671875 Catalog

2014-09-04

: Pdf 671875-Catalog 671875-Catalog 622454 Batch7 unilog

Open the PDF directly: View PDF PDF.
Page Count: 49

Pocket Pro
ELECTRICAL SYSTEMS
Trenchless Raceways Systems
www.ipexelectrical.com
®TMTM
®®
®
®®
®
Type UL Underwriters Laboratories Inc.
Designation (UL 50 and UL 508)
Indoor use primarily to provide protection
against contact with the enclosed equipment
and against a limited amount of falling dirt.
Indoor use to provide a degree of protection
against limited amounts of falling water and dirt.
Outdoor use to provide a degree of protection
against windblown rain; undamaged by the
formation of ice on the enclosure.
Either indoor or outdoor use to provide a
degree of protection against falling rain,
splashing water, and hose-directed water;
undamaged by the formation of ice on the
enclosure.
Either indoor or outdoor use to provide a
degree of protection against falling rain,
splashing water, and hose-directed water;
undamaged by the formation of ice on the
enclosure; resists corrosion.
Indoor or outdoor use primarily to provide a
degree of protection against hose-directed
water, the entry of water during prolonged
submersion at a limited depth, and be
undamaged by the formation of ice on the
enclosure.
Indoor use to provide a degree of protection
against dust, dirt, fiber flyings, dripping water,
and external condensation of noncorrosive
liquids.
Indoor use to provide a degree of protection
and spraying of water, oil, and noncorrosive
liquids.
This material is reproduced with permission from
Underwriters Laboratories Inc. Standard for Safety
for Cabinets and Boxes, UL 50, Copyright 1988
and Industrial Control Equipment, UL 508, Copyright
1994 by Underwriters Laboratories Inc.
Underwriters Laboratories Inc. (UL) shall not be
responsible to anyone for the use of or reliance
upon a UL Standard by anyone. UL shall not incur
any obligation or liability for damages, including
consequential damages, arising out of or in
connection with the use, interpretation of, or reliance
upon a UL Standard.
1
2
3
4
4X
12
13
6P
123456 78
1
SCEPTER PVC CONDUIT SCEPTER PVC
FITTINGS CONDUIT REPAIR KIT SCEPTALIGHT CORLINE ENT &
KIWKON FITTINGS SUPERDUCT SCEPTACON KWIKPATH
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . .3
Advantages . . . . . . . . . . . . . . . . . . . . . . . . . .4
Scepter®Rigid PVC Conduit . . . . . . . . . . . . . . .7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Expansion and Contraction . . . . . . . . . . . . . . . . . . .10
Conduit Dimensions . . . . . . . . . . . . . . . . . . . . . . . .15
Scepter®PVC Conduit Fittings . . . . . . . . . . . .17
Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Cover Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Weatherproof Covers . . . . . . . . . . . . . . . . . . . . . . . .34
Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Conduit Cements & Primers . . . . . . . . . . . . . . . . . .42
Conduit Repair Kit . . . . . . . . . . . . . . . . . . . .43
EPR Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
EPR Kit Adapters . . . . . . . . . . . . . . . . . . . . . . . . . .43
SceptalightTM: Nonmetallic Light Fixtures . . . .45
Cor-Line®ENT & Kwikon®Fittings . . . . . . . . . .53
Cor-Line Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Kwikon Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Kwikon Accessories . . . . . . . . . . . . . . . . . . . . . . . .61
Super Duct® . . . . . . . . . . . . . . . . . . . . . . . . . .63
Advantages/Engineering Data . . . . . . . . . . . . . . . . .64
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Vertical-Lok Spacers . . . . . . . . . . . . . . . . . . . . . . . .76
Monobloc®Spacers . . . . . . . . . . . . . . . . . . . . . . . .77
SceptaConTM Trenchless Raceway Systems . . .79
Kwikpath®Communication Raceway Systems . .81
23
Engineers, electricians, contractors, specifiers and utilities have
realized for many years the advantages of PVC. Today, IPEX electrical
systems include Scepter®PVC conduit and fittings, Super Duct®power
and communication ducts, Cor-Line®ENT, Kwikon®ENT fittings and
FiberTel®high density polyethylene innerduct. These brands are the
number-one choice for power, communication and data needs.
Whether exposed, concealed in walls, encased in concrete, or directly
buried, IPEX electrical products are preferred
For The Long Run
.
Only when you specify IPEX branded products by name are you
guaranteed our commitment to excellence.
Applications
Typical industrial/commercial and residential applications for IPEX
electrical systems include:
• Utilities
• Cable
• Communications
• Street and highway lighting
• Residential applications
• Water treatment plants
• Airports
• Subways
• Sewage treatment plants
• Pulp and paper industries
• Parking garages
• Car washes
Fish plants
• Marinas
• Agricultural, dairy, hogs, cattle,
chicken, etc.
• Bridges and tunnels
• Food processing plants
• Steel mills
• Mines
APPLICATIONS
INTRODUCTION
Pocket Pro provides the most comprehensive information about PVC
systems – from basic raw material to installation characteristics of the
finished product. Written with the engineer, contractor and distributor
in mind, it is based on laboratory test results and IPEX’s many years of
field experience.
At IPEX, we have been extruding PVC conduit and molding fittings
since 1951. We formulate our own compounds, maintain strict quality
control during production, and offer one of the most comprehensive
lines of nonmetallic electrical products throughout North America.
More important, our commitment to customers extends beyond the
sale. Quality control and thorough jobsite field reports have earned
IPEX a reputation for product quality and service excellence.
45
Easy Wire Pulls
PVC’s exceptionally smooth interior surface greatly reduces the
amount of friction while pulling conductors/wires through long runs,
even with 90° bends. A large pull-rope and wire-pulling compound
should be used when pulling all conductors and wires.
Noncorroding
PVC is immune to damage from naturally
corrosive soil conditions, as well as electro-
chemical and galvanic corrosion. This
ensures lower maintenance costs and
superior performance
For The Long Run.
Nonconducting
Scepter Rigid PVC conduit pipe and fittings
are nonsparking and nonconducting, thereby
eliminating the most dangerous ‘second
point of contact’ and ‘phase to ground’
faults. The use of a separate grounding
conductor provides a complete and positive
ground for the whole system.
Chemical Resistance
One of the greatest benefits of PVC is its
excellent chemical resistance. It resists
attack by acids, alkalies, salt solutions, and
many other types of chemicals. For more
information on PVC and chemical
resistance, refer to the IPEX Chemical
Resistance Guide.
Long Life
Scepter Rigid PVC Conduit pipe and fittings
retain their original properties after years of
exposure to heat and weather. In addition,
resistance to fungi, bacterial action,
rodents, termites and corrosive agents
ensures a long, trouble-free life for PVC
conduit installed indoors or outdoors.
Concrete Tight
Scepter Rigid PVC Conduit pipe and fittings
are designed and engineered to be concrete
tight in all weather conditions.
ADVANTAGES
ADVANTAGES
Labour Savings
Compared to metal, PVC products reduce labour on a typical installation
by up to two-thirds. The reason? PVC is easy to work with. It can also be
cut and joined without pipe vises, cutters, threading equipment and
reamers associated with metal conduit.
Lightweight Conduit
Scepter Rigid PVC Conduit is one-half the weight of aluminum and
one-sixth the weight of steel. As a result, handling and installation are
easier and faster, reducing labour costs.
Sunlight Resistant
The 2006 Canadian Electrical Code rule 2-130 is intended to ensure
that totally enclosed nonmetallic raceways are properly protected
against adverse effects from direct exposure to UV rays. Electrical
nonmetallic raceways marked for such applications are suitable for
installation and use in direct exposure to the rays of the sun. Scepter
rigid PVC Conduit meets the criteria for sunlight resistance, is
approved for the purpose, and is appropriately marked.
Easy Joining
Solvent cementing is all that is required, eliminating the need for
power-threading machines, pipe vises and cutting equipment. A
hacksaw or carpenter’s saw is the only equipment required.
Strength
Scepter Rigid PVC Conduit offers both high impact and high tensile
strength, even in cold temperatures. Scepter Rigid PVC Conduit and
fittings meet and exceed all CSA and UL standards.
Scepter Rigid
PVC Conduit
CSA
Impact Test
UL
Impact Test
Size
(in)
Size
(mm) @ -29°F (-34°C) @ 72°F (23°C)
1/2 12 8.9 ft.lbs. (12 joules) 50 ft.lbs. (68 joules)
3/4 20 8.9 ft.lbs. (12 joules) 80 ft.lbs. (109 joules)
125 8.9 ft.lbs. (12 joules) 100 ft.lbs. (136 joules)
1 1/4 32 8.9 ft.lbs. (12 joules) 120 ft.lbs. (163 joules)
1 1/2 40 8.9 ft.lbs. (12 joules) 150 ft.lbs. (204 joules)
250 8.9 ft.lbs. (12 joules) 190 ft.lbs. (258 joules)
2 1/2 65 8.9 ft.lbs. (12 joules) 210 ft.lbs. (285 joules)
3 – 6 75 – 150 8.9 ft.lbs. (12 joules) 220 ft.lbs. (298 joules)
67
SCEPTER PVC CONDUIT
This section covers the most comprehensive design and installation of
Scepter Rigid PVC Conduit pipe and fittings. Always consult the
authority having jurisdiction for specific installation procedures.
CSA C22.2 No. 211.2
CSA C22.2 No. 211.0
FT-4 for 1/2" to 6"
NEMA TC-2
Corps. of Engineers Spec.
CE 303:01
Military Spec, Federal Spec.
WC 1094A
SCEPTER RIGID PVC CONDUIT
Fire Resistant
IPEX’s proprietary PVC compound used to manufacture Scepter
products is a self-extinguishing material and will not support
combustion. Samples taken from an actual fire show the outer surface
of the conduit was blistered and charred. The interior of the conduit,
however, was unaffected. Additionally, the undamaged conductors
were then removed and reinstalled in new conduit.
Fire-resistant characteristics when tested to CAN ULC S102.2 are as
follows:
FT-4 Rating
Scepter Rigid PVC conduit is certified to meet
the requirements of FT-4 allowing its use in
noncombustible construction per Section 3.1.5.20
of the National Building Code, which reads:
1.)
Subject to the limits on the size of elements
that penetrate fire separations as stated in
Sentence 3.1.9.3.(2), within a fire compartment
of a building required to be of noncombustible
construction, totally enclosed nonmetallic
raceways not more than 175mm in outside
diameter, or of an equivalent rectangular area,
are permitted to be used to enclose optical fibre
cables and electrical wires and cables, provided
the raceways exhibit a vertical char not more
than 1.5m when tested in conformance with the
Vertical Flame Test (FT - 4) Conduit or Tubing
on Cable Tray in Clause 6.16 of CSA C22.2
No. 211.0, “General Requirements and
Methods of Testing for Nonmetallic conduit.”
Suitable for Direct Burial
PVC is suitable for direct burial and requires no extra protection when
installed in accordance with the Canadian Electrical Code and the
local inspection authority guidelines. The usual care regarding
trenches and backfilling should be respected.
One-Source Specification
IPEX offers a full range of PVC fittings and accessories. As a result, it
is easy to specify a single source PVC system.
Quality Control
In addition to IPEX’s quality control testing, all Scepter electrical
products carry third-party certification by CSA, UL and NRTL.
ADVANTAGES
IPEX Compound Flame
Spread
Smoke
Developed
Fuel
Contribution
0.080" (2mm) thickness 10 – 20 225 – 270 0
0.630" (16mm) thickness 10 – 20 300 – 390 0
89
SCEPTER PVC CONDUIT
SCEPTER PVC CONDUIT
Solvent Cementing
After cutting Scepter Rigid PVC conduit,
sharp edges or burrs from inside the conduit
should be removed with a knife. Thoroughly
clean the end of the pipe and inside the
fitting with a pipe cleaner. Apply a generous
amount of IPEX solvent cement to both
surfaces; slide together and give a quarter
turn to ensure the solvent is spread evenly on
the material. Hold together for a few seconds
until the joint is made.
Usually the solvent-cemented joint will be
strong enough to install immediately.
However, in climates with low temperatures or
areas with high humidity, extra time may be
required before moving the pipe for permanent installation. Solvent-
cemented joints appear to “set up” instantly, but will take 24 hours to
cure properly. After this time, the solvent-cemented joint has
completely cured and is waterproof. For extreme cold weather
installations, the use of IPEX PVC Primer is recommended. IPEX
cements and primers are available in quarter-pint (125ml), half-pint
(250ml), pint (500ml), quart (1-litre) and gallon (4-litre) containers.
Bending
PVC is a thermoplastic material that, when
heated, becomes soft and pliable. As a
result, its shape can be altered.
A flameless heat source is recommended to
heat the pipe. AN OPEN FLAME SHOULD
NOT BE USED. Either an electric unit or an
infra-red propane unit is recommended.
The necessary temperature for bending pipe
is 260°F (127°C). The pipe must be heated
evenly over an area approximately ten times
the diameter of the pipe before any attempt
at bending is made. Bending the pipe when
it has not been thoroughly heated will cause
the pipe to “kink.” With proper care and a
little practice, the bend will form easily.
Cooling the pipe with cold air or water will
cause “spring back.” Allow a few extra
degrees of overbending to compensate.
Maximum bending radius shall be six times
the internal diameter according to the
Canadian Electrical Code.
INSTALLATION
Maximum Operating
Temperature
The Canadian Electrical Code (CEC) allows
the use of Scepter Rigid PVC Conduit up
to a maximum ambient temperature of
167°F (75°C).
Cutting
Scepter Rigid PVC conduit can be easily cut
on the jobsite by using a hacksaw,
carpenter’s saw or PVC conduit cutters. For
larger sizes of conduit, the use of a mitre box
is also recommended to ensure a square cut.
