101444_Versa'larm 1 Zone_Installation Instructions__Comp 552761 2 Alderon Versalarm Tank Alarm Installation Manual
552763 2 Alderon Versalarm Tank Alarm Installation Manual 552763_2_Alderon Versalarm Tank Alarm Installation Manual
552766 2 Alderon Versalarm Flood Alarm Installation Manual 552766_2_Alderon Versalarm Flood Alarm Installation Manual
552767 4 Alderon Versalarm Sump Alarm Installation Manual 552767_4_Alderon Versalarm Sump Alarm Installation Manual
552762 2 Alderon Versalarm Tank Alarm Installation Manual 552762_2_Alderon Versalarm Tank Alarm Installation Manual
552764 2 Alderon Versalarm Tank Alarm Installation Manual 552764_2_Alderon Versalarm Tank Alarm Installation Manual
: Pump 552761 2 Alderon Versalarm Tank Alarm Installation Manual 552761_2_Alderon Versalarm Tank Alarm Installation Manual pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Versa’larm TM 1 Zone Alarm - Model VA01A Operation, Maintenance and Installation Manual Introduction Power Alarm Alarm Test Alarm Silence Silence Before proceeding with the installation or operation of the Versa’larm™, read all instructions thoroughly, as well as complying with all Federal, State and Local Codes, Regulations and Practices. The Versa’larm must be installed by qualified personnel familiar with all applicable local electrical and mechanical codes. Refer to the National Electrical Code (NFPA 70). Failure to properly install and test this product can result in personal injury or equipment malfunction. The Versa’larm is a multipurpose alarm that can be used in a wide variety of applications such as: septic tanks, sumps, holding tanks, pump chambers, water tanks, flow, pressure, condensate, temperature and any other application where a “dry” contact can be connected to the Versa’larm. These contacts can be connected to an Auto Dialer, a BAS (building automation system) or SCADA system. Safety Guidlines 1. DO NOT USE WITH FLAMMABLE OR EXPLOSIVE FLUIDS SUCH AS GASOLINE, FUEL OIL, KEROSENE, ETC. DO NOT USE IN EXPLOSIVE ATMOSPHERES. 2. VERSA’LARM MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY. Description of Operation The Versa’larm is powered by 120 VAC coming from standard wall outlets and is transformed to 9-11 VDC. Installing a 9 volt battery provides battery backup. When a switch (signaling device) contact “closes” the buzzer and alarm light will turn “on” and the built in auxiliary contacts will be activated. The signaling device could be a control duty float switch (e.g. Unimax™) or a water sensor (e.g. WaterSpotter™, WaterSpotter™ Probe, Alderon Temperature Switch). Pressing the “silence” switch deactivates the buzzer. When the alarm is remedied, the system automatically resets itself. Tools, Supplies and Requirements for Installation (Not Included) 1. 2. 3. 4. 5. 6. 7. Phillips screw driver (Qty 2) #6 self tapping screws Access to 120 VAC power receptacle Optional - Plastic anchor if mounting to sheet rock Optional - 9V battery (used for battery backup if power goes out) Optional - Wire stripper (used if you need to strip wire to connect to a BAS or SCADA system) Optional - Needle nose pliers if using auxiliary contacts The Versa’larm is packaged as a stand alone item or with the specific sensor(s) you ordered it with. Other part numbers and accesories are available. See catalog/website for more details. Examples below: Power Alarm Power Alarm Alarm Test Alarm Silence Silence Alarm Test Alarm Silence 7013 Alarm Systems Silence Unimax Control Float 7001 Control Panels Power Alarm Power Alarm Power Alarm Alarm Test Alarm Silence Silence Alarm Test Alarm Silence Silence Alarm Test Alarm Silence 7002 Float Switches Silence Unimax Control Float 7003 7011 Leak Detection Systems P/N: 101444 Power Alarm Alarm Test Alarm Silence Silence 7151 Page 1 of 4 PO Box 827 Hawley, MN 56549 (218) 483-3034 Fax (218) 483-3036 www.alderonind.com Versa’larm TM 1 Zone Alarm - Model VA01A Operation, Maintenance and Installation Manual Installation of the Versa’larm 1. To install/replace the battery for the backup power feature, remove the access cover (Fig. 1) and install 9 VDC battery (Duracell model MX 1604B2) (Fig. 2). After installing battery, press the test button (Fig. 3) to activate the alarm to make sure the battery works properly. The alarm indicator light should illuminate and the buzzer should annunciate. If using the auxiliary contacts, leave cover off until Step 4 is completed. If you are not using the auxiliary contacts, replace the access cover (Fig. 4). Remove Cover To Insert 9v Battery. Replace Yearly. Auxiliary Contacts Inside. Remove Cover To Insert 9v Battery. Replace Yearly. Auxiliary Contacts Inside. Remove Cover To Insert 9v Battery. Replace Yearly. Auxiliary Contacts Inside. (Fig. 1) (Fig. 2) (Fig. 3) (Fig. 4) 2. Determine mounting location for the Versa’larm. Make sure the power outlet is within 5 feet of the Versa’larm (Fig. 5). Make sure the outlet is on a separate circuit breaker from any other device and not on a switched receptacle to maintain power integrity. Mount the Versa’larm using two #6 self tapping screws (not included) (Fig. 6). Use #8 plastic anchor (not included) if mounting to sheet rock (Fig. 7). 5 ft max (Fig. 5) (Fig. 7) (Fig. 6) 3. If you are not using the auxiliary contacts, go to Step 6. If using auxiliary contacts (Fig. 8), when a sensor such as a float switch in a septic tank, a WaterSpotter™ near a floor drain or in your sump pit is activated, it will close relay contacts on Terminals 1A and 1B and activate the Auto Dialer. If connecting to existing alarm security system or BAS system, go to Figure 9 on Page 3. When connected, replace the access cover and pull the wires through the knockouts on the access cover (Fig. 10 and Fig. 11), see Step 5. Caution! - When installing wires, route all wires away from sharp objects and internal components. + - 1A 1B Terminals 3 and 4 Auto Dialer Contacts YELLOW = 1A WHITE = 1B Alarm Systems (Fig. 8) To Phone Line Control Panels +- 1A 1B (+) (-) (1A) (1B) Terminals 1 and 2 Auto Dialer Power Supply RED = “+” BLACK = “-” Float Switches Leak Detection Systems P/N: 101444 Page 2 of 4 PO Box 827 Hawley, MN 56549 (218) 483-3034 Fax (218) 483-3036 www.alderonind.com Versa’larm TM 1 Zone Alarm - Model VA01A Operation, Maintenance and Installation Manual Installation of the Versa’larm Continued 4. If connecting to existing alarm security system or BAS system leave Terminals “+” and “-” open and use 18 AWG 2 conductor wire to connect the existing product to Terminals 1A and 1B (Fig. 9). When connected, replace the access cover and pull the wires through the knockouts on the access cover (Fig. 10 and Fig. 11), see Step 5. Caution! - When installing wires, route all wires away from sharp objects and internal components. + Terminals “+” and “-” DO NOT USE Class 2, 24 VDC/VAC (50/60 Hz) 100 Milliamps MAXIMUM 1A 1B (Fig. 9) BAS (Building Automation System) or another high water alarm or any monitoring system + - 1A 1B (1A) and (1B) Terminals 1A and 1B Normally Open - NOTE: The auxiliary contacts on Terminals 1A and 1B of the Versa’larm are Normally Open only. 5. Use a needle nose pliers (not included) to remove the desired “break away tabs” from the access cover, lightly pull and twist off tab(s) (Fig. 10). Run the wires through the knockouts when replacing the access cover (Fig. 11). (Fig. 11) (Fig. 10) Remove Cover To Insert 9v Battery. Replace Yearly. Auxiliary Contacts Inside. Remove Cover To Insert 9v Battery. Replace Yearly. Auxiliary Contacts Inside. Remove Cover To Insert 9v Battery. Replace Yearly. Auxiliary Contacts Inside. 6. Make note of the alarm condition(s) you are monitoring and keep near the alarm. Alarm Systems Control Panels Float Switches Leak Detection Systems P/N: 101444 Page 3 of 4 PO Box 827 Hawley, MN 56549 (218) 483-3034 Fax (218) 483-3036 www.alderonind.com Versa’larm TM 1 Zone Alarm - Model VA01A Operation, Maintenance and Installation Manual Installation of the Versa’larm Continued 7. Connect any combination of switches (rated 9 VDC, 200 mA MINIMUM) (Fig. 12) such as a float switch, pressure switch, WaterSpotter™, WaterSpotter™ Probe, etc. to Terminals C and 1 on the terminal block of the Versa’larm. TERMINAL 2 IS NEVER USED. The alarm is activated by a closed switch. Caution! - When installing the “signaling switch”, refer to its installation instructions for proper installation. Terminals C and 1 (Fig. 12) Unimax™ - Float Switch BLACK = 1 WHITE = C X WaterSpotter™ & WaterSpotter™ Probe BLACK = 1 RED = C Unimax Control Float X Unimax Control Float Black 2 Red C Unimax Control Float White C Red C Red C Black 1 Black 1 Black 1 White C Red C Black 1 White C Versa’larm™ Accessory (P/N: 7933) Indoor/Outdoor LED Strobe Beacon X Black 1 Black 1 X Combination of Sensors BLACKS = 1 REDS / WHITES = C Use 18 Gauge wire and connect the Red wire to Terminal “C” and Black wire to Terminal “2”. 