44661 Catalog

2014-09-27

: Pdf 44661-Catalog 44661-Catalog 685360 Batch8 unilog

Open the PDF directly: View PDF PDF.
Page Count: 44

Visit us on the web at www.marleymep.com
TABLE OF CONTENTS
2
Bathroom Ventilation 4
Environmental Series 4-5
Humidity Sensing 6-7
7000 Series 8-9
6000 Series 10-11
Decorative 12
Quick Mount 13-14
Economy 15
Compact 16
Ductless 17
Combination Fans 18
Infrared Bulb Heaters 19-20
General Home Kitchen & Utility Fans 21
Commercial and Inline Ventilators 22-25
Fire Rated Ventilators 26
Bathroom Fan Accessories 27-29
Whole House & Attic Ventilators 30
Whole House Fans 30-31
Attic Ventilators 32
Commercial Wall Fans 33
Low Profile Air Curtains 34-35
Door Chimes 36
Door Chimes and Push Buttons 36
Chime Kits 37
Bells and Buzzers & Accessories 37
Electric Heat 38
Baseboard Heaters 38-39
Wall Heaters 40
Thermostats 42
Commercial Ceiling Fans 43
Wall Mounted Speed Controls 43
Limited Warranty 43
Visit us on the web at www.marleymep.com
INTRODUCTION
Marley Engineered Products, manufacturer of Marley Builder
Products, is located in Bennettsville, SC. and offers a full line
of electric heating and ventilation products for the home and
office, providing comfort and piece of mind.
Comfort-Choose from an assortment of electric comfort
heating products. Take care of those cold spots in the house
with baseboard heaters. Warm that cold bathroom or entry-
way with a fan forced wall heater and spot heat the work
area with a radiant workshop heater.
Piece of mind-Use humidity sensing bath fans to ventilate moist air from bathrooms or ventilate the house with a
whole house fan. Protect the home from damaging heat and lessen the burden on the air conditioner with an attic
or gable ventilator. Remove harmful radon from the crawl space of your house with an inline vent and radon mitiga-
tion kit.
Products that bear the HVI Tested/Certified label have been tested at independent HVI approved laboratories and
can be depended upon to perform to the ratings shown.
Indoor fans carry dual ratings for sound output as well as ventilating performance. ventilating performance is
given in CFM (cubic feet per minute) and sound ratings are listed in sones.
A sone is an internationally recognized measurement of sound which reports decibel levels in a simplified numbered scale
which corresponds to a persons perception of loudness. The sone measurement follows a linear scale, meaning double the
number is double the perceived loudness. One sone is about the equivalent of a quiet refrigerator.
Earning the ENERGY STAR means products meet strict energy efficiency guidelines set by the US Environmental
Protection Agency and the Department of Energy.
ENERGY STAR qualified ventilation fans that include lighting use 65% less energy on average than standard models,
saving $120 in electricity costs over the life of the fan.
These fans are more than 50% quieter than standard models. They feature high performance motors and improved blade
design, providing better performance and longer life.
Choosing ENERGY STAR qualified products helps prevent global warming and promotes cleaner air.
The following logos are used throughout this catalog. Use this legend for clarification.
These products are U.L. listed by Underwriters Laboratory, ensuring that the products have passed Underwriters
Laboratory’s rigorous testing procedures for electrical products and have been assigned the listing number
required for specific electrical codes in the US and Canada.
These products are U.L. listed by Underwriters Laboratory, ensuring that the products have passed Underwriters
Laboratory’s rigorous testing procedures for electrical products and have been assigned the listing number
required for specific electrical codes in the US.
A product bearing the c ETL us Listed mark signifies that it was tested and meets the minimum requirements of
prescribed product safety standards for US and Canada. Moreover, the mark indicates that the manufacturer's
production site conforms to a range of compliance measures and is subject to periodic follow-up inspections to
verify continued conformance.
The CSA mark is recognized and accepted throughout Canada and the U.S., at federal, state, provincial, and
municipal levels. It means that the product is certified for the Canadian and US markets, and is certified to the
applicable Canadian and US standards.
Marley Bath Fans are the easiest to install. Many models feature the patented snap-in junction box cover. This
feature serves two purposes: (1) allows fan to plug directly into box; no additional wiring needed, and (2) section
snaps out quickly to allow larger area to wiring.
Designated Marley Fans can be installed in a tub or shower enclosure when wired with a GFI protected circuit.
3
INTRODUCTION
Visit us on the web at www.marleymep.com
ENVIRONMENTAL SERIES
Ultra Quiet Environmental Series
Environmental Series Bath Fan/Light Models are Energy Star qualified. By using
highly efficient motors and lighting, Energy Star bath fans can, on average, consume
65% less energy than conventional fan or fan/light models and may qualify for local
utility rebates. Learn more about Energy Star at www.energystar.gov.
The performance secrets of the 8000 Series are the heavy duty galvanized housing
fitted with high density acoustical insulation; a squirrel-cage blower designed for
optimum performance and sound properties; and a specially designed 4” duct
transition and back draft damper reduces noisy air turbulence. The high-impact
styrene grille and prism glass lens on fan/light models will complement a wide
range of decorating themes and its white color blends with most ceilings.
FEATURES
Plug-in high efficiency motor with super-quiet double
inlet blower.
New designer-styled high-impact styrene grille.
Heavy-duty galvanized housing and blower.
Four adjustable mounting bars allows for placement
anywhere between 16” O.C. and 24”O.C. ceiling joists.
High-density acoustical insulation to absorb noise.
4” duct with back draft damper reduces noisy air turbu-
lence and comes pre-assembled to housing.
cULus listed IC for use in insulated ceilings.
cULus listed for use over a tub or shower when wired
on a UL listed GFCI protected circuit.
11
3
/
16
"
10"
7
5
/
8
"
11
1
/
2
"
12
1
/
2
"
SPECIFICATIONS
HVI CERTIFIED RATINGS
ENERGY DUCT ROUGH-IN SQ. FT
MODEL STAR SIZE OPENING AMPS CFM SONES BATH OTHER
BATH VENT
8060ES Yes 4" 10-1/4” X 11-7/16” 0.20 60 0.5 55 75
8080ES Yes 4" 10-1/4” X 11-7/16” 0.26 80 1.0 75 95
8100ES Yes 4” 10-1/4” X 11-7/16” 0.29 100 1.5 95 125
8140ES Yes 4” 10-1/4” X 11-7/16” 0.40 140 2.5 130 175
8090A No 4” 10-1/4” X 11-7/16” 0.70 90 1.0 85 115
8100A No 4” 10-1/4” X 11-7/16” 0.73 100 1.5 95 125
4
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com 5
ENVIRONMENTAL SERIES
Ultra Quiet Environmental Series, Lighted
FEATURES
Plug-in high efficiency motor with super-quiet double
inlet blower.
Fluorescent models have a patented* light compartment
giving 50% more direct light from two 13-watt compact
quad-tube instant start fluorescent lamps
(bulbs included)
8190LA and 8100LA feature a 100 watt lamp and night
light (bulbs not included).
New designer-styled high-impact styrene grille with
prism glass lens for even light distribution.
Heavy-duty galvanized housing and blower.
Four adjustable mounting bars allows for placement
anywhere between 16” O.C. and 24” O.C. ceiling joists.
High-density acoustical insulation to absorb noise.
4” duct with back draft damper reduces noisy air turbu-
lence and comes pre-assembled to housing.
4-watt night light on lighted models (bulb not included)
cULus listed IC for use in insulated ceilings.
cULus listed for use over a tub or shower when wired
on a UL listed GFCI protected circuit.
* US Patent 6,939,023
SPECIFICATIONS
HVI CERTIFIED RATINGS
ENERGY DUCT LAMP ROUGH-IN SQ. FT
MODEL STAR SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT with Night Light
8060FL Yes 4" 26/4 10-1/4 X 11-7/16 0.41 60 0.5 55 75
8080FL Yes 4" 26/4 10-1/4 X 11-7/16 0.48 80 1.0 75 95
8100FL Yes 4” 26/4 10-1/4 X 11-7/16 0.51 100 1.5 95 125
8140FL Yes 4” 26/4 10-1/4 X 11-7/16 0.62 140 2.5 130 175
8090LA No 4” 100/7 10-1/4”X11-7/16” 1.5 90 1.0 85 115
8100LA No 4” 100/7 10-1/4”X11-7/16” 1.5 100 1.5 95 125
12 1/2"
12 1/2"
11 3/16"
10"
7 5/8"
Patented Light Compartment
50% more direct light - Bulbs included.
(Models 8060FL, 8080FL, 8100FL, 8140FL)
BATHROOM VENTILATION
ENVIRONMENTAL SERIES
Visit us on the web at www.marleymep.com
6
Humidity Sensing
Bath fans using the Aware Technology constantly monitor the humidity level of the
bathroom, and turn on and off automatically. Both humidity level and time of opera-
tion are easily adjustable.
1Steam from shower or
bath turns on fan auto-
matically
2Bath Fan quickly removes
damaging steam and mois-
ture
3When damaging steam
and moisture are removed,
Bath Fan turns off
automatically
Visit us on the web at www.marleymep.com 7
ENVIRONMENTAL SERIES
HVI CERTIFIED RATINGS
ENERGY DUCT LAMP ROUGH-IN SQ. FT
MODEL STAR SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT with Night Light
8100FLH Yes 4” 26/4 10-1/4 X 11-7/16 0.51 100 1.5 95 125
BATH VENT
8100ESH Yes 4” 10-1/4 X 11-7/16 0.29 100 1.5 95 125
SPECIFICATIONS
12 1/2"
12 1/2"
11 3/16"
10"
7 5/8"
12
1/2"
12 1/2"
FEATURES
Plug-in high efficiency motor with super-quiet double
inlet blower.