Support
Due to PVC’s light weight, support
spacing is different than that used
with metal conduits. Supporting
straps should NOT be firmly tightened,
so that linear movement of the pipe is
possible. The maximum allowable support
spacing, as per Canadian Electrical Code (CEC),
is as follows:
Support Spacing For Scepter Rigid PVC
Conduit Pipe
INSTALLATION
Nominal Conduit Diameter Maximum Support Spacing
inches mm feet metres
1/2 12 2-1/2 0.75
3/4 20 2-1/2 0.75
125 2-1/2 0.75
1-1/4 32 41.2
1-1/2 40 41.2
250 51.5
2-1/2 65 61.8
375 61.8
3-1/2 90 72.1
4100 72.1
5125 72.1
6150 82.5
10 11
SCEPTER PVC CONDUIT
SCEPTER PVC CONDUIT
Number of Expansion Joints Required
Use the following equation to determine the number of expansion
joints needed for a Scepter Rigid PVC Conduit installation:
Number of joints =
E = Expansion joint travel length 101.6mm (4") or 203.2mm (8")
depending on diameter.
Always round up to the next whole number.
Setting the Piston Opening
The expansion joint must be installed to allow for expansion and
contraction of the conduit run. On a cold day, if an expansion joint is
installed completely closed with the piston bottomed, there is no room
for expansion when the conduit is warmed. If it is installed open to the
maximum on a hot day, the expansion joint will pull apart when cooled.
The correct piston opening for any installation condition can be easily
determined using the formula below:
Piston setting =
Compressed length + max. temp. – installation temp. x E
max. temp. – min. temp.
Formula can be used for both metric and imperial measurements.
total expansion (mm or in)
E
EXPANSION & CONTRACTION
EXPANSION & CONTRACTION
Using Expansion Joints
It’s just as important to know when to use an
expansion joint as it is to know how to install it
correctly. Expansion joints are required when the
temperature change is greater than 25°F (14°C).
Scepter Rigid PVC conduit has a coefficient of
linear expansion of 3.6 x 10-4 in./ft./°F
(.054mm/m/°C.) Generally, a 100 ft. (30.48m)
run of PVC conduit will undergo a change in
length of 3.6 inches (91.44mm) for every 100°F
(56°C) temperature change.
For conduit installed indoors, the range of expansion and contraction
can be calculated using the maximum air temperature plus the heat
contributed by the conductors inside the conduit and minimum air
temperature expected. Expansion joints are not required indoors
unless there are widely varying temperatures such as the attic of a
building.
Conduit installed outdoors, exposed to direct sunlight, will be
considerably hotter than the air temperature. As a guideline in this
case, add 27°F (15°C) to the temperature change. Expansion joints
should be installed to allow for all anticipated temperature changes.
Expansion
Formula
By using the following
formulas and the charts
below, the total expected
expansion in a run can be
easily determined:
°F
Total Expansion (in.)
= length of run (ft.)
x temperature change
(°F) x 0.00036
°C
Total Expansion (mm)
= length of run (m)
x temperature change
(°C) x 0.054
0 1 2 3 4 5
120
110
100
90
80
70
60
50
40
30
20
10
PVC PIPE
As a general rule
for every
temperature
change of 10ºF,
PVC pipe will
expand or contract
3/8" per 100'
TEMPERATURE CHANGE IN ºF
LENGTH VARIATION in/100 ft OF PIPE
PVC PIPE LENGTH VARIATION
DUE TO TEMPERATURE CHANGE (ºF)
Coefficient = 3.6 x 10-4 in/ft/ºF
0 .5
1.0 1.5 2.0
2.5 3.0 3.5
60
55
50
45
40
35
30
25
20
15
10
5
TEMPERATURE CHANGE IN ºC
LENGTH VARIATION mm/m OF PIPE
PVC PIPE LENGTH VARIATION
DUE TO TEMPERATURE CHANGE (ºC)
Coefficient = .054/mm/m/ºC
As a general rule
for every
temperature
change of 5ºC,
PVC pipe will
expand or contract
2.7mm per 10m
PVC PIPE
Size Compressed Length Travel
(mm) (in) (mm) (in) (mm) (in)
13 1/2 203.2 8.00 101.6 4
20 3/4 203.2 8.00 101.6 4
25 1215.9 8.50 101.6 4
32 1-1/4 228.6 9.00 101.6 4
38 1-1/2 228.6 9.00 101.6 4
51 2235.0 9.25 101.6 4
64 2-1/2 235.0 9.25 101.6 4
76 3362.0 14.25 203.2 8
89 3-1/2 362.0 14.25 203.2 8
102 4362.0 14.25 203.2 8
127 5362.0 14.25 203.2 8
152 6362.0 14.25 203.2 8
or
()
12 13
SCEPTER PVC CONDUIT
SCEPTER PVC CONDUIT
EXPANSION & CONTRACTION
Figure 1
Figure 2
Figure 3
Figure 4
EXPANSION & CONTRACTION
Location of Expansion Joints
Proper functioning of an expansion joint depends on three procedures:
1. The correct placement of the expansion joint.
2. The proper installation of Scepter Rigid PVC conduit and the
expansion joint.
3. The proper placement and fastening of support straps.
One Expansion Joint
Figure 1
If only one expansion joint is needed between two boxes, the barrel of
the joint is rigidly fastened close to the first box. Scepter Rigid PVC
conduit should then be loosely supported with straps, allowing the
conduit to move freely as it expands and contracts.
Two Expansion Joints
Figure 2
If two expansion joints are
needed, the joints should
be firmly fastened back to
back at the centre of the run.
Scepter Rigid PVC conduit is
loosely supported with straps,
allowing the conduit to move freely as it
expands and contracts.
Two Expansion Joints (Alternative)
Figure 3
Alternatively, the centre of the run and the two expansion joints
(located at the boxes) should be rigidly fastened. All other support
straps should be loosely fastened.
Three or More Expansion Joints
Figure 4
If more than two joints are needed in a very long run, they should be
put in a series, one after the other. Each barrel must be rigidly
fastened while conduit is loosely supported with straps allowing the
conduit to move freely as it expands and contracts. When installed in a
series, each section acts independently of the other. Spacing of conduit
supports must be in accordance with Section 12-1114 of the Canadian
Electrical Code (CEC).
14 15
SCEPTER PVC CONDUIT
SCEPTER PVC CONDUIT
Scepter Rigid PVC Conduit Dimensions (inches)
CONDUIT DIMENSIONS
Scepter Rigid PVC Conduit Dimensions (mm)
EXPANSION & CONTRACTION
Installation of Expansion Joints
Installation recommendations:
• Expansion joints should be mounted so the piston can travel in a
straight line in the barrel. If the alignment is not straight, the
piston will bind, preventing the joint from functioning correctly.
• The expansion joint barrel should be clamped tight, but the conduit
mounted loose enough in its hangers to allow for movement as it
expands and contracts.
• Scepter nonmetallic straps are correctly sized and designed for
proper support, and must be used to secure the conduit.
• When expansion joints are used in a vertical position, the piston
should be mounted in a downward position so dirt cannot deposit
between the barrel and piston at the muzzle of the expansion joints.
WARNING
Common Mistakes
Three common mistakes are:
1. Forgetting to use expansion joints.
2. Not using enough expansion joints.
3. Overtightening of support straps.
It is more cost effective to use more expansion joints than needed,
rather than too few. It is difficult to correct the problem after
conductors are installed and in service. Failure to accommodate
expansion/contraction may result in pipe fracture.
Nominal
Size Product Code OD ID Min.
Wall
Weight
lbs/100'
Standard
ft/crate
1/2 (10') 032105 0.840 0.622 0.109 15 6,000
(20') 032106 12,000
3/4 (10') 032107 1.050 0.824 0.113 21 4,400
(20') 032108 8,800
1(10') 032110 1.315 1.049 0.133 31 3,600
(20') 032111 7,200
1-1/4 (10') 032112 1.660 1.380 0.140 42 3,300
(20') 032114 6,600
1-1/2 (10') 032115 1.900 1.610 0.145 53 2,250
(20') 032116 4,500
2(10') 032120 2.375 2.067 0.154 71 1,400
(20') 032121 2,800
2-1/2 (10') 032125 2.875 2.469 0.203 112 780
(20') 032126 1,560
3(10') 032130 3.500 3.068 0.216 166 780
(20') 032131 1,560
3-1/2 (10') 032135 4.000 3.548 0.226 200 630
(20') 032136 1,260
4(10') 032140 4.500 4.026 0.237 236 600
(20') 032141 1,200
5(10') 032150 5.563 5.047 0.258 321 230
(20') 032151 460
6(10') 032160 6.625 6.065 0.280 417 260
(20') 032161 520
Nominal
Size OD ID Min. Wall Weight
kgs/100'
12 21.3 15.8 2.8 22.6
20 26.7 20.9 2.9 31.2
25 33.4 26.6 3.4 46.2
32 42.2 35.1 3.6 63.0
40 48.3 40.9 3.7 78.4
50 60.3 52.5 3.9 105.5
65 73.0 62.7 5.2 167.2
75 88.9 77.9 5.5 247.8
90 101.6 90.1 5.7 297.7
100 114.3 102.3 6.0 352.4
125 141.3 128.2 6.6 478.5
150 168.3 154.1 7.1 621.0
16 17
SCEPTER PVC
FITTINGS
SCEPTER PVC CONDUIT
Industry leaders specify Scepter PVC fittings by name. For years,
Scepter PVC fittings have set the standard for quality and value-added
features not normally available from other suppliers. Features such as our
threaded brass inserts, brass screws, and superior PVC gasketing system
make a real difference.
NEMA TC-2, 3
C22.2 No. 85 UL Listed
UL514B – UL514C
SCEPTER
®
CONDUIT FITTINGS
Weight Comparison of Scepter Rigid PVC
Conduit - kg/100 m
CONDUIT DIMENSIONS
Weight Comparison of Scepter Rigid PVC
Conduit - lbs./100 ft.
Nominal Size (in) Rigid PVC Aluminum Rigid Steel
1/2 15 28 79
3/4 21 27 105
131 53 153
1-1/4 42 70 201
1-1/2 53 86 249
271 116 334
2-1/2 112 183 527
3166 239 690
3-1/2 200 288 831
4236 340 982
5321 465 1,334
6417 613 1,771
NEMA TC2
Corps. of Engineers Spec.
CE 303:01
Military Spec, Federal Spec.
WC 1094A
Nominal Size (in) Rigid PVC Aluminum Rigid Steel
12 23 41 118
20 31 54 157
25 46 79 228
32 63 104 300
40 78 129 371
50 106 173 498
65 167 272 786
75 248 356 1,029
90 298 429 1,239
100 352 507 1,464
125 479 694 1,989
150 621 914 2,641
CSA C22.2 No. 211.2
FT-4 for 1/2 " to 6"
18 19
SCEPTER PVC
FITTINGS
SCEPTER PVC
FITTINGS
Female Adapters
AC
D
B
5° Couplings
FITTINGS
Threaded Reducer Bushings
FITTINGS
A B
C
Couplings
Terminal Adapters
Note: 1/2" to 1-1/4" TA – tapered thread.
1-1/2" to 6" TA – non-tapered thread.
Size (in) Part
Number
Product
Code A (in) B (in) C (in)
1/2 EC10 077001 1.080 0.840 1.437
3/4 EC15 077002 1.300 1.050 2.200
1EC20 077003 1.590 1.315 2.031
1-1/4 EC25 077004 2.000 1.660 2.156
1-1/2 EC30 077005 2.230 1.900 2.281
2EC35 077006 2.720 2.375 2.406
2-1/2 EC40 077007 3.320 2.875 3.187
3EC45 077008 4.000 3.500 3.437
3-1/2 EC50 077009 4.500 4.000 3.625
4EC55 077010 5.000 4.500 3.750
5EC60 077011 6.120 5.563 4.187
6EC65 077012 7.370 6.625 4.562
Size (in) Part
Number
Product
Code A (in) B (in) C (in) D (in)
1/2 TA10 077021 0.700 0.591 0.750 1.550
3/4 TA15 077022 0.675 0.790 1.000 1.750
1TA20 077023 0.625 1.000 1.115 1.860
1-1/4 TA25 077024 0.640 1.311 1.300 2.125
1-1/2 TA30 077025 0.725 1.530 1.425 2.250
2TA35 077026 0.800 1.970 1.150 2.100
2-1/2 TA40 077027 0.800 2.346 1.900 2.930
3TA45 077028 0.815 2.915 2.000 3.055
3-1/2 TA50 077029 1.000 3.385 1.715 3.055
4TA55 077030 0.815 3.850 1.990 3.215
5TA60 077031 1.725 5.015 2.000 5.985
6TA65 077032 1.875 6.025 2.130 6.500
Note: All female adapters have NPT-tapered threads.
Size (in) Part Number Product Code L (in)
25EC35 077100 4.0
2-1/2 5EC40 077101 5.5
35EC45 077103 6.0
3-1/2 5EC50 077102 7.0
45EC55 077104 7.0
55EC60 077105 7.5
65EC65 077106 11.0
Size (in) Part Number Product Code
3/4 x 1/2 1825 077314
1 x 1/2 1826 077315
1 x 3/4 1827 077316
Size (in) Part
Number
Product
Code A (in) B (in) C (in) D (in)
1/2 FA10 076544 0.620 1.080 0.800 1.725
1/2 FA10 077041 0.620 1.080 0.800 1.725
3/4 FA15 077042 0.820 1.300 0.800 1.900
1FA20 077043 1.065 1.590 1.000 2.300
1-1/4 FA25 077044 1.395 2.000 1.015 2.425
1-1/2 FA30 077045 1.575 2.230 1.050 2.440
2FA35 077046 2.050 2.720 1.075 2.550
2-1/2 FA40 077047 1.020 3.250 1.500 2.700
3FA45 077048 3.090 4.000 1.630 4.100
3-1/2 FA50 077049 3.540 4.500 1.800 3.895
4FA55 077050 4.025 5.000 1.755 4.210
5FA60 077051 5.035 6.120 2.065 5.240
6
FA65 077052 6.045 7.370 2.065 5.235
20 21
SCEPTER PVC
FITTINGS
SCEPTER PVC
FITTINGS
FITTINGS
Reducer Bushings
End Caps
FITTINGS
Size (in) Part Number Product Code
3/4 x 1/2 1805 077300
1 x 1/2 1805-1 077301
1 x 3/4 1806 077302
1-1/4 x 3/4 1807-1 077303
1-1/4 x 1 1807 077304
1-1/2 x 1 1808-1 077305
1-1/2 x 1-1/4 1808 077306
2 x 1 1809-1 077313
2 x 1-1/4 1809 077307
2 x 1-1/2 1810 077308
2-1/2 x 2 1811 077309
3 x 2 1812-1 077310
3 x 2-1/2 1812 077311
4 x 2 1813-1 077319
4 x 3 1813 077312
4 x 3-1/2 1814 077317
Size (in) Part Number Product Code
1/2 CAP10 077421
3/4 CAP15 077422
1CAP20 077423
1-1/4 CAP25 077424
1-1/2 CAP30 077425
2CAP35 077426
2-1/2 CAP40 077427
3CAP45 077428
3-1/2 CAP50 077429
4CAP55 077430
5CAP60 077431
6CAP65 077432
Size
(in)
Part
Number
Product
Code
A (in)
max.
