Radio Shack 2101706 40-Channel Citizen Band Transceiver User Manual 21 1706

RadioShack Corporation 40-Channel Citizen Band Transceiver 21 1706

User Manual

Owner’s ManualPlease read before using this equipment.40 Channel Mobile CBwith Digital Compass, and EL Backlit LCD Display21-1706.fm  Page 1  Wednesday, January 9, 2002  8:37 AM
2FeaturesXFeaturesYour RadioShack 40 Channel Mobile CB is a great way to communicate with other CB radio operators. You can mount it in a vehicle for mobile use, or in your home for use as a base station.Your CB has these advanced features:LCD display with EL backlight on display and controls — lets you see the CB’s operating status at a glance and helps you easily see the display and controls when you use the CB at night.Digital Compass — aids navigation on the road.Emergency Channel One Touch Access — lets you quickly switch to Channel 9 or 19 so you can monitor or report emergency situations.3 Channel Memories — let you easily access your favorite channels.Last Channel Recall (RCL) — Lets you quickly recall the last channel used.Dual Channel Controls — let you tune the channel from the transceiver or the microphone.RF Gain Control — lets you adjust the receiver’s gain to match the strength of the signal.Phase-Locked Loop (PLL) Frequency Synthesizer — provides highly accurate and stable tuning.Two Built-In Ceramic Filters — ensure superior channel selectivity and freedom from adjacent channel interference.Automatic Modulation Control — prevents the transmitter signal from over-modulating and distorting.Automatic Noise Limiter — reduces impulse-type noises while receiving.Built-In PA (Public Address) Amplifier — lets you use your CB as a public address system when you add an optional PA speaker.Universal Mounting Bracket — lets you mount your CB securely in your vehicle.Note: To use this CB, you must connect a mobile or base station antenna. Your local RadioShack store has a wide variety of antennas. For more information, see “Connecting an Antenna” on Page 4.FCC INFORMATIONThe Federal Communications Commission (FCC) does not require you to have a license to operate this CB radio. However, you must know Part 95 of FCC Rules. It explains the proper operation of a Class D citizen’s band transceiver. We enclosed a copy of Part 95 with your CB radio.Warning: Do not open the CB radio to make any internal adjustments. A CB radio is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the unit to exceed these limitations.To be safe and sure:• Never open your CB radio’s case.• Never change or replace anything in your CB radio.© 2002 RadioShack Corporation.All Rights Reserved.RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.21-1706.fm  Page 2  Wednesday, January 9, 2002  8:37 AM
3InstallationYour CB radio might cause TV or radio interference even when it is operating properly. To determine whether your CB is causing the interference, turn off your CB. If the interference goes away, your CB is causing it. Try to eliminate the interference by:• moving your CB away from the receiver• contacting your local RadioShack store for helpThis device complies with Part 15 of the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.XInstallationATTACHING THE MICROPHONE HOLDERYou can attach the microphone holder to the right side of the transceiver or to another location in your vehicle.To attach the holder to the transceiver, secure the holder to the right side using the supplied 3 mm screws and lock washer.To attach the holder to another location in the vehicle, such as the dashboard, follow these steps.1. Using the holder as a template, mark the positions for the mounting screw holes at the desired location.2. At each marked position, drill a small starter hole.Caution: Be careful not to drill into anything behind the mounting surface.3. Attach the holder at the mounting location using the supplied machine screws, spring washers, plain washers, and nuts.Note: If you cannot reach behind the mounting surface to attach the nuts on the machine screws, use the supplied 3 mm plain washers and self-tapping screws.MOUNTING THE TRANSCEIVERThe most common mounting location for this CB is under a vehicle’s dashboard. However, if you plan to use the CB as a base station, you can place it on a desk, shelf, or table (see “Using the Transceiver as a Base Station” on Page 6).If you are mounting the CB in a vehicle, choose a location where:• You can easily reach the CB.• Wires and cables are clear of the vehicle’s pedals or other moving parts.21-1706.fm  Page 3  Wednesday, January 9, 2002  8:37 AM
4Installation• The CB is not directly in front of heating vents.• All wires and cables can reach their connection points.Warnings:• If you use the CB in a vehicle, mount it securely to avoid damage to the CB or vehicle or injury to anyone in the vehicle during sudden starts or stops.• Do not mount the CB where it could damage or interfere with the operation of any passive restraint safety device (an airbag or seat belt).Follow these steps to mount the CB using the supplied hardware.1. Using the mounting bracket as a template, mark the positions for the screw holes on the mounting surface.2. In each marked location, drill a small starter hole.Caution: Be careful not to drill into objects behind the mounting surface.3. Mount the bracket to the mounting surface with the supplied 5 mm bolts, spring washers, plain washers, and nuts.Note: If you cannot reach behind the mounting surface to attach the nuts on the bolts, use the supplied 5 mm self-tapping screws and plain washers to secure the bracket.4. Peel the backings off the adhesive on the back of the supplied rubber washers and attach the washers to the mounting holes on the CB. then attach the CB to the mounting bracket using the mounting knobs.CONNECTING AN ANTENNAThere are many different types of CB antennas for mobile CBs. Each type has its own benefits, so choose the one that best meets your needs. Your cal RadioShack store sells a wide variety of antennas.Note: If you are using this CB as a base station, see “Using the Transceiver as a Base Station” on Page 6.When you choose an antenna, keep in mind that, for the best performance, you should mount the antenna:• as high as possible on the vehicle• as far as possible from sources of electrical noise• verticallyOnce you choose an antenna, follow its mounting instructions. Then route the cable to the transceiver and connect the cable to 21-1706.fm  Page 4  Wednesday, January 9, 2002  8:37 AM
