Pioneer K078 Pedaling Monitor Sensor User Manual Short term Confidential

Pioneer Corporation Pedaling Monitor Sensor Short term Confidential

Contents

(Short term Confidential)User Manual

ENDEFRNEITESENDEFRNLITESPlease read the Important Information for the User in the product box for product warnings and other important safety information.User's ManualPedaling Monitor SensorSGY-PM910H
2ENIntroductionTable of ContentsIntroductionFeatures ................................................................................................................... 3Manuals ...................................................................................................................................3Compatibility ............................................................................................................ 4Getting StartedProduct Conguration .............................................................................................. 5Accessories.............................................................................................................................5Installing and Removing the Batteries/Switching Modes ........................................ 7Pairing /CalibrationPairing with the Cyclocomputer ..............................................................................10Calibrating the Sensors ..........................................................................................12Getting Ready .......................................................................................................................12Calibrating the Zero Point .....................................................................................................12Checking the Zero Point .......................................................................................................13Calibrating in Power Meter Mode .........................................................................................13Specifications and supportTroubleshooting ......................................................................................................14Care, Maintenance, and Storage ...........................................................................16Specications .........................................................................................................17This product is ANT+™ certied.Visit http://www.thisisant.com/directory/ for a list of compatible products and apps.Introduction
3ENIntroductionFeaturesThis product is a sensor system that analyzes the pedaling of a bicycle in real time. It calculates the direction and intensity of the force acting on the pedals and calculates pedaling efciency.Description of componentsStrain gauge unit: • Detects the strain on the crank and calculates the direction and intensity of the force on the crank.Magnet: • Used to detect the angle of rotation.Transmitters: • Send information from the strain gauge unit and the magnet to the Cyclocomputer.Switching modesThe switch in the right transmitter changes the system to the following modes.Pedaling mode• : Used in combination with the Cyclocomputer SGX-CA500/CA900. This mode calculates pedaling efciency and maximizes the functionality of the product.Power meter mode• : Used with a Cyclocomputer that supports ANT+™.ManualsThe product’s manuals consist of this User’s Manual, an Installation Manual, and Important Information for the User.User’s Manual:• Explains how to pair the product with the Cyclocomputer and calibrate the sensors.Installation Manual:• [For American Users] http://www.pioneerelectronics.com[For Canadian Users] http://www.pioneerelectronics.ca[For European Users] http://www.pioneer.euExplains details about handling methods. The product installation methods (for dealers) are also described as references.Important Information for the User:• Important Information for the User provides detailed information related to safety.
4ENIntroductionCompatibilityCrank setsThe product is compatible with the following crank sets.Crank sets RemarksSHIMANO FC-9000 Crank lengths of 165, 167.5, 170, 172.5, 175 mm, crank set • of 50-34T, 52-36T, 52-38T, 53-39T, 54-42T, 55-42T are compatible. *FC-6800 Crank lengths of 165, 170, 172.5, 175 mm, crank set of 50-• 34T, 52-36T, 53-39T are compatible. ** Descriptions in this manual are for a 170 mm crank set.This product is designed to be used for recreational cycling and cycle training applications only and is not designed to withstand racing conditions.Additionally, this product is designed to be used while cycling on paved roads only. Any damage or malfunction arising from use in racing or riding on dirt roads, cobblestone or any other unpaved roads will not be covered by the manufacturer’s limited warranty.Installing and calibrating the product requires specialized techniques and tools. Ask the shop where you bought the product to install and calibrate it.Getting Started