B (in)
min.
1/2 EJ10 077381 12.00 8.00
3/4 EJ15 077382 12.00 8.00
1EJ20 077383 12.50 8.50
1-1/4 EJ25 077384 13.00 9.00
1-1/2 EJ30 077385 13.00 9.00
2EJ35 077386 13.25 9.25
2-1/2 EJ40 077387 13.25 9.25
3EJ45 077388 22.25 14.25
3-1/2 EJ50 077389 22.25 14.25
4EJ55 077390 22.25 14.25
5EJ60 077391 22.25 14.25
6EJ65 077392 22.25 14.25
“O” Ring Expansion Joints
Expansion and Deflection Fitting Assemblies
Size (in) Part Number Description Product Code
2SE-J-35 Complete Assembly 077889
3SE-J-45 Complete Assembly 077890
4SE-J-55 Complete Assembly 077891
Utility 90° Elbows c/w
Solvent Bell End
D
T
R
B
min.
A
max.
Size
(in)
Part
Number
Product
Code D (in) T (in) R (in)
2NSL 2-24 069257 2.375 41.20 24
2NSL 2-36 069260 2.375 31.70 36
3NSL 3-24 069265 3.500 41.20 24
3NSL 3-36 069261 3.500 31.70 36
4NSL 4-36 069267 4.500 31.70 36
4NSL 4-48 069266 4.500 22.25 48
5NSL 5-36 069263 5.563 31.70 36
6NSL 6-36 069264 6.625 31.70 36
*Additional sizes of reducer bushings are available upon request.
90° Elbows
c/w Solvent Bell End
22 FITTINGS 23
SCEPTER PVC
FITTINGS
SCEPTER PVC
FITTINGS
FITTINGS
Size
(in)
Part
Number
Product
Code D (in) T (in) R (in)
1/2 EE1090 069081 0.840 1.500 4.00
3/4 EE1590 069082 1.050 1.500 4.50
1EE2090 069083 1.315 1.875 5.75
1-1/4 EE2590 069084 1.660 2.000 7.25
1-1/2 EE3090 069085 1.900 2.000 8.25
2EE3590 069086 2.375 2.000 9.50
2-1/2 EE4090 069087 2.875 3.000 10.50
3EE4590 069088 3.500 3.125 13.00
3-1/2* EE5090 069089 4.000 3.250 15.00
4EE5590 069090 4.500 3.375 16.00
5EE6090 069091 5.563 3.625 24.00
6EE6590 069092 6.625 3.750 30.00
With integral bell.
45° Elbows
c/w Solvent Bell End
Size
(in)
Part
Number
Product
Code D (in) T (in) R (in)
1/2 EE1045 069201 0.840 1.500 4.00
3/4 EE1545 069202 1.050 1.500 4.50
1EE2045 069203 1.315 1.875 5.75
1-1/4 EE2545 069204 1.660 2.000 7.25
1-1/2 EE3045 069205 1.900 2.000 8.25
2EE3545 069206 2.375 2.000 9.50
2-1/2 EE4045 069207 2.875 3.000 10.50
3EE4545 069208 3.500 3.125 13.00
3-1/2* EE5045 069209 4.000 3.250 15.00
4EE5545 069210 4.500 3.375 16.00
5EE6045 069211 5.563 3.625 24.00
6EE6545 069212 6.625 3.750 30.00
With integral bell.
30° Elbows
(Plain End x Plain End)
D
T
R
Size
(in)
Part
Number
Product
Code D (in) T (in) R (in)
1/2 EE1030 069241 0.840 1.500 4.00
3/4 EE1530 069242 1.050 1.500 4.50
1EE2030 069243 1.315 1.875 5.75
1-1/4 EE2530 069244 1.660 2.000 7.25
1-1/2 EE3030 069245 1.900 2.000 8.25
2EE3530 069246 2.375 2.000 9.50
2-1/2 EE4030 069247 2.750 3.000 10.50
3EE4530 069248 3.500 3.125 13.00
3-1/2 EE5030 069249 4.000 3.250 15.00
4EE5530 069250 4.500 3.375 16.00
5EE6030 069251 5.563 3.625 24.00
6EE6530 069252 6.625 3.750 30.00
Utility 90° Elbows
c/w Solvent Bell End
Size
(in)
Part
Number
Product
Code D (in) T (in) R (in)
2NSL 2-24 069257 2.375 10.200 24.00
2NSL 2-36 069260 2.375 31.700 36.00
3NSL 3-24 069265 3.500 41.200 24.00
3NSL 3-36 069261 3.500 31.700 36.00
4NSL 4-36 069267 4.500 31.700 36.00
4NSL 4-48 069266 4.500 31.700 48.00
5NSL 5-36 069263 5.563 31.700 36.00
6NSL 6-36 069264 6.625 31.700 36.00
* Plain end only
* Plain end only
90° Elbows
Extended bend
Size
(in)
Part
Number
Product
Code D (in) T (in) R (in)
1-1/4 EE2590E 069096 1.66 10.24 6.73
1-1/2 EE3090E 069097 1.90 12.80 8.25
2EE3590E 069098 2.38 11.02 13.00
D
T
R
90º
25
SCEPTER PVC
FITTINGS
X
Y
Z
24
SCEPTER PVC
FITTINGS
FITTINGS
PVC Coated Steel, 2 Hole
Size (in) Part Number Product Code
2CS35 077818
2-1/2 CS40 077819
3CS45 077820
3-1/2 CS50 077821
4CS55 077822
5CS60 077824
6CS65 077823
PVC Coated Steel, 1 Hole
Size (in) Part Number Product Code
1/2 CS10-1 077831
3/4 CS15-1 077832
1CS20-1 077833
1-1/4 CS25-1 077834
1-1/2 CS30-1 077835
2CS35-1 077836
2-1/2 CS40-1 077837
3CS45-1 077838
3-1/2 CS50-1 077839
4CS55-1 077840
Conduit Clamps & Spacers
Size
(in)
Part
Number
Product
Code X (in) Y (in) Z (in)
1/2 CCS10 077794 1.191 2.414 1.824
3/4 CCS15 077796 1.195 2.660 2.106
1CCS20 077797 1.215 2.962 2.443
1-1/4 CCS25 077798 1.182 3.300 2.855
1-1/2 CCS30 077799 1.193 3.600 3.170
2CCS35 077800 1.195 4.135 3.785
Strut
Base CCS-B 077343 _ _ _
*CCS-B are sold individually, two pieces are required
to create one base unit.
Pipe Straps PVC, 2 Hole
Size (in) Part Number Product Code
1/2 PS10 077811
3/4 PS15 077812
1PS20 077813
1-1/4 PS25 077814
1-1/2 PS30 077815
2PS35 077816
Polyethylene (PE), 2 Hole
Size (in) Part Number Product Code
2-1/2 PS40 077262
3PS45 077263
4PS55 077264
27
SCEPTER PVC
FITTINGS
26
SCEPTER PVC
FITTINGS
FITTINGS
Access Fittings* Type LL
Size (in) Part Number Product Code
1/2 SLL10S 077521
3/4 SLL20S 077522
1SLL30S 077523
1-1/4 SLL40S 077524
1-1/2 SLL50S 077525
2SLL60S 077526
2-1/2 SLL70S 077527
3SLL80S 077528
3-1/2 SLL90S 077530
4SLL100S 077529
TYPE LL
E
B
C
F
H
B
I
G
Access Fittings* Type C
B
DE
B
C
A
Size (in) Part Number Product Code
1/2 SC10S 077501
3/4 SC20S 077502
1SC30S 077503
1-1/4 SC40S 077504
1-1/2 SC50S 077505
2SC60S 077506
2-1/2 SC70S 077507
3SC80S 077508
3-1/2 SC90S 077510
4SC100S 077509
FITTINGS
Access Fittings* Type LB
Size (in) Part Number Product Code
1/2 SLB10S 077541
3/4 SLB20S 077542
1SLB30S 077543
1-1/4 SLB40S 077544
1-1/2 SLB50S 077545
2SLB60S 077546
2-1/2 SLB70S 077547
3SLB80S 077548
3-1/2 SLB90S 077549
4SLB100S 077550
B
E
C
G
F
H
KB
I
Access Fittings* Type LR
Size (in) Part Number Product Code
1/2 SLR10S 077481
3/4 SLR20S 077482
1SLR30S 077483
1-1/4 SLR40S 077484
1-1/2 SLR50S 077485
2SLR60S 077486
2-1/2 SLR70S 077480
3SLR80S 077488
3-1/2 SLR90S 077487
4SLR100S 077489
* All access fittings are CSA and UL listed for wet locations. Supplied with threaded brass
inserts, combination brass head screws and PVC gasketing.
* Stainless steel screws are available upon request.
**Not UL Listed.
29
SCEPTER PVC
FITTINGS
28
SCEPTER PVC
FITTINGS
FITTINGS
Access Fittings* Type TB**
Size (in) Part Number Product Code
1/2 STB10S 077451
3/4 STB20S 077452
1STB30S 077453
1-1/4 STB40S 077454
1-1/2 STB50S 077455
2STB60S 077456
B
DE
B
C
J
J
KL
I
Access Fitting Dimensions*
Size (in) A (in) B (in) C (in) D (in) E (in) F (in)
1/2 5.606 0.639 1.268 1.100 0.840 4.337
3/4 5.606 0.810 1.536 1.325 1.050 5.395
16.500 0.910 1.700 1.600 1.335 6.250
1-1/4 7.900 1.050 2.300 2.250 1.660 7.625
1-1/2 8.500 1.125 2.675 2.250 1.900 8.250
210.875 1.160 3.188 2.820 2.375 10.531
2-1/2 14.600 1.750 4.500 3.950 2.870 13.630
314.600 1.900 4.500 3.950 3.510 13.630
3-1/2 17.040 2.125 5.536 5.000 4.000 16.000
417.040 2.125 5.536 5.000 4.530 16.000
Size (in) G (in) H (in) I (in) J (in) K (in) L (in)
1/2 4.095 1.297 2.487 2.280 1.005 0.750
3/4 4.095 1.297 2.487 2.803 1.005 0.810
14.750 1.500 2.075 3.250 1.125 1.115
1-1/4 5.750 1.750 3.575 3.950 1.562 1.300
1-1/2 6.500 1.750 3.938 4.250 1.656 1.425
28.156 2.344 4.535 5.438 1.968 1.160
2-1/2 9.825 3.805 6.240 7.300 2.610 -
310.897 2.733 6.240 7.300 2.610 -
3-1/2 11.465 4.535 7.500 8.535 2.975 -
411.465 4.535 7.500 8.535 2.975 -
* All access fittings are CSA and UL listed for wet locations. Supplied with threaded brass
inserts, combination brass head screws and PVC gasketing.
* Stainless steel screws are available upon request.
**Not UL Listed.
FITTINGS
* All access fittings are CSA and UL listed for wet locations. Supplied with threaded brass
inserts, combination brass head screws and PVC gasketing.
* Stainless steel screws are available upon request.
**Not UL Listed.
Access Fittings* Type T
Size (in) Part Number Product Code
1/2 ST10S 077461
3/4 ST20S 077462
1ST30S 077463
1-1/4 ST40S 077464
1-1/2 ST50S 077465
2ST60S 077466
2-1/2 ST70S 077467
3ST80S 077468
3-1/2 ST90S 077571
4ST100S 077572
B
E
B
J J
D
B
Access Fittings* Type E
Size (in) Part Number Product Code
1/2 SE10S 077561
3/4 SE20S 077562
1SE30S 077563
1-1/4 SE40S 077564
1-1/2 SE50S 077565
2SE60S 077566
2-1/2 SE70S 077567
3SE80S 077568
3-1/2 SE90S 077569
4SE100S 077570
EC
F
B
31
SCEPTER PVC
FITTINGS
30
SCEPTER PVC
FITTINGS
FITTINGS
Meter Hubs
Size (in) Part Number Product Code
1-1/4 MHU25 077961
1-1/2 MHU30 077963
2MHU35 077965
2-1/2 MHU40 077967
3MHU45 077968
Long Meter Offsets
(Fabricated)
Size (in) Part Number Product Code
1-1/4 LMO25 069641
1-1/2 LMO30 069645
2LMO35 069646
End Bells
Size (in) Part Number Product Code
1/2 EB-10 077406
3/4 EB-15 077085
1EB-20 077323
1-1/4 EB-25 077324
1-1/2 EB-30 077325
2EB-35 077326
2-1/2 EB-40 077327
3EB-45 077328
3-1/2 EB-50 077329
4EB-55 077330
5EB-60 077331
6EB-65 077332
Service Entrance Fittings
Size (in) Part Number Product Code
1/2 EF10 077281
3/4 EF15 077282
1EF20 077283
1-1/4 EF25 077284
1-1/2 EF30 077285
2EF35 077286
2-1/2 EF40 077287
3EF45 077288
3-1/2 EF50 077289
4EF55 077290
Meter Offsets
Size (in) Part Number Product Code
1-1/4 MO25 077941
2MO35 077942
FITTINGS
“Two in One” Pull Elbow
The “two in one” access pull elbow reduces
inventory costs & increases installation flexibility
(3/4" hub fitting supplied with 3/4" x 1/2"
reducers). The pull elbow is approved for wet
location use and is manufactured from high
impact, nonconducting and noncorroding PVC.
Size (in) Part Number Product Code
1/2 or 3/4 PE15/10 077491
33
SCEPTER PVC
FITTINGS
32
SCEPTER PVC
FITTINGS
GASK20-3
F Series - Double Gang Plates
F Series - Triple Gang Plates
COVER PLATES
1.415”
dia. dia. dia.