5Installationthe ANTENNA jack on the back of the transceiver.Cautions:• Avoid routing the cable next to sharp edges or moving parts, which might damage the cable.• Do not run the cable next to power cables or other radio antenna cables.• Do not run the cable through the engine compartment or other areas that produce extreme heat.To take advantage of your radio’s maximum range, adjust the antenna’s Standing Wave Ratio (SWR) using an SWR meter (not supplied).Follow the instructions supplied with the SWR meter and antenna to adjust your antenna’s SWR to the lowest possible value. SWR values of 2.0:1 are generally acceptable, with readings of 1.5:1 or lower being more desirable.CONNECTING THE MICROPHONEAlign the tab on the side of the supplied microphone’s plug with the notch in the microphone jack (on the side of the transceiver). Then insert the plug into the jack.Slide the microphone onto the microphone holder.To disconnect the microphone from the transceiver, press the tab on the side of the plug. Then pull out the plug.Caution: Never pull on the microphone cable.CONNECTING AN EXTERNAL SPEAKERYou can connect your transceiver to an external CB speaker, so you can hear an incoming call when you are outside your vehicle, or use the CB as a PA system.Connecting a CB SpeakerThe external speaker you use with the transceiver should have an impedance of 8 ohms and be able to handle 10 watts of power. The speaker cable must have a 1/8-inch plug.To connect the external speaker to the transceiver, insert the speaker cable’s plug into EXT SPKR on the back of the CB.Note: When you connect an external speaker, the CB’s internal speaker disconnects.Connecting a PA SpeakerThe PA speaker should have an impedance of 8 ohms and be able to handle 10 watts of power. The speaker cable must have a 1/8-inch plug.If your PA speaker meets the other specifications but does not already have a 1/8-inch plug, you can connect it using a phono plug-to-wire cable, available at your local RadioShack store.To connect the PA speaker to the transceiver, insert the speaker cable’s plug into PA SPKR on the back of the CB.Antenna21-1706.fm  Page 5  Wednesday, January 9, 2002  8:37 AM
6InstallationNote: To avoid acoustic feedback, the speaker should be at least 6 feet from the CB. If you experience feedback, avoid keying the microphone until you have moved the speaker away from the CB.CONNECTING THE COMPASSInsert the compass cable’s plug into SENSOR on the back of the CB. Do not place the compass cable near the DC cord or the antenna cable.CONNECTING AN OPTIONAL MICROPHONE/EARPHONEYou can connect an optional microphone or earphone with a 3/32-inch (2.5mm) mini plug and a 1/8-inch (3.5mm) plug to the MIC/EAR jacks on the front of the CB.To connect a headset with Voice Activated operation, we recommend you check the response sensitivity of the VOX circuit before installation. Different Voice Activation devices provide different performance results.Traffic SafetyDo not use an earphone with your transceiver when operating a motor vehicle in or near traffic. Doing so can create a traffic hazard and could be illegal in some areas.If you use an earphone with your transceiver be very careful. Do not listen to a continuous broadcast.  Even though some earphones/headphones let you hear some outside sounds when listening at normal volume levels, they still can present a traffic hazard.USING VEHICLE BATTERY POWERFollow these steps to connect the transceiver to vehicle battery power.1. Connect the red wire (with the inline fuse holder) on the back of the transceiver to a point in your vehicle’s fuse block that has power only when the ignition is in the ACC (accessory) or ON position.2. Connect the black wire to a metal part of the vehicle’s frame (chassis ground).Caution: Do not connect the black wire to a non-metallic (plastic) part, or to any part insulated from the vehicle’s chassis by a non-metallic part.USING THE TRANSCEIVER AS A BASE STATIONAlthough this transceiver is designed mainly for mobile use, you can also use it as a base station with an AC power source.For base station installation, you need these items:• 12-volt DC power supply that can supply at least 2 ampsCaution: Most 12-volt DC power supplies plug into a standard AC outlet to produce DC power. Before connecting your CB to a 12-volt DC RedBlack21-1706.fm  Page 6  Wednesday, January 9, 2002  8:37 AM