Lighted models have a patented* light compartment
giving 50% more direct light from two 13-watt compact
quad-tube instant start fluorescent lamps
(bulbs included)
New designer-styled high-impact styrene grille with
prism glass lens for even light distribution.
Heavy-duty galvanized housing and blower.
Four adjustable mounting bars allows for placement
anywhere between 16” O.C. and 24”O.C. ceiling joists.
High-density acoustical insulation to absorb noise.
4” duct with back draft damper reduces noisy air turbu-
lence and comes pre-assembled to housing.
Built-in Humidity Sensor automatically detects humidity
and turns on fan. Manual override from wall switch.
4-watt night light on lighted models (bulb not included)
cULus listed IC for use in insulated ceilings.
cULus listed for use over a tub or shower when wired
on a UL listed GFCI protected circuit.
Energy Star qualified.
* US Patent 6,939,023
8100FLH
8100ESH
Patented Light Compartment
50% more direct light - Bulbs included.
(Model 8100FLH)
BATHROOM VENTILATION
7000 SERIES
Visit us on the web at www.marleymep.com
8
FEATURES
Plug-in enclosed motor with super-quiet centrifugal
blower wheel.
High-impact styrene grille.
4” Duct adapter with integral back draft damper reduces
air turbulence and comes pre-assembled to housing.
Computer designed air chamber for optimum air flow
and sound properties.
Adjustable mounting brackets for easy installation
between ceiling joists.
U.L. listed type IC for use in insulated ceilings.
Can be used in tub or shower enclosure when
wired on a U.L. listed GFCI protected circuit.
HVI CERTIFIED RATINGS
DUCT ROUGH-IN SQ. FT
MODEL SIZE OPENING AMPS CFM SONES BATH OTHER
BATH VENT
7100A 4” 10-1/4” X 11-7/16” 0.70 100 1.5 95 125
7150A 4” 10-1/4” X 11-7/16” 1.7 150 3.5 140 190
SPECIFICATIONS
7100 Series Bath Fans
The high-impact styrene grille will complement a wide range of decorating themes
and its white color blends with the ceiling as a subtle styling addition. The computer
designed air chamber provides optimum air flow and sound properties; and super-
quiet centrifugal blower wheel for maximum ventilation. These fans are U.L. listed
and can be used over a tub or shower enclosure when installed on a GFCI protect-
ed circuit.
11
3
/
16
"
10"
7
5
/
8
"
11
1
/
2
"
12
1
/
2
"
Visit us on the web at www.marleymep.com 9
7000 SERIES
FEATURES
Plug-in enclosed motor with super-quiet centrifugal
blower wheel.
High-impact styrene grille with snap in Lexan® lens.
Lighted models have 100 Watt lamp capacity
(lamp not included).
7 1/2 Watt night light on lighted models
(lamp not included).
4” Duct adapter with integral back draft damper reduces
air turbulence and comes pre-assembled to housing.
Computer designed air chamber for optimum air flow
and sound properties.
Adjustable mounting brackets for easy installation
between ceiling joists.
U.L. listed type IC for use in insulated ceilings.
Can be used in tub or shower enclosure when wired on
a U.L. listed GFCI protected circuit.
7100 Series Bath Fans, Lighted
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT WITH NIGHT LIGHT
7100LA 4” 100/7 10-1/4”X 11-7/16” 1.5 100 1.5 95 125
7150LA 4” 100/7 10-1/4”X 11-7/16” 2.5 150 3.5 140 190
SPECIFICATIONS
12 1/2"
12 1/2"
11 3/16"
10"
7 5/8"
BATHROOM VENTILATION
6000 SERIES
Visit us on the web at www.marleymep.com
10
6000 Series Bath Fans
Marley Engineered Products 6000 Series Bath Fans are intended for use in bath-
rooms but can be used in other ares where ventilation is required. These models
feature efficient Marley Engineered Products designed motors combined with spe-
cially designed squirrel-cage blowers. All Bath Fans are U.L. listed type I.C.
(Inherently Protected) for installation in insulated ceilings and above a bathtub or
shower when connected to a U.L. listed GFCI protected branch circuit.
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT
6060 4” 8-3/4” X 8-3/4” 1.2 60 4.0 55 75
6080 4” 8-3/4” X 8-3/4” 0.7 80 3.0 75 95
6100 4” 8-3/4” X 8-3/4” 0.7 110 4.0 105 135
BUILDER SPLIT PACKS
6000X1 BUILDER SPLIT PACK - HOUSING 6 PACK
6060X2 BUILDER SPLIT PACK - FINISH PACK (1) 60CFM VENT ONLY
6080X2 BUILDER SPLIT PACK - FINISH PACK (1) 80CFM VENT ONLY
6100X2 BUILDER SPLIT PACK - FINISH PACK (1) 110CFM VENT ONLY
8
1/2"
10"
8
1/2"
10"
10"
10"
5 3/8"
FEATURES
Low profile grille assembly
4” round discharge with automatic back draft damper
Built-in mounting bracket
Large, easily accessible outlet box
Easy installation in new or existing ceilings
Builder Split Pack available
6060
Visit us on the web at www.marleymep.com 11
6000 SERIES
6000 Series Bath Fans, Lighted
Marley Engineered Products 6000 Series Bath Fans are intended for use in bath-
rooms but can be used in other ares where ventilation is required. These models
feature efficient Marley Engineered Products designed motors combined with spe-
cially designed squirrel-cage blowers. All Bath Fans are U.L. listed type I.C.
(Inherently Protected) for installation in insulated ceilings and above a bathtub or
shower when connected to a U.L. listed GFCI protected branch circuit.
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT
6060RL 4” 100 8-3/4” X 8-3/4” 2.1 60 4.0 55 75
6080RL 4” 100 8-3/4” X 8-3/4” 1.7 80 3.5 75 95
6100RL 4” 100 8-3/4” X 8-3/4” 1.7 110 4.0 105 135
BUILDER SPLIT PACKS
6000X1 BUILDER SPLIT PACK - HOUSING 6 PACK
6060RLX2 BUILDER SPLIT PACK - FINISH PACK (1) 60CFM VENT/LIGHT
6080RLX2 BUILDER SPLIT PACK - FINISH PACK (1) 80CFM VENT/LIGHT
6100RLX2 BUILDER SPLIT PACK - FINISH PACK (1) 110CFM VENT/LIGHT
8
1/2"
8
1/2"
10"
10"
10"
5 3/8"
FEATURES
Low profile grille assembly
Lighted models have 100 watt lamp capacity (lamp
not included)
Unbreakable Lexan® lens (lighted models) snaps on
and off for easy bulb replacement
4” round discharge with automatic back draft damper
Built-in mounting bracket
Large, easily accessible outlet box
Easy installation in new or existing ceilings
Builder Split Pack available
6060RL
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com
DECORATIVE
12
Decorative Bath Fans
These attractive ceiling units combine even, diffused lighting and quiet ventilation.
A full 14 inches in diameter, this round design is pleasing in rooms where a tradi-
tionally shaped fixture is not aesthetically correct. These powerful ventilators draw
mildew-building moisture from the room through a 4 inch round discharge. Model
1001 provides 100 CFM ventilation for bathrooms up to 95 sq. ft.
FEATURES
Low profile round grille with Lexan® lens.
100 Watt Lamp Capacity (Lamp not included).
4” round duct adapter with integral back draft
damper.
Adjustable mounting brackets for easy instal-
lation between ceiling joists (16” O.C. or 24”
O.C.)
Plug-in light reflector assembly.
Large, easily accessible outlet box.
Low profile housing installs between 6” floor
joists.
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL FINISH SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT
1001 WHITE 4” 100 12-3/4” DIA 1.65 100 4.5 95 125
1001
Visit us on the web at www.marleymep.com 13
ECONOMY QUICK MOUNT BATH FANS
Simply position the housing and drive the
positioned mounting screws securely.
Connect the ducting and install the spring fitted
grill and the job is finished.
The Quick-Mount system holds and positions the
integral mounting screws on the sturdy steel
housing.
Snap out the patented outlet box and connect
the wiring. Rough in work is complete!
Quick Mount Bath Fans
Installation has never been easier.
Models A647B and MM647B offer the ultimate combination of economy and innova-
tion. A new patent-pending Quick-Mount installation system helps reduce labor
costs. Now a bath fan installation can be done in minutes. The Quick-Mount system
holds and positions the integral mounting screws on the sturdy steel housing.
Simply position the housing against the ceiling joist using the stamped indicator
marks and drive or screw the pre-positioned mounting screws securely. Snap-out
the patented outlet box and connect the wiring. Connect the ducting and install the
spring fitted grille and the job is finished.
BATHROOM VENTILATION
ECONOMY QUICK MOUNT BATH FANS
FEATURES
Patent-Pending quick mount installation system
holds and positions mounting screws (included)
in place while housing is being installed.
Patented “Snap-in” outlet box and reversible
knock pad.
Plug-in motor with sturdy polypropylene impeller.
Pre-assembled 3” duct adapter with back draft
damper.
Choice of 2-low profile spring mounted High-
Impact styrene grilles.
cULus Listed IC for use in insulated ceiling.
cULus Listed for use over a tub or shower when
wired on a cULus Listed GFI protected circuit.
HVI 2100 certified.
Builder split-packs (separate housing and finish-
ing packs) available. Models A647BX1 housing
pack and A647X2 or MM647X2 finish packs.