5 ft max 8. Plug the power supply into a 120 VAC, 50/60 Hz standard wall outlet. The green “Power” light should come on. 9. Test the system by pressing the “Test” switch or by activating the “Signaling Device” (Fig. 13). The buzzer and the red alarm light will be “on”. Press the “Silence” switch, the buzzer will silence but the alarm light will remain “on”. Deactivate the “Signaling Device”, the alarm light will turn “off”. Since the Versa’larm is equipped with “Auto Reset”, reactivating the “Signaling Device” for a new test cycle will reactivate the buzzer and alarm light. Test product weekly to ensure system integrity. (Fig. 13) OR ax Unim l Contro Float Alarm Systems Control Panels Float Switches Leak Detection Systems P/N: 101444 Page 4 of 4 PO Box 827 Hawley, MN 56549 (218) 483-3034 Fax (218) 483-3036 www.alderonind.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2015:09:21 12:06:15-05:00 Creator : Adobe Illustrator CC 2015 (Macintosh) Modify Date : 2016:06:08 12:05:29-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29 Metadata Date : 2016:06:08 12:05:29-05:00 Creator Tool : Adobe Illustrator CC 2015 (Macintosh) Thumbnail Width : 212 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 22730 bytes, use -b option to extract) Format : application/pdf Title : 101444_Versa'larm 1 Zone_Installation Instructions_Page 1_Comp Document ID : xmp.did:f88202a6-f6be-4c5a-abe6-0cf503910992 Instance ID : uuid:23dcbeaa-52b3-5c4e-a3dc-1a19db2177b1 Original Document ID : uuid:48b1a93b-942e-4c1a-82f2-bae0c403ea43 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:67e059b1-7424-4f67-b02b-8a3f3585e984 Derived From Document ID : xmp.did:67e059b1-7424-4f67-b02b-8a3f3585e984 Derived From Original Document ID: uuid:48b1a93b-942e-4c1a-82f2-bae0c403ea43 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:56b4cd7b-1963-4a77-83dc-4206ef938a9d, xmp.iid:f88202a6-f6be-4c5a-abe6-0cf503910992 History When : 2014:05:12 11:06:24-05:00, 2015:09:21 12:06:10-05:00 History Software Agent : Adobe Illustrator CC (Macintosh), Adobe Illustrator CC 2015 (Macintosh) History Changed : /, / Manifest Link Form : EmbedByReference Manifest Reference File Path : /Volumes/Share/Graphic Design/Work Files/Warning Logo/Warning Logo.eps Manifest Reference Document ID : xmp.did:73E7F05CD739E4118DFC8A9FC91177D2 Manifest Reference Instance ID : xmp.iid:73E7F05CD739E4118DFC8A9FC91177D2 Ingredients File Path : /Volumes/Share/Graphic Design/Work Files/Warning Logo/Warning Logo.eps Ingredients Document ID : xmp.did:73E7F05CD739E4118DFC8A9FC91177D2 Ingredients Instance ID : xmp.iid:73E7F05CD739E4118DFC8A9FC91177D2 Producer : Adobe PDF library 15.00 N Pages : 1 Has Visible Transparency : True Has Visible Overprint : True Max Page Size W : 8.500000 Max Page Size H : 11.000000 Max Page Size Unit : Inches Font Name : MyriadPro-Regular, NovareseStd-Bold, Helvetica, Impact Font Family : Myriad Pro, ITC Novarese Std, Helvetica, Impact Font Face : Regular, Bold, Regular, Regular Font Type : Open Type, Open Type, TrueType, Open Type Font Version : Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, OTF 1.018;PS 001.002;Core 1.0.31;makeotf.lib1.4.1585, 10.0d1e1, Version 5.00x Font Composite : False, False, False, False Font File Name : MyriadPro-Regular.otf, NovareseStd-Bold.otf, Helvetica.dfont, Impact.ttf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE Black M, PANTONE 540 M Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Swatch Colorant Swatch Name : PANTONE Process Black C, PANTONE 465 CVC, PANTONE Black C, PANTONE 540 M, PANTONE 466 C, PANTONE P 179-3 U, PANTONE P 20-8 U, PANTONE Red 032 M, PANTONE 809 M, PANTONE 5295 M, PANTONE 102 M, PANTONE Black M Swatch Colorant Type : SPOT, SPOT, SPOT, SPOT, SPOT, PROCESS, PROCESS, SPOT, SPOT, SPOT, SPOT, SPOT Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Swatch Colorant Mode : CMYK, CMYK, Lab, CMYK, Lab, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Cyan : 0.000000, 18.431100, 100.000000, 0.000000, 0.000000, 0.000000, 10.000000, 20.000000, 0.000000, 0.000000 Swatch Colorant Magenta : 0.000000, 30.587801, 55.000001, 0.000000, 50.000000, 89.999998, 0.000000, 15.000001, 0.000000, 13.000000 Swatch Colorant Yellow : 0.000000, 56.079102, 0.000000, 0.000000, 100.000000, 86.000001, 100.000000, 0.000000, 94.999999, 49.000001 Swatch Colorant Black : 100.000000, 0.000000, 55.000001, 20.000000, 0.000000, 0.000000, 0.000000, 10.000000, 0.000000, 98.000002 Swatch Colorant L : 17.254902, 71.372551 Swatch Colorant A : 1, 7 Swatch Colorant B : 3, 30 Page Count : 4EXIF Metadata provided by EXIF.tools