7Installationpower supply, read and follow the instructions included with the power supply.• base station antenna.• coaxial antenna cable and connectors, available at your RadioShack store. For the best performance, place the antenna as far as the cable length.Caution: To prevent damage to the CB, be sure you connect an antenna and the microphone before you use your CB.Follow these steps to install the CB as a base station.1. Mount the base station antenna as described in its owner’s manual.Warning: Use extreme caution when you install or remove a base station CB antenna. If the antenna starts to fall, let it go! It could contact overhead power lines. If the antenna touches a power line, contact with the antenna, mast, cable, or guy wires can cause electrocution and death. Call the power company to remove the antenna. Do not attempt to do so yourself!Caution: To comply with the FCC RF Exposure compliance requirements, a separation distance of at least 20.0 cm must be maintained between this device’s antenna and all persons.This device must transmit with a source-based time-averaging duty factor not exceeding 50%.Note: Installation and Operation instructions are for satisfying FCC RF Exposure compliance.2. Connect the antenna to ANTENNA on the back of the CB.3. Connect the transceiver’s black power wire to the negative (–) terminal on the DC power supply.4. Connect the transceiver’s red wire (with the in-line fuse) to the positive (+) terminal on the DC power supply.5. Connect the DC power supply to a standard AC outlet.21-1706.fm  Page 7  Wednesday, January 9, 2002  8:37 AM
8OperationXOperationBefore you use your CB, you should know how to use it effectively and courteously. “Transmission Courtesy” on Page 10 contains information that will help you get more enjoyment from your CB.RECEIVING TRANSMISSIONS AND ADJUSTING SQUELCH1. Set PA/MON/CB to CB.2. Turn SQUELCH fully counterclockwise.3. Turn RF GAIN fully clockwise.4. Turn on the transceiver by turning VOLUME clockwise until it clicks. All LCD segments appear briefly. Then the channel and HN appear.5. Rotate the channel selector, or repeatedly press (or hold down) UP or DOWN on the microphone until the desired channel appears.6. Adjust VOLUME to a comfortable listening level.7. To cut out background noise between transmissions, wait until there is no signal, then slowly turn SQUELCH clockwise until the background noise stops.Notes:• To receive very weak signals, turn SQUELCH counterclockwise. You hear noise between transmissions, but you also hear weak transmissions (those not strong enough to break through a higher squelch setting).• If you experience interference from nearby frequencies, turn RF GAIN counterclockwise to reduce the receiver’s sensitivity.To turn off the CB, turn VOLUME to OFF until it clicks.TRANSMITTINGNote: we recommend you try receiving before you transmit.Follow Steps 1–7 in “Receiving Transmissions and Adjusting Squelch.”To transmit, hold down PUSH TO TALK on the microphone. JN appears. Hold the microphone 2–3 inches from your mouth and speak in a normal tone of voice, then release PUSH TO TALK when you finish. JN disappears.To turn off the CB, turn VOLUME to OFF until it clicks.SELECTING THE EMERGENCY CHANNELImportant: Channel 9 and Channel 19 are reserved for motorist assistance and for reporting emergency information about accidents, hazardous road conditions, and so on. Always give emergency messages priority on Channel 9 or Channel 19.To select the emergency channel 9, press the channel selector once. Press again to select channel 19. / or '/ flashes. Press one more time to return to the previous selected channel.You can also select Channel 9 or 19 by turning the channel selector or pressing UP or DOWN on the microphone.To select another channel, rotate the channel selector or press UP or DOWN.21-1706.fm  Page 8  Wednesday, January 9, 2002  8:37 AM
9OperationUSING THE PA AMPLIFIERYour CB has a built-in PA (public address) amplifier. With an optional PA speaker (see “Connecting a PA Speaker” on Page 5), you can turn your radio into a mobile public address system.1. Turn on the transceiver. Set PA/MON/CB to PA. F7 appears.2. To transmit, hold down PUSH TO TALK on the microphone. Hold the microphone 2–3 inches from your mouth and speak in a normal tone of voice.3. Turn VOLUME for the desired volume level. If you hear high-pitched squeal, turn VOLUME counterclockwise until the squeal stops.Note: To avoid acoustic feedback, the speaker should be at least 6 feet from the CB. If you experience feedback, avoid keying the microphone until you have moved the speaker away from the CB.To turn off the PA amplifier, turn the transceiver off. Or, set PA/MON/CB to CB for CB communication.USING MONITORYou can use your CB as a receiver to listen to transmissions on an optional PA speaker. With a PA speaker connected, set PA/MON/CB to MON. Your CB cannot transmit and you hear sound only from the external PA speaker.USING THE COMPASSYou can easily view your current heading at a glance. There are eight cardinal points on the display — north, northeast, east, southeast, south, southwest, west, northwest. Calibration helps the compass better separate the earth’s magnetic field from the magnetic field generated by external influences (such as your vehicle), providing more accurate heading information.Calibrate the compass anytime you move it, or whenever distortion continuously appears. Before calibration, peel off the backing on one side of the tape and attach the tape to the back of the compass, then mount the compass by peeling off the backing on the other side of the tape, then press the compass onto the level mounting surface.Notes:• Before calibration, end CB transmission and make sure the CB is not tuned to the Emergency channel 9 or 19 or in PA mode.• Do not calibrate the compass near metal or a strong magnetic field.• The compass is not available in TX mode.1. Hold down CAL for a second. All eight cardinal points flash.2. Drive your vehicle in two complete circles. Be sure your vehicle is on level ground, in an open area, such as a parking lot.3. Press CAL to confirm calibrationAfter calibration, the current compass heading displays. For example, if the compass heading is south, the south cardinal point appears. Or, if the compass heading is northeast-north, the northeast cardinal point appears and the north cardinal point flashes.USING MEMORYYou can store three channels in the memory. The preset channel stored in MEM1, MEM2, and MEM3 is Channel 1. Press the memory 21-1706.fm  Page 9  Wednesday, January 9, 2002  8:37 AM