HVI CERTIFIED RATINGS
DUCT ROUGH-IN SQ. FT
MODEL SIZE OPENING AMPS CFM SONES BATH OTHER
BATH VENT
A647B 3” 6-7/8”X7-7/8” .89 50 4.5 45 65
MM647B 3” 6-7/8”X7-7/8” .89 50 4.5 45 65
BUILDER SPLIT PACKS
A647BX1 BUILDER SPLIT PACK - HOUSING 6 PACK
A647BMX1 BUILDER SPLIT PACK - HOUSING 6 PACK WITH METAL DUCT ADAPTER.
A647X2 BUILDER SPLIT PACK - FINISH 6 PACK (USE WITH A647BX1 OR A647BMX1)
MM647X2 BUILDER SPLIT PACK - FINISH 6 PACK (USE WITH A647BX1 OR A647BMX1)
SPECIFICATIONS
Contractors will appreciate the time saving benefits of the new Patent Pending Quick
Mount installation system. Builder Split Packs available.
A647B
MM647B
14 Visit us on the web at www.marleymep.com
Economy Bath Fans
Models MM648 and MM748 offer long-lasting performance and attractive appear-
ance at an economical price. The Bath Fans are intended for use in bathrooms, but
can be used in other areas where ventilation is required.
A664IC Bath Vents are compact and easy to install. The vent and light may be sep-
arately switched for vent only, light only or vent plus light operation.
FEATURES
MM648 & MM748
Heavy-duty steel housing
Built-in mounting bracket and junction
box
Attractive white elliptical grille
Round duct
Plug-in motor
Use with conventional wall switch or
timer
FEATURES
A664IC
Ventilator and light combinations are
compact and simple to install
Can be separately switched for vent only,
light only, or vent plus light
Unbreakable Lexan® lens snaps out of
the grille for easy cleaning
Attractive 9” x 10” plastic grille
4” round duct connection and hinged
back draft damper
UL listed for use in insulated ceilings
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT
MM648 3” NA 6-7/8” X 7-7/8” .89 60 3.5 55 75
MM748 4” NA 6-7/8” X 7-7/8” 1.1 70 5.0 65 85
BATH VENT / LIGHT
A664IC 4” 100 6-7/8”X7-7/8” 1.70 50 3.5 45 65
A664ICX1 BUILDER SPLIT PACK - HOUSING 6 PACK
A664ICX2 BUILDER SPLIT PACK - FINISH 6 PACK
7 3/4"
6 1/4"
6 3/4"
12 5/16"10 3/4"
MM648
MM748
A664IC
15
Visit us on the web at www.marleymep.com
ECONOMY QUICK MOUNT BATH FANS
BATHROOM VENTILATION
ECONOMY BATH FAN/LIGHT
16
Compact Bath Fans
MM664IC, MM667IC and MM667ICF Bath Fans are compact and easy to install.
The vent and light may be separately switched for vent only, light only or vent plus
light operation. The Bath Fans are intended for use in bathrooms, but can be used
in other areas where ventilation is required. All models are U.L. listed Type I.C.
(Inherently Protected) for installation in insulated ceilings. These units are approved
for installation in the ceiling above a bathtub or shower stall only when connected to
a U.L. listed GFCI protected branch circuit.
FEATURES
Ventilator and light combinations are compact and simple
to install
Model MM667ICF uses energy efficient 13 watt compact
twin tube fluorescent lamp (not included)
Can be separately switched for vent only, light only, or
vent plus light
Unbreakable Lexan® lens snaps out of the grille for easy
cleaning
Attractive white elliptical grille
4” round duct connection and hinged back draft damper
Listed for use in insulated ceilings
Builder Split Packs available
12 5/16"10 3/4"
7 3/4"
6 1/4"
6 3/4"
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT
MM667ICF 4” 13 6-7/8”X7-7/8” 1.45 70 4.0 65 85
MM664IC 4” 100 6-7/8” X 7-7/8” 1.7 50 4.0 45 65
MM667IC 4” 100 6-7/8” X 7-7/8” 1.93 70 4.0 65 85
MM664ICX2 BUILDER SPLIT PACK - FINISH 6 PACK (USE WITH A664ICX1)
E667ICFX1 BUILDER SPLIT PACK - HOUSING 6 PACK
MM667ICFX2 BUILDER SPLIT PACK - FINISH 6 PACK
Visit us on the web at www.marleymep.com
DUCTLESS
Ductless Bath Fans
Models 645 and 646 ductless ventilators are perfect for applications where running duct work
would be unnecessary or impractical. Easy to install these units provide an affordable alterna-
tive to ducted fans.
FEATURES
645
Air is circulated through a carbon filled, non-woven
polyester filter
Replaceable filter
No ducts to install
Plug-in motor
Radial impeller for quiet operation
Integral mounting brackets for quick, simple installa-
tion
Plaster depth gauge for flush mounting
Pre-wired junction box with wiring knockouts
Use with conventional wall switch or with timer
646
Same features as Model 645 with the addition of:
• Built-in light; 100 watt max (lamp not included)
SPECIFICATIONS
LAMP ROUGH-IN
MODEL FINISH WATTS OPENING AMPS CFM
BATH VENT / LIGHT
645 WHITE N/A 7-1/8”X9” .89 70
646 WHITE 100 7-7/8”X7-7/8” 1.7 70
645
646
17
Visit us on the web at www.marleymep.com
BATHROOM VENTILATION
COMBINATION FANS
18
Combination Bath Fans
Designer elliptical grille, with integral light, blends beautifully with any décor. This
“All in One” model offers light, ventilation and heat which can be operated singly, or
in any combination. Models MM698WC and MM728NL include a color matched,
pre-wired, single gang wall control and model MM 728NL also features a night
light. Designed to accommodate installation between 2 x 6” ceiling joist, they are
available in either 70 CFM or 100 CFM for ventilation and deliver 1500 watts of
instant fan-forced heat. Bath Fans are intended for use in bathrooms, but can be
used in other areas where ventilation is required.
FEATURES
Two separate motors - one for heating and one
for ventilation
MM698F uses energy efficient 13 watt compact
twin tube fluorescent lamp ( not included)
Heat unit delivers 1500 watts of instant heat with
thermal protection
Attractive white elliptical grille
UL Listed Type IC for use in insulated ceilings
Unbreakable Lexan® lens diffuses light from
maximum 100 watt lamp and model MM728NL
also features a night light
All components are independent plug-in units
Adjustable mounting brackets for easy installation
between ceiling joist
MM728NL & MM698-WC come with two-rocker
wall switch control (single gang)
Two-toggle bath fan control
• White
Wall plate not included
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / LIGHT / HEATER
MM698F 4” 13/7-1/2 8”X14-5/16” 13.44* 70 3.0 65 90
MM698 4” 100 8”X14-5/16” 13.8* 70 3.0 65 90
MM698WC 4” 100 8”X14-5/16” 13.8* 70 3.0 65 90
MM728NL 4” 100/7-1/2 8”X14-5/16” 13.8* 100 5.5 95 125
MM698X1 BUILDER SPLIT PACK - HOUSING 4 PACK
MM698AX2 BUILDER SPLIT PACK - FINISH PACK (1)
*INCLUDES HEATER AND VENT / LIGHT
Visit us on the web at www.marleymep.com
Visit us on the web at www.marleymep.com 19
INFRARED HEATERS
FEATURES
B674W
Instantly provides up to 750 watts of gentle heat
Uses two R-40 lamps up to 375 watts (2560 BTU)
Wired for switch, timer or single pole thermostat oper-
ation
Easy installation with mounting to either 16” or 24”
O.C. joists with rigid,
4-point mounting system
Use with conventional wall switch or timer
UL Listed I.C. for insulated ceilings
A564
Up to 375 watt, R-40 infrared heat lamp provides
instant warmth (lamp not included)
Inside reflective lamp surface that directs gentle heat
rays downward
Spring loaded, easy-on, easy-off grille
Easy four-point mounting system installation
Junction box easy to access
Use with conventional wall switch
UL Listed I.C. for insulated ceilings
Bulb Heaters
Bulb Heaters will turn the coldest, most damp bathroom into a warm comfort zone.
with instant heat. These heaters provide warmth through the use of infrared heat
lamps. Model B674W uses two R-40 lamps
SPECIFICATIONS
DUCT LAMP ROUGH-IN
MODEL SIZE WATTS OPENING AMPS
INFRARED BULB HEATER
A564 N/A 375 8-1/2”X9-1/4” 3.33
B674W N/A 750 8-1/2”X14-5/16” 6.5
A564
B674W
BATHROOM VENTILATION
INFRARED HEATERS
Visit us on the web at www.marleymep.com
20
FEATURES
B660W
70CFM of ventilation
4” duct adapter
Long life, permanently lubricated, shaded pole motor
Large venturi assures quiet, efficient ventilation
Uses two R-40 lamps up to 375 watts (2560 BTU)
UL Listed I.C. for insulated ceilings
B560
70 CFM of ventilation
Spring loaded, easy-on, easy-off grille
Easy four-point mounting system installation
Junction box easy to access
Use with conventional wall switch
4” duct adapter with back draft damper
Long life permanently lubricated motor
UL Listed I.C. for insulated ceilings
Uses one R-40 lamp up to 375 watts
Bulb Heaters / Bath Fans
Bulb Heaters will turn the coldest, most damp bathroom into a warm comfort zone.
with instant heat. These heaters provide warmth through the use of infrared heat
lamps. Model B674W uses two R-40 lamps
B660W
B560
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT LAMP ROUGH-IN SQ. FT
MODEL SIZE WATTS OPENING AMPS CFM SONES BATH OTHER
BATH VENT / BULB HEATER
B560 4” 375 8-1/2”X9-1/4” 4.11 70 5.5 65 85
B660W 4” 750 8-1/2”X14-5/16” 7.35 70 4.0 65 85
Visit us on the web at www.marleymep.com 21
HOME & KITCHEN
General Home / Kitchen Fans / Utility Fans
Marley Builder Products’ through the wall General ventilators provide a simple cost effective
method of controlling temperature levels throughout the home.
