Cover 68684 Catalog

2014-10-22

: Pdf 68684-Catalog 68684-Catalog Batch9 unilog

Open the PDF directly: View PDF PDF.
Page Count: 12

DIMMING FACTS
FOR LED PRODUCTS
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
1
DIMMING FACTS
FOR LED PRODUCTS
Introduction
Liton offers five dimmable driver options for its product lines: incandescent, electronic low voltage, magnetic low voltage,
Hi-Lume and 0-10V. The following pages will help to explain the uses, benefits and limitations of each dimming system.
Not all dimming options are available for all products. Please consult our website at: www.liton.com for available options.
LED Dimming Driver Terminology:
Efficacy: The efficacy or efficiency of a lighting fixture is the amount of light (lumens) per unit
of energy (watts). Lm/watts = efficacy
ELV – type dimmer: An electronic low voltage dimmer used with electronic low voltage LED drivers. Also
known as a trailing-edge dimmer.
MLV – type dimmer: A magnetic low voltage dimmer used with magnetic low voltage drivers
Ghosting: When an LED lighting fixture continues to glow in the off position. This is usually due
to mismatched driver and dimmer technology, ex: incandescent dimmer paired with
an electronic low voltage driver.
Leading-edge Dimmer: A dimmer that was designed to work with Incandescent lamps. Older dimmers of this
type were not designed to work with LED lamps and problems with flicker, pop-on
and ghosting due to residual voltage have been observed. Newer designs have
been specially designed to eliminate these problems.
LED Driver: An electrical device that converts line voltage power to a power level that low voltage
LEDs can use, much like a low voltage transformer converts line voltage power
(120VAC) to low voltage (12VDC) so that it can be used with 12V MR16 lamps.
LED Dimmable Driver: An LED driver that provides the correct power to the LEDs so that it can function and
also allows the lumen output to be dimmed to create mood, ambience or to save
energy.
Light Emitting Diode (LED): A low voltage semiconductor device that emits light when electrical current is passed
through it.
Pulse Width Modulation (PWM): A method most LED drivers use to regulate the amount of power to the LED. PWM
turns LEDs on and off at high frequency, reducing the total ON time to achieve a
desired dimming level without visible flicker.
Reverse Phase Dimmers: Also known as ‘Trailing-edge’ were designed to work with most electronic (ELV) and
3-wire CFL dimmers
Trailing-edge Dimmer: A type of dimmer that was designed for use with most electronic low voltage (ELV)
and 3-wire CFL dimmers.
Standard Phase Dimmers: Also known as ‘Leading-edge’ were designed for use with Incandescent products.
Qualified Partners:
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)2
DIMMING FACTS
FOR LED PRODUCTS
Incandescent Dimming Driver Option
History
Incandescent Dimmers were designed for use with Incandescent (120V) lighting fixtures that use A19 bulbs and PAR type
lamps. They are the least expensive and most widely installed dimmers in the marketplace. They are also known as
Leading Edge Dimmers or Triac Dimmers.
Where Used?
LITON offers 2-wire incandescent compatible drivers in many of its 4", 5" and 6" General Purpose Recessed Housings
and its 2", 3" and 4" Mini-Arc Recessed Housings and are specified as “-DIN” when ordering. Please see specification
sheets for further details.
Synonymous Terms:
Incandescent, Leading Edge, 2-Wire and Triac Dimmers, Forward Phase.
Benefits
• Incandescent LED drivers work with most 2-wire incandescent dimmers making them perfect for many retrofit
applications.
• Liton’s incandescent drivers are specially designed to eliminate the problems associated with using incandescent
dimmers with LED fixtures including flicker and ghost imaging in power off mode.
• Incandescent dimmers are the least expensive and have the most installations in the marketplace.
Limitations
• Incandescent dimmers should not be used with ELV or MLV drivers because doing so could cause any of the
following malfunctions: dimmer buzz, lamp flicker, interaction between circuits or radio frequency interference
(RFI).