1.610” 1.760”
DRC15/10 TSC15/10 20RC15/10 20-3RC15/10 30-3RC15/10 BRC15/10
BRC20-2 TSC20-2 TSDC20-2
DRC20-2
BRC20-3 DRC20-3 DSDR20-3 TSC20-3 TSDC20-3
GASK 15/10
GASK20-2
F Series - Single Gang Plates
Description Part Number Product Code
Duplex Receptacle DRC15/10 077617
Toggle Switch TSC15/10 077616
Single Receptacle 20RC15/10 077618
Single Receptacle 20-3RC15/10 077619
Single Receptacle 30RC15/10 077620
Blank c/w Gasket BRC15/10 077611
PVC Gasket GASK15/10 077621
Description Part Number Product Code
Blank Cover c/w Gasket BRC20-2 077614
Double Switch TSC20-2 077738
Double Duplex Receptacle DRC20-2 077740
Combo Switch Duplex Rec. TSDC20-2 077739
PVC Gasket GASK20-2 077743
Description Part Number Product Code
Triple Receptacle DRC20-3 077747
Combo Switch Receptacle DSDR20-3 077745
Triple Switch TSC20-3 077744
Combo Switch Receptacle TSDC20-3 077746
Blank Cover c/w Gasket BRC20-3 077748
PVC Gasket GASK20-3 077749
Grommet From To
W = .195" W = .285"
L = .450" L = .530"
W = .220" W = .291"
L = .516" L = .565"
Ø = .240" Ø = .300"
Ø = .290" Ø = .385"
Ø = .405" Ø = .500"
Ø = .525" Ø = .625"
Strain Relief Connectors Grommet Dimensions
Note: All grommets are supplied with TSRC10, TSRC15 and SRC15.
FITTINGS
Strain Relief Connectors
c/w 6 Grommets
Size (in) Part Number Product Code
3/4 SRC15 077985
Nonmetallic Threaded Strain Relief Connector
c/w “O” Ring, Locknut & 6 Grommets
Size (in) Part Number Product Code
1/2 TSRC10 077754
3/4 TSRC15 077756
35
SCEPTER PVC
FITTINGS
34
SCEPTER PVC
FITTINGS
WEATHERPROOF COVERS
VSC20-2
VSRC20-2
VSDR20-2
VSGG20-2
VSDD20-2
VSRR20-2
Weatherproof Covers - Double Gang
Description Part
Number
Product
Code
Toggle Switch Cover VSC20-2 077741
Combination Switch
& GFI Receptacle VSRC20-2 077742
Combination Switch
& Duplex Receptacle VSDR20-2 077752
Combination Switch
& Single Receptacle
Cover
VSRR20-2 077753
Double Door GFCI
Cover VSGG20-2 077096
Double Door Duplex
Cover VSDD20-2 077097
Gasket for 2-Gang ‘F’
Boxes
(except VSGG20-2
& VSDD20-2)
GASK20-2 077743
Gasket for VSGG20-2
& VSDD20-2 Double
Gangs
GASKV20-2 072227
WEATHERPROOF COVERS
WTL15
WTL20
WTL30
WDR15/10
RWDR15/10
WTL50
WGF15/10
RWGF15/10
Note: Weatherproof covers, with lids closed, are CSA and UL Listed for wet locations.
WDRE15/10
RWDRE15/10
Description (in) Part
Number
Product
Code
Plunger-style Switch
Cover VPT15/10 077630
Toggle Switch Cover VSC15/10 077612
Grey Toggle Switch
Cover WTG15/10 077606
Grey Duplex
Receptacle WDR15/10 077993
White Duplex
Receptacle RWDR15/10 077786
Grey Ground Fault
Receptacle WGF15/10 077785
White Ground Fault
Receptacle RWGF15/10 077787
Single Receptacle
Device 15 AMP 1.375 WTL15 077992
Single Receptacle
Device 20 AMP 1.625 WTL20 077994
Single Receptacle
Device 30 AMP 1.722 WTL30 077991
Single Receptacle
Device 50 AMP 2.187 WTL50 077951
Grey Double Door
Duplex Receptacle WDRE15/10 077087
White Double Door
Duplex Receptacle RWDRE15/10 077408
Gasket for W Series
Cover (except WDRE &
RWDRE)
GASKW 077755
Gasket for WDRE &
RWDRE Covers GASKDD 072225
Weatherproof Covers - Single Gang
VSC15/10
VPT15/10
WTG15/10
37
SCEPTER PVC
FITTINGS
36
SCEPTER PVC
FITTINGS
FD-3
FD-2
FSC-2-101520
FSCC-2-101520
FSS-2-101520
FSC-3-101520
FS-3-101520
BOXES
Note: All F series boxes are supplied with integral mounting feet, threaded brass inserts and
grounding clips.
H
W
D
H
W
D
FS-2-101520
F Series Double Gang Boxes
FS-2 cu.in = 39.5, FSC-2 & FSS-2 cu.in. = 37.0, FSCC-2 cu.in.= 36.0
Hub Size (in) Part Number Product
Code
OD (inches)
HWD
1/2, 3/4, 1 FS-2-101520 077440 4.5 4.75 2.5
1/2, 3/4, 1 FSC-2-101520 077441 4.5 4.75 2.5
1/2, 3/4, 1 FSS-2-101520 077442 4.5 4.75 2.5
1/2, 3/4, 1 FSCC-2-101520 077443 4.5 4.75 2.5
Blank FD-2 077734 4.75 4.75 3.0
F Series Triple Gang Boxes
Hub Size (in) Part Number Product
Code
OD (inches)
HWD
1/2, 3/4, 1 FS-3-101520 077337 4.5 6.6 2.5
1/2, 3/4, 1 FSC-3-101520 077438 4.5 6.6 2.5
Blank FD-3 077737 4.5 6.6 3.0
BOXES
F Series Single Gang Boxes
Outside Dimensions:
Height, 49/16" – Width, 213/16" – Depth 2", Cubic Inches = 25.67
Size (in) Part Number Product Code
1/2 FSC10 077607
3/4 FSC15 077608
1/2 FS10 077601
3/4 FS15 077602
1/2 FSCC10 077622
3/4 FSCC15 077623
1/2 FSS10 077604
3/4 FSS15 077605
Note: 10 = 1/2" Hub, 15 = 3/4" Hub
FS FSCC
FSC FSS
FD Series Single Gang Deep Boxes
Outside Dimensions:
Height, 49/16" – Width, 213/16" – Depth 23/4", Cubic Inches = 35.30
With the exception of the FD Blank Box, Scepter FD Series Single
Gang Deep Boxes are molded with 1" conduit hubs and supplied with
reducer bushings. The conduit hub(s) are field modified as 1/2", 3/4"
or 1" to accommodate job-site requirements. The appropriate quantity
of 1" x 3/4" and 3/4" x 1/2" reducers to create the desired hub size
are packaged with each FD Series Single Gang Deep Box.
Size (in) Part Number Product Code
1/2, 3/4, 1 FDC101520 077291
1/2, 3/4, 1 FDS101520 077299
BLANK FD BLANK 077603
347 VOLT FD347 077610
FDC101520
FDS101520
FD Blank
39
SCEPTER PVC
FITTINGS
38
SCEPTER PVC
FITTINGS
BOXES
Standard PVC
Coupling
Flanged Box with Fibre-Reinforced Safety
Tread Cover
Scepter’s Flanged ‘H’ Series Junction Boxes provide H10 Highway
Loading. The fiber-reinforced safety tread cover secures using recessed
Hex Key fastening hardware offering a simple installation while
reducing the opportunity for tampering.
Size
(in)
Part
Number
Box ID (in)
LWD
Lid Dimensions (in)
ABC
H664 077685 6 6 4-1/4 9.0 9.0 0.60
H666 077686 6 6 6-1/4 9.0 9.0 0.60
H884 077687 8 8 4-1/4 11.5 11.5 0.75
H886 077688 8 8 6-1/4 11.5 11.5 0.75
H887 077689 8 8 7-1/4 11.5 11.5 0.75
H887-A 077692 8 8 7-1/4 11.5 11.5 0.75
C
A
C
B
H887 H887A
Fabricated Boxes
Unflanged PVC fabricated boxes of any size may be made to
customers’ specifications and come complete with lids, gaskets and
screws. These boxes are not CSA Certified and are not returnable.
Junction Box Adapters
Size (in) Part Number Product Code
1/2 JBA10 077721
3/4 JBA15 077722
1JBA20 077723
1-1/4 JBA25 077724
1-1/2 JBA30 077725
2JBA35 077726
2-1/2 JBA40 077727
3JBA45 077728
3-1/2 JBA50 077729
4JBA55 077730 Junction Box
Adapter
BOXES
BCA
A
F
B
C
D
E
* Octagonal Boxes are not designed for supporting luminaires.
Octagonal Boxes*
Octagonal Boxes are shipped complete with cover,
gasket, 4 reducing bushings (3/4" x 1/2") and 4
sealing caps to be installed from inside box to
seal off unused entry hubs.
Size (in) Part Number Hub Size (in) Product Code
4 x 1-1/2 OB15/10 1/2 – 3/4 077983*
4 x 2-1/8 OB20 1077984*
Octagonal Box Extension Rings
Size (in) Part Number Product Code
4 x 1 deep XR20 077989*
4 x 2 deep XR35 077990*
Junction boxes are supplied with
threaded brass inserts, brass screws,
PVC gasketing and mounting feet.
Nylon and stainless steel screws, as
well as larger sizes of fabricated
junction boxes, are available upon
request.
Part
Number
Product
Code
A
(in)
B
(in)
C
(in)
E
(in)
E
(in)
F
(in)
JB442 077659 3.675 4.000 3.450 2.125 2.000 8-32
JB444 077696 3.675 4.000 3.450 4.188 3.750 8-32
JB446 077669 3.675 4.000 3.450 6.225 6.000 8-32
JB552 077670 4.680 5.000 4.485 2.000 1.845 8-32
JB664 077697 6.000 6.375 5.813 4.188 4.000 10-32
JB666 077698 6.000 6.375 5.813 6.188 6.000 10-32
JB884 077664 8.075 8.625 7.966 4.230 4.005 1/4-20
JB887 077671 8.100 8.625 7.966 7.250 7.035 1/4-20
JB12124 077672 12.085 12.580 11.874 4.256 4.030 1/4-20
JB12126 077666 12.085 12.580 11.874 6.240 6.025 1/4-20
JB12128 077668 12.085 12.580 11.874 8.250 8.025 1/4-20
PVC Molded Junction Boxes
(F = Threaded brass insert size.)
Scepter PVC junction boxes are:
NEMA 1, 2, 3, 4, 4x, 6P, 12, 13
UL listed for wet locations
41
SCEPTER PVC
FITTINGS
40
SCEPTER PVC
FITTINGS
BOXES
BOXES
Floor Box Base
(Includes disposable protective cap & reducer plugs)
076954 FB
Floor Box Base c/w Leveling Ring Adapter
(includes disposable protective cap, reducer plugs
& leveling ring adapter)
077068 FBKIT
Floor Box Stand Kit (includes FB Box)
(is equiped with several height brackets which
accommodate the different rebar and post-tension cable
heights and slab depths found from job-site to job-site.)
077700 FBS-KIT
Metal Cover Adapter Kit
(includes leveling ring, metal cover adapter & 2 gaskets)
076953 AFMC
Universal Leveling Ring Adapter
076606 LRA-U
Floor Box Duplex Receptacle Cover (Nonmetallic)
(includes flush mount cover, blank cover & gasket)
Brown 076943 FBDRCB
Gold 076942 FBDRCG
Grey 076941 FBDRCGr
Light Almond 076940 FBDRCA
Tri-Service Universal Divider Kit
(includes upper & lower dividers, riser tube & two grommets)
077948 FBUDK
Y Connector (3/4")
077499 FBYC
Brass Cover Plates
(offers a one-piece design measuring 5-3/4" diameter. Are available
in a variety of styles accommodating power and communication
needs. Install to the FB box using the universal leveling ring adapter.
Nonmetallic Floor Box, Cover & Metal Cover
Adapter
Installation is quick and simple with our nonmetallic floor box and
covers, saving both time and money over similar metallic assemblies.
Scepter’s floor box and duplex receptacle covers are constructed from
high impact, noncorroding and nonconducting PVC.
The flush-mount covers are available in custom colours and are shipped
with a leveling ring complete with a grounding clip. Metal cover adapter
kits are also available, allowing you to adapt to metal floor plates. Our 6"
deep floor box allows flexibility for various concrete floor pours, while
the 4 3/4" width offers easy access and ample wire room. Scepter’s FB
box is molded with 2 - 1" and 2 - 3/4" hub openings.
All boxes are shipped complete with reducer plugs for added versatility.
FB
AFMC
FBS-KIT
LRA-U
FBDRC
Description Part
Number
Product
Code
FBUDK
FBYC
This simple yet innovative Round Floor Box Stand is equipped
with several height brackets which
accommodate the different rebar
and post-tension cable heights
and slab depths found from job-
site to job-site. When installed
together, the Floor Box and
Stand can be used in 5-1/2"
to 10" slab depths.
Sold as a Kit, IPEX offers the
Round Floor Box and Stand
conveniently packaged
together as one complete
product offering.
Four Adjustable Heights
Raises Entrance Hubs to
Rebar
Minimizes Footprint on
Concrete Form
Withstands Tough Job Site
Conditions
Easy to Install
Cost Effective
For more information, visit our NEW website www.ipexelectrical.com
One Kit, Four Heights, One Low Cost!
FEATURE & BENEFITS
Duplex Screw Cover DSC 178091
Duplex Screw Cover DSC-P/C 178092
Single Screw Cover SSC 178093
Single Screw Cover SSC-P/C 178094
Duplex Flip Lid (single) DFL-1 178095
Duplex Flip Lid (double) DFL-2 178096
43
CONDUIT REPAIR KIT
CONDUIT REPAIR KIT
Size (in) Part Number Product Code
1-1/4 EPR25 077976
1-1/2 EPR30 077971
2EPR35 077972
2-1/2 EPR40 077973
3EPR45 077974
4EPR55 077975
5EPR60 077977
6EPR65 077979
EPR Kit for Conduit Repair
EPR Kits from IPEX are the first total
repair systems for broken and damaged
PVC conduit. They offer fast and easy
repairs for damaged conduit caused by
actions such as earth excavation,
horizontal and core drilling.
