RELM Communications RPV599A VHF FM Transceiver User Manual Manual0628

Download:
Mirror Download [FCC.gov]
Document ID	291483
Application ID	Mz4jlScw7MD0Xmt5sga6Qg==
Document Description	users manual with programming manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.68kB (920962 bits)
Date Submitted	2002-12-20 00:00:00
Date Available	2002-12-23 00:00:00
Creation Date	2002-12-20 11:55:54
Producing Software	Acrobat PDFWriter 4.05 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	Manual0628.PDF
Document Creator	Microsoft Word
Document Author:	jennifer

User Manual
For RPV599A Programming Software
Version 1.00
² Introduction
RPV599A Programming Software described in this user manual is applicable to RPV599A
Transceiver. This software is mainly used for writing data to your transceiver or reading data from
your transceiver via your computer and copyrighted by Relm Corporation.
² Statement
“It is forbidden to transmit this device on marine frequencies 156.10 MHz (Marine Channel 02), 156.20
MHZ (Marine Channels 04 and 04A), 156.025 MHz (Marine Channel 60), and 156.125 MHz (Marine
Channel 62).”
Programming software, accessories, and procedures are issued only to authorized distributors and
repair facilities. The radio cannot be programmed for any frequency change, including channel
spacing (12.5/15 kHz vs. 25/30 kHz), by a user in the field.
² Install Software
In your disk, which is presented to you together with your transceiver, you can see one setup file of
our software, which is named by RPV599ASetup.EXE. By clicking the setup file, installing will run
automatically. During the installing process, you can do something according to the setup wizard.
When finished, the software has been installed in your computer.
² Connect a Cable
After installing the software, but how to use it with your transceiver
You will have a cable that connects your computer with your transceiver. You can connect your
computer to your transceiver according to the following steps.
Insert one end of the cable to the serial port (COM1 or COM2) of your computer, the other end to
the Speaker/Microphone “ port of the transceiver. Before operating the transceiver, you are
required to open the power switch of the transceiver.
² Run Software
There is a shortcut to it on your computer Desktop and Program Manager group. Execute this
shortcut “RPV599A Programming Software“ to run the program. The Main Interface displays as
follow.
Figure 1
² Select Communication Port
When changing the connecting serial port, you must select the corresponding communication
settings. To select a different communication port, click Communication of Option Menu and set a
new port.
Figure 2
When popuping the dialog, you can choose either COM1 or COM2 as your communication port.
Figure 3
²
Set the data
Channel Unit Settings
When you run the program, you can see three different interfaces by clicking the Option menu
item. The first submenu of Channel Settings is for setting the channels data; the second submenu
of Radio Configuration is for setting the whole radio function data and scan data; the last submenu
of Set DTMF/TTS is just for setting radio signals: DTMF or TTS(Two-Tone Signaling).
In the main interface, you can see a form of the first 20 channels. There are fives group and each
group has 20 channels except for the fifth group. In each main interface you can set the channel
data. There are 13 columns for each channel. You can set each column with your wanted value. In
the top of the main interface, you can see two buttons which are named Prev and Next.
By clicking either button, the main interface will be changed to the next group of 20 channels.
Radio Configuration
Now if you click the submenu item of Radio Configuration under Option menu item, you will see a
new interface. In this interface you can set all the whole radio settings as bellows.
Figure 4
Ÿ Model
There are two items. This program is just for one model of transceiver RPV599A. The frequency
band is 148MHz~174MHz.
Ÿ Scan Information
You can set all the data relevant to scan. The value of each item is listed in the Combo Box.
Whole Radio Settings
In this frame, you can set all the function data. The value of each item is also listed in the Combo
Box. Here you will be reminded to notice the last two items Rx TTS(A) and Rx TTS(B). These two
items is to set the TTS tone frequency for the radio.
Ÿ Key Program
In this frame, you can set different functions for the six keys on the panel of the radio.
Each key can be set to be any of the six functions.
N o t e : You’d better not set more one key to be the same function.
Set DTMF/TTS
If you want to set DTMF/TTS, you can click another submenu item Set DTMF/TTS. In this
interface, you see two frames. One is DTMF and the other is TTS. You can set any data for them.
Figure 5
Ÿ DTMF
In this frame, you can set all the DTMF data settings. The value each DTMF item is listed in
combo box except for Connect ID and Disconnect ID. These two items need you to enter the code
number when you want.
Ÿ TTS
In this frame, you can set all the tone frequency and tone time for TTS.
In the two above interfaces, you will see there are two buttons on the bottom of the interface,
which are OK and Cancel. When you finish to set all your wanted data, you can click the OK
button to save them. If you have just take a mistake to modify them, you can click the Cancel
button to restore the old data.
S e e t h e H e l p Fi l e f o r d e t a i l s a b o u t S e t t h e D a t a .
² Read the Data
Select the Operate Menu and click the Read item, you will read frequencies and other data of the
transceiver connecting to your computer when you open its power switch. Of course, you can also
click Read Icon of Toolbar.
While reading, the program display the following figure.
Figure 6
Display as follow if data are read correctly.
Figure 7
² Write the Data
If you need to write frequencies and other data to the transceiver, select the Operate Menu and
click Write item, or click Write Icon of Toolbar.
While writing, the program popup the following figure.
Figure 8
If data are written correctly, display:
Figure 9
² Other Operation
Open a File
When you set all the data, you can save them to be a file which extend file name is .rpv. When you
need these data, you open the file which has been saved by clicking the submenu Open under the
menu File(F). The figure is as follows.
Figure 10
Save
Clicking this submenu or icon, you can directly save the data in your opened file. If you don’t open
any file, clicking it will popup a Save dialog to recommend you to save them in a new file.
Save As
Clicking this submenu or icon, you can save all the data to be a new file under any condition. You
can enter any new name for it. The figure is as follows.
Figure 11
Print
If you want to print your data, you can click the icon Print. You can just print the data of the current
interface once a time.
Additionally,
when you open a file, the menu of File will display the file. The submenu can display
the last four files that have been opened. If you want to open any of these four files, you can click
it.
Figure 12

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 5
Creator                         : Microsoft Word
Create Date                     : 2002:12:20 11:55:54
Title                           : Manual0628.PDF
Author                          : jennifer
Producer                        : Acrobat PDFWriter 4.05 for Windows

EXIF Metadata provided by EXIF.tools