Procomp Informatics PW8610IM 802.11 b/g Wireless LAN Cardbus User Manual

Download:
Mirror Download [FCC.gov]
Document ID	417948
Application ID	kmaXBXDOKLvjnkqrDr6CPg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.69kB (283613 bits)
Date Submitted	2004-04-27 00:00:00
Date Available	2004-04-27 00:00:00
Creation Date	2004-04-14 10:11:32
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2004-04-14 10:11:32
Document Title	Microsoft Word - User's Manual with WArning Statement.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	TingLin

Procomp Informatics Ltd.
User Guide
for
Procomp WLAN Solution
IEEE 802.11b/g Wireless Network Adapter
Preface
This user's guide provides the necessary information for first-time users to successfully install
the Procomp network driver interface specification (NDIS) driver, for the purpose of
evaluating and/or operating the Procomp WLAN card solution for IEEE 802.11b/g in a
Microsoft Windows environment and the Procomp WLAN Driver and Utility. This guide
also provides information for users who wish to upgrade the Procomp NDIS driver from
previous releases. This guide describes the steps required to install NDIS drivers for the
Procomp Wireless Network Adapter in Windows 2000, Windows XP, Windows Millennium
Edition, Windows 98SE.
About this Document
Chapter 1 Introduction—Hardware, software, and system requirements needed to set up the
Procomp Wireless Network Adapter.
Chapter 2 Installation—Installation/uninstallation procedures for Windows XP, Windows
2000, Windows ME, Windows 98SE.
1
Introduction
The Procomp Wireless Network Adapters are designs based on the Inprocomm IPN2220 and
Maxim 2825 chip set. These designs implement a half-duplex, Orthogonal Frequency
Division Multiplexing (OFDM) baseband processor supporting all IEEE 802.11g data rates (6
to 54 Mbps) and 802.11b data rates (1 to 11 Mbps). The host interface is compatible with the
PC Card 7.1 and PCI 2.3 standards.
System Requirements
Laptop PC containing:
•
32-bit CardBus slot (or Desktop PC with PC Card-PCI adapter)
•
32 MB memory or greater
•
300 MHz processor or higher
Microsoft Windows 2000/Windows Millennium Edition/Windows 98 Second
Edition/Windows XP
2
Installation
This chapter describes using the Procomp installer to install the Procomp WLAN Driver and
Utility. Procomp provides an InstallShield utility to upgrade the NDIS driver, if a previous
release is installed, and to install the Procomp WLAN Driver and Utility.
•
Use the Procomp WLAN Driver and Utility to configure the device driver.
•
Use the InstallShield Updater to uninstall the NDIS driver and Procomp WLAN
Driver and Utility application and remove them from the Device Manager.
Procomp WLAN Driver and Utility Installation and Driver Update
This section describes installing the client utility and driver on the Windows XP, Windows
2000, Windows ME, and Windows 98SE OSs.
To install the Procomp WLAN Driver and Utility:
1. Copy the driver package (ex: setup.exe) to any directory of Notebook or PC. It can be
run on the Windows XP, Windows 2000, Windows ME, and Windows 98SE OSs.
2. Click the package “setup.exe” to appear the installation dialog.
3. Click the “Next” icon to continue the installation. If no previous installation exists, the
dialog will appear.
4. Click “I accept the terms in the license agreement” shown as in Figure 1. If previous
installation is found as shown in Figure 2, chose the desire option from “Modify, Repair”,
and “Remove”.
Figure 1. License Agreement Dialog
Figure 2. Modify, Repair, and Remove Option Dialog
5. Click “Install” to install the program.
6. Click the “Continue Anyway” to complete the installation of “Procomp WLAN Driver
and Utility”.
Driver Installation
This section describes the installation for the Windows driver on the Windows XP, Windows
2000, Windows ME, and Windows 98SE OSs.
To install the driver:
1. Insert the Procomp Wireless Network Adapter into a 32-bit CardBus slot.
2. Wait for the “Found New Hardware Wizard” dialog box to appear as Figure 3. Choose
the recommended method to “Install the software automatically,” and click “Next” to
continue.
Figure 3. Windows Found New Hardware Dialogue
3. The Procomp NDIS evaluation driver currently does not have a digital signature from
Microsoft. Therefore, Windows may show a warning message shown as Figure 4. Click
“Continue Anyway” to proceed with driver installation.
4. If the “Found New Hardware Wizard” dialog box doesn’t appear, run the “Add/Remove
Hardware” in the “Control Panel”. Click the option to install the driver manually by
browsing the created directory and selecting the “IPN2220.inf”.
Figure 4. Windows Digital Signature Warning
5. Click “Finish” to complete driver installation.
Federal Communication Commission Interference Statement
Federal Communications Commission (FCC) Requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
FCC RF Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
Regulatory information / Disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with the
instructions included in the user documentation provided with the product. Any changes or
modifications (including the antennas) made to this device that are not expressly approved by
the manufacturer may void the user’s authority to operate the equipment. The manufacturer is
not responsible for any radio or television interference caused by unauthorized modification
of this device, or the substitution of the connecting cables and equipment other than
manufacturer specified. It is the responsibility of the user to correct any interference caused
by such unauthorized modification, substitution or attachment. Manufacturer and its
authorized resellers or distributors will assume no liability for any damage or violation of
government regulations arising from failing to comply with these guidelines.
CE Warning:
Regulatory statement ( R&TTE / WLAN IEEE 802.11 b/g )
European Standards dictate maximum radiated transmit power of 100mW EIRP and
frequency range 2.400-2.4835GHz; In France, the equipment must be restricted to the
2.4465-2,4835GHzfrequency range and must be restricted to indoor use.
CE Declaration of Conformity:
For the following equipment: Wireless LAN CardBus
0984
Is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
(89/336/EEC),
Is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
(89/336/EEC), Low-voltage Directive (73/23/EEC) and the Amendment Directive
(93/68/EEC), the procedures given in European Council Directive 99/5/EC and 89/3360EEC.
The equipment was passed. The test was performed according to the following European
standards:
EN 300 328-2 V1.2.1 (2001-08)
EN 301 489-1 V.1.4.1 (2002-04) / EN 301 489-17 V.1.2.1 (2002-04)
EN 50371: 2002
EN 60950: 2000

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:04:14 10:11:32+08:00
Modify Date                     : 2004:04:14 10:11:32+08:00
Page Count                      : 9
Creation Date                   : 2004:04:14 02:11:32Z
Mod Date                        : 2004:04:14 02:11:32Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : TingLin
Metadata Date                   : 2004:04:14 02:11:32Z
Creator                         : TingLin
Title                           : Microsoft Word - User's Manual with WArning Statement.doc

EXIF Metadata provided by EXIF.tools