All sizes are 24 inches in length.
Conduit Repair Kit
Size (in) Part Number Product Code
2EPRA35 077852
3EPRA45 077853
4EPRA55 077854
5EPRA60 077855
6EPRA65 077856
EPR Kit Adapters for Duct
Repair
EPR Conduit Repair Kits allow contractors
to repair a broken section of DB-II duct
while leaving the cables inside. The Adapters are pre-cut allowing
each to open around existing cabling and are then solvent cemented
onto the outside diameter of the broken duct. Using standard PVC
solvent cement, an EPR Kit is then easily assembled and connected to
the Adapters, restoring the duct to its original form.
42
SCEPTER PVC
FITTINGS
Conduit Cement c/w Applicator Cap
Size Part Number Product Code
125ml S100PT25 074717
250ml S100PT5 074713
500ml S100PT 074714
1L S100QT 074715
4L S100GAL 074716
Primer
Size Part Number Product Code
250ml C100PT5 074306
500ml C100PT 074307
1L C100QT 074308
1/2 12 350 700 2-1/2 12 40 80
3/4 19 200 400 319 35 70
125 150 300 3-1/2 25 30 60
1-1/4 32 110 220 432 24 48
1-1/2 38 80 160 538 10 20
250 45 90 650 816
Nominal Pipe
Size
# of
Joints
# of
Joints
Nominal Pipe
Size
# of
Joints
# of
Joints
inches mm /Pint /Quart inches mm /Pint /Quart
Average # of Joints per Pint or Quart of Cement
45
SCEPTALIGHT
SCEPTALIGHT: The Light That Lasts
Sceptalight fixtures from IPEX prove themselves to be all-round
performers in a variety of indoor and outdoor applications.
Sceptalight fixtures are made from a glass-reinforced thermoplastic
polyester resin, which enable them to stand up better to corrosive
elements than metal. This thermoplastic design marries an unrivaled
balance of strength, stiffness and toughness with all the benefits
users appreciate of Scepter rigid PVC conduit and fittings - long life,
easy servicing and high impact-resistance.
Sceptalight's thermoplastic construction offers outstanding corrosion
and chemical resistance. And its interior and exterior silicone gaskets
create a watertight seal, the reason it performs equally well indoors
and outside.
Features and Benefits
Stable Construction
Watertight seal with weather-resistant silicone gaskets
Corrosion Resistant
Durable and Impact Resistant
Mounting Options
SCEPTALIGHTTM
Box with four 3/4
"
threaded hubs and
integral mounting feet.
CEILING MOUNT
Box with four 3/4
"
threaded hubs, 90º wall
bracket and integral
mounting feet.
WALL MOUNT
Pendant cap with
3/4
"
threaded hub
and a locking set
screw.
PENDANT MOUNT
Bookmark Our New Website
www.ipexelectrical.com
OUR SCEPTER ELECTRICAL
CATALOGUE & ELECTRICAL
POCKET PRO INCLUDE MORE
INFORMATION ON:
Conduit & Fittings Duct
Light Fixtures Trenchless Raceways
ENT Tubing & Fittings and much more ...
PRODUCT INFO,
TECHNICAL
DOCUMENTS,
ONLINE TRAINING
& MUCH MORE ...
available at www.ipexelectrical.com
47
SCEPTALIGHT
46
SCEPTALIGHT
SCEPTALIGHTTM
Wet Locations
Ceiling Mount
Ceiling Mount
with Standard Clear Glass Globe
Part
Number
Product
Code
150W Incandescent LVPF150C 077225
150W Incandescent less guard LVPF150LG 077237
26W Compact Fluorescent LVPL26C 077170
18W Compact Fluorescent LVPL18C 077210
13W Compact Fluorescent LVPL13C 077122
9W Compact Fluorescent LVPL9C 077121
7W Compact Fluorescent LVPL7C 077120
Ceiling Mount with Clear Polycarbonate
Glass Globe (no guard)
Part
Number
Product
Code
26W Compact Fluorescent LVPL26PCC 077176
18W Compact Fluorescent LVPL18PCC 077211
13W Compact Fluorescent LVPL13PCC 077165
9W Compact Fluorescent LVPL9PCC 077155
7W Compact Fluorescent LVPL7PCC 077145
4 3/4"
10"
6"
9 1/2"
4 3/4"
11 3/4"
Ceiling Mount Ceiling Mount Ceiling Mount
Polycarbonate Globe
C22.2 No. 250
UL 1598
Globe Options
Sceptalight offers a variety of globe options to suit a wide range of
applications and environments. Our standard clear glass globes are
ideal for general purpose area lighting for either indoor or outdoor use.
Polycarbonate globes offer impact resistance in case of accidental
contact and the assurance that work areas are not contaminated by
broken glass. Coloured globes - available in red, blue, green or amber -
can transform the light to an indicator or warning light.
Light Options
Fluorescents
Our compact fluorescent fixtures work four to five times more
efficiently per watt than incandescents and provide 10-20 times the
lamp life, yet use approximately 75% less energy. In this way,
Sceptalight fluorescents lower energy and maintenance costs without
sacrificing light levels.
Incandescents
With their low initial cost, Sceptalight incandescent fixtures make
the most practical choice to meet the daily needs of commercial,
industrial, marine and agricultural applications. Our incandescents
are ideal for short burn times as well as flashing and dimming
applications.
SCEPTALIGHTTM
Heat-treated
Amber Glass
Heat-treated
Green Glass
Heat-treated
Blue Glass
Heat-treated
Red Glass
Clear
Polycarbonate
Standard or Heat-treated
Clear Glass
49
SCEPTALIGHT
48
SCEPTALIGHT
SCEPTALIGHTTM
Ceiling Mount
with Heat Resistant Glass Globe
Part
Number
Product
Code
150W Incandescent clear LVPF150HRC-HAZ 077414
150W Incandescent red LVPF150HRR-HAZ 077415
150W Incandescent blue LVPF150HRB-HAZ 077416
150W Incandescent green LVPF150HRG-HAZ 077417
150W Incandescent amber LVPF150HRA-HAZ 077494
26W Compact Fluorescent clear LVPL26HRC-HAZ 077377
26W Compact Fluorescent red LVPL26HRR-HAZ 077378
26W Compact Fluorescent blue LVPL26HRB-HAZ 077379
26W Compact Fluorescent green LVPL26HRG-HAZ 077399
26W Compact Fluorescent amber LVPL26HRA-HAZ 077400
18W Compact Fluorescent clear LVPL18HRC-HAZ 077347
18W Compact Fluorescent red LVPL18HRR-HAZ 077348
18W Compact Fluorescent blue LVPL18HRB-HAZ 077349
18W Compact Fluorescent green LVPL18HRG-HAZ 077353
18W Compact Fluorescent amber LVPL18HRA-HAZ 077354
Hazardous
Locations
Ceiling Mount
Wall Mount
Pendant Mount
with Heat Resistant Glass Globe
Part
Number
Product
Code
150W Incandescent clear LPMF150HRC-HAZ 077495
150W Incandescent red LPMF150HRR-HAZ 077496
26W Compact Fluorescent clear LPPL26HRC-HAZ 077407
26W Compact Fluorescent red LPPL26HRR-HAZ 077409
18W Compact Fluorescent clear LPPL18HRC-HAZ 077500
18W Compact Fluorescent red LPPL18HRR-HAZ 077498
Description Part
Number
Product
Code
For wall mount fixtures select and order the
appropriate style (wattage and globe) ceiling
mount fixture from above and add LWB150
Wall Mount bracket
LWB150 077233
Pendant Mount
Class I, Div 2 Groups A, B, C & D
Class II, Div 2 Groups F & G
SCEPTALIGHTTM
Wall Mount
7 1/4"
2 7/8"
13 1/4"
Description Part
Number
Product
Code
For wall mount fixtures select and order the
appropriate style (wattage and globe) ceiling
mount fixture from above and add LWB150
Wall Mount bracket
LWB150 077233
Pendant Mount
with Standard Clear Glass Globe
Part
Number
Product
Code
150W Incandescent LPMF150C 077231
26W Compact Fluorescent LPPL26C 077184
18W Compact Fluorescent LPPL18C 077212
13W Compact Fluorescent LPPL13C 077185
9W Compact Fluorescent LPPL9C 077183
7W Compact Fluorescent LPPL7C 077182
Pendant Mount with Clear
Polycarbonate Globe (no guard)
Part
Number
Product
Code
26W Compact Fluorescent LPPL26PCC 077375
18W Compact Fluorescent LPPL18PCC 077273
13W Compact Fluorescent LPPL13PCC 077365
9W Compact Fluorescent LPPL9PCC 077355
7W Compact Fluorescent LPPL7PCC 077345
4 3/4"
10 1/4"
4 3/4"
12"
Pendant Mount
51
SCEPTALIGHT
50
SCEPTALIGHT
SCEPTALIGHTTM
Accessories & Components
*LFB150T complete with 1/2 threaded"
hole in center of cover
Heat Resistant Globes
Description Part Number Product Code
Clear LG150T 077909
Red LCGR150T 077239
Blue LCGB150T 077910
Green LCGG150T 077241
Amber LCGA150T 077242
Threaded Junction Boxes
Part Number Product Code
LFB150C 077250
LFB150T * 077251
Polycarbonate Globes (for use with
compact fluorescent or maximum 60W incandescent lamp)
Description Part Number Product Code
Clear LPCC18 077911
Red LPCR18 077912
Blue LPCB18 077913
Green LPCG18 077914
Amber LPCA18 077915
Standard Glass Globes
Description Part Number Product Code
Clear LGC150 077247
SCEPTALIGHTTM
Nonmetallic Utility Light Fixture
Description Part
Number
Hub
Size
Product
Code
Fixture c/w Clear Glass Globe LVPE150-10/15 1/2"-3/4"077493
Fixture c/w Clear Polycarbonate Globe LVPE150-PCC*1/2"-3/4"077181
Fixture c/w Heat Resistant Clear Globe LVPE150-HRC 1/2"-3/4"077578
Fixture c/w Heat Resistant Red Globe LVPE150-HRR 1/2"-3/4"077599
Fixture c/w Heat Resistant Blue Globe LVPE150-HRB 1/2"-3/4" 077579
Fixture c/w Heat Resistant Green Globe LVPE150-HRG 1/2"-3/4"077597
Fixture c/w Heat Resistant Amber Globe LVPE150-HRA 1/2"-3/4" 077598
Replacement Clear Glass Globe LGC150 077247
Nonmetallic Clamp-on Guard LVPUG150 077558
Fixture c/w Clear Glass Globe
& Clamp-on guard LVPE150-1015G 1/2"-3/4"077402
*Maximum 60W incandescent lamp with polycarbonate globe
LVPE150 LVPE150-PCC
LVPUG150 LVPE150-1015G
5 1/8"
11
5 1/8"
9 7/8"
3 1/2"
*
53
CORLINE ENT &
KIWKON FITTINGS
52
SCEPTALIGHT
Cor-Line ENT –
Savings for the Long Run
Noncorroding and nonconducting, Cor-Line Electrical Nonmetallic
Tubing and fittings are designed
For The Long Run
. Coiled in
lengths up to 1,500 feet, the Cor-Line system can span the longest
run. Encased in concrete, concealed in walls or ceilings, Cor-Line
offers the best alternative to the labour-intensive, 10' lengths of
metal conduit with its couplings and scrap. The Cor-Line System is
the right choice!
Kwikon Fittings
Our unique Kwikon couplings, transition couplings and connectors are
designed with six 360° locking tabs to ensure a secure concrete-tight
connection.
Time-consuming taping and solvent cementing are eliminated.
C22.2 – No. 227.1
COR-LINE
®
ENT & KWIKON
®
FITTINGSSCEPTALIGHTTM
Accessories & Components con’t
Fixture Components (LVPF, LVPL, LPMF, LPPL)
Description Part Number Product Code
Ceiling Mount Box LVPB 150 077243
Pendant Mount Cap LPC 150 077246
90 Wall Bracket LWB 150 077233
Socket Base Assembly LSBA 150 077245
Medium Base Replacement Socket LSOC 150 077249
Screw-on Guard LVPG 150 077978
Replacement Lamps
Description Part Number Product Code
7 Watt LD/E 7 072841
9 Watt LD/E 9 072844
13 Watt LD/E 13 072847
18 Watt (Quad) LD/E 18 077947
26 Watt (Quad) LD/E 26 077081
Replacement Lamp Holders
Description Part Number Product Code
7/9 Watt Lamp Holder LLH 7/9 072843
13 Watt Lamp Holder LLH 13 072849
18 Watt Lamp Holder (4 Pin) LLH 18 072818
26 Watt Lamp Holder (4 Pin) LLH 26 077082
Ballasts
Description Part Number Product Code
7/9 Watt Magnetic Ballast (NPF) LEB 7/9 072842
13 Watt Magnetic Ballast (NPF) LEB 13 072848
18 Watt Electronic Ballast (HPF) LEB 18 077224
26 Watt Electronic Ballast (HPF) LEB 26 077080
Gaskets
Description Part Number Product Code
Box Gasket LBGASK 150 072820
Lamp Gasket LLGASK 150 076971
55
CORLINE ENT &
KIWKON FITTINGS
54
CORLINE ENT &
KIWKON FITTINGS
COR-LINE
®
ENT & KWIKON
®
FITTINGS
Pulling Wire
Kwikon’s interior corrugated surface greatly
reduces the amount of friction while pulling
conductors through long runs, even with 90°
bends.
CSA Certified
Cor-Line Electrical nonmetallic tubing and
Kwikon fittings are certified to CSA C22.2
No. 227.1.
FT-4 Approved
IPEX Cor-Line ENT tubing meets and
exceeds the requirements of CSAs vertical
char test as described in Clause 4.11.4 of
CSA C22.2 No. 0.3M.
Direct Burial
The Canadian Electrical Code approves ENT for direct earth burial.
Rules governing installation of Cor-Line ENT are covered in the CEC
Part 1, Rule 12-1500 through 12-1516.
Installation in Noncombustible/Combustible
Construction
Refer to Section 3.1.5.19 of the National
Building Code for rules governing the use of
combustible conduit in noncombustible and/or
combustible buildings. Where provincial codes
vary, please consult with the building
authority having jurisdiction.