10 Operationlocation number to switch to the stored channel. The channel number, C;C and the memory location number appear.Note: When you rotate the channel selector or press UP or DOWN on the microphone to turn to the channel stored in the memory, C;C and the memory location number appear.Follow these steps to store a channel in memory.1. Select the desired channel.2. Hold down the desired memory location button for a second. C;C and the memory location number flash twice.USING LAST CHANNEL RECALL (RCL)In CB or monitor mode, press RCL to return to the last channel used for more than 3 seconds. Press RCL again to return to the previous channel.Notes: • The channel will only be saved to RCL memory when the current channel is manually turned using the rotary switch and stays on the channel for more than 3 seconds.• You cannot recall an emergency channel or a memory channel by pressing RCL.ADJUSTING THE BACKLIGHTYou can adjust the backlight by rotating DIMMER. To turn off the backlight, rotate DIMMER fully counterclockwise.TRANSMISSION COURTESYFollow these guidelines for radio courtesy when using your CB.• Wait for a pause in someone else’s transmission before you ask for a break.• If you do not receive an answer to your call after a second attempt, sign off and wait several minutes before trying again.• Do not hold down PUSH TO TALK when you are not talking. (This is called dead keying.)• Assist callers with directions, information about road conditions, and any other reasonable requests.USING COMMON 10-CODESCB users have adopted the 10-codes for standard questions and answers. This table lists common codes adopted by the Associated Public Safety Communications Officers (APCO).Code Meaning10-1 Your signal is bad. 10-2 Your signal is good.10-3 Stop transmitting.10-4 Message received and understood. 10-5 Relay information to _____.10-6 I am busy or are you busy?10-7 Out of service.10-8  In service.10-9 Repeat last message. 10-10 Negative (NO).10-11 _____ in service. 10-12 Stand by.10-13 Report road/weather conditions.10-14 Information. 21-1706.fm  Page 10  Wednesday, January 9, 2002  8:37 AM
11OperationNote: Although this table lists the 10-codes’ meanings in the form of a statement, they can also be phrased as questions (10-6: Are you busy?, 10-20: What is your location?). MAXIMUM RANGEThe maximum range and quality of CB radio transmissions vary depending on the following conditions:• The type and quality of antenna used• The height of the antenna’s mounting location — the higher the antenna, the better the signal’s range• The surrounding terrain — mountains and tall buildings limit the range• Weather conditions• The number of nearby radios operating on the same channel• Standing wave ratio (SWR) between the antenna and the CB.Note: Your CB radio’s transmission rage is generally line-of -sight.10-15 Message delivered.10-16 Reply to message.10-17 En route.10-18 Urgent.10-19 Contact _____. 10-20 What is your location?10-21 Call _____ by telephone.10-22 Cancel last message.10-23 Arrived at the scene.10-24 Assignment complete.10-25 Meet _____.10-26 Estimated time of arrival is _____.10-30 Use caution.10-31 Pick up.10-33 Emergency traffic. Clear the channel.10-34 What time is it?10-41 Switch to Channel _____.10-62 Cannot understand.Code Meaning21-1706.fm  Page 11  Wednesday, January 9, 2002  8:37 AM
12 TroubleshootingXTroubleshootingIf your CB is not working as it should, follow these suggestions to see if you can eliminate  the problem. If you cannot, take the CB to your local RadioShack store for assistance.Symptom Check/TryCB has trouble receiving. Turn transceiver power on.Microphone connected? Secure connections.Antenna connected? Secure connections.Too much squelch? Adjust as needed.Radio not on operating channel? Switch to an active channel.Be sure PA/MON/CB is set to CB.Adjust VOLUME.Adjust RF GAIN.CB has trouble transmitting. Turn transceiver power on.Antenna connected? Secure connections.All connections free of corrosion? Clean and tighten.Microphone connector loose? Firmly press microphone con-nector into jack.Be sure PA/MON/CB is set to CB.Radio not on operating channel? Switch to an active channel.PUSH TO TALK fully pressed? Press completely.CB does not work at all. Power connected? Secure connections.Microphone connected? Secure connections.Fuse needs replacing? Replace with identical fuse. See “Replacing the Fuse” on Page 13. Cannot select a channel. Be sure PA/MON/CB is set to CB.PUSH TO TALK pressed? Release PUSH TO TALK.PA does not work. Connect a PA speaker. Secure connections.Be sure PA/MON/CB is set to PA.Adjust VOLUME.Sound is distorted. Adjust RF GAIN.Adjust VOLUME.21-1706.fm  Page 12  Wednesday, January 9, 2002  8:37 AM