5ENGetting StartedProduct CongurationAccessoriesThis product contains the following parts.Pedaling monitor sensor (right side) Right transmitter Junction cable Strain gauge unit Junction boxPedaling monitor sensor part (right side) x 1For FC-9000For FC-6800Chain ring adapter x 1Strain gauge unit cover (right side) x 2Getting Started
6ENGetting StartedProduct CongurationPedaling monitor sensor (left side) Left transmitter Strain gauge unitPedaling monitor sensor part (left side) x 1MagnetMagnet x 2AccessoriesPhillips-head screws x 10User's Manual (this document)Warranty CardImportant Information for the UserBatteries (CR2032) x 2
7ENGetting StartedInstalling and Removing the Batteries/Switching ModesYou must install the batteries before using the product.The product can be used as the ANT+ Power meter with the cyclocomputers of other • companies (power meter mode).To use the product in power meter mode, insert the battery in the left-side part rst, and then the right-side part.1. Loosen the screws on the transmitter and remove its cover.Use a hex wrench (2 mm) to loosen the screw and remove the cover.Be careful not to lose the removed • screw.Right transmitter (screws: 3 x)• Left transmitter (Loosen/tighten • with coin)2. Remove the old battery.Right transmitter•
8ENGetting StartedInstalling and Removing the Batteries/Switching ModesLeft transmitter• 3. Install the new battery (CR2032).Do not use batteries other than • CR2032.4. Check the LED display.Check the following LEDs to make sure that they are working properly.Pedaling mode• :When the batteries are installed, the LEDs light green for 10 seconds.Power meter mode• :When the batteries are installed, the left and right transmitters start pairing. When pairing is nished, the LEDs on the left and right transmitters light green for 10 seconds.If the LEDs do not light, or only one • side lights, install the batteries again. If the LEDs still do not light, the battery may be almost empty. Replace the battery with a new one.5. Start the sensors.Rotate the bicycle’s crank set one rotation to start the sensors.6. Check the sensor modes.Pushing the push switch in the right transmitter, the LEDs light as follows depending on the actual sensor mode.Pedaling mode• :The LEDs light green for 5 seconds.Power meter mode• :The LEDs light orange for 5 seconds. Push switch LEDMake sure that the left and right • sensors light properly.
9ENGetting StartedInstalling and Removing the Batteries/Switching Modes7. Switch the sensor mode.Change the sensor mode by using the push switch in the right transmitter while the batteries are removed.While in pedaling mode• :The sensors restart in power meter mode and the LEDs light orange for 5 seconds.While in power meter mode• :The sensors restart in pedaling mode and the LEDs light green for 5 seconds.For use with Pioneer’s SGX-CA500/• CA900, set the sensor mode to pedaling mode.For use with other cyclocomputer brands, set the sensor mode to power meter mode.If the left transmitter is not found, the • LEDs blink red 5 times.If the LEDs on the left and right • transmitters do not light the same color, green or orange, another left transmitter may be connected. In this case, check that both side transmitters light properly in a location away from any other left transmitter, and then switch the sensor modes. 8. Install the cover and tighten the screws to x it in place.Use a tool that can measure the torque to tighten the screws.Tightening torque: 18 cN·m•