FEATURES
790L
Room-to-room ventilator equalizes temperature levels
throughout the home
Especially effective in homes with fireplaces and window
air conditioners
Built-in switch with solid state speed control
Plug-in motor and blade assembly for ease in installation
898L / 899L
Kitchen ventilator exhausts heat and moisture-laden air
directly outside with no ductwork
Rustproof, weather-resistant exterior parts
Powerful, deep-pitched blades
Plug-in motor and blade assembly
Switch operated; use with conventional wall switch or
timer
Pull-chain operated (899L)
1047
• 10” heavy-duty, through-the-wall ventilator for larger
kitchens
• Pull-chain operated
• Positive close door
760L
Vertical discharge ceiling ventilator
Quickly exhausts contaminated air to the outdoors
Use to ventilate large areas such as workshops, utility
rooms, etc.
Compact, one-piece housing with back draft damper
Adjustable mounting brackets
All steel grille
Use with conventional wall switch or timer
1080
A larger, more powerful version of the 760L
• Deep-pitch 10” blades
• Vertical exhaust
• Plug-in motor
Adjustable mounting tabs
790L
898L
1047
899L
SPECIFICATIONS
ROUGH-IN WALL DUCT
MODEL FINISH OPENING AMPS CFM SONES THICKNESS SIZE
HOME / KITCHEN VENTILATORS
790L WHITE 9” 1.1 250 3-1/2” TO 6-1/2” -
898L WHITE 9” 1.2 200 7.0 4-1/4” TO 8” -
899L WHITE 9” 1.2 200 7.0 4-1/4” TO 8” -
1047 WHITE 11” .90 460 7.0 4-1/4” TO 8-1/4” -
UTILITY FANS
760L WHITE 7” 1.1 200 5.5 - 9” DIA. DUCT
1080 WHITE 11” .90 280 5.5 - 11” DIA. DUCT
760L
1080
BATHROOM VENTILATION
22 Visit us on the web at www.marleymep.com
COMMERCIAL VENTILATORS
Super QTM Ventilators
All Super Q™ commercial ventilators can be
converted for either In-Line or Direct Discharge
applications.
SUPER PERFORMANCE RANGE
6 models to cover ventilation requirements from the
smallest baths to the largest conference rooms
Range from 101 CFM to 855 CFM (.125" S.P.)
Range from 123 CFM to 910 CFM (0.0" S.P.)
SUPER QUIET VENTILATION
Large centrifugal blowers rotate slowly to generate
airflow with exceptional quietness. The Super-Q
ventilators operate at 1550 RPM or less. Other fans
run at speeds up to 3600 RPM.
Motors float in resilient rubber mountings, eliminat-
ing vibration
Chatter proof integral backdraft damper
SUPER HEAVY-DUTY CONSTRUCTION
Heavy gauge steel housing with sound absorbing,
1/2" acoustic insulation lining the housing
Permanently lubricated motor designed for continu-
ous operation
Factory-balanced blower wheels and motors; all
components tested prior to shipment
SUPER FLEXIBILITY
All models can be mounted for direct discharge or
converted for In-Line discharge
Models CV6, CV8, and CV10 have 2-speed motors
to cover additional ventilation requirements
IN-LINE VENTILATION
Remote power units provide high volume air
movement quietly. Super Q™ Ventilators can
be used throughout normal heating and air con-
ditioning systems in homes and offices. Multiple
rooms may be ventilated with high volume air
movement.
DIRECT DISCHARGE VENTILATION
Commercial and industrial construction requires
positive, high-performance ventilation. Building
code requirements, the health and comfort of
building occupants, and the protection of stored
goods all mandate specific periodic changes of
air in the following:
Public Buildings
Commercial Buildings
Institutional Buildings
High-Rise Structures
Other Residences
For applications where residential
grade ventilators aren’t enough, use Marley
Builder Products’ specification-grade ventila-
tors.
The Super Q™ Series – super performance . . .
super quiet . . . in a word – superlative.
TM
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com 23
COMMERCIAL VENTILATORS
STATIC PRESSURE (IN. OF W.G.)
CU. FT. PER MIN. (THOUSANDS)
0.2.4.6.81.01.2
.25
.50
.75
1.00
1.25
1.50
CV6
CV10
CV8
CV12
STATIC PRESSURE (IN. OF W.G.)
CU. FT. PER MIN. (THOUSANDS)
0.2 .4 .6 .8 1.0 1.2
.25
.50
.75
1.00
1.25
1.50
CV6
CV8
CV10
CV12
DIRECT DISCHARGE APPLICATIONS IN-LINE APPLICATIONS
MOTOR MAX. FAN CAPACITY - CUBIC FEET PER MINUTE3
MOTOR1VOLTAGE WATTS WEIGHT STATIC
MODEL RPM 60 Hz A.C. INPUT (Lbs.) PRESSURE 0” .125” .250” .375” .500” .625” .750”
CFM4123 101 82 - - - -
CV6 Low Speed 1050 115/1 47 14 SONES20.9 1.4 1.8 - - - -
CFM4230 196 166 122 - - -
CV6 High Speed 1550 115/1 108 14 SONES23.3 3.0 3.0 3.1 - - -
CFM4272 247 231 217 199 - -
CV8 Low Speed 1050 115/1 77 20 SONES22.1 2.4 2.9 3.3 3.6 - -
CFM4426 401 377 357 341 328 304
CV8 High Speed 1550 115/1 130 20 SONES24.5 4.7 4.7 5.1 5.6 5.8 5.8
CFM4469 441 423 403 387 367 347
CV10 Low Speed 1050 115/1 243 30 SONES24.5 4.8 5.1 5.4 5.6 5.8 6.0
CFM4728 694 664 638 613 591 565
CV10 High Speed 1550 115/1 390 30 SONES28.6 8.6 8.6 8.7 8.6 8.8 8.8
CFM4901 855 812 755 683 552
CV12 1050 115/1 260 44 SONES25.8 5.9 6.3 6.5 6.5 6.0
SUPER Q™ FAN PERFORMANCE
HOUSING OUTLET GRILL TDA PANEL
MODEL A B C D E E1 F G H J K L X Y Z
CV6 12.25 9.125 16 9.125 1.25 1.25 5.375 10 3.25 0.75 11 13.75 10 6 1.625
CV8 13.875 11.375 17.375 11.375 1.87 4 5.25 8 6 0.75 13.25 14.875 10 8 1.563
CV10 18 14.125 21.5 14.125 3.625 6.375 8 8 6 0.75 15.5 19.375 14 10 2
CV12 24 14.125 27.5 14.125 1 1 8 22 6 0.75 15.5 25 20 10 2
FAN DIMENSIONS
Units are shipped with motor connected for “S” (low speed) operation.
(1) RPM shown is nominal and the performance is based on actual speed of test
(2) Sones ratings in accordance with AMCA Standard 301-90
(3) The AMCA Certified Ratings Seal applies to air capacities only
(4) Performances shown include values with inlet grill, backdraft damper and outlet duct in
place
CV6, CV8, CV81, CV12 Alternate Mounting
CV10, CV101 Flange Position TDA Panel
Grill
Visit us on the web at www.marleymep.com
INLINE VENTILATORS
24
Inline Ventilators
Marley Engineered Products remote mounted
In-Line ventilation fans are both quiet and high
performance. In-line fans generate two to
three times the pressure of conventional fans
and provide the airflow needed to overcome
system resistance caused by long duct runs
and multiple in-take vents.
FEATURES
• Ultra quiet remote mounted.
• Energy-efficient permanently lubricated motor.
• Backward curved centrifugal fan.
• Rated for continuous or intermittent operation.
• Rated for commercial and residential applications.
• HVI 2100 certified and cETLus Listed.
Accessories available separately.
IF110
IF275
IF400
IF500
HVI CERTIFIED RATINGS @ 0.2 E.S.P.
DUCT 120VAC, 60HZ "A" "B" "C" SQ. FT
MODEL SIZE (2.0 AMP MAX.) DIM DIM DIM CFM BATH OTHER WT
IF110 4" 14-19 watts 9.7" 3.9" 8.5" 100 95 125 5.0
IF275 6" 52-73 watts 11.8" 5.9" 8.6" 230 210 290 5.5
IF400 8" 103-156 watts 13.4" 7.9" 9.0" 470 430 590 9.0
IF500 10" 103-156 watts 13.4" 9.9" 9.0" 460 420 575 9.0
SPECIFICATIONS
Visit us on the web at www.marleymep.com 25
INLINE VENTILATORS
FEATURES
• Ultra quiet remote mounted.
• Energy-efficient permanently lubricated motor.
• Backward curved centrifugal fan.
• Rated for continuous or intermittent operation.
• Rated for commercial and residential applications.
• HVI 2100 certified and cETLus Listed.
Accessories available separately.
FEATURES
• Ultra quiet remote mounted.
• Energy-efficient permanently lubricated motor.
• Backward curved centrifugal fan.
• Rated for continuous or intermittent operation.
• Rated for commercial and residential applications.
• HVI 2100 certified and cETLus Listed.
Accessories available separately.
IF110DK
IF175RK
HVI CERTIFIED RATINGS @ 0.2 E.S.P.
DUCT 120VAC, 60HZ "A" "B" "C" SQ. FT
MODEL SIZE (2.0 AMP MAX.) DIM DIM DIM CFM BATH OTHER WT
IF110DK 4" 14-19 watts 9.7" 3.9" 8.5" 100 95 125 5.2
HVI CERTIFIED RATINGS @ 0.2 E.S.P.
