighting loads.
6. To install the control, firmly place it into the socket and twist it clockwise until it locks into place.
7. To confirm proper control installation, during daylight hours, cover the window completely to
simulate darkness. The control should switch the load on within 1-2 minutes.
*Note: NS47671, NS47673 socket shall ne mounted directly through standard 1/2” NPT or
1/2” knockout, for NS47671, NS47673 a 1/4” NPT or 1/4” knockout, connection to junction
box must be watertight through the use of thread compound or suitable weatherproof washer.
** Not UL Listed or CSA Certified
*HID Ballast Rating

Operation:
All controls are designed to turn-on within a range of 1-5 foot candles and turn-off
within a range of 3-15 foot candles.
Control Model
FP120
FP208-277
FP480*
N7760
N7841*
N7842*
MULTI-RELAYS
N251A/N252A*
N261/N262*
N271/N272*
NS476XX
NAT9021

Line Voltage
120
208-277
420-530
120
120
208-277

Load Rating-HID
1800VA
1800VA
1800VA
1800VA
1800VA
1800VA

120
120
120
UP to 480
Up to 480

3000VA
3000VA
3000VA
15 Amps Max.
15 Amps Max.

** Not UL Listed or CSA Certified
*HID Ballast Rating

H3007

Control Model
N7762E
N7772E
N7790B
N7792E
N7793
N7794
FP240
FP240H

Line Voltage
120
240
105-285
105-285
350
480
240
240

Load Rating-HID
1800VA
1800VA
1800VA
1800VA
1800VA
1800VA
1800VA
1800VA

TYPICAL WIRING DIAGRAMS

N L1
LOAD (RED)
LINE (BLACK)

LOAD

NEUT. (WHITE)
SINGLE PHASE
GROUNDED SUPPLIES AND LOADS

UNGROUNDED SINGLE PHASE
OR MULTI PHASE LINE

SINGLE PHASE
GROUNDED LINE
N L1

R

DPST
RELAY

B
W

54 Commercial Street
54 Commercial Street
Raynham,
Raynham, MA
02767 MA 02767 USA
508-884-9732
P: 508-821-1597,
FAX: 508-822-0593
www.fisherpierceolc.com
www.fpolc.com



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:532ddb35-5cd2-11dd-a2e6-000393bcc992
Create Date                     : 2008:06:10 00:15:19Z
Metadata Date                   : 2008:07:28 14:23:49-04:00
Modify Date                     : 2008:07:28 14:23:49-04:00
Creator Tool                    : Adobe InDesign CS (3.0.1)
Rendition Class                 : proof:pdf
Derived From Instance ID        : d1147037-3812-11dd-a14f-9e546286ca10
Derived From Document ID        : adobe:docid:indd:d1147035-3812-11dd-a14f-9e546286ca10
Document ID                     : adobe:docid:indd:d1147038-3812-11dd-a14f-9e546286ca10
Manifest Link Form              : ReferenceStream, ReferenceStream
Manifest Reference Instance ID  : uuid:e90b7ac8-36a3-11dd-b32c-000393bcc992, uuid:c32fff1d-599d-11dd-ac35-000393bcc992
Manifest Reference Document ID  : uuid:c9eb9b03-b2d4-43ab-80c5-33d24a436eec, uuid:2443c59e-2bf7-11dd-b7a6-000393bcc992
Format                          : application/pdf
Title                           : Instruction_Sheet.indd
Tagged PDF                      : Yes
Trapped                         : False
Creator                         : Adobe InDesign CS (3.0.1)
Producer                        : Adobe PDF Library 6.0

EXIF Metadata provided by EXIF.tools