10ENPairing / CalibrationPairing with the CyclocomputerThis section describes how to pair the installed SGX-PM900 pedaling monitor sensors on your bicycle to the SGX-CA500/CA900 Cyclocomputer.This pairing procedure may be different if you are using a cyclocomputer other ●than the Pioneer SGX-CA500/CA900. Please refer to your cyclocomputer’s owner manual for sensor pairing.1. Check the sensor modes.Check that the right transmitter and the left transmitter are in "Pedaling mode."See page 8 to switch the modes.• 2. Tap the [Sensors] icon in the home screen of the SGX-CA500/CA900.The sensor list screen opens.3. Rotate the bicycle’s crank set three rotations to start the transmitter.Pair with the Cyclocomputer within • 5 minutes after the transmitters are activated.After the transmitters are activated, it • may take more than 1 minute to pair with the Cyclocomputer.4. Tap [Connect New] in the sensor list screen of the SGX-CA500/CA900.The sensor connection menu opens.5. Tap [Device Type] and then [Pedaling Monitor R].For the left transmitter, tap [Pedaling • Monitor L].If multiple sensors are activated, • bring the main unit closer to the sensor, or specify the device number to pair the sensor you want to pair.Refer to the User's Guide of the Cyclocomputer SGX-CA500/CA900 regarding how to specify a device number to pair a sensor.Pairing / Calibration
11ENPairing / CalibrationPairing with the Cyclocomputer6. Tap [Search].The search for the sensor starts.A [Searching. Please wait.] message appears.7. Check the information about the sensor.Information about the sensors appears when the sensors are found.Check the following items.[Device Number]• Make sure that the device number is the same as the device number of the transmitter.[Error Rate]• Make sure that “OK” is displayed.The device numbers are printed on • the right junction box and on the side of the left sensor. Refer to the Installation Manual for details.If the numbers that are displayed on • [Device Number] are different from the transmitter device numbers, specify the device numbers to pair with the sensor. Refer to the User’s Guide of the Cyclocomputer SGX-CA500/CA900 regarding how to specify a device number to pair a sensor.If “NG” is displayed in the [Error • Rate] area, the information from the sensor is not being received correctly because transmission conditions are bad. Make sure that the sensor you are pairing is activated, then bring the SGX-CA500/CA900 closer to the sensor and perform the pairing operation again.You may not pair with the sensor • due to the inuence of the 2.4 GHz frequency band. If “NG” is displayed even if the SGX-CA500/CA900 is moved closer to the sensor and paired with it, try again someplace where there is no interference from microwaves, radio waves, or wireless equipment.Pairing of the right transmitter is completed. Then, pair the left transmitter.
12ENPairing / CalibrationCalibrating the SensorsThis section describes how to use the Cyclocomputer SGX-CA500/CA900 to calibrate the zero point of the pedaling monitor sensor that is installed on the bicycle.The right-side pedaling monitor sensor is used as an example in this description. The • procedure to calibrate the left side is the same as for the right side.Getting Ready1. Stop the bicycle on a at safe place.Calibrating the Zero Point1. Position the crank arm so it is perpendicular to the ground.2. Tap the [Sensors] icon in the home screen of the SGX-CA500/CA900.The sensor list screen opens.3. Tap [Pedaling Monitor R] and then [Calibration (Zero)].4. Tap [Start Calibration].The calibration starts.If the calibration is successful, “Success” appears in the [Result] eld.If “Failure” is displayed, the sensor may be calibrated in an unstable condition causing the crank to be moving during the calibration. Calibrate again with the crank stopped.This product has a correction • function for the zero point uctuation caused by varying temperatures. The accuracy of this function improves when the sensor is calibrated in different temperatures.This function cannot measure correctly if you calibrate or check the sensor before it is acclimated to the outside temperature.
13ENPairing / CalibrationCalibrating the SensorsChecking the Zero Point1. Position the crank arm so it is perpendicular to the ground.2. Tap [Pedaling Monitor R] in the sensor list screen of the SGX-CA500/CA900.3. Conrm the value in [Force Preview].Make sure that the [Tangential Direction Force] and [Radial Direction Force] values are as shown here.Tangential Direction Force: 0 ± 3 N• Radial Direction Force: 0 ± 3 N• Calibration of the right side is nished. Calibrate the left side in the same way.Calibrating in Power Meter ModeWhen calibrating the sensors in power meter mode, position the crank arm so it is perpendicular to the ground, do the procedure to the left and right sides together. Refer to the User’s Manual of the Cyclocomputer you are using for details.