Nonmetallic Raceways for
Fire Alarm System Conductors
Rule 32-102 of the CEC allows Cor-Line
ENT to be used for fire alarm systems in
noncombustible or combustible buildings
provided: (1) the raceway is embedded in at
least 50mm (2 in.) of masonry or poured
concrete, and (2) where electrical
nonmetallic tubing (ENT) is used, the
transition from ENT to metal raceways is made in the concrete
using a transition fitting or other acceptable means. (Kwikon
transition fittings are specifically designed for this application.)
Ease of Installation
Engineered for the rugged day-to-day
challenges of the construction industry,
Cor-Line has already established itself as a
market leader. Requiring no special tools for
bending or cutting, Cor-Line is easily installed.
Bending & Cutting
Cor-Line’s corrugated construction allows it
to be easily bent by hand, no longer
requiring special bending equipment
traditionally required with metal conduit
systems. When bending, ensure the radius of
the curve is at least six times the internal
diameter of the tubing.
Pre-Assembly of Kwikon Slab
Boxes
IPEX’s Kwikon slab boxes are available with or
without molded connectors. For boxes without
molded connectors, pre-assembly is quick and
simple using our snap-in connector or
threaded male adapter with locknuts. Both
provide a secure concrete-tight connection.
Pre-Assembly of Metallic
Boxes
Metallic slab boxes can be quickly pre-
assembled with Kwikon connectors.
Secured with a locknut, Kwikon connectors
provide a concrete-tight connection.
Installation in Sheer Walls,
Interior Walls & Block Walls
Cor-Line’s flexibility, lightweight and ease of
handling in metal, wood, or block walls,
combined with Kwikon connectors and
couplings, substantially reduce time and
labour needed to install electrical raceways.
COR-LINE
®
ENT & KWIKON
®
FITTINGS
57
CORLINE ENT &
KIWKON FITTINGS
56
CORLINE ENT &
KIWKON FITTINGS
KWIKON
®
ENT FITTINGS
Kwikon Coupling
Size (in) Part Number Product Code Package Qty
1/2 KC10 089000 150
3/4 KC15 089001 100
1 KC20 089002 50
1-1/4 KC25 189670 30
1-1/2 KC30 189671 30
2KC35 189672 20
Kwikon Connector For
Concrete Encasement
Size (in) Part Number Product Code Package Qty
1/2 KTA10 089006 150
3/4 KTA15 089007 100
1 KTA20 089008 50
1-1/4 KTA25 189680 30
1-1/2 KTA30 189681 30
2KTA35 189682 20
Kwikon Snap-in Connector
Size (in) Part Number Product Code Package Qty
1/2 KTS10 089146 150
3/4 KTS15 089147 100
1 KTS20 089148 50
Kwikon Transition Coupling
Size (in) Part Number Product Code Package Qty
1/2 KTC10 089012 125
3/4 KTC15 089013 100
1 KTC20 089014 50
COR-LINE
®
ENT
Reel & Coil Size
Size (in) Length (ft) Product Code Weight lbs/pkg
1/2 1500 012004 185
3/4 1000 012009 145
1 750 012019 155
1-1/4 1000 012047 205
1-1/2 750 012033 180
2 500 012044 160
1/2 370 012000 37
3/4 240 012008 30
1 160 012018 28
1-1/4 500 012046 102
1-1/2 300 012032 72
2 225 012043 62
Wrapped in plastic, coils are easily dispensed from the centre.
Cor-Line Dimensions
10' Sticks
Size (in) ID (in) OD (in)
1/2 0.574 0.840
3/4 0.778 1.050
11.000 1.315
1-1/4 1.340 1.660
1-1/2 1.574 1.900
22.020 2.375
Size (in) Length (ft) Product Code Weight lbs/pkg
1/2 x 10' 3600 012005
345
3/4 x 10' 2200 012006
315
1 x 10' 1800 012007
345
Weight Comparison of Cor-Line ENT vs EMT
Size (in) ENT lbs/1000' EMT lbs/1000'
1/2 100 295
3/4 125 440
1175 668
1-1/4 185 970
1-1/2 220 1,100
2319 1,517
ReelCoil
CSA C22.2
No. 227.1
59
CORLINE ENT &
KIWKON FITTINGS
58
CORLINE ENT &
KIWKON FITTINGS
KWIKON
®
ENT FITTINGS
Kwikon Slab Box
Engineered to be rugged and durable, IPEX’s boxes will withstand
construction’s harshest environments.
Designed by contractors for contractors, Kwikon slab boxes are available
in two unique styles, with or without molded connectors. Now you can
provide a complete, nonmetallic slab system. Priced competitively with
traditional steel mud boxes, Kwikon slab boxes increase labour
efficiencies, reducing costs.
Features
Approved for use with ceiling fans up to 35 lbs. and luminaries
up to 50 lbs.
Concrete tight
All molded connectors have 360° locking tabs that exceed CSA and
UL requirements for pull-out
Molded connectors are also approved for use with Scepter Rigid
PVC Conduit
Manufactured from high impact PVC
Nonmetallic / Nonconducting / Noncorroding
Threaded brass inserts
Slab Box w/ Molded Connectors
Hub Size (in) Part Number Product Code Package Qty
8 x 1/2 SMB-H-10 089455 25
4 x 1/2, 2 x 3/4, 2 x 1 SMB-H-10/20 089456 25
4 x 1/2, 4 x 3/4 SMB-H-10/15 089457 25
8 x 3/4 SMB-H-15 089459 25
4 x 3/4, 4 x 1 SMB-H-15/20 089463 25
Slab Box w/o Molded Connectors
Knockout Size (in) Part Number Product Code Package Qty
8 x 1/2 SMB-10 089450 25
4 x 1/2, 2 x 3/4, 2 x 1 SMB-10/20 089451 25
Part
Number
Product
Code Standard Packaging
SMBR 089494 20
Slab Box Extension Ring
Adjusts height of SMB/SMBH series slab boxes by 1"
Kwikon ENT Form Stubby
Size (in) Part Number Product Code Package Qty
1/2 KSTB-10 089330 150
3/4 KSTB-15 089331 150
1 KSTB-20 089332 150
1-1/4 KSTB-25 089333 150
Kwikon ENT Multi-LinkTM
Form Stubby
Size (in) Part Number Product Code Package Qty
1/2 MSTB-10 089031 75
3/4 MSTB-15 089026 75
1 MSTB-20 089025 50
Kwikon ENT Angled Form Stubby
Size (in) Part Number Product Code Package Qty
1/2 KASTB-10 089233 50
3/4 KASTB-15 089234 50
1KASTB-20 089235 50
1-1/4 KASTB-25 089236 50
1-1/2 KASTB-30 089238 50
KWIKON
®
ENT FITTINGS
Kwikon 90oStub Down Fittings
Size (in) Part Number Product Code Package Qty
1/2 KT90-10 089060 40
3/4 KT90-15 089059 35
1 KT90-20 089058 25
KT90 Stub Down Fittings
(Kwikon x Threaded)
Size (in) Part Number Product Code Package Qty
1/2 KK90-10 089055 40
3/4 KK90-15 089056 35
1 KK90-20 089057 25
KK90 Stub Down Fittings
(Kwikon x Kwikon)
61
CORLINE ENT &
KIWKON FITTINGS
60
CORLINE ENT &
KIWKON FITTINGS
KWIKON
®
ENT FITTINGS
Tapered Plugs
Size (in) Part Number Product Code Package Qty
1/2 TP10 089003 100
3/4 TP15 089004 100
1TP20 089005 100
ENT 4" Square Box Flat Cover
Accessories
Size (in) Part Number Product Code
1/2 KO KWBC-10 089500
Kwikon Cutter & Blades
Description Part Number Product Code
Cutter (1/2"- 1") CLC20 089066
Blades for CLC20 SSB 089067
Cutter (1/2"- 2") CLC35 089068
Blades for CLC35 SB35 089069
The
NEW ENT Support Unit (ESU)
raises the tubing or conduit up off the concrete form
during the concrete pour maintaining a level raceway
and allows for maximum aggregate flow and concrete
consolidation.
Easy to use, the ESU snaps around any size of ENT.
It is perfect for use in high rise buildings constructed with post-tensioned
(PT) concrete slabs.
Features
• One size fits all 1/2" - 2"
• Saves time and labour
• Easy locking mechanism
• Securable to the concrete form
• Minimal footprint reduces amount of surface contact
Part Number Product Code
ESU-10-35 089149
KWIKON
®
ENT FITTINGS
Hub Size (in) Part Number Product Code Package Qty
8 x 1/2 SSBH-10 089452 25
8 x 3/4 SSBH-15 089453 25
4 x 1/2 & 4 x 3/4 SSBH-10/15 089454 25
4" Square Slab Box
Hub Size (in) Part Number Product Code Package Qty
8 x 1/2 SMBS-H-10 089485 20
4 x 1/2 & 4 x 3/4 SMBS-H-10/15 089486 20
8 x 3/4" SMBS-H-15 089487 20
4 x 1/2, 2 x 3/4, 2 x 1 SMBS-H-10/20 089488 20
4 x 3/4 & 4 x 1 SMBS-H-15/20 089489 20
Shallow Slab Box
Hub Size (in) Part Number Product Code
4 x 1/2, 4 x 3/4 SVDB-H-10/15 089496
4 x 3/4, 4 x 1 SVDB-H-15/20 089049
4 x 1/2, 2 x 3/4, 2 x 1 SVDB-H-10/20 089052
8 x 3/4 SVDB-H-15 089065
Kwikon Concrete 3-1/2"
Deep Concrete Wall Box
Hub Size (in) Part Number Product Code
4 x 1/2 SVSB-H-10 089054
4 x 3/4 SVSB-H-15 089053
Kwikon 2" Shallow
Concrete Wall Box
Concrete Wall Boxes
• Fully assembled and installation ready
• Perfectly suited for deep or shallow construction preferences
• Concrete-tight poly film covering the box opening
• Kwikon hubs do not protrude inside the box
63
SUPERDUCT
Super Duct Pipe and Fittings
Super Duct is recognized by major utilities, contractors and engineering
firms as the premier ducting product available on the market.
Super Duct is manufactured with a specialized compound and
engineered for high impact and crush strength specifically required by
utilities for underground duct. This compound enhances the friction
coefficient of Super Duct for easier pulling of conductors/wires
through long runs.
Rigid Super Duct (Type DB-2) conforms to the testing requirements of
CSA Standard C22.2 No. 211.1 both for encasement in
concrete/masonry and for direct burial.
CSA C22.2
No. 211.1
SUPER DUCT®PIPE & FITTINGS
&MUCH MORE ...
DOWNLOAD
OUR SCEPTER ELECTRICAL
CATALOGUE OR OUR
ELECTRICAL POCKET PRO
ONLINE TRAINING
TECHNICAL DOCUMENTS
PRODUCT INFO
Visit our website:
www.ipexelectrical.com
+
65
SUPERDUCT
64
CORLINE ENT &
KIWKON FITTINGS
INSTALLATION
Field Bending
The natural flexibility of IPEX Super Duct allows field bending, so
minor changes in elevation or direction can often be accommodated
without the use of special sweeps or fittings. The following table
indicates typical maximum offset bends that can be achieved by
“cold bending.”
Offset
Allowable Offset for Super Duct
NOTES:
1. Axial deflection should not be attempted at the joints.
2. The above values were established for ambient temperatures
above the freezing point. Increased radii may be desirable at
below-freezing temperatures.
Size Max Allowable Offset
10' Length
Max Allowable Offset
20' Length
in. mm in. mm in.mm
250 20 508 79 2 007
375 14 356 56 1 422
3-1/2 90 12 305 49 1 245
4100 11 279 43 1 092
5125 7178 35 889
6150 7178 29 737
ENGINEERING DATA
Lightweight
Super Duct is easy to carry and
install, reducing labour and costs.
Long Lengths
Super Duct is available in 10' and
20' lengths, minimizing the
number of connections needed.
Bell Ends
Super Duct is bell-ended, allowing
for easy assembly in the field.
High Compressive
Strength
Super Duct’s specially formulated compound is designed to withstand
high loads.
Low Coefficient of Friction
The smooth bore of Super Duct facilitates cable pulling and eliminates
costly cable damage.
Quality Control
Stringent, continuous testing ensures that Super Duct is a consistently
high quality product.
Note: Super Duct meets or exceeds all CSA requirements.
Super Duct (Type DB-2)
Description CSA Requirements Reference
Pipe Stiffness @ 5% 43.5 psi (300 kPa) CSA C22.2 No. 211.1
Crush Resistance 198 lbs. @ 73°F (90 kg @ 23°C)
10% max. residual deflection CSA C22.2 No. 211.1
Impact Resistance 45 ft. lbf @ 73°F (61J @ 23°C)
25 ft. lbf @ 0°F (34J @ -18°C) CSA C22.2 No. 211.1
Residual Stress
149°F (65°C) for 4 hours.
Allow to cool to 73°F (23°C).
0.5% shrinkage allowed.
CSA C22.2 No. 211.1
Joint Tightness 5 psi (35 kPa) internal water
pressure applied for 24 hours. CSA C22.2 No. 211.1
67
SUPERDUCT
66
SUPERDUCT
Concrete Encased Duct Installation
For multipurpose power cable and communication duct banks,
spacing between ducts is critical for optimum performance. IPEX
has designed the Monobloc and Vertical Lok
Spacer systems to accommodate all
specification and field installations.
These light weight spacers provide the vertical
and horizontal separation required in a trench.
With spacers in place on the trench bottom,
lay the first tier of ducts. When using a
concrete base, lay the bottom tier before the
base has taken initial set. Place subsequent
tiers of spacers on top of the tier until the
required number of ducts are installed. Then
tie the entire assembly together. It is not
necessary to weight or brace the bank unless
the concrete mix is very wet.
The Concrete Pour
Do not allow a heavy mass of concrete to fall directly onto the duct. If
this is a possibility, use a plank to direct the concrete down the sides
of the bank assembly to the trench bottom. The concrete will flow to
the centre of the bank and rise up in the middle, uniformly filling all
open spaces. Voids can be eliminated by carefully working a long, flat
slicing bar or spatula up and down between the vertical rows of ducts.
Concrete should then flow between and under all of the ducts.