DUCT 120VAC, 60HZ "A" "B" "C" SQ. FT
MODEL SIZE (2.0 AMP MAX.) DIM DIM DIM CFM BATH OTHER WT
IF175RK 6" 49-65 watts 8.5" 5.9" 9.5" 170 155 215 10.0
Dryer Boost Kit Model IF110DK:
A clothes drying system with long duct runs or multiple bends will result in longer drying time
and excess wear on the dryer. Adding an auxiliary fan with an automatic pressure switch to the
dryer duct system will increase airflow resulting in reduced drying time and less energy
consumption. Automatic pressure switch included in kit.
Radon Mitigation Kit Model IF175RK:
Specifically designed for Radon Mitigation and extremely effective for sub-slab systems, Model
IF175RK is ultra quiet and is suitable for wet environments. Kit includes all hardware needed
to easily connect fan to 4" PVC pipe. Kit includes: RV175 fan (qty 1), 4" x 6" Flexible Coupling
(qty 2), Manometer (qty 1), System Label (qty 1) and Component Label (qty 2) and instructions.
Warning: Kit should only be installed by qualified Radon Mitigators.
SPECIFICATIONS
SPECIFICATIONS
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com
FIRE RATED VENTILATORS
26
Fire Rated Bathroom Ventilators
Model 650FRD, 680FRD, and 610FRD with built-In Fire Radiation Damper, offers
the ultimate combination of quiet high performance ventilation and the best
protection against flame penetration and radiant heat. Marley Engineered Products
fans are intended for use in bathrooms, but can be used in other areas where
ventilation is required.
SPECIFICATIONS
HVI CERTIFIED RATINGS
DUCT ROUGH-IN SQ. FT
MODEL SIZE OPENING AMPS CFM SONES BATH OTHER
BATH VENT
650FRD 3” 8-1/4” X 9-1/4” 0.76 50 2.5 45 65
680FRD 4” 8-1/4” X 9-1/4” 0.35 80 2.5 75 95
610FRD 4” 8-1/4” X 9-1/4” 0.60 100 3.0 95 125
FEATURES
Rugged, 22-gauge plated steel housing with
pre-mounted 4” round steel duct fitting with
built-in backdraft damper (3" on 650FRD).
Plug-in totally enclosed permanently lubricated
motor
Spring-mounted white painted low-profile steel
grille
Mounting brackets included for installation
between ceiling joists or in drop ceilings
UL/cUL listed and HVI certified
DAMPER CONSTRUCTION
22-gauge galvanized steel frame
Pre-mounted 4” duct adapter with damper
Stainless steel closure springs
High heat, non-asbestos ceramic blanket
Replaceable 165 Fº fusible link
(Others available)
UL/cUL listed ceiling firestop damper
Designed and tested in accordance with cUL
Guide No. 40U18.1.1-1/2
Up to three hours fire resistance rating
8 1/4"9 1/4"
7"
10 3/8"
9
1/2"
9/16
Visit us on the web at www.marleymep.com 27
ACCESSORIES
Vent Accessories
From roof caps to wall caps, timers to 3-toggle controls, our large line of bath fan accessories
provide all you need to assemble and connect your bath fan in perfect working order. We even
provide the added convenience of purchasing single items or kits in certain configurations for
simple installation.
1222
• Dehumidistat control
• Use for humidity control
with bath fans
• 120VAC/ 7.5 Amps
• 240VAC/ 3.75 Amps
AD627A
• Two-toggle bath fan control
• White
• Wall plate not included
AD628A
• Three-toggle bath fan control
• White
• Wall plate not included
AD1114, AD1116, & AD1118
• Diffusers for 4” (AD1114), 6” (AD1116)
and 8” (AD1118) round ducts
• Ideal for central ventilation, cooling,
and heating; fully adjustable
• Anti-static additives keep the diffuser
dust free
1010A &1011A
• Model 1010A is a five minute timer
• Model 1011A is a one-hour timer
• Use with all bath fans and whole
house fans
1230
• Line voltage cooling
thermostat
• Range 60°-120°F
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com
ACCESSORIES
28
AD1105
• Roof cap for 3” or 4” duct
AD1107
• Flexible 7” x 8’ aluminum duct
AD1109
• 4” x 8’ flexible aluminum duct
AD1106
• Roof cap for up to 7” duct
AD1102
• Roof cap kit
• Includes roof cap, 3” and
4”duct connector, 4” x 8'
flexible vinyl duct and
plastic clamps
AD1103
• Wall cap kit
• Includes wall cap, 3”
and 4” duct connector,
4” x 5” flexible vinyl duct
and plastic clamps
Visit us on the web at www.marleymep.com 29
ACCESSORIES
1117A
• Wall cap for 3” or
4” round duct
1125
• Wall cap for 3-1/4” x 10” duct
IFD4, IFD6, IFD8 & IFD10
• Backdraft dampers for inline
fans
• Fits 4” (IFD4), 6” (IFD6),
8” (IFD8) and 10” (IFD10)
round ducts
IFY6 & IFY8
• Metal Y connectors for inline
fans
• Fits 6” (IFY6) and 8” (IFY8)
round ducts
1245
• Thermal safety
cutout
• Opens at 165°F
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com
WHOLE HOUSE FANS
30
A20DD
• Ideal for today’s smaller, energy-
efficient homes
• Fan housing has a steel telescoping
sleeve, eliminating wood framing
• Handy three-speed pull chain
switch
• All steel housing with baked enamel
finish
• Extra deep housing designed for
today’s deeper insulation needs
• Dynamically balanced aluminum
blades
• Permanent split capacitor motor
• Direct drive for consistent, low
maintenance operation
• Equipped with shutter
A24DD
• Easy installation in 16” O.C.
(some framing required for 24”
O.C.); No joist cutting required
• Adjustable side panels form a
plenum
• Three-speed direct drive motor
with wall mounted control included
• Deep venturi for quiet operation
and maximum performance
• Four blades for maximum airflow;
cools or ventilates a large home
• Thermal overload protection for
maximum safety
Whole House Fans
are engineered to cool and ventilate the entire house. Hot humid air is expelled outdoors and cool fresh air is
pulled into the living areas. Airflow can be directed by opening and closing windows throughout the home. By
choosing proper fan speed, your living area is quickly and economically cooled for maximum comfort.
Designed for mounting on 24" or 16" O.C. joists, several models require no framing.
All Whole House Fans have pull chain or wall speed controls included.
SPECIFICATIONS
SHUTTER CLEAR CEILING
MODEL CFM RPM AMPS SIZE OPENING SPACE REQUIRED
A20DD 3400 1050 3.0 24”x28” 22”x26” 24”x28”
A24DD 5500 1065 5.1 30-1/4”x33” 30-1/2”x33-1/2” 34”x36”
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com 31
WHOLE HOUSE FANS
2438, 3038R & 3638R
• Three-speed control allows speed selec-
tion under all conditions; wall control
included
• Adjustable side panels permit 30” fan to
be mounted on 16” O.C. ceiling joists
• Heavy-duty construction with cold
formed, channel steel frame and hous-
ing
• Detachable motor, blade and frame
assembly
• Dynamically balanced four-petal blades
for quiet operation
• Two ball bearing, pillow blocks mounted
in live rubber for quiet operation
• 3038R and 3638R are reversible
• Belt drive for quiet, efficient performance
HORIZONTAL / VERTICAL AUTOMATIC SHUTTER
• Each louver is weather-stripped to prevent air infiltration
Automatic shutters for trouble-free service
• Heavy-duty frames
• Weather-resistant, bronze bearings to ensure long service
HORIZONTAL AUTOMATIC SHUTTER
• No need to cut joists - two independent louver sets
open inside 16" O.C. joist space
• Painted aluminum louvers with weather stripping for
tight sealing closure
• Connecting tie rod and adjustable spring counter
balance for reliable opening
• Sturdy frame
CATALOG USED FAN TYPE OF OPENING OVERALL
NUMBER WITH INSTALLATION FINISH REQUIRED SIZE
3124 2037/2438 VERTICAL ALUMINUM 24”X24” 27-1/8”X27-1/8”
3130 3038R VERTICAL ALUMINUM 30”X30” 33-1/8”X33-1/8”
3136 3638R VERTICAL ALUMINUM 36”X36” 39-1/4”X39-1/4”
3224 2438 HORIZONTAL WHITE 24”X24” 26”X26”
3230 3038R HORIZONTAL WHITE 30”X30” 32”X32”
3236 3638R HORIZONTAL WHITE 36”X36” 38”X38”
SPECIFICATIONS
SPECIFICATIONS
CATALOG USED FAN TYPE OF OPENING OVERALL
NUMBER WITH INSTALLATION FINISH REQUIRED SIZE
A3024 3038R, A24DD Horizontal White 30”x33-1/2” 32”x36”
SPECIFICATIONS
0.1 S.P. MINIMUM
CATALOG BLADE CFM @ RPM OVERALL EXHAUST
NUMBER SIZE AMPS 120V SIZE AREA
2438 24” 5.5 3900 @ 745 27-3/4”x27-3/4”x17” 5.2 sq. ft.
3038R 30” 5.5 5500 @ 545 33-3/4”x33-3/4”x17” 7.3 sq. ft.
3638R 36” 7.0 7100 @ 430 39-3/4”x39-3/4”x17” 9.5 sq. ft.