14ENSpecications and supportTroubleshootingRefer to the following suggestions if you have any problems installing or using the product.If you cannot nd what you want to know here, ask the shop where you bought the product.I cannot pair with the Cyclocomputer in the power meter mode or pedaling mode. ■Cause SolutionThe battery is almost empty. If the LEDs do not light when you install the battery, the battery is almost empty. Replace the battery with a new one.(+) or (-) side of the battery is installed in the opposite side.Install the battery in the proper side (see page 7).Pedaling monitor sensor mode is wrong.Change the mode and pair with the Cyclocomputer (see page 8).There are other wireless equipment or microwave ovens near by.Separate other wireless equipment or microwave ovens. Move the sensor closer to the Cyclocomputer and pair them.Another sensor is paired with the Cyclocomputer.Insert the battery in the left-side part rst, and then the right-side part, and check the sensor mode by pushing the push switch. If the left and right LEDs do not light orange, push and hold the push switch to switch to power meter mode.Ask the shop where you bought the product for details.I cannot pair with the Cyclocomputer in the power meter mode. ■Cause SolutionPairing between right and left sensors fails.Insert the battery in the left-side part rst, and then the right-side part, and check the sensor mode by pushing the push switch. If the left and right LEDs do not light orange, push and hold the push switch to switch to power meter mode.Specications and support
15ENSpecications and supportTroubleshootingZero point calibration fails. ■Cause SolutionThe crank is subjected to external force or moving.Calibrate the sensor in still condition (see page 12).The Cyclocomputer display is not displaying normally while I am riding. ■Cause SolutionZero point calibration fails. Calibrate the zero point (see page 12).There is a rattling noise when I am riding. ■Cause SolutionScrews used to install the sensor are loose.Retighten the screws.The magnet is rubbing while I am riding. ■Cause SolutionForeign objects are attached to the magnet and rub against the transmitter or the junction box.Clean the transmitter, junction box, and magnet.
16ENSpecications and supportCare, Maintenance, and StorageUse a soft dry cloth or a cloth that has been dampened and wrung out to wipe • dirt from the left and right transmitters, the right strain gauge unit cover, the magnet, and other accessories.Do not use benzene, paint thinner, or other volatile chemicals, cleansers, or • chemically treated cloths. Doing so could damage the product or cause the paint to peel off.If you are not going to use the product for a long period of time, remove the • batteries.
17ENSpecications and supportSpecicationsWeight: 73 gDimensions: Pedaling monitor sensor (right side):Right transmitter:• 60.7 mm(W) × 46.9 mm(H) × 21.6 mm(D)Junction box, Strain gauge unit cover:• 63.3 mm(W) × 47.2 mm(H) × 9.9mm(D) Pedaling monitor sensor (left side):99.4 mm(W) × 48.2 mm(H) × 14.6 mm(D) Magnet:φ57.0 mm × 3.5 mmWater resistant: This device has a water resistance rating of IPX-6/IPX-7.Communications method (sensors): ANT+ wirelessBattery: CR2032Battery operating time: Approximately 200 hours (at moderate temperature)Operation temperature: -10 to 50°CAccessories: Magnet, Chain ring adapter, Batteries (CR2032), Cable ties, Phillips-head screws,User’s Manual, Important Information for the User, Warranty CardThe battery operating time may decrease depending on the usage condition. • ANT+ is a Wireless Personal Network protocol with very low power • requirements using 2.4GHz frequency band.For more information, visit http://www.thisisant.com/Specications and design are subject to change without notice.• Illustrations used in this manual may be different from actual appearance.•
©2012 PIONEER CORPORATION.All rights reserved.<Z-912-021-11> EUhttp://www.pioneerelectronics.comhttp://www.pioneerelectronics.cahttp://www.pioneer.euVisit www.pioneer.eu to register your product.Visitez www.pioneer.eu pour enregistrer votre appareil.Si prega di visitare il sito www.pioneer.eu per registrate il prodotto.Visite www.pioneer.eu para registrar su producto.Zum Registrieren Ihres Produktes besuchen Sie bitte www.pioneer.eu.Bezoek www.pioneer.eu om uw product te registreren.PIONEER CORPORATION1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, JAPANPIONEER ELECTRONICS (USA) INC.P.O. Box 1540, Long Beach, California, 90801-1540, U.S.A.TEL: (800) 421-1404PIONEER ELECTRONICS OF CANADA INC.340 Ferrier Street, Unit 2, Markham, Ontario, L3R 2Z5, CanadaTEL: 1-877-283-5901TEL: 905-479-4411PIONEER EUROPE NVHaven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/BelgiqueTEL: +32 (0)3 570 05 11

Navigation menu