Incandescent Dimmer Wiring Diagram Partial list of factory tested,
compatible incandescent dimmers:
Manufacturer Style Model
Lutron Skylark S600PR
Lutron Diva DVSCCL-153P
Lutron Diva DV600PR
Leviton Illumatech IP106 (600W)
Hunt Simplicity PS-LED-PC
Hot
Neutral
Black Red
INCANDESCENT
DIMMER
120V
60Hz
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
Electronic Low Voltage (ELV) Dimming
History
Electronic Low Voltage (ELV) Dimmers were originally designed to control Electronic Low Voltage Transformers used in
low voltage (12V) MR16 type fixtures. ELV dimmers and transformers are more expensive but offer quieter operation,
better control and tend to last longer than Magnetic Low Voltage Transformers (MLV). Also referred to as Reverse Phase
Dimmers.
Where Used
ELV Dimming Option is used in LITON General Purpose Recessed Housings and is specified as “DLV” when ordering.
Please see specification sheets for further details.
Synonymous Terms:
Electronic Low Voltage, ELV, Trailing Edge and Reverse Phase
Benefits
• ELV dimming drivers from Liton are the LED driver most widely tested and approved by dimmer manufacturers
(see list).
• Works better on LEDs than most magnetic low voltage (MLV) drivers.
• Allows smooth dimming down to 5% depending upon the dimmer’s limitations.
Limitations
• ELV wall dimmers can be more expensive than incandescent or magnetic low voltage dimmers.
• Smaller install base could mean replacing incompatible dimmers on retrofit projects.
• ELV drivers should not be used with incandescent dimmers because doing so could cause any of the following
malfunctions: dimmer buzz, lamp flicker, interaction between circuits or radio frequency interference (RFI).
• All ELV drivers and dimmers are 3-wire, requiring a neutral wire. This can result in having to pull additional wire
on remodel projects.
Electronic Low Voltage (ELV) Dimmer Wiring Diagram Examples of ELV dimmers:
(See next page for a more comprehensive list):
3
Hot
Neutral
Black Yellow
ELECTRONIC
LOW VOLTAGE
DIMMER
120V
60Hz
Manufacturer Style Model
Lutron Skylark SELV-300P
Lutron Diva DVELV-300P
Lutron Maestro MAELV-600
Lutron Nova NTELV-600
Lutron Vierti VTELV-600
Leviton Surslide 6615-POW
LiteTouch Inverse Phase 08-2140-01
LiteTouch 8-Channel 6615-POW
DIMMING FACTS
FOR LED PRODUCTS
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
(ELV) Factory Qualified Dimmers for
Under Cabinet “LULED” Series, Track Lighting “LTD8” Series
and Recessed Lighting “LHLD” 4", 5" & 6" Series
Series Model Power
Lyneo® LX
Single Pole
3-Way
Faedra®
Single Pole
Skylark
Single Pole
3-Way
Diva
Single Pole
3-Way
Maestro
Single Pole
Nova
Single Pole
Single Pole
Vierti
Single Pole/Multi Location
Lutron Interfaces
Grafik Eye®
Grafik Eye®
HomeWorks®
RadioRA 2
Commercial Systems
**Low end trim adjustment needed
LXELV-600PL
LXELV-603PL
FAELV-500M
SELV-300P
SELV-303P
DVELV-300P
DVELV-303P
MAELV-600
NELV-450
NTELV-600
VTELV-600
ELVI-1000
PHPM-PA Power Module
HW-RPM-4A**
RRD-6XA**
LP-RPM-4A**
600W
600W
600W
300W
300W
300W
300W
600W
450W
600W
600W
Avg. Price
SELV-300P
SELV-300P
$45 - $55
$45 - $55
$80 - $100
$80 - $100
$110 - $150
$80 - $85
$150 - $200
$180 - $200
$130 - $180
# Units per Dimmer
1 - 13
1 - 11
1 - 7
1 - 7
1 - 7
1 - 7
1 - 3
1 - 10
1 - 14
1 - 14
2
1 unit min.