WHOLE HOUSE & ATTIC VENTILATORS
Visit us on the web at www.marleymep.com
ATTIC VENTILATORS
32
RV16
• Our most powerful ventilator for use
in the largest homes
• Low-silhouette dome is unobtrusive
and blends into any roof design
• Bug and bird screen protects against
annoying pests
• 3” high venturi prevents intrusion of
rain, snow and wind
• Dynamically balanced direct drive
motor and blade combinations
• Self-flashing mounting plate for easy
weather-tight installation
• Ventilates 2320 square feet of attic
area with 780 square inches of
intake area
• 27” x 27” mounting plate; aluminum
dome
• Pre-wired junction box with attached
flexible conduit
• Includes adjustable range thermostat
(60˚ to 120˚F)
ASRV14
• Unobtrusive low-silhouette dome
blends into any roof design
• Bug and bird screen protects against
annoying pests
• 3” high venturi prevents intrusion of
rain, snow and wind
• Dynamically balanced direct drive
motor and blade combinations
• Self-flashing mounting plate for easy
weather-tight installation
• Specifically designed for smaller
homes
• 14” blades ventilate up to 1515
square feet of attic area with 480
square inches of intake area
• Aluminum Dome. 23” x 23” mounting
plate
• Unit mounted, integral junction box
and automatic thermostat turns on at
105°F off 95° F
AGV14 & GV16
• AGV14 gable ventilator designed for
average-sized homes
• GV16 gable ventilator designed for
large homes
• 14” blade on AGV14; 16” blade on
GV16
• 18” armored, flexible cable supplied
with GV16
• Heavy-duty steel construction
• Easy to install in existing homes or
new construction
• Optional mounting-exhaust hot air or
pull in cool air
• Mounting brackets included
• AGV14 includes pre-wired automatic
thermostat mounted in junction box
turns on at 105°F off 95° F
• GV16 includes adjustable range ther-
mostat (60° to 120°F)
SPECIFICATIONS
CATALOG HVI CERTIFIED RATINGS BLADE SHIP
NUMBER CFM STATIC PRESSURE DIA. VOLTS AMPS RPM WT.
RV16 1620 .03 16” 120 3.4 1025 23
ASRV14 1060 .03 14” 120 2.2 1550 17
AGV14 1040 .03 14” 120 2.2 1550 10
GV16 1520 .03 16” 120 3.4 1100 18.5
Roof and Gable Vents
Air in attic spaces can reach 150°F or more. This hot air penetrates downward into living space and
the air conditioner strains to sufficiently cool the home. Energy costs drastically increase as the air
conditioner runs almost nonstop. With a Marley Builder Products Roof or Gable Vent, attic air can be
regulated to within 10° of the outside air temperature. Your air conditioner cools the home easier and
saves you money even during the hottest part of summer.
BATHROOM VENTILATION
Visit us on the web at www.marleymep.com 33
COMMERCIAL WALL FANS
BE
• 115V, 1Ø, permanently lubricated, drip proof motor
• Permanently lubricated bearings on blade shaft
• Aluminum blade
• Hot dipped galvanized venturi
• Shipped fully assembled
• 1 Year Limited Warranty
• (Sleeve bearings on 24”, 30”, 36”, Ball bearing on 42”.)
LPE & LPEV
• LPE V - Venturi mounted fan - Provides optimum air flow
and more rigid installation. Can be used with or without
external shutter.
• LPE S - Shutter mounted fan - Reduces installation time
by eliminating inside and outside framing when a shutter is
going to be used.
COMMERCIAL WALL SHUTTER
• For use with BE fans
Air open - Gravity close
• All aluminum
• Bronze bearings
• Weather stripping for tighter seal
SPECIFICATIONS
CATALOG BLADE OUTSIDE AMPS@ CFM @ 115V AMPS SHIP WT.
NUMBER TYPE SIZE DIMENSION HIGH MED LOW (HIGH) (LBS.)
LPE 12V VENTURI 12” 17-3/4” SQ. 2000 / 1600 / 1150 1.1 14
LPE 16V FAN 16” 21” SQ. 3000 / 2650 / 2250 1.1 21
LPE 22V 22” 27-1/2” SQ. 4200 / - / 3700 2.1 37
LPE 12S 12” 15” SQ. 2000 / 1600 / 1150 1.1 16
LPE 16S SHUTTER 16” 19” SQ. 3000 / 2650 / 2250 1.1 25
LPE 24S FAN 24” 27” SQ. 5000 / - / 4200 2.2 44
LPE 30S 30” 33” SQ. 7800 / - /6600 2.5 51
SPECIFICATIONS
FAN ROUGH OVERALL SHIP WT.
MODEL SIZE OPENING SIZE (LBS.)
CWS12 12” 13” X 13” 15” X 15” 4
CWS16 16” 17” X 17” 19” X 19” 6
CWS22 22” 23” X 23” 25” X 25” 8
CWS24 24” 25” X 25” 27” X 27” 11
CWS30 30” 31” X 31” 33” X 33” 12
CWS36 36” 37” X 37’ 39” X 39” 20
CWS42 42” 43” X 43” 45” X 45” 29
SPECIFICATIONS
CATALOG BLADE MOTOR CFM SHIP WT.
NUMBER SIZE HP (FREE AIR) AMPS (LBS.)
BE 24 24” 1/2 6500 6.0 58
BE 30 30” 1/2 8300 6.0 65
BE 36 36” 1/2 10400 6.0 78
BE 42 42” 3/4 14000 9.2 92
WHOLE HOUSE & ATTIC VENTILATORS
Visit us on the web at www.marleymep.com
LOW PROFILE AIR CURTAINS
NOZZLE MAX VEL AVG VEL AIRFLOW WT. MOTORS
MODEL WIDTH (IN) VOLTS AMPS FPM FPM CFM LBS HP
Contemporary Powder Paint
MLP36001115GR 36 120 1.3 1800 1800 / 1350 1200 / 900 32 1 @ 1/15
MLP42001110GR 42 120 1.6 1800 1800 / 1350 1380 / 1040 37 1 @ 1/10
MLP48001108GR 48 120 2.1 1800 1800 / 1350 1600 / 1210 42 1 @ 1/8
MLP60001108GR 60 120 2.1 1800 1800 / 1350 2060 / 1550 53 1 @ 1/8
MLP36001208GR 36 240 0.7 1800 1800 / 1350 1200 / 900 32 1 @ 1/8
MLP42001208GR 42 240 0.7 1800 1800 / 1350 1380 / 1040 37 1 @ 1/8
MLP48001206GR 48 240 1.0 1800 1800 / 1350 1600 / 1210 42 1 @ 1/6
MLP60001206GR 60 240 1.0 1800 1800 / 1350 2060 / 1550 53 1 @ 1/6
Contemporary Stainless Steel
MLP36001115GRSS 36 120 1.3 1800 1800 / 1350 1200 / 900 32 1 @ 1/15
MLP42001110GRSS 42 120 1.6 1800 1800 / 1350 1380 / 1040 37 1 @ 1/10
MLP48001108GRSS 48 120 2.1 1800 1800 / 1350 1600 / 1210 42 1 @ 1/8
MLP60001108GRSS 60 120 2.1 1800 1800 / 1350 2060 / 1550 53 1 @ 1/8
MLP36001208GRSS 36 240 0.7 1800 1800 / 1350 1200 / 900 32 1 @ 1/8
MLP42001208GRSS 42 240 0.7 1800 1800 / 1350 1380 / 1040 37 1 @ 1/8
MLP48001206GRSS 48 240 1.0 1800 1800 / 1350 1600 / 1210 42 1 @ 1/6
MLP60001206GRSS 60 240 1.0 1800 1800 / 1350 2060 / 1550 53 1 @ 1/6
APPLICATION GUIDELINES:
• Create an “open door” atmosphere in retail establishments.
• For mounting heights of 7 ft. for exterior customer entrances or 8 ft. interior doors.
• Reduce infiltration of exterior air, fumes, dust and dirt.
• Act as a temperature separation device, repelling outside air while maintaining interior envi-
ronment.
• Patented design allows for continuous mounting.
FEATURES
• Modern contemporary design with choice of electro-static powder paint or quality stainless
steel.
• Cross-flow blower wheels for maximum outlet uniformity
• Easily adjustable air directional vanes.
• Two speed motor with convenient selector switch
• Pre-wired 48 inch molded cord/plug for simple installation.
• Quick-Mount mounting plate included. No Template required to locate mounting screws
• Units can be installed in series for side by side continuous mounting.
For use as a Thermal Barrier in retail
customer entrances, malls, stores,
hospitals, post offices, restaurants,
concession windows and walk-in
coolers.
Contemporary Design
34
PRODUCT CATEGORY
Visit us on the web at www.marleymep.com 35
PRODUCT CATEGORY
LOW PROFILE AIR CURTAINS
NOZZLE MAX VEL AVG VEL AIRFLOW WT. MOTORS
MODEL WIDTH (IN) VOLTS AMPS FPM FPM CFM LBS HP
Architectural Series
MLP36001115GA 36 120 1.3 1800 1800 / 1350 1200 / 900 32 1 @ 1/15
MLP42001110GA 42 120 1.6 1800 1800 / 1350 1380 / 1040 37 1 @ 1/10
MLP48001108GA 48 120 2.1 1800 1800 / 1350 1600 / 1210 42 1 @ 1/8
MLP60001108GA 60 120 2.1 1800 1800 / 1350 2060 / 1550 53 1 @ 1/8
MLP36001208GA 36 240 0.7 1800 1800 / 1350 1200 / 900 32 1 @ 1/8
MLP42001208GA 42 240 0.7 1800 1800 / 1350 1380 / 1040 37 1 @ 1/8
MLP48001206GA 48 240 1.0 1800 1800 / 1350 1600 / 1210 42 1 @ 1/6
MLP60001206GA 60 240 1.0 1800 1800 / 1350 2060 / 1550 53 1 @ 1/6
APPLICATION GUIDELINES:
• Create an “open door” atmosphere in retail establishments.