Duct Bank Elevation
Monobloc spacers should be staggered. It is recommended that
spacers be located approximately one-fifth of duct length from each
end. Vertical Lok spacers should be located to a maximum of every
5.5 ft. (1.7m).
Backfilling
Backfill with regular excavated soil after the concrete has set.
INSTALLATION
90° 45° 221/2°
Bends
Standard 90°, 45° and 22 1/2° bends are available from sizes 2"
through to 6" in 24", 36", 42" and 60" radius. All bends are supplied
with 6" (15.2cm) tangents. The centre line lay length (L) can be
calculated using;
L=(πr x §
180 )+ 2 (tangent)
Where: π=3.14
L = centre line lay length
r = radius of bend
§ = angle of bend
tangent = 6"
Example: for a 3" 90° bend with a 36" radius - calculate the lay length:
L=(3.14 x 36 x 90°
180°)+ 2 (6)
L = 69 inches
L (metres) = L imperial = 69" = 1.75m
12 x 3.281 39.37
INSTALLATION
Static Friction Coefficient
Ducting Materials
.0 .1 .2 .3 .4 .5 .6 .7 .8
PVC
RTRC
69
SUPERDUCT
68
SUPERDUCT
INSTALLATION
Direct Burial Installation
Trench Bottom
The trench bottom should provide a
continuous, firm and uniform support for the
duct bank construction. Care should be
taken to avoid lumps, ridges, depressions
and stones causing “point” contacts or
uneven bearing.
Rock or Shale
Excavate 3" below the desired depth and bring the trench back to
grade with selected tamped soil. This will provide the duct with a
uniform bedding surface.
Unstable Soils
Tests should be conducted to establish the soil strength in marshy or
swampy areas. It may be necessary in these conditions to dig deeper
and refill with crushed stone or gravel, or to employ mats, timbers or a
concrete base.
Placement of Duct
After the first tier of ducts is installed, backfill and compact as
outlined below. If wood combs are employed for spacing, remove them
as the backfill is placed and tamped. Then begin the next tier.
Initial Backfilling
1. Fit side and centre to the top of the ducts. Use a hand tamper only
to tamp firmly.
2. Backfill over the duct to the required thickness (see note) and
tamp firmly, using only a hand tamper.
Final Backfilling
When the last tier is placed, hand-place the backfill to 4" over the
duct with soil that does not contain stones larger than 3/8". Hand-
tamping of this layer is optional, depending on the specifications.
From this point, backfill may be completed by hand or by pneumatic
tamping in layers from 4" to 12" depending on the degree of
compaction desired.
When placing backfill by machine, avoid the use of large rocks until a
protective layer (minimum of 12") is established.
Note: In direct burial, no spacer should be used with Type 2; spacers provide “point” support
instead of the continuous bed required. Backfill thickness between ducts is usually 2" to 3".
INSTALLATION
Concrete Encased Tier-by-Tier
Installation
The advantage of this method is the production
of a solid, void-free concrete envelope. Simply
pour each tier independently.
Trench Bottom
After grading the trench, place a foundation of
3" of concrete on the bottom. It should be
smooth and graded.
Bank Assembly
Lay the bottom tier of ducts on the
concrete base. Ducts should be spaced with
wooden combs (two per duct length).
Concrete the first tier level to the top of the
comb. Remove combs and fill the voids.
Light tamping will ensure an even surface.
Repeat this sequence until the bank is built up.
Concreting
If the concrete is allowed to set before assembling the next tier, the
concrete will be stronger and more dense and the ducts will be
aligned straighter. One problem with this method is that the bank will
be in a
series of layers and therefore more likely to heave and
separate under frost conditions. If successive tiers are laid before the
concrete has set, a satisfactory bond will be achieved by tamping the
dry concrete.
Backfilling
Backfill with regular excavated soil when the bank is complete.
Duct is usually laid in 100' sections once the trench is excavated.
Therefore, concreting can be a continuous process.
Cross-section of
tier-by-tier method.
Type of wood comb used.
100'
100'
100'
100'
100'
71
SUPERDUCT
70
SUPERDUCT
SUPER DUCT
®
FITTINGS
PVC Coupling - Solvent Weld
Dimension (in) Part Number Product Code
2SWC020 029001
2 (long) SWC020L 029009
3 SWC030 029002
3-1/2 SWC035 029003
4SWC040 029004
5SWC050 029005
6SWC060 029006
Polyethylene Coupling – Push Fit
PVC 5° Coupling – Solvent Weld
Dimension (in) Part Number Product Code
25ACS20 029041
35ACS30 029042
3-1/2 5ACS35 029043
45ACS40 029044
55ACS50 029045
65ACS60 029046
Polyethylene 5° Coupling – Push Fit
Dimension (in) Part Number Product Code
35APF30 029030
3-1/2 5APF35 029502
45APF40 029998
55APF50 029050
Dimension (in) Part Number Product Code
2PFC020 029011
3PFC030 029012
3-1/2 PFC035 029013
4PFC040 029014
5PFC050 029015
6PFC060 029016
SUPER DUCT
®
PIPE
CSA Type II
Dimension
(in)
10' L Belled
Product Code Ft/Crate 20' L Belled
Product Code Ft/Crate Weight/100'
(lbs)
2 008220 2,460 08221 4,920 33.7
3 008230 1,120 08231 2,240 61.2
3-1/2 008235 810 08236 1,620 77.3
4 008240 630 08241 1,260 99.2
5 008250 430 08251 860 159.6
6008260 280 08261 560 226.6
CSA Type II Split Duct
Dimension (in) Product Code Ft/Crate Weight/100' (lbs)
2 008222 2,460 33.7
3 008232 1,120 61.2
3-1/2 008237 810 77.3
4 008242 630 99.2
5008252 430 159.6
6008262 280 226.6
Super Duct Dimensions in Inches
Duct Diameter Minimum ID Nominal Wall Average OD
2 2.001 .082 2.250
3 3.000 .097 3.250
3-1/2 3.480 .109 3.730
4 3.941 .120 4.216
54.974 .153 5.299
65.896 .180 6.275
Super Duct Dimensions in Millimetres
Duct Diameter Minimum ID Nominal Wall Average OD
50 50.83 2.08 57.15
75 76.20 2.46 82.55
90 88.39 2.77 94.74
100 100.10 3.05 107.09
125 126.34 3.89 134.60
150 149.76 4.57 159.39
73
SUPERDUCT
72
SUPERDUCT
Terminator with Knock-Out Plugs
Dimension (in) Part Number Product Code
3TERM30 029826
3 1/2 TERM35 029523
4 (with holes) TERM40H 029822
4 (no holes) TERM40W 029827
Cap – Solvent Weld
Dimension (in) Part Number Product Code
2SWCA20 029071
3SWCA30 029072
3-1/2 SWCA35 029073
4SWCA40 029074
5SWCA50 029075
6SWCA60 029076
90° Long Sweep Bend
Dimension (in) Part Number Product Code
2 x 24 R 902024 029091
2 x 36 R 902036 029092
2 x 60 R 902060 029036
3 x 24 R 903024 029055
3 x 36 R 903036 029093
3 x 60 R 903060 029134
3-1/2 x 24 R 903524 029123
3-1/2 x 36 R 903536 029094
3-1/2 x 60 R 903560 029135
4 x 24 R 904024 029047
4 x 36 R 904036 029095
4 x 60 R 904060 029096
5 x 42 R 905042 029097
5 x 60 R 905060 029037
6 x 60 R 906060 029098
SUPER DUCT
®
FITTINGSSUPER DUCT
®
FITTINGS
Expansion Joint
Dimension (in) Part Number Product Code
2EXPJ20 029151
3EXPJ30 029152
3-1/2 EXPJ35 029153
4EXPJ40 029154
Reducer Coupling – Solvent Weld
Dimension (in) Part Number Product Code
3 x 2 RC3020 029021
3-1/2 x 2 RC3520 029039
3-1/2 x 3 RC3530 029022
4 x 2 RC4020 029023
4 x 3 RC4030 029024
4 x 3-1/2 RC4035 029025
5 x 4 RC5040 029026
6 x 4 RC6040 029027
Split Wye – Solvent Weld
Dimension (in) Part Number Product Code
2SPLY20 029051
3SPLY30 029052
3-1/2 SPLY35 029053
4SPLY40 029054
PVC Bell Ends
Dimension (in) Part Number Product Code
2BELL20 029061
3BELL30 029062
3-1/2 BELL35 029063
4BELL40 029064
5BELL50 029065
6BELL60 029066
75
SUPERDUCT
74
SUPERDUCT
SUPER DUCT
®
FITTINGS
Note: Duct to RTRC Conduit Adapters are available on request.
Universal Pipe Plug
Dimension (in) Part Number Product Code
2 & 2-1/2 UPP35 077433
3 & 3-1/2 UPP45 077434
4UPP55 077435
5UPP60 077436
6UPP65 077437
Female Adapter
Dimension (in) Part Number Product Code
2FEMA20 029141
3FEMA30 029142
3-1/2 FEMA35 029143
4FEMA40 029144
5FEMA50 029145
6FEMA60 029146
Sleeve
Conduit to Duct Adapter
Dimension (in) Part Number Product Code
2ARIG20 029181
2 (long) ARIG20L 029188
3ARIG30 029182
3-1/2 ARIG35 029183
4ARIG40 029184
5ARIG50 029185
6ARIG60 029186
Conduit
Socket
Duct
Socket
SUPER DUCT
®
FITTINGS
Note: Special radius bends are available upon request.
45° Long Sweep Bend
Dimension (in) Part Number Product Code
2 x 24 R 452024 029111
2 x 36 R 452036 029112
3 x 24 R 453024 029082
3 x 36 R 453036 029113
3-1/2 x 36 R 453536 029114
4 x 24 R 454024 029128
4 x 36 R 454036 029115
4 x 60 R 454060 029116
5 x 42 R 455042 029117
6 x 60 R 456060 029118
22 1/2° Long Sweep Bend
Dimension (in) Part Number Product Code
3 x 36 R 223036 029085
4 x 36 R 224036 029204
5 x 42 R 225042 029249
Tapered Plug
Dimension (in) Part Number Product Code
2PLUG20 029131
3PLUG30 029132
3-1/2 PLUG35 029133
4PLUG40 029078
5PLUG50 029079
6PLUG60 029136
77
SUPERDUCT
76
SUPERDUCT
Monobloc Spacer Benefits for Telephone Duct:
lightweight; easy to handle
and install
• weatherproof
resilient at extremely low
temperatures
flexible, yet tough
readily available in a wide
range of sizes and
configurations
• economical
immune to corrosion attack
approved by Bell Canada
versatile, as they can be used as both a base & intermediate spacer
MONOBLOC
SPACERS
B
B
D
C
Selection Table (in inches)
Nominal Size Vertical
Spacing
Horizontal
Spacing
Ground
Clearance
Number of
Ways
(A) (B) (C) (D) (E)
21-1/2 1-1/2 3 2
31-1/2 1-1/2 3 2
3-1/2 1 1 2 2 - 3 - 4
4 1 1 2 1 - 2 - 3 - 4
41-1/2 1-1/2 32 - 3 - 4
4 2 2 3 1 - 2 - 3 - 4
4 3 3 3 2 - 3 - 4
4 3 3 4 2 - 3 - 4
4-1/2 2 2 3 1 - 2 - 3
51-1/2 2-1/8 3-5/8 1
51-1/2 1-1/2 32 - 3 - 4
12
34
* Do not have rebar slots or base holes
SUPER DUCT
®
FITTINGS
Reducing Adapter Coupling –
Duct to PVC Conduit
Dimension (in) Part Number Product Code
3 x 2 ARIG3020 029191
4 x 2 ARIG4020 029192
4 x 3 ARIG4030 029187
PVC Adapter Coupling – Asbestos
Cement or Bituminous Fibre
Dimension (in) Part Number Product Code
3-1/2 ACFB35 029163
4ACFB40 029164
Vertical-Lok
Spacers
Intermediate Base
Dimension (in) Part Number Product Code Part Number Product Code
2 x 1-1/2 IS3530 029550 BS3530 029566
2 x 2 IS3535 029551 BS3535 029567
2 x 3 IS3545 029552 BS3545 029568
*
3 x 1-1/2 IS4530 029553 BS4530 029569
3 x 2 IS4535 029554 BS4535 029570
3 x 3 IS4545 029555 BS4545 029571
*
4 x 1 IS5520 029556 BS5520 029572
4 x 1-1/2 IS5530 029557 BS5530 029573
4 x 2 IS5535 029558 BS5535 029574
4 x 3 IS5545 029559 BS5545 029575
*
5 x 1-1/2 IS6030 029560 BS6030 029576
5 x 2 IS6035 029561 BS6035 029577
5 x 3 IS6045 029562 BS6045 029578
6 x 1-1/2 IS6530 029563 BS6530 029579
6 x 2 IS6535 029564 BS6535 029580
6 x 3 IS6545 029565 BS6545 029581
*
8 x 2 IS8035 029294 BS8035 029293
79
SCEPTACON
78
SUPERDUCT
SceptaConTM Trenchless Raceway Systems
SceptaCon is one of the first PVC systems designed for the rigors of
trenchless applications. It links seamlessly to existing PVC conduit
infrastructures and allows utility companies to standardize on PVC
throughout their entire electrical systems.
SceptaCon's slide-in locking system and pre-installed, pre-lubricated
gaskets allow contractors to create a water-tight seal by hand in
seconds - in all temperatures - without having to worry about solvents
or chemicals freezing or drying too quickly.
Its unique spline-lock snaps into a recessed opening, ensuring the
spline won't get snagged during pull-through. SceptaCon's rounded
bell shoulders slide easily past roots, rocks and other debris in the
borehole, ensuring a smooth, easy installation. And because
SceptaCon is made to the same high standards as our Scepter rigid
PVC conduit, contractors and electrical utilities can be assured of the
same level of quality - above ground and below.