1 unit min.
4 units min.
1 - 27
Surslide
Single Pole
3-Way
Vizia
Single Pole
3-Way
Acenti
Single Pole
3-Way
Illumatech
Single Pole
3-Way
6615-POW
6615-POW
VZE06-1LZ
VZE06-1LZ
ATEO-1LW
ATEO-1LW
IPE04
IPE04
600W
600W
600W
600W
400W
400W
300W
300W
$20 - $30
$20 - $30
$90 - $150
$120 - $180
$75 - $100
$75 - $100
$40 - $70
$40 - $70
1 - 14
1 - 14
1 - 14
1 - 14
1 - 9
1 - 9
1 - 7
1 - 7
iLux® Universal Dimmer
Low Voltage Dimmer
Universal Dimmer
CLS-EXP-DIMU
CLX-1DELV4
DIN-1DIMU4
600W
600W SELV-300P 1 - 13
Miro
Single Pole DCD267* 600W $35 - $45 1 - 13
08-2140-01 480W
Electronic Dimmer 120V
Electronic Load Dimmer 120V EDIMMOD
ELDS4-DIN 600W
600W SELV-300P 1 unit min.
1 unit min.
VANTAGE
QUALIFIED PARTNER
(Qualified LED Partner)
(Certified Partner)
4
Unison Dimmer Module
Unison Dimmer Module ELV10
D20 0W
154W
120V Inverse Phase
DIMMING FACTS
FOR LED PRODUCTS
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
Magnetic Low Voltage (MLV) Dimming
History
Magnetic Low Voltage (MLV) Dimmers were designed to control Magnetic Low Voltage Transformers used in low voltage
lighting fixtures.
Where Used?
MLV Dimming can be used in LITON Linkaled products and come standard on all LD522 drivers.
Synonymous Terms:
Magnetic Low Voltage, MLV
Benefits
• Liton’s magnetic low voltage (MLV) drivers are specially designed to function with most magnetic low voltage
dimmers.
• Allows smooth dimming down to 10% depending upon the dimmer’s limitations.
• All MLV drivers and dimmers are 2-wire and do not require an additional neutral wire.
• MLV dimmers are less expensive than electronic low voltage dimmers or 0-10V dimmers.
Limitations
• MLV wall dimmers can be more expensive than incandescent dimmers
• MLV drivers should not be used with incandescent dimmers because doing so could cause any of the
following malfunctions: dimmer buzz, lamp flicker, interaction between circuits or radio frequency interference
(RFI).
Magnetic Low Voltage (MLV) Dimmer Wiring Diagram
Examples of MLV dimmers:
(See next page for a more comprehensive list):
Manufacturer Style Model
Lutron Nova NTLV-1000
Lutron Diva DVLV-103P
Lutron Skylark SLV-603P
Lutron Illumatech IPM06-1LZ
5
Hot
Neutral
LD522
Driver Linkaled Tape, Bar or Puck
Black Black
MAGNETIC
LOW VOLTAGE
DIMMER
120V
60Hz
DIMMING FACTS
FOR LED PRODUCTS
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
Factory Tested (MLV) Dimmers for Linkaled Products
Series Model
Ariadni®
Single Pole
3-Way
Vareo®
Single Pole/Multi Location
Nova®
Single Pole
Single Pole / 3-Way
3-Way
4-Way
Ceana®
Single Pole
3-Way
Diva®
3-Way
Single Pole
3-Way
4-Way
Glyder®
Single Pole
Lyneo®
Single Pole
3-Way
Nova T®
Single Pole
Skylark®
Single Pole
3-Way
AYLV-600P AYLV-600P-S AYLV-600P-CSA
AYLV-603P AYLV-600P-S AYLV-603P-CSA
V-600 V-600-S V-1000
V-1000-S VETN-1000 VETS-1000
VETN-1000-S VETS-1000-S VETS-1000-CSA
