Pronto Networks PIAP Pronto Intelligent Access Point User Manual User muanal

Download:
Mirror Download [FCC.gov]
Document ID	2731391
Application ID	pzCHnZHb/TfX7PBRadmhGQ==
Document Description	Manual r1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	93.45kB (1168154 bits)
Date Submitted	2015-08-29 00:00:00
Date Available	2015-10-06 00:00:00
Creation Date	2015-08-26 19:38:22
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2015-08-26 19:38:22
Document Title	Microsoft Word - User muanal
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

User Manual
of
Pronto Intelligent Access Point
This is the manual of outdoor CPE, which will approximate guide you how to set and apply the outdoor CPE, it provide
a convenient graphical interface for network construction and maintenance person, as well as a user through a simple
and accurate operation, and configuration management of the CPE.
1 s t Connection and Power Supply
1 s t ： P o r t C o n n e c t i o n a n d p ow e r s u p p l y
Instruction of different port：
P1

CPE Port Connection
Please use a power supply of 12V DC adapter or 24V POE adapter, WAN / LAN port is the PoE Port.
Pls make sure the CPE’s power supply is normal in reset process, or the CPE will be
Pay Attention

damaged and can’t reboot
Reset:
There are two ways to reset the CPE:
1.
CPE Manage page: Click “Management”, then “Save/Reload Settings”, then click“Reset Settings”to
finish the CPE Reset
P2 CPE Reset
2. Press the Reset Button on CPE more than 15 seconds, then release, the device will reboot and restore to
factory settings

