Kenmore Front Load Washer Wiring Sheet 417.24182301

: Pdf Kenmore Front Load Washer Wiring Sheet 417.24182301 Kenmore Front Load Washer Wiring Sheet 417.24182301 Kenmore

Open the PDF directly: View PDF .
Page Count: 4

WIRING DIAGRAM

If grounding wires, screws or clips used to complete a path to ground are removed

for service, they must be returned to their original position and properly fastened.

Certain internal parts are intentionally NOT grounded and may present a risk of

electric shock only during servicing. Do not contact the following parts while the

appliance is energized: pump, drive motor and electronic control boards.

IMPORTANT

This information is intended for use by technicians possessing

adequate background of electrical, electronic and mechanical

experience. Any attempt to repair a major appliance may result in

personal injury and property damage. The manufacturer or seller

cannot be responsible for the interpretation of this information, nor

can it assume any liability in connection with its use.

IMPORTANT SAFETY NOTICE

TECH SHEET - RETAIN FOR SERVICE TECHNICIAN

Disconnect from Electrical Supply Before Servicing Washer.

PART NO. 134578300

Motor Will Not Run

Timer/off

Door/open

SWITCH

POSITION CIRCUIT

WATER TEMP SWITCH

COLD

X

X

X

WARM

X

X

X

DELICATE X

HOT

1 - 31 - 5 2 - 6W/R

C10.10 (D)

C10.9 (E)

C10.6 (C)

C10.1 (B)

C10.2 (A)

C10.5 (TM)

C10.8 (F)

TIMER

MOTOR

C6.5 (AC)

C6.6 (AC)

C6.2 (P2)

C6.3 (P3)

C6.1 (P1)

C6.4

C10.3 (T2)

C10.4 (T1)

TIMER

DIRECT

2

1

BLU/

WHT

WHT/RED

RED/BLK

TAN/WHT

YEL/WHT

YELLOW

AQUA

AQUA

YELLOW

JUMPER

WIRE

BLK/RED

TAN/BLK

ORG/WHT

BLUE

PINK/BLK

WHT/RED

BROWN

RED

YEL/BLK

B

2B

4

2

MOTOR CONTROL

T

T12 B

T

0T 0C

BLEACH SOFTENER

PINK

BLEACH

SOFTENER

MS

DISPENSER

VALVES

WATER LEVEL

PRESSURE

SWITCH

2.2 4.3

DOOR

LOCK

SWITCH

DISPENSER

DRAWER

REED SWITCH

7B5B3B1B

6T

7C5C3C1C

6C

1

23

MPUMP

MOTOR

TB

14

#2

#6

WAX

MOTOR

PTC

+t

2

1

ORG/BLK

GREEN

65324 1

TACHO-

GENERATOR

T

MOTOR

WINDING

1. CHECK FOR POWER:

Advance the timer knob to the drain

increment. If the drain pump does not run,

check household safety circuit. If the drain

pump runs go to step 2.

2. CHECK FOR MOTOR MOVEMENT:

Turn the water off to the washer. Remove

electrical power from the washer and

remove the back panel. Remove the motor

drive belt. Reconnect electrical power and

set the timer to the start of the Regular wash

cycle and pull the knob out. If motor does

not rotate, check for a poor connection in the

timer line switch, coin box circuit, or door lock

switch. If good, and motor does not run go to

Step 3.

3. MEASURE VOLTAGES:

Remove the six pin plug from the speed

control unit. Measure the voltage between

pins 5 and 6 on the harness. If the meter

reads 0 check the connection in the timer

line switch or door lock. If the meter

reads 120 Vac go to step 4.

4. Set the timer to the Heavy Wash position of

the Regular wash cycle. Remove the ten pin

plug from the speed control unit. Measure

the voltage between pins 1, 2, 6 and 10 of

the ten pin plug to pin 5 of the 6 pin plug on

the harness. The voltage at pins 2, 6, and

10 should read 120 Vac and 0 Vac at pin 1.

If not, check timer contacts 1C to 1B, 5C to

5B, and 7C to 7B for closed contacts, and

3C to 3B for open contacts. If the voltage

readings are correct, go to step 5.

5. MEASURE RESISTANCES:

Check the fuse on the speed control board.

If the fuse is open, replace the speed control

board. If good, go to step 6.

6. Remove the 6 pin plug from the speed

control unit. Measure the resistance

between pins 1 and 2, 2 and 3, and 3 and 1

of the speed control unit. If the meter reads

other than 3 Meg ohms ± 10%, replace the

speed control board.

7. Remove electrical power from the washer.

With an ohmmeter check the resistance

between pins 1 and 2, 2 and 3, and 3 and 1

of the six pin plug on the harness. If the

meter reads other than 2.6 ohms ± 7%,

replace the motor.

Quick Facts

• The timer motor will not run continuously.

The speed control unit controls the timer

motor and advances the timer when needed.

•In some tumble modes, the tub may not

tumble for the first 16 to 20 seconds after

start-up.

• Extremely low water pressure may cause

tub rotation to stop until WLC satisfied.