VETS-R VETS-A-SL VETS-R-S VETS-A-SL-S
VETS-1000-SL VETS-1000-SL-S
NTLV-600 NTLV-600-S NT1PS
NTLV-1000 NTLV-1000--S NT-1PS-S
NTLV-1500 NTLV-1500-S NT-1PS-CSA
NTLV-603P NTLV-603P-S NT-3PS
NTLV-1003P NTLV-1003P-S NT-3PS-S
NTLV-1503P NTLV-1503P-S NT-3PS-CSA
NTLV-2003P NTLV-2003P-S NT-4PS-
NTLV-603P-CSA NTLV-1003P-CSA NT-4PS-S
NTLV-1503P-CSA NT-4PS-CSA
CNLV-600P
CNLV-603P
DVLV-603P DVSCLV-603P DVLV-603P-CSA
DVLV-603P-S DVLV-603PH-S DVSCLV-603P-L
DVLV-103P DVSCLV-103P DVLV-103P-CSA
DVLV-103P-S DVLV-103PH-S DVSCLV-103P-L
DVLV-10P DVSCLV-10P DVLV-10P-CSA
DVLV-10P-S DVLV10PH-S DVSCLV-10P-L
DVLV-600P DVSCLV-600P
SC-1PS SC-1PSNL SC-3PS
SC-3PSNL SC-4PS SC-4PSNL
GLV-600 GLV-600-CSA
LXLV-600PL LXLV-10PL
LXLV-603PL LXLV-103PL
NTLV-600 NTLV-600-277
NTLV-1000 NTLV-1000-277 NTLV-1500
SLV-600P SLV-600P-CSA SLV-600PH-CSA
SLV-603P SLV-603P-CSA SLV-603PH-CSA
IllumaTech®
Single Pole / 3-Way
Single Pole / 3-Way
Mural
Single Pole / 3-Way
Single Pole / 3-Way
SureSlide®
Single Pole / 3-Way
ToggleTouch
Single Pole / 3-Way
Single Pole / 3-Way
Vizia®
Single Pole / 3-Way
IPM06-1LZ IPM06-1LX
IPM10-1LZ
MDM06-1LI MDM06-1LW MDM06-1LA
MDM10-1LI MDM10-1LW MDM10-1LA
6613-PLT 6613-PLI 6613-PLW 6613-PLA
TGM10-1LI
TGM10-1LT TGM10-1LA
VPM06-1LZ
(Qualified LED Partner)
6
DIMMING FACTS
FOR LED PRODUCTS
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
7
DIMMING FACTS
FOR LED PRODUCTS
0-10V Dimming Driver Option
History
0-10V Dimmers have been used in commercial applications for fluorescent lighting and occupancy and daylight sensor
systems for years and are now becoming popular with LED products. One reason this standard is widely established is
that it is defined in the IEC standard number 60929 Annex E, making it acceptable to most engineers.
Where Used?
LITON offers 0-10V drivers in its 5" and 6" General Purpose Recessed Housings, Architectural Recessed Housings, 24V
Linkaled products and are specified as “-D10” when ordering. Please see specification sheets for further details.
Synonymous Terms:
0-10V, Fluorescent Dimming, 5-Wire Dimming.
Benefits
Use existing 0-10V systems in retrofit applications.
Liton’s -D10 LED Driver is compatible with most 0-10V control systems.
Large 0-10V install base in commercial applications due to IEC standards.
Allows smooth dimming down to 5% depending upon the dimmer’s limitations.
Compatible with many daylight harvesting controls.
Limitations
Some manufacturers do not follow the IES standard. This leads to LED drivers and lamps that claim 0-10V
compatibility but drop out or pop on, or dim backwards with the lowest output at the top and the highest output at
the bottom.
The control signal is a small analog voltage and long wire runs can cause a signal level drop that can produce
different light levels from different drivers on the same control circuit.