13TroubleshootingREDUCING NOISEBecause your CB is exceptionally quiet, any noise you hear is probably from an external source in your vehicle such as the alternator, another radio or spark plugs.The transceiver uses an ANL (Automatic Noise Limiter) circuit to reduce noise. However, if possible, try to eliminate noise by finding its source.You can determine the noise’s source by turning off the engine and operating the CB with your vehicle’s ignition set to ACC. If the noise is reduced, the problem is in your vehicle’s ignition or electrical system.Here are a few hints to help you reduce or eliminate such noise:• Make all CB power and antenna wires as short as possible.• Route the power wires away from the antenna wires.• Be sure that the chassis ground connection is secure.• Replace old ignition wires with new, high-voltage, noise suppression wires.• Install noise suppressors on your spark plugs, or install new spark plugs that have built-in noise suppressors.• If problems persist, check your alternator/generator and regulator gauges. You can reduce the noise from these sources by using bypass capacitors at the various output voltage points.Your local RadioShack store has a wide selection of noise suppression accessories.CARETo enjoy your CB for a long time, keep the CB dry. If it gets wet, wipe it dry immediately. Use and store the CB only in normal temperature environments. Handle the CB gently and carefully. Do not drop it. Keep the CB away from dust and dirt. Wipe the CB with a damp cloth occasionally to keep it looking new.Modifying or tampering with the CB’s internal components can cause malfunction and invalidate its warranty and void your FCC authorization to operate it. If your CB is not performing as it should, take it to your local RadioShack store for assistance. REPLACING THE FUSEThe CB’s 2-amp in-line fuse helps protect your CB from power surges and short circuits. When replacement is required, use a 2-amp, slow-blow glass fuse.Caution: Do not use a fuse with ratings other than those specified. Doing so might damage your CB.Follow these steps to replace the fuse.1. Make sure the power source and CB are both off.2. Hold the fuse holder by both ends, push the ends together, twist one end counterclockwise, then pull them apart.3. Remove the old fuse. If it is blown, insert a new one of the same type and rating. If it is not blown, reinsert it.4. Push the fuse holder ends together and twist one end clockwise.21-1706.fm  Page 13  Wednesday, January 9, 2002  8:37 AM
15NotesXNotes21-1706.fm  Page 15  Wednesday, January 9, 2002  8:37 AM
21-1706AO0083AAA11A02Printed in ChinaRadioShack CorporationFort Worth, Texas 76102Limited Ninety-Day WarrantyThis product is warranted by RadioShack against manufacturing defects in material and workman-ship under normal use for ninety (90) days from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDEDHEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIESCONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USEOR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-VISED OF THE POSSIBILITY OF SUCH DAMAGES.Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-tion of incidental or consequential damages, so the above limitations or exclusions may not apply toyou.In the event of a product defect during the warranty period, take the product and the RadioShacksales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-less otherwise provided by law: (a) correct the defect by product repair without charge for parts andlabor; (b) replace the product with one of the same or similar design; or (c) refund the purchaseprice. All replaced parts and products, and products on which a refund is made, become the prop-erty of RadioShack. New or reconditioned parts and products may be used in the performance ofwarranty service. Repaired or replaced parts and products are warranted for the remainder of theoriginal warranty period. You will be charged for repair or replacement of the product made after theexpiration of the warranty period.This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation ormaintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairsother than those provided by a RadioShack Authorized Service Facility; (c) consumables such asfuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costsof product removal, installation, set-up service adjustment or reinstallation.This warranty gives you specific legal rights, and you may also have other rights which vary fromstate to state.RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102We Service What We Sell12/9921-1706.fm  Page 16  Wednesday, January 9, 2002  8:37 AM
53847 CFR Ch. I (10–1–01 Edition)§95.222(3) Tune a receiver to your R/C trans-mitter.(Secs. 4(i) and 303(r), Communications Act of1934, as amended, 47 U.S.C. 154(i) and 303(r),and sec. 553 of the Administrative Proce-dures Act, 5 U.S.C. 553)[48 FR 24890, June 3, 1983, as amended at 49FR 20673, May 16, 1984; 63 FR 36610, July 7,1998]§95.222 (R/C Rule 22) May I make anychanges to my R/C station trans-mitter?(a) You must not make or have any-one else make an internal modificationto your R/C transmitter.(b) Internal modification does not in-clude:(1) Repair or servicing of an R/C sta-tion transmitter (see R/C Rule 21,§95.221); or(2) Changing plug-in modules whichwere certificated as part of your R/Ctransmitter.(c) You must not operate an R/Ctransmitter which has been modifiedby anyone in any way, including modi-fication to operate on unauthorized fre-quencies or with illegal power. (See R/C Rules 9 and 10, §§ 95.209 and 95.210.)[48 FR 24894, June 3, 1983, as amended at 63FR 36610, July 7, 1998]§95.223 (R/C Rule 23) Do I have tomake my R/C station available forinspection?(a) If an authorized FCC representa-tive requests to inspect your R/C sta-tion, you must make your R/C stationand records available for inspection.(b) An R/C station includes all of theradio equipment you use.§95.224 (R/C Rule 24) What are my sta-tion records?Your station records include the fol-lowing documents, as applicable:(a) A copy of each response to an FCCviolation notice or an FCC letter. (SeeR/C Rule 19, §95.219.)(b) Each written permission receivedfrom the FCC. (See R/C Rule 17.)§95.225 (R/C Rule 25) How do I contactthe FCC?(a) FCC National Call Center at 1–888–225–5322.