GRN

CABINET COIN METER

BLU/WHT

WHT WHT

WHT

#1

#5

#7

N

GND

#3

Speed

Control

6

1

Speed

Control

6

1

Speed

Control

6

1

510

16

RINSE

WATER

WASH

WATER

WASH

WATER

35

1

C

8

YELLOW

BLUE

PURPLE

GRAY

TEMP SWITCH

HOT COLD

WATER

VALVES

T

B10

DOOR

LOCK

COIL

2

1

4.4

2.1

BLK/WHT

#4

TEMPERATURE

SWITCH

AQUA

6

2

4F

2

6M

5F

3F

1

SLIDE COIN METER

JUMPER POSITION

FOR MANUAL

WASHERS

4M

2

6F

5M

3M

1

M

4M

2

6

5M

3

1

DROP COIN METER

4M

2

6F

5M

3M

1

TIMER LINE

SWITCH

START

SWITCH

BLK

BLK

BLK/WHT

L1

DOOR LAMP

BOLD LINES = INTERNAL TIMER CIRCUIT

DASHED LINES = NOT ON ALL MODELS

TIMER

JUMPER

WIRE

COIN METER

SWITCH

TIMER

TIMER

TIMER

TIMER

TIMER

TIMER

DOOR LOCK

DOOR LOCK

DOOR LOCK

DOOR LOCK

DOOR LOCK

PUSH-TO-START

SWITCH

PUSH-TO-START

SWITCH

TIMER

TIMER

TIMER

TIMER

TIMER

TEMP

SWITCH

TIMER

TIMER

DOOR LOCK

COIL

DOOR LOCK

COIL

DOOR LOCK

COIL

HOT

WATER

SOLENOID

DOOR LOCK SOLENOID WON'T ENERGIZE

DOOR LOCK SOLENOID WON'T ENERGIZE (Timer In OFF Position - Non-Metered Machine)

DOOR LOCK SOLENOID WON'T ENERGIZE (Timer In OFF Position - Metered Machine)

DOOR LAMP WON'T LIGHT

IF NO HOT, WARM, OR COLD WATER DURING WASH FILL

L1 N

OT

OT

OT

OT

OT

OT

OT

4.3

4.3

4.3

4.3

4.3

8T

8T

14C

14C

1

110B

10T

DOOR LAMP

WATER LEVEL

SWITCH

OC

OC

OC

0C

OC

OC

OC

2.2

2.2

2.2

2.2

2.2

8C

2C

2C

4C

4C

14B

14T

2.1

2.1

2.1

4.4

4.4

4.4

12C

12C

3

510C

10C

COLD

WATER

SOLENOID

COLD

WATER

SOLENOID

TIMER

MOTOR

PUMP

MOTOR

DUMP VALVE

MOTOR

IF NO COLD WATER DURING RINSE FILL

IF TIMER WON'T ADVANCE

IF WATER PUMP DOES NOT WORK (Models With Pump)

IF WATER DUMP VALVE DOES NOT WORK (Models With Dump Valve)

TIMER

12C

MS

This information is intended for use by persons having electrical and mechanical training and a level of

knowledge of these subjects generally considered acceptable in the appliance repair trade. The seller or

manufacturer cannot be responsible, nor assume any liability, for injury or damage of any kind arising from

the use of this data.

WARNING

!

NOTE: BOLD LINES INDICATE INTERNAL TIMER CIRCUITS.

Reconnect all grounding devices, all parts of this appliance capable of conducting electrical current are

grounded. If grounding wires, screws, straps, clips, nuts or washers used to complete a path to ground

are removed for service, they must be returned to their original position and properly fastened.

IMPORTANT

DIAGNOSTIC STRIP CIRCUITS

M

REED

SWITCH

REED

SWITCH

REED

SWITCH

2

3

1

1

1

1

2

2

2

2

3

1

PART NO. 134578300

TIMER

WATER LEVEL

SWITCH

SPEED

CONTROL

C10.5 C6.5

TIMER

6C 6T

MOTOR

(PHASE 1) 3

(PHASE 2) 2

(PHASE 3) 1

(TACH) 5

(TACH) 6

(GND) 4

IF NO MOTOR ROTATION DURING FILL OR AGITATION

IF NO MOTOR ROTATION DURING SPIN

L1 N

SPEED

CONTROL

C6.6

(AC)

C6.6

(AC)

C6.5

(AC)

C6.5

(AC)

MOTOR

C6.1 (P1)

C6.2 (P2)

C6.3 (P3)

C10.3 (T2)

C10.4 (T1)

C6.4 (GND)

(PHASE 1) 3

(PHASE 2) 2

(PHASE 3) 1

(TACH) 5

(TACH) 6

(GND) 4

SPEED

CONTROL

C10.2 (A)

C10.1 (B)

C10.6 (C)

C10.10 (D)

TIMER

12C 12T

TIMER

TIMER

TIMER

TIMER

1C

3C

5C

7C

1B

3B

5B

7B

TIMER CONTACTS 1, 3, 5 AND 7:

REFER TO TIMER CHART FOR THE

MOTOR CONTROL CODE AND

MACHINE FUNCTION.

C10.2 (A)

C10.1 (B)

C10.6 (C)

C10.10 (D)

WATER LEVEL

SWITCH

2

3

1

TIMER

0T 0C

DOOR

LOCK

TIMER

YELLOW

JUMPER WIRE

(OPTIONAL)

YELLOW

JUMPER WIRE

(OPTIONAL)

2.2 4.3 12T

TIMER

TIMER

TIMER

TIMER

1C

3C

5C

7C

1B

3B

5B

7B

4C

TIMERTIMER

2C 4T

2

3

1

TIMER

0T 0C

DOOR

LOCK

2.2 4.3

WATER LEVEL

SWITCH

C10.8 (F)

C10.9 (E)

C6.1 (P1)

C6.2 (P2)

C6.3 (P3)

C10.3 (T2)

C10.4 (T1)

C6.4 (GND)

26

TEMP

SWITCH