0-10V Dimmer Wiring Diagram
Example 1:
Manufacturer Style
Leviton IP710-DLX
Lutron NTFTV-WH*
*requires separate power pack, not supplied
Lightolier V2000FAMU
Synergy Mark VII ISD 120/277 WH-M10
-D10: 0-10V Fluorescent Dimming
1Usually dimming control color,
may be other color
Electronic
LED Driver
Negative (Gray)1
Data - Negative (Gray)1
Line (Black)
LEVITON: IP710-DL
or other
Line (Black)
Neutral (White)
Neutral (White)
Input Line Red
Insulating
Label
Positive (Violet)1
Data + Positive (Violet)1
Line (Black)1
Line (Red)
Ground (Green)
To LED
+
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
More Examples of 0-10V Dimming Systems:
Manufacturer Style
Douglas Lighting ALC3-BCM
Douglas Lighting WPN-5821/5822/5721
Douglas Lighting WWS-1301/1302
Manufacturer Style
Hunt Dimming PS-010-120V & PS-010-3W-120V
Hunt Dimming PS-010-277V & PS-0101-3W-277V
Hunt Dimming PS-LED-010-120V, PS-LED-010-3W-120V
Hunt Dimming PS-LED-010-277V, PS-LED-010-3W-277V
Manufacturer Style
Leviton a-2000
Leviton IP710
Leviton Renior II (w/ 0-10V Setting)
Manufacturer Style
Lehigh Electrical Co., Inc. Collage Impress Touch Master
Lehigh Electrical Co., Inc. CT500 LCD Touch
Lehigh Electrical Co., Inc. DX2, DX2 277
Lehigh Electrical Co., Inc. Single Set
8
DIMMING FACTS
FOR LED PRODUCTS
Manufacturer Style
Lutron DVTV, DVSCTV
Lutron NFTV
Lutron NTFTV
Manufacturer Style
Wattstopper, Inc. ADF-120277
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
Lutron Hi-Lume Dimming Option
History
Lutron originally developed its Hi-Lume 1% Dimming ballast for use with fluorescent and compact fluorescent dimmer
controls. It is a 3-wire system that has a separate line voltage wire that carries the phase control signal separate from the
power wires. Hi-Lume drivers dim down to 1% of initial lumens, are more precise and more immune to electrical noise.
Where Used?
LITON offers Hi-Lume drivers in many of its General Purpose, Mini-Arc and Architectural LED products and are specified
as “-DHL” when ordering.
Synonymous Terms:
Hi-Lume, 3-Wire
Benefits
• Allows smooth, continuous dimming down to 1% of initial lumens depending on dimming control limitations.
• Lutron’s Hi-Lume LED driver is compatible with more Lutron dimmers than any other brand and also compatible
with their EcoSystem control system.
• Backed by Lutron’s 5-year Limited Warranty.
Limitations
• Compatible Lutron wall dimmers can be more expensive than electronic low voltage, incandescent or magnetic
low voltage dimmers.
• All Lutron Hi-Lume drivers and compatible dimmers are 3-wire, requiring a neutral wire. This could necessitate
pulling additional wire.
• The “-DHL” option should not be used with incandescent dimmers because doing so could cause any of the
following malfunctions: dimmer buzz, lamp flicker, interaction between circuits or radio frequency interference
(RFI).
-DHL Wiring Diagram
Partial list of factory tested, compatible dimmers:
(See next page for the Lutron Compatibility Report Card)
Manufacturer Style Model
Lutron NovaT NTF-10-277
Lutron Skylark SF-12P-277
Lutron Vierti VTF6A
-DHL: Lutron 3-Wire Fluorescent Dimming (120V)
9
1Usually dimming control color,
may be other color
3-Wire
Electronic
120V/277V AC
Dimming Ballast/
LED Driver
Dimming Line
(Orange)1
Dimming Line
(Yellow)
Line (Red)
Ground “Green”
Line (Black)1
Line (Black)Line (Black)
Input Line
120V/277V AC
Neutral (White)
Neutral (White)
Neutral (White) To LED
+
LUTRON
3-Wire Dimmer
DIMMING FACTS
FOR LED PRODUCTS
A DIVISION OF EEMA LIGHTING GROUP • 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA • PH: 323.904.0200 (1 800 515 4880) FAX: 323.904.0201 (1 800 972 4880)
* Fixtures per control assumes a 40W fixture. Number of fixtures may be higher if wattages is less than 40W and may be lower if ganged. See control specification submittal sheet for details.