• For mounting heights of 7 ft. for exterior customer entrances or 8 ft. interior doors.
• Reduce infiltration of exterior air, fumes, dust and dirt.
Act as a temperature separation device, repelling outside air while maintaining interior environment.
• Patented design allows for continuous mounting.
FEATURES
• Extruded anodized aluminum design that compliments store interiors and public facilities.
• Custom paint to accent architectural sill-height heaters in vestibules and reception areas.
• Cross-flow blower wheels for maximum outlet uniformity
• Easily adjustable air directional vanes.
• Two speed motor with convenient selector switch
• Pre-wired 48 inch molded cord/plug for simple installation.
• Quick-Mount mounting plate included. No Template required to locate mounting screws
• Units can be installed in series for side by side continuous mounting.
Custom paint to accent architectural sill-height heaters in vestibules and reception areas.
For use as a Thermal Barrier in retail
customer entrances, malls, stores,
hospitals, post offices, restaurants,
concession windows and walk-in
coolers.
Architectural Design
ACCESSORIES AND CONTROLS
For use with all air curtains for instant activation or de-activation of
unit upon door opening or closing.
Automatic switches available for all models.
• Plunger Style for hinged doors or Roller Style for sliding and track doors.
C1200R
20 AMP
120
MODEL STYLE VOLTAGE MAX AMPS
C1200R Plunger/Roller 20
SHIP WT.
1 lb
Door Switches
AIR CURTAINS
Visit us on the web at www.marleymep.com
C8930R
• Transmitter mounts to any door; signals
remote receiver announcing an entry
• No wiring; receiver plugs into any outlet
• Select from four melodies or two tones
• 32 privacy codes
DOOR SENTRY
DOOR CHIMES
36
Door Chimes & Push Buttons
The understated beauty of Marley Builder Products’ Chimes lies
beneath the exterior decor, as bells ring clear and pleasing
throughout the home. All door chimes stand the test of time, for
years of reliable, trouble-free operation with
timeless good looks.
In addition to door chimes, we also offer Door Chime Kits,
Wireless Chimes, and Pushbuttons.
C8214
• Built-in chime blends with sur-
rounding decor
• Recessed housing with flush-
mounted louver grille
• Can be painted to match wall
color scheme
• Size: 5-3/4” x 7-5/8” grille;
rough in opening 4-7/8” x 6-7/8”
SYLVAN
C8347R
• Contemporary look
• Cover can be painted or wallpapered
to match any home interior
• Easily recessed in existing walls or
surface mounted
• Two notes front; one note rear
• Size: Grille - 8” x 8”;
rough-in opening - 6-3/8” x 6 3/8”
BRISTOL GLACIER
C8807R
• Bold geometric plane
• Full bodied sound presented
in contemporary white
• Two notes front; one note
rear
• Size: 8-1/4” x 5-1/2”
C8050R
Slimline
Non-Lighted,
White
C8081R
Slimline
Lighted,
White
C8054R
Round
Lighted,
Brass Rim
C8055R
Round
Lighted,
Nickel Rim
ECONOMY
Visit us on the web at www.marleymep.com 37
CHIME KIT CHIME KIT
C8379
• Up-scale double-entry builder kit
• Resonator chamber for improved
sound
• Includes transformer and two lighted
brass finish pushbuttons
C8279
• Double-entry kit
• Includes transformer and two lighted
pushbuttons
• 6-3/8” x 5” x 2”
C8276
• Single-entry kit
• Includes transformer and one lighted
pushbutton
BUZZERS
TRANSFORMER TRANSFORMER
C8136R
• Plastic 15 watt, 16 volt; for four - eight note
chimes
C8138R
• Plastic 15 watt, 24 volt; for multiple chime
installations
C8116R
•BLISTER PACK
• 10 watt, 16 volt
• Recommended for two-note chimes and
general purpose
C8212R1
• Buzzer; 2-1/2” x 2-7/8” x 1”
BELLS & BUZZERS & ACCESSORIES
CHIME KITS
DOOR CHIMES
Visit us on the web at www.marleymep.com
ELECTRIC HEAT
38
MODEL DESCRIPTION
TA1AW Baseboard Thermostat, SP 22 Ampere, 40º to 100ºF
TA2AW Baseboard Thermostat, DP 22 Ampere, 40º to 100ºF.
RA1W Duplex Receptacle.
DSW2W Double Pole Disconnect Switch Rated 20A @ 120-277ºF.
PR24 24 Volt AC, Class 2 Power Relay SPST 30A @ 120-240
VAC, 23A @ 277 VAC
High Altitude
Baseboard Heater (mounted above 7500 Ft.) , add suffix “H” to catalog
number
NOTE: Eight foot length baseboards must be ordered in multiples of two
pieces for shipment.
* Add NW suffix for Northern White color.
2500 - ELECTRIC BASEBOARD HEATERS
• Easily installed without disassembly
• Designed for quiet operation... no popping and ping-
ing normally associated with baseboard heaters.
• Lead wires allow quick field connection to either end
of the heater.
• Continuous capillary tube safety thermal cutout pro-
tection in case of airflow blockage.
• Easy out knockouts at each end for convenient
wiring.
• Chimney fin element design for maximum air circula-
tion. Airflow is directed away from walls to help pre-
vent wall soiling.
• UL listed for installation on wall at floor level with
wall-to-wall carpeting. Heater stands unsupported
during installation.
• *Navajo White enamel finish retains attractive
appearance and is compatible with all interior
decors.
• Pre-notched mounting guide marks for fast and easy
installation without disassembling the unit.
• Built-in cable clamp in both wiring compartments to
restrain incoming cables without using additional
hardware.
• Permanently attached copper grounding wire in
each wiring compartment.
STANDARD DENSITY - 250 WATTS PER FOOT
MODEL
240 VOLT 120VOLT WATTS BTU/HR. LENGTH
2542W 2512W 400 1365 2’
25426W 25126W 500 1706 2’6”
2543W 2513W 750 3412 3’
2544W 2514W 1000 3412 4’
2545W 2515W 1250 4265 5’
2546W 2516W 1500 5118 6’
2548W - 2000 6824 8’
25408W - 2500 8530 8’
Electric Heat
Whether it’s for primary or secondary
use, Marley Builder Products has an
electric heat source for you. Many mod-
els can be utilized in both residential
and commercial settings, with maximum
comfort and minimum operating costs.
Where heat is needed, Marley Builder
Products has an application for you:
• Baseboard Heat - The quietest, highest quality baseboard heat available.
• Convection Heat - Either wall or ceiling mounted, wherever there’s a need for instant heat.
• Wall Heaters - For vestibules, hallways, small and large baths, placed in any size room.
Marley Builder Products offers electric wall heat in several voltages and wattages to provide even,
efficient warmth.
• Ceiling Heaters - When wall space is scarce, ceiling heaters provide the same efficient warmth as
our wall heaters.
Available in colors of white and almond to complement any room interior, Marley Builder Products
also provides the necessary accessories, including thermostats and surface mount kits, becoming
your complete source for electric heat.
SPECIFICATIONS ACCESSORIES
Visit us on the web at www.marleymep.com 39
ELECTRIC HEAT
SHIP WT.
MODEL VOLTS WATTS BTU/HR. AMPS LENGTH (LBS.)
HBB500 120 500 1706 4.2
HBB504 240/208 500/375 1706/1280 2.1/1.8 28” 10
HBB750 120 750 2560 6.3
HBB754 240/208 750/563 2560/1921 3.1/2.7 34” 12
HBB1000 120 1000 3413 8.3
HBB1004 240/208 1000/750 3413/2560 4.2/3.6 46” 15
HBB1250 120 1250 4265 10.4
HBB1254 240/208 1250/938 4265/3200 5.2/4.5 58” 19
HBB1500 120 1500 5120 12.5
HBB1504 240/208 1500/1125 5120/3839 6.3/5.4 70” 22
HBB2004 240/208 2000/1500 6826/5120 8.3/7.2 94” 30
HBB - ELECTRIC HYDRONIC
BASEBOARD HEATERS
A sheathed electric heating element is totally immersed in a
heat-transfer liquid and sealed in a heater-length copper
tube. The large diameter reservoir maximizes the volume of
heat storage to prolong the thermal constant of the entire
heater. All available heat is delivered into the room with
strong convection flow. Gentle heat keeps radiating even
after the thermostat turns off because of the hydronic ele-
ments retention qualities.
GO-ANYWHERE DESIGN. The entire unit mounts flush to
any wall and flat on any floor - wood, carpet or tile. The trim,
three-inch thick functional design and low operating tempera-
tures allow carpeting to be installed up to and around the
baseboard. Efficient air flow is achieved even if the unit is
mounted above the floor.
QUALITY INSIDE AND OUT. Heavy-duty welded steel
louvered grilles discourage insertion of foreign objects and
direct heat outward into the room. Designer-style junction
boxes are made of high-strength Lexan® to resist scratches
and wear marks. Corrosion resistant aluminum fins are
pressure-fitted to copper tubing to assure rapid heat transfer
and air flow. Built-in thermal cut-off automatically shuts down
the heater should any overheating occur.
MODEL DESCRIPTION
HBBT1 25 AMP @ 120-277 VAC Single Pole Thermostat Snap
Action Type. Field Installed in Junction Box.
HBBT2 25 AMP @ 120-277 VAC Double Pole Thermostat Snap
Action Type. Field Installed in Junction Box.
HBBAC* Air Conditioner Outlet Section. 20 AMP @ 208-240 VAC.
HBBDR* Duplex Receptacle Section. 15 AMP @ 120 VAC.