(b) FCC World Wide Web homepage:http://www.fcc.gov.(c) In writing, to FCC, Attention: R/C, 1270 Fairfield Road, Gettysburg, PA17325–7245.[63 FR 68976, Dec. 14, 1998]Subpart D—Citizens Band (CB)Radio ServiceSOURCE: 48 FR 24894, June 3, 1983, unlessotherwise noted.GENERALPROVISIONS§95.401 (CB Rule 1) What are the Citi-zens Band Radio Services?The Citizens Band Radio Servicesare:(a) The Citizens Band (CB) RadioService—a private, two-way, short-dis-tance voice communications service forpersonal or business activities of thegeneral public. The CB Radio Servicemay also be used for voice paging.(b) The Family Radio Service(FRS)—a private, two-way, very short-distance voice communications servicefor facilitating family and group ac-tivities. The rules for this service arecontained in subpart B of this part.(c) The Low Power Radio Service(LPRS)—a private, short-distance com-munication service providing auditoryassistance to persons with disabilities,persons who require language trans-lation, and persons in educational set-tings, health care assistance to the ill,law enforcement tracking services incooperation with law enforcement, andpoint-to-point network control commu-nications for Automated Marine Tele-communications System (AMTS) coaststations licensed under part 80 of thischapter. The rules for this service arelisted under subpart G of this part.Two-way voice communications areprohibited.(d) The Medical Implant Communica-tions Service (MICS)—an ultra-lowpower radio service for the trans-mission of non-voice data for the pur-pose of facilitating diagnostic and/ortherapeutic functions involving im-planted medical devices. The rules forthis service are contained in subpart Iof this part.(e) The Wireless Medical TelemetryService (WMTS)—a private, short dis-tance data communication service forVerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00538 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
539Federal Communications Commission §95.405the transmission of patient medical in-formation to a central monitoring lo-cation in a hospital or other medicalfacility. Voice and video communica-tions are prohibited. Waveforms suchas electrocardiograms (ECGs) are notconsidered video. The rules for thisservice are contained in subpart H ofthis part.(f) The Multi-Use Radio Service(MURS)—a private, two-way, short-dis-tance voice, data or image communica-tions service for personal or businessactivities of the general public. Therules for this service are contained insubpart J of this part.[61 FR 28769, June 6, 1996, as amended at 61FR 46566, Sept. 4, 1996; 64 FR 69929, Dec. 15,1999; 65 FR 44008, July 17, 2000; 65 FR 53190,Sept. 1, 2000; 65 FR 60877, Oct. 13, 2000]§95.402 (CB Rule 2) How do I usethese rules?(a) You must comply with these rules(See CB Rule 21 §95.421, for the pen-alties for violations) when you operatea station in the CB Service from:(1) Within or over the territorial lim-its of places where radio services areregulated by the FCC (see CB Rule 5,§95.405);(2) Aboard any vessel or aircraft reg-istered in the United States; or(3) Aboard any unregistered vessel oraircraft owned or operated by a UnitedStates citizen or company.(b) Your CB station must complywith technical rules found in subpart Eof part 95.(c) Where the rules use the word‘‘you’’,  ‘‘you’’ means a person oper-ating a CB station.(d) Where the rules use the word‘‘person,’’ the rules are concerned withan individual, a corporation, a partner-ship, an association, a joint stock com-pany, a trust, a state, territorial orlocal government unit, or other legalentity.(e) Where the rules use the term‘‘FCC’’, that means the Federal Com-munications Commission.(f) Where the rules use the term ‘‘CBstation’’, that means a radio stationtransmitting in the CB Radio Service.§95.403 (CB Rule 3) Am I eligible tooperate a CB station?You are authorized to operate a CBstation unless:(a) You are a foreign government, arepresentative of a foreign govern-ment, or a federal government agency;or(b) The FCC has issued a cease anddesist order to you, and the order isstill in effect.§95.404 (CB Rule 4) Do I need a li-cense?You do not need an individual licenseto operate a CB station. You are au-thorized by this rule to operate yourCB station in accordance with the rulesin this subpart.§95.405 (CB Rule 5) Where may I oper-ate my CB station?You are authorized to operate yourCB station from:(a) Within or over any area of theworld where radio services are regu-lated by the FCC. Those areas are with-in the territorial limits of:(1) The fifty United States.(2) The District of Columbia.Caribbean Insular areas(3) Commonwealth of Puerto Rico.(4) Navassa Island.(5) United States Virgin Islands (50islets and cays).Pacific Insular areas(6) American Samoa (seven islands).(7) Baker Island.(8) Commonwealth of Northern Mar-iana Islands.(9) Guam Island.(10) Howland Island.(11) Jarvis Island.(12) Johnston Island (Islets East,Johnston, North and Sand).(13) Kingman Reef.(14) Midway Island (Islets Easternand Sand).(15) Palmyra Island (more than 50 is-lets).(16) Wake Island (Islets Peale, Wakeand Wilkes).(b) Any other area of the world, ex-cept within the territorial limits ofareas where radio services are regu-lated by—VerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00539 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