The connection way of CPE, PoE Adapter and PC:
P3
Pay Attention
Connection diagram of CPE and PoE adapter
Incorrect Connection or the use power adapter and PoE adapter not from our
factory, the CPE will be damaged
2 n d Steps： Login
1）Connect the CPE with computer as P2 picture
2）Configure the PC’s local connection IP address as 192.168.188.X (X is number from 2 to 254), subnet mask is
255.255.255.0, follow P4 and P5 to finish.
P4 Setting of computer’s IP address
P 5 Setting of computer’s IP address
3) Input 192.168.188.253 into IE browser, then pop up the login page, the default login user name: Admin,
Passwords: admin, pls do following P5
P6 Login
4) After login, then P6 Device Status will be showed:
P7: Device Status
There are four operation mode showed on this page:
Gateway mode, Repeater Mode, AP Mode and WISP Mode;
3rd：Quickly Configure CPE
①
Gateway Mode:
Click “Gateway Mode” under following picture and choose the right WAN access type, then input the right SSID,
Channel, key as like.
P8 Gateway Mode
②
WiFi Repeater and Station operation configuration
A. Login the Web management page, click “ Repeater Mode”, then “Scran AP”
P9 Repeater Mode
B. Select the AP’s SSID want to bridge, take SR800-5.8G for example.
P10 Select AP
Instruction
If your computer can’t pop up this window, pls check your IE explorer and see whether it is blocked
already. And if this CPE can’t scan any SSID, pls check if there are 5G wireless signal.
C. input the AP’s key, and apply changes
P11 Repeater Mode
D. In Repeater Mode, the SSID is disable in default setting, it work as Station; Then if need SSID broadcast in this
operation mode, just manual to change under Advanced Settings, So, click sure in this part to finish the repeater
operation mode setting.
P12 Notice
E. After this step, can click the Device status to check the status of this CPE. And it will show CPE’s LAN Interface,
WLAN status and Sigbal Strength.
P 13 Device Status
F. Then if SSID should be broadcast under repeater mode, pls click “Advanced Settings” , then “5.8GHz Repeater” will
pop up.
If want to bridge another AP’s SSID, then can setup in this part and Aplly changes.
P14 5.8G Repeater
G. Click “5.8GHz Virtual AP”, will shwo SSID shut off, if need SSID broadcast, pls follow steps of 1,2,3,4,5,6 showed in
following picture. This CPE will work under wireless repeater and broadcast SSID after apply changes.
P15 5.8GHz Virtual AP
③
AP Mode
Plug and Play to transmit wireless signal for wireless end users form wired networking. In this part, user can mark
the AP’s location and name for easy problem checking. Then can change SSID, Key, Channel as request.
P16 AP Mode
④
WISP
In this operation mode, user should confirm the WAN access type at first, then set the SSID, key, Channel as request.
P17 WIPS Mode
⑤
Advanced Settings:
1. System Status
Click “ Advance Settings”, will show system status, such as firmware version, build time, System uptime...
P18 System Status
Click 5.8GHz Wireless Status, will show CPE’s WLAN Status, Signal Strength, SSID...
P19 5.8GHz Wireless Status
If want to check LAN status, pls check following picture
P20 LAN Status
2. Operation Mode:
Set operation mode manually, choose the right operation mode, then apply changes. The function of this part will
be same as Quick Setup step.
P21 Operation Mode
3. 5.8GHz Repeater:
In this part, use can scan AP’s SSID, disable or enable CPE’s SSID, modify Channel, Country code, Key..
P22 5.8GHz Repeater
United States
P23 5.8GHz Advanced
Note: The frequency selection feature is disabled by firmware for devices marketed to the US. only channels 1-11 will
be used in North America. Country code selection is disabled.
4. Network Setting
LAN Interface Setup mainly showed as follow:
P24 Network Setting
5. Management
In this part, user can set Time zone, show Log info, upgrade firmware, change login user name and password;
(GMT+13)United States
P25 Management
6. Upgrade Firmware
Pls click Upgrade Firmware, then browse and choose the firmware should upgrade, then click upgrade to upgrade the
firmware.
P26 Firmware Upgrade
After finish firmware upgrade, pls click Save/Reload Settings, then reset settings to default.
After that, the firmware upgrade is finished.
7. Share Internet and Obtain IP address automatically
Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as
following picture showed. the computer will obtain the IP address from router or base station to get Internet.
Tr o u b l e S h o o t i n g :
F 1 The Failure phenomenon and solution
Failure phenomenon
SYS Indicator off
Can’t land to CPE through Web page
CPE can’t connect with AP
（the status display unconnected）
Can’t scan the wireless AP
The connection of CPE and AP is
success, but the computer can’t share
internet
How to Reset CPE
Solution
Pls make sure the PoE module connection is right. POE Port
connect with CPE, LAN port connect with computer
Pls check the IP address of computer and CPE to see whether they
are in same networking segment, The method is click “start”-“Run”
input“cmd”，ping 192.168.188.253 to test the CPE connectivity.
Reset CPE and load it again;
Pls make sure the IP address 192.168.188.253 is not occupied by
other device in CPE’s networking;
Check computer and cable problem, recommend to use 10/100M
UTP unshielded cable;
Clean up Arp binding from “Start”-“Run” input“cmd” arp –d
Clean the IE Brower’s temporary files and Cache file。
Try to scan the avaliable wireless networking again；
Make sure the CPE’s wireless standard is correct；
The Security and passwords are matched between CPE and AP；
The signal strength of AP is too weak to connect, should be more
than -75dBm；
Scan it several times more；
Make sure there are 5G signal existed.
Reset the CPE, scan it again after CPE restart；
Pls Check the computer’s IP address and DNS setting. If it is
dynamin, set the network card as automatically obtain. If it is static
IP, pls contact with ISP for correct IP address and DNS address.
Press the “Reset” button more than 15 seconds after power on. The
CPE will restore factory default after the CPE restart.
Note:
*. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : Administrator
Create Date                     : 2015:08:26 19:38:22+08:00
Modify Date                     : 2015:08:26 19:38:22+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - User muanal
Creator                         : Administrator
Document ID                     : uuid:9aaea96c-8d2c-4961-8795-a36c09e31e23
Instance ID                     : uuid:7009328b-643c-4f3b-af03-a1b6cb238df8
Page Count                      : 17

EXIF Metadata provided by EXIF.tools