TECHNOTE/TM8000/TN 873_TM8100_Control_Head_Attach_and_Detach_Procedure TN 873 TM8100 Control Head Attach And Detach Procedure
User Manual: Pdf TECHNOTE/TM8000/TN-873_TM8100_Control_Head_Attach_and_Detach_Procedure
Open the PDF directly: View PDF .
Page Count: 3
Download | |
Open PDF In Browser | View PDF |
Technical Note TN-873 TM8100 Control Head Attach and Detach Procedure 10 June 2004 Applicability This Technical Note applies to the TM8100 family of mobile radios, including the TM8105, TM8110 and TM8115. 1. Control Head Removal 1. Disconnect the transceiver from any test equipment or power supply. 2. Note the two points where the control head should be levered off the radio body. As shown in Figure 3.1 below, these points are indicated by a dot-dash-dot marks on the underside of the radio body. The lever point is between the rubber seal and the front panel of the control head. 3. Using each of the lever points, insert the blade of a medium-sized (about 5mm) flat-bladed screwdriver and lever off the control head with an up-and-forward motion. 4. After detaching the control head, disconnect the control-head loom at the connector on the radio body. Refer to Figure 3.2 next page. TN-873 Page 1 of 3 Tait Electronics Limited PO Box 1645, Christchurch, New Zealand support.taitworld.com 10 June 2004 Telephone: +64–3–358–3399 Facsimile: +64–3–358–3903 2. Control Head Attachment It is highly recommended the body seal be replaced when replacing the control head to preserve the integrity of the radio’s IP54 rating. There is a kit of 10x body seals available as part code TMAA22-07 - Spares Kit Body Seals. 1. Reconnect the control-head loom to the connector on the radio body. See Figure 3.2 above. 2. Align the control head with the front of the radio body. Ensure the control-head loom folds properly into the space between the control head and the radio body. 3. Press the control head against the radio body until it clips into position. The most effective method noted has been to position the top of the control head over it’s respective locating lugs and roll the head flat to clip the bottom into position. Compliance Issues None. CSO Instruction Inform all Technical staff and accredited dealers of the procedure detailed here. TN-873 Page 2 of 3 Tait Electronics Limited PO Box 1645, Christchurch, New Zealand support.taitworld.com 10 June 2004 Telephone: +64–3–358–3399 Facsimile: +64–3–358–3903 3. Issuing Authority Name and Position of Issuing Officer Graham Brenchley Technical Support Engineer. Confidentiality Confidential – This message or document contains proprietary information intended only for the person(s) or organisation(s) to whom it is addressed. All Recipients are legally obliged to not disclose Tait technological or business information to any persons or organisations without the written permission of Tait. Distribution Level Public Document History Original Release TN-873 Page 3 of 3 Tait Electronics Limited PO Box 1645, Christchurch, New Zealand support.taitworld.com 4 June 2004 GCB 10 June 2004 Telephone: +64–3–358–3399 Facsimile: +64–3–358–3903
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Modify Date : 2004:06:10 13:43:10+12:00 Create Date : 2004:06:10 13:43:00+12:00 Page Count : 3 Creation Date : 2004:06:10 01:43:00Z Mod Date : 2004:06:10 01:43:00Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : m m Metadata Date : 2004:06:10 01:43:00Z Creator : m m Page Mode : UseNoneEXIF Metadata provided by EXIF.tools