HBBDSDR120* Two pole disconnect switch with 120 VAC receptacle
HBBLVR0* Low Voltage Relay Control Section. 25 AMP @ 120 VAC.
HBBWS* 8” Wiring Sections.
* These accessories are mounted in 8” control box that add length to baseboard.
SPECIFICATIONS
ACCESSORIES
ELECTRIC HEAT
Visit us on the web at www.marleymep.com
ELECTRIC HEAT
40
MODEL VOLTS AMPS WATTS BTU/HR
HT2024SS 240 1.0 - 8.3 250 - 2000 853 - 6826
HT1502SS 120 1.6 - 12.5 200 - 1500 682 - 5120
Fast heat response and Programmable touch screen built-in thermostat
make the Smart Series™ heaters ideal for dens, basements, converted
attics and breezeways, garages, large bathrooms, offices, workshops and
similar areas. Also, adaptable to multiple installations in larger or odd
shaped rooms.
• Heater automatically adjusts wattage output and blower speed resulting
in whisper quiet operation for optimum comfort.
• Heating element is heavy duty non-glowing steel fins brazed to steel
sheathed tubular elements in a grid pattern that covers the entire dis-
charge area.
• Built-in fan delay operates when unit is turned off after heating to prolong
element life.
• 5/2 day electronic programmable built-in thermostat adaptable to fit any
life style while providing energy savings and precise temperature per-
formance.
• Easy to use LED touch screen operation.
• Convenient remote control included.
• Contemporary, clean design with night light feature complements any
decor.
• Designed for easy installation. Heater is mounted prior to wiring. Both
hands are free to make field connections in roomy compartment.
• This heater is designed for installation in 2 x 4 or larger wall sections
using the wall box provided.
• The heater may be wired with standard building wire (60°C). Refer to
specification chart for correct supply voltage and wire size.
12”
3-3/4”
BACK BOX
(Rough-in Box)
(Front View)
(End View)
1"
FRONT
COVER
(Side View)
17-7/16”
12”
13-11/16”
19-9/16”
HT SMART SERIES - PROGRAMMABLE WALL HEATER
12”
3-3/4”
BACK BOX
(Rough-in Box)
(Front View)
(End View)
1"
FRONT
COVER
(Side View)
17-7/16”
12”
13-11/16”
19-9/16”
An easy to use
remote control is
included to provide
convenient heat
and power adjust-
ment from up to 12
feet away.
THERMOSTAT DISPLAY
Time Periods
1 = Wake up period
2 = Daytime period
3 = Evening Period
4 = Sleep Time
Ambient temperature
Fan operation
Automatic Mode
Hold function
Down button
On / Off button
Days of week
Group 1 (Mon to Fri)
Group 2 (Sat & Sun)
Time of day
This area is also used when pro-
gramming custom periods
Centigrade Setting
Fahrenheit Setting
Tamper proof setting
Up button
Mode button
Proportional heat control indicator
Night light indicator
SPECIFICATIONS
HEATER REMOTE
TM
Visit us on the web at www.marleymep.com 41
Adapter frames for surface mounting
• 414 - Use with 1235
SURFACE FRAMES
SHIP WT.
MODEL VOLTS PHASE WATTS AMPS (LBS.)
ECP1024 240/208 1 1000/750 4.0/3.6 27
ECP1524 240/208 1 1500/1125 6.3/5.4 27
ECP - EURO STYLE WALL
HEATERS,
NON-FAN FORCED
• Convection and radiant warmth from
one heater.
• Heater can be surface mounted or
recessed into 2x4 or larger wall sec-
tions. It is designed to fit between
16’ O.C. studs.
• Steel finned metal sheath electric
heating elements provides uniform
heat and long service life.
• Closely spaced bar grille design dis-
courages insertion of foreign objects
and directs air outward to effectively
distribute heat to the middle of the
room.
• Polyester powder painted grille offers
attractive appearance in a neutral
color that is compatible with any
decor.
• Contemporary styling uses soft
curves on all edges, avoiding the
sharp corners of a square design.
• Large wiring compartment is accessi-
ble from the front of the heater
enabling rapid, easy hookup.
• CSA and UL approved.
1235 - ECONOMY WALL
HEATERS
• Heater can be recessed surface
mounted, horizontal or vertical
mounted.
• Exclusive fan venturi design for quiet
operation.
• Clean electric heat requires no duct-
ing or venting.
• Use Model 414 Surface Kit when
mounting directly to wall.
• Front mounted thermostat for con-
venient room comfort control.
• Attractive safety grille removes easily
for cleaning.
• Built-in manual reset thermal safety
switch to prevent overheating.
• Rugged, two-piece construction; easy
to install.
ROUGH-IN
MODEL FINISH OPENING WATTS AMPS VOLTS BTUH
1235 Stainless 9-1/4” x14-1/2” 1500 12.5 120 5120
1235P Almond 9-1/4” x 14-1/2” 1500 12.5 120 5120
2435 Stainless 9-1/4” x 14-1/2” 1500/1125 6.2/5.4 240/208 5120/3839
2435P Almond 9-1/4” x 14-1/2” 1500/1125 6.2/5.4 240/208 5120/3839
SPECIFICATIONS
SPECIFICATIONS
ELECTRIC HEAT
ELECTRIC HEAT
Visit us on the web at www.marleymep.com
THERMOSTATS
42
TH110DPP
• Accurate in maintaining selected temperature up to +/- 1-1/2˚F.
• Choice of Celsius or Fahrenheit; choice of 12 or 24 hour readouts.
• Protected memory, no battery required.
• Easy programming- 4 settings per day, each day can be different.
• Manual mode override option.
• 240 Volt operation.
SPECIFICATIONS
POSITIVE TEMP.
MODEL TYPE AMPS OFF RANGE
TH110DPP DPST 16.7A @ 240V Yes 44ºF - 86ºF
SPECIFICATIONS
RUNNING TEMP.
MODEL VOLTAGE CURRENT @ 30V RANGE
T8775C1005 24 .015 - 1.0A 40ºF - 90ºF
TH5220D1003 24 .015 - 1.0A 40ºF - 90ºF
T8775C1005
• 24 Volt low voltage digital round thermostat 2 wire (Heat
& Cool).
• Easily adjust temperature with the control ring.
• Lighted display, turns on with the touch of a button.
TH5220D1003
• 24 Volt 2-Stage digital thermostat 5-7 wire (Heat & Cool).
Digital Electronic Thermostats
Digital thermostats are an ecological alternative to mercury filled thermostats.
Marley Builder Products offers several models. All models feature a digital display
with backlight feature. Models with set back features are available.
TH300024
• Ultimate temperature control the most accurate type of thermostat on the market
(±0.15°C / 0.27°F)
• On-screen heating power indicator gives at-a-glance verification of power being used
• 2-wire non-polarized connection means fast, hassle-free installation
• Up/Down buttons enable easy temperature setting
Also ideal for radiant ceilings
• Battery-free backup means no re-programming thermostat after power outage
• Silent operation
• Can be used on baseboards, convectors, and radiant panels
SPECIFICATIONS
POSITIVE TEMP.
MODEL TYPE AMPS OFF RANGE
TH300024 TRIAC SPST 120V OR 240V, 12.5A Yes 40ºF - 85ºF
Visit us on the web at www.marleymep.com 43
Limited Warranty
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of
original installation or 18 months from date of manufacture, except special components which are warranted against defects in workmanship and
materials (see installation manual for specific warranties) from date of installation.This warranty does not apply to damage from accident, misuse
or alteration; nor where the connected voltage is more than 5% above the name plates voltage; nor to equipment improperly installed or wired or
maintained in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the installation or
purchase.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs and shipping costs
incurred to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be
returned to the nearest Marley authorized service center or the Marley Engineered Products Service Center and we will repair or replace, at our
option, at no charge to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from
Marley Engineered Products. If the product requires replacement, but an identical model is no longer available, Marley Engineered Products will
select a comparable item.
The above warranties are in lieu of all other warranties expressed or implied and all implied warranties of merchantability and fitness for a partic-
ular purpose which exceed the aforesaid expressed warranties are hereby disclaimed and excluded from this agreement. Marley Engineered
Products shall not be liable for consequential damages arising with respect to the product, whether based upon negligence, tort, strict liability or
contract.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to
you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328.
Merchandise returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley
Engineered Products. When requesting return authorization, include all numbers shown on the products.
MEDALLION LEVELS
We are committed to producing the highest quality products and services to our customers through the continuous
pursuit of excellence in all that we do.
PLATINUM - Limited 5 year warranty on element or motor.
GOLD - Limited 3 year warranty on element or motor.
COMMERCIAL CEILING FANS
Commercial Ceiling Fans
• 18 Pole 115V; Motor
• Permanently sealed double ball bearing motor
• 3/8” x 7-1/4” locking J-hook for installation
• White epoxy finish
• Steel blades
BLADE SHIP WT.
MODEL VOLTS AMPS SIZE CFM/RPM (LBS.) COLOR
CPF56 120 0.85 56” 24000/300 24 White
56HRCF 120 0.70 56” 19800/280 20 White
SPECIFICATIONS
9290R 9290DS, 9290DS2, 9290DS5 558P
SPEED CONTROLS
MODEL DESCRIPTION
9290R Controls one fan. Four-speed rotary control without plate. Ivory and white knob included.
9290DS Controls one fan. Three-speed slide control with white face plate.
9290DS2 Controls two fans. Three-speed slide control with white face plate.
9290DS5 Controls three to five fans. Three-speed slide control with white face plate.
558P Wall control unit, eight amps
Note: Remote Controlled Fans do not require speed controls.
SPECIFICATIONS
ELECTRIC HEAT
ZGC-MBPGC
9/12
www.marleymep.com

Navigation menu