** For use with 3-wire controls or Commercial Systems, RadioRA Systems, or Home Systems applications.
NovaT®
Skylark®
Ariadni®
Maestro®
Vierti®
Maestro Wireless®
RadioTouch®
Spacer System®
Lyneo® Lx
RadioRA® 2
HomeWorks® QS
Interfaces**
PowPak™ dimming
module with EcoSystem
Diva®
Nova®
Vareo®
Product Family Measured light
output range
Part Number
120V 277V
NTF-10
NTF-103P
NF-10
NF103P
VF10
SF-10P
SF-103P
DVF-103P
DVSCF-103P
AYF-103P
VTF-6A
MAF-6AM
MSCF-6AM
MRF2-F6AN-DV
RTA-RX-F
SPSF-6A
SPSF-6AM
LXF-103PL
RRD-F6AN-DV
HQRD-F6AN-DV
PHPM-3F
GRX-FDBI-16A
NTF-10-277
NTF-103P-277
NF-10-277
NF130P-277
SF-12P-277
SF-12P-277-3
DVF-103P-277
DVSCF-103P-277
AYF-103P-277
MAF-6AM-277
MSCF-6AM-277
SPSF-6A-277
SPSF-6AM-277
LXF-103PL-277
PHPM-3F-DV
Fixtures per Control*
120V 277V
1 - 41
1 - 20
1 - 41
1 - 20
1 - 20
1 - 20
1 - 20
1 - 20
1 - 20
1 - 20
1 - 15
1 - 15
1 - 15
1 - 15
1 - 41
1 - 15
1 - 15
1 - 20
1 - 15
1 - 15
1 - 41
1 - 41
1 - 44
1 - 33
1 - 44
1 - 33
-
1 - 33
1 - 33
1 - 33
1 - 33
1 - 44
1 - 33
1 - 33
1 - 33
1 - 33
1 - 88
1 - 33
1 - 33
1 - 33
1 - 33
1 - 33
1 - 88
1 - 88
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
RMJ-ECO32-DV-B
QSN-1ECO-S, QSN-2ECO-S
Quantum®
QSG-_P120
32 per EcoSystem link
63 per EcoSystem link
64 per EcoSystem link
100% - 1%
100% - 1%
100% - 1%
Various 64 per EcoSystem link 100% - 1%
10
PowPak™ dimming
module with EcoSystem
PowPak™ dimming
module with EcoSystem
Qualified Hi-Lume® Dimmers
For fixtures using the Lutron Hi-Lume® A-Series LED Driver
DIMMING FACTS
FOR LED PRODUCTS
© 2012 LITON LIGHTING • A DIVISION OF EEMA LIGHTING GROUP
DIMMING FACTS
FOR LED PRODUCTS
Page 1 of 12 - Cover  68684-Catalog
Page 2 of 12 - Cover  68684-Catalog
Page 3 of 12 - Cover  68684-Catalog
Page 4 of 12 - Cover  68684-Catalog
Page 5 of 12 - Cover  68684-Catalog
Page 6 of 12 - Cover  68684-Catalog
Page 7 of 12 - Cover  68684-Catalog
Page 8 of 12 - Cover  68684-Catalog
Page 9 of 12 - Cover  68684-Catalog
Page 10 of 12 - Cover  68684-Catalog
Page 11 of 12 - Cover  68684-Catalog
Page 12 of 12 - Cover  68684-Catalog

Navigation menu