54047 CFR Ch. I (10–1–01 Edition)§ 95.406(1) An agency of the United Statesother than the FCC. (You are subjectto its rules.)(2) Any foreign government. (You aresubject to its rules.)(c) An aircraft or ship, with the per-mission of the captain, within or overany area of the world where radio serv-ices are regulated by the FCC or uponor over international waters. You mustoperate your CB station according toany applicable treaty to which theUnited States is a party.(d) Anyone intending to operate a CBstation on the islands of Puerto Rico,Desecheo, Mona, Vieques, and Culebrain a manner that could pose an inter-ference threat to the Arecibo Observ-atory shall notify the Interference Of-fice, Arecibo Observatory, Post OfficeBox 995, Arecibo, Puerto Rico 00613, inwriting or electronically, of the loca-tion of the unit. Operators may wish toconsult interference guidelines, whichwill be provided by Cornell University.Operators who choose to transmit in-formation electronically should e-mailto: prcz@naic.edu.(1) The notification to the Inter-ference Office, Arecibo Observatoryshall be made 45 days prior to com-mencing operation of the unit. The no-tification shall state the geographicalcoordinates of the unit.(2) After receipt of such notifications,the Commission will allow the AreciboObservatory a period of 20 days forcomments or objections. The operatorwill be required to make reasonable ef-forts in order to resolve or mitigateany potential interference problemwith the Arecibo Observatory. If theCommission determines that an oper-ator has satisfied its responsibility tomake reasonable efforts to protect theObservatory from interference, theunit may be allowed to operate.[48 FR 24894, June 3, 1983, as amended at 62FR 55535, Oct. 27, 1997]§95.406 (CB Rule 6) Are there any spe-cial restrictions on the location ofmy CB station?(a) If your CB station is located onpremises controlled by the Departmentof Defense you may be required to com-ply with additional regulations im-posed by the commanding officer of theinstallation.(b) If your C/B station will be con-structed on an environmentally sen-sitive site, or will be operated in sucha manner as to raise environmentalproblems, under §1.1307 of this chapter,you must provide an environmental as-sessment, as set forth in §1.1311 of thischapter, and undergo the environ-mental review, §1.1312 of this chapter,before commencement of construction.[48 FR 24894, June 3, 1983, as amended at 55FR 20398, May 16, 1990]HOWTOOPERATE ACB STATION§95.407 (CB Rule 7) On what channelsmay I operate?(a) Your CB station may transmitonly on the following channels (fre-quencies):Channel Frequency(megahertz—MHz)1 ...................................................................... 26.9652 ...................................................................... 26.9753 ...................................................................... 26.9854 ...................................................................... 27.0055 ...................................................................... 27.0156 ...................................................................... 27.0257 ...................................................................... 27.0358...................................................................... 27.0559......................................................................127.06510 .................................................................... 27.07511 .................................................................... 27.08512 .................................................................... 27.10513 .................................................................... 27.11514 .................................................................... 27.12515 .................................................................... 27.13516 .................................................................... 27.15517 .................................................................... 27.16518 .................................................................... 27.17519 .................................................................... 27.18520 .................................................................... 27.20521 .................................................................... 27.21522 .................................................................... 27.22523 .................................................................... 27.25524 .................................................................... 27.23525 .................................................................... 27.24526 .................................................................... 27.26527 .................................................................... 27.27528 .................................................................... 27.28529 .................................................................... 27.29530 .................................................................... 27.30531 .................................................................... 27.31532 .................................................................... 27.32533 .................................................................... 27.33534 .................................................................... 27.34535 .................................................................... 27.35536 .................................................................... 27.36537 .................................................................... 27.37538 .................................................................... 27.38539 .................................................................... 27.39540 .................................................................... 27.4051See paragraph (b) of this section.(b) Channel 9 may be used only foremergency communications or fortraveler assistance.VerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00540 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