79
SCEPTACONTM TRENCHLESS RACEWAY SYSTEMS
MONOBLOC
®
SPACERS
Monobloc Duct Spacers
Description (in)
A, B, C, D EProduct
Code
Dimensional
Drawing
F length
(in)
2 x 1-1/2 x 1-1/2 x 3 2 way 029473 27.9
3 x 1-1/2 x 1-1/2 x 3 2 way 029474 210.3
3-1/2 x 1 x 1 x 2 2 way 029860 212.4
3-1/2 x 1 x 1 x 2 3 way 029861 217.3
3-1/2 x 1 x 1 x 2 4 way 029479 220.9
4 x 1 x 1 x 2 1 way 029475 28.3
4 x 1 x 1 x 2 2 way 029476 213.5
4 x 1 x 1 x 2 3 way 029477 218.8
4 x 1 x 1 x 2 4 way 029478 224.2
4 x 1-1/2 x 1-1/2 x 3 2 way 029470 114.2
4 x 1-1/2 x 1-1/2 x 3 3 way 029471 120.0
4 x 1-1/2 x 1-1/2 x 3 4 way 029472 126.0
4 x 2 x 2 x 3 1 way 029480 28.3
4 x 2 x 2 x 3 2 way 029464 114.5
4 x 2 x 2 x 3 3 way 029465 120.7
4 x 2 x 2 x 3 4 way 029499 127.0
4 x 3 x 3 x 3 (Base) 2 way 029466 315.0
4 x 3 x 3 x 3 (Base) 3 way 029488 322.5
4 x 3 x 3 x 3 (Base) 4 way 029489 330.0
4 x 3 x 3 x 4 2 way 029469 115.0
4 x 3 x 3 x 4 3 way 029497 122.5
4 x 3 x 3 x 4 4 way 029498 130.1
4-1/2 x 2 x 2 x 3 1 way 029485 28.7
4-1/2 x 2 x 2 x 3 2 way 029486 215.5
4-1/2 x 2 x 2 x 3 3 way 029487 222.2
5 x 1-1/2 x 2-1/8 x 3-5/8 1 way 029455 47.0
5 x 1-1/2 x 1-1/2 x 3 2 way 029494 216.2
5 x 1-1/2 x 1-1/2 x 3 3 way 029495 223.1
5 x 1-1/2 x 1-1/2 x 3 4 way 029496 230.0
81
KWIKPATH
80
SCEPTACON
Kwikpath®Optical Fibre & Communication
Cable Raceway Systems
Kwikpath comes together faster and easier than other raceway
systems, thanks largely to a patented "snap-on" design that ensures
fittings and raceway assemble and terminate easily with no special
tools or handling equipment needed. The six locking tabs keep the
fitting tightly connected with tremendous pull-out resistance. All
without messy cementing or screws to tighten.
With its handy coil lengths delivered in dual purpose protective
packaging/pull box, Kwikpath makes home-run systems easy and
economical, letting you run cable from your telecommunications box
directly to a workstation outlet with fewer couplings. Being able to cut
to length on the job site ensures that you don't run short or have
wasted conduit left over.
Whether in narrow shafts or tight plenums, its lightweight and fast,
trouble-free installation make Kwikpath the number one choice for
commercial and residential cable management.
Codes & Standards
• EIA/TIA
CEC 2002/NBC
• NFPA
Plenum FT6
Riser FT4
General Purpose FT1
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
SCEPTACONTM TRENCHLESS RACEWAY SYSTEMS
No Cementing or Lubrication
SceptaCon’s slide-in locking system and pre-
installed, pre-lubricated gaskets allow contractors
to create a water-tight seal by hand in seconds.
Outperforms Other PVC
Products
SceptaCon’s unique spline-lock snaps into a
recessed opening, ensuring the spline won’t
get snagged during pull-through. SceptaCon’s
rounded bell shoulders slide easily past roots,
rocks and other debris in the borehole,
ensuring a smooth, easy installation.
No Fusion Required
Because SceptaCon’s joints can be quickly
joined by hand in seconds, crews don’t need
large, expensive fusion equipment or special
training to create water-tight joints. In addition,
SceptaCon can be assembled one pipe length
at a time, then pulled underground, eliminating
the need for long strings of pipe on the job.
Superior Performance
SceptaCon is made from durable schedule 40 PVC that’s resistant to
creasing, scoring or flattening when pulled past obstructions in the
borehole, yet flexible enough to bend with underground twists and
turns. SceptaCon remains round, unlike HDPE which can stretch and
become oval.
Easy to Handle
SceptaCon is available in convenient 10' and 20' lengths that are
light-weight, easy to handle and no problem to work with in all types
of weather.
Length Product Code
3" x 10' 106330
3" x 20' 106331
4" x 10' 106340
4" x 20' 106341
5" x 10' 106350
5" x 20' 106351
6" x 10' 106360
6" x 20' 106361
SceptaConTM Raceway
83
KWIKPATH
82
KWIKPATH
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
Plenum Coil with Pull Tape
Kwikpath Plenum Raceway
Kwikpath Plenum is made from a UL approved compound and like
Kwikpath Riser, forms nonmetallic, flexible corrugated cable raceways.
Vibrant orange in colour, Kwikpath Plenum meets the UL tests on
flame propagation and smoke density with values well below the
standard requirements. This heat/smoke-resistance makes it an ideal
raceway to run Optical Fiber Cables (OFPN) and/or Communication
Cables (CMP/CMP-OF) through plenums and other spaces used for
environmental air. Kwikpath Plenum comes with
sequential markers every foot.
Size Length Part Number Product Code
3/4" 200' KPP075TC 124020
1" 200' KPP100TC 124011
1-1/4" 200' KPP125TC 124012
1-1/2" 200' KPP150TC 124013
2" 200' KPP200TC 124014
Size Length Part Number Product Code
3/4" 1000' KPP075TR 124021
1" 1000' KPP100TR 124015
1" 2500' KPP100TR48 124022
1" 5000' KPP100TR72 124023
1-1/4" 1000' KPP125TR 124016
1-1/4" 4000' KPP125TR72 124024
1-1/2" 750' KPP150TR 124017
2" 500' KPP200TR 124018
Plenum Reel with Pull Tape
Also available without pull tape - minimum quantity required.
Also available without pull tape - minimum quantity required.
Compliance to Building
Regulations
Kwikpath meets all building regulations
and is the only fully approved raceway and
fitting combination on the market.
A Fitting Choice
The Kwikpath fitting system reduces the
need for pulling long runs of raceway
around awkward corners and tight spaces.
And the industry first Y-Coupler reduces the
number of pull boxes required in your
system design.
Installation Friendly
Packaging
200' coils are packaged individually in
corrugated boxed cartons for ease of
handling and dispensing. Designed into the
cartons are packaging features that assist
with moving and dispensing the product. By
using the dispensing method, only the
necessary product amount is withdrawn
from the carton with the balance being
contained and easily managed.
Reduces Costs Now and
Over Long Term
Kwikpath is designed to allow easier cable
installation and removal than other careway
systems. Simply pull cables through the
raceway – no more fishing new cables
blindly through walls or ceilings. Kwikpath
also reduces renovation costs by
eliminating the need to remove existing
cabling in retrofit applications.
Protects Cable Integrity and
Performance
Kwikpath prevents cables from being
damaged on edges or snags as they’re
pulled through the raceway. Once cables
are installed, Kwikpath offers flame resisting properties and its
protective shell prevents damage to cables when renovations cause
tradesmen to enter or change the walls or ceilings.
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
NBC
CEC
85
KWIKPATH
84
KWIKPATH
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
Kwikpath Riser Raceway
The backbone of the structured cabling syste, Kwikpath Riser is a
nonmetallic, flexible PVC corrugated product manufactured and tested
specifically for riser applications. Easily identified by its mandarin
orange color, it’s available in convenient coil
or reel packaging with squential markers
every foot.
Riser Coil with Pull Tape
Size Length Part Number Product Code
3/4" 200' KPR075TC 125026
1" 200' KPR100TC 125011
1-1/4" 200' KPR125TC 125012
1-1/2" 200' KPR150TC 125013
2" 200' KPR200TC 125014
Size Length Part Number Product Code
3/4" 1000' KPR075TR 124027
1" 1000' KPR100TR 125015
1" 2500' KPR100TR48 125023
1" 5000' KPR100TR72 125025
1-1/4" 1000' KPR125TR 125016
1-1/4" 4000' KPR125TR72 125024
1-1/2" 750' KPR150TR 125017
2" 500' KPR200TR 125018
Riser Reel with Pull Tape
Also available without pull tape - minimum quantity required.
Also available without pull tape - minimum quantity required.
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
Plenum Coupling
Kwikpath Plenum Fittings
Kwikpath Plenum fittings are molded from approved material to be
used with Kwikpath Plenum raceway meeting all Standards requirements.
Size Part Number Product Code
3/4" KPPC075 132650
1" KPPC100 132651
1-1/4" KPPC125 132652
1-1/2" KPPC150 132653
2" KPPC200 132654
Size Part Number Product Code
3/4" KPTA075 132660
1" KPTA100 132661
1-1/4" KPTA125 132662
1-1/2" KPTA150 132663
2" KPTA200 132664
Plenum Terminal Adapter c/w Lockout
87
KWIKPATH
86
KWIKPATH
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
Resi Coil Empty
Kwikpath Resi Raceway
Kwikpath Resi is a flexible raceway system
created especially for residential
communications systems, arranging and
organizing telephone, ethernet, satellite,
internet, video, security and sound cabling.
Resi Reel Empty
Kwikpath Resi Fittings
Kwikpath Resi couplings and terminal
adapters are available in 3/4" to 2" sizes and
are also Kwikpath Riser fittings.
Refer to Kwikpath Riser Part Numbers.
Size Length Part Number Product Code
3/4" 200' KPH075C 127001
1" 200' KPH100C 127002
1-1/4" 200' KPH125C 127003
1-1/2" 200' KPH150C 127004
2" 200' KPH200C 127005
Size Length Part Number Product Code
3/4" 1000' KPH075R 127006
1" 1000' KPH100R 127007
1-1/4" 1000' KPH125R 127008
1-1/2" 750' KPH150R 127009
2" 500' KPH200R 127010
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
Riser Coupling
Kwikpath Riser Fittings
Made from the same material as Kwikpath Riser Raceway.
Riser Terminal Adapter c/w Lockout
Size Part Number Product Code
3/4" KPRC075 132655
1" KPRC100 132656
1-1/4" KPRC125 132657
1-1/2" KPRC150 132658
2" KPRC200 132659
Size Part Number Product Code
3/4" KRTA075 132665
1" KRTA100 132666
1-1/4" KRTA125 132667
1-1/2" KRTA150 132668
2" KRTA200 132669
88
KWIKPATH
KWIKPATH®COMMUNICATION RACEWAY SYSTEMS
Kwikpath Y-Coupler
Size Part Number Product Code
3/4" to 2" KPPY075-200 132011
Riser / Resi Straps
Size Part Number Product Code
3/4" KPS075 132006
1" KPS100 132007
1-1/4" KPS125 132008
1-1/2" KPS150 132009
2" KPS200 132010
The Y-Coupler is a fitting designed to allow
contractors to branch off from any size (3/4" to 2")
– new or existing – corrugated communication
raceway. Manufactured in traditional Kwikpath
vibrant orange, the Y-Coupler is ideal for use
in high-rise residential and commercial building
applications.
Seal End Plugs
Size Part Number Product Code
3/4" SEP075 132000
1" SEP100 132001
1-1/4" SEP125 132002
1-1/2" SEP150 132003
2" SEP200 132004
For temporary and long-term closure of raceway
ends, the insertion of sealing end plugs ensures
the raceway conduit remains clean and ready for
future needs.
Manufactured of the same material as
Riser/RESI raceway, Kwikpath pipe straps allow
for compliance with installation requirements providing for the proper
support of Riser/RESI raceways.
Company
Name
Title
Address
City Province Postal Code
Phone ext.
Fax Email / Website
This is a:
Home Address Business Address Jobsite Address
Business Type:
(check 1 or 2 that best apply)
SIC or industry sector:
My primary markets are (check all that apply):
PLEASE PRINT
Register your Pocket Pro today!
Fax this form to (905) 403-1124 and we’ll add
you to our mailing list.
Toll Free: (866) 473-9462
Fax: (905) 403-1124
Website: www.ipexelectrical.com
IPEX
2441 Royal Windsor Drive
Mississauga, Ontario
L5J 4C7
Commercial
Residential
Industrial
Other
Utility
OEM
Institutional
Company classification:
Distributor/Wholesaler
Engineering Firm
Contractor
Government
OEM - Products manufactured:
Other
CUSTOMER SERVICE CENTRES
Vancouver
Tel (604) 534-8631
Fax (604) 534-7616
Calgary
Tel (403) 236-8333
Fax (403) 279-8443
Edmonton
Tel (780) 415-5300
Fax (780) 415-5358
Winnipeg
Tel (204) 633-3111
Fax (204) 633-3075
Toronto
Tel (905) 670-7676
Fax (905) 670-5295
Montreal
Tel (514) 337-2624
Fax (514) 337-7886
Saint John
Tel (506) 633-7473
(PIPE)
Fax (506) 633-8720
St. John’s
Tel (709) 747-7473
(PIPE)
Fax (709) 368-9111
Toll Free 1-866-473-9462 (IPEXINC)
www.ipexelectrical.com
About the IPEX Group of Companies
As leading suppliers of thermoplastic piping systems, the IPEX Group of
Companies provides our customers with some of the world’s largest and
most comprehensive product lines. All IPEX products are backed by more
than 50 years of experience. With state-of-the-art manufacturing facilities
and distribution centers across North America, we have established a
reputation for product innovation, quality, end-user focus and performance.
Markets served by IPEX group products are:
Electrical systems
Telecommunications and utility piping systems
PVC, PVCO, CPVC, PP, ABS, PEX, FR-PVDF & PE pipe & ftgs (1/4" to 48")
Industrial process piping systems
Municipal pressure and gravity piping systems
Plumbing and mechanical piping systems
PE Electrofusion systems for gas and water
Industrial, plumbing and electrical cements
Irrigation systems
CTELNAIP090805 © 2010 IPEX EL004C
This literature is published in good faith and is believed to be reliable.
However, it does not represent and/or warrant in any manner the
information and suggestions contained in this brochure. Data presented is
the result of laboratory tests and field experience.
A policy of ongoing product improvement is maintained. This may
result in modifications of features and/or specifications without notice.
Products are manufactured by IPEX Electrical Inc.
Cor-Line
®, FiberTel®, Kwikon®, Kwikpath®, Monobloc®, SceptaConTM,
SceptalightTM and SuperDuct®are trademarks of IPEX Branding Inc.

Navigation menu