541Federal Communications Commission § 95.411(c) You must, at all times and on allchannels, give priority to emergencycommunication messages concerningthe immediate safety of life or the im-mediate protection of property.(d) You may use any channel foremergency communications or fortraveler assistance.(e) You must share each channel withother users.(f) The FCC will not assign any chan-nel for the private or exclusive use ofany particular CB station or group ofstations.(g) The FCC will not assign any chan-nel for the private of exclusive use ofCB stations transmitting single side-band or AM.§95.408 (CB Rule 8) How high may Iput my antenna?(a) Antenna  means the radiating sys-tem (for transmitting, receiving orboth) and the structure holding it up(tower, pole or mast). It also means ev-erything else attached to the radiatingsystem and the structure.(b) If your antenna is mounted on ahand-held portable unit, none of thefollowing limitations apply.(c) If your antenna is installed at afixed location, it (whether receiving,transmitting or both) must complywith either one of the following:(1) The highest point must not bemore than 6.10 meters (20 feet) higherthan the highest point of the buildingor tree on which it is mounted; or(2) The highest point must not bemore than 18.3 meters (60 feet) abovethe ground.(d) If your CB station is located nearan airport, and if you antenna struc-ture is more than 6.1 meters (20 feet)high, you may have to obey additionalrestrictions. The highest point of yourantenna must not exceed one meterabove the airport elevation for everyhundred meters of distance from thenearest point of the nearest airportrunway. Differences in ground ele-vation between your antenna and theairport runway may complicate thisformula. If your CB station is near anairport, you may contact the nearestFCC field office for a worksheet to helpyou figure the maximum allowableheight of your antenna. Consult part 17of the FCC’s Rules for more informa-tion.WARNING: Installation and removal of CBstation antennas near powerlines is dan-gerous. For your safety, follow the installa-tion directions included with your antenna.[48 FR 24894, June 3, 1983, as amended at 48FR 41416, Sept. 15, 1983]§95.409 (CB Rule 9) What equipmentmay I use at my CB station?(a) You must use an FCC certificatedCB transmitter at your CB station.You can identify an FCC certificatedtransmitter by the certification labelplaced on it by the manufacturer. Youmay examine a list of certificatedequipment at any FCC Field Office orat FCC Headquarters. Use of a trans-mitter which is not FCC certificatedvoids your authority to operate thestation.(b) You must not make, or havemade, any internal modification to acertificated CB transmitter. (See CBRule 25, §95.425). Any internal modi-fication to a certificated CB trans-mitter cancels the certification, anduse of such a transmitter voids yourauthority to operate the station.[48 FR 24894, June 3, 1983, as amended at 63FR 36610, July 7, 1998]§95.410 (CB Rule 10) How much powermay I use?(a) Your CB station transmitterpower output must not exceed the fol-lowing values under any conditions:AM (A3)—4 watts (carrier power) SSB—12watts (peak envelope power)(b) If you need more informationabout the power rule, see the technicalrules in subpart E of part 95.(c) Use of a transmitter which hascarrier or peak envelope power in ex-cess of that authorized voids your au-thority to operate the station.§95.411 (CB Rule 11) May I use poweramplifiers?(a) You may not attach the followingitems (power amplifiers) to your cer-tificated CB transmitter in any way:(1) External radio frequency (RF)power amplifiers (sometimes calledlinears or linear amplifiers); orVerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00541 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
54247 CFR Ch. I (10–1–01 Edition)§ 95.412(2) Any other devices which, whenused with a radio transmitter as a sig-nal source, are capable of amplifyingthe signal.(b) There are no exceptions to thisrule and use of a power amplifier voidsyour authority to operate the station.(c) The FCC will presume you haveused a linear or other external RFpower amplifier if—(1) It is in your possession or on yourpremises; and(2) There is other evidence that youhave operated your CB station withmore power than allowed by CB Rule10, §95.410.(d) Paragraph (c) of this section doesnot apply if you hold a license in an-other radio service which allows you tooperate an external RF power ampli-fier.[48 FR 24894, June 3, 1983, as amended at 63FR 36610, July 7, 1998]§95.412 (CB Rule 12) What commu-nications may be transmitted?(a) You may use your CB station totransmit two-way plain language com-munications. Two-way plain languagecommunications are communicationswithout codes or coded messages. Oper-ating signals such as ‘‘ten codes’’ arenot considered codes or coded mes-sages. You may transmit two-wayplain language communications onlyto other CB stations, to units of yourown CB station or to authorized gov-ernment stations on CB frequenciesabout—(1) Your personal or business activi-ties or those of members of your imme-diate family living in your household;(2) Emergencies (see CB Rule 18,§95.418);(3) Traveler assistance (see CB Rule18, §95.418); or(4) Civil defense activities in connec-tion with official tests or drills con-ducted by, or actual emergencies an-nounced by, the civil defense agencywith authority over the area in whichyour station is located.(b) You may use your CB station totransmit a tone signal only when thesignal is used to make contact or tocontinue communications. (Examplesof circuits using these signals are toneoperated squelch and selective callingcircuits.) If the signal is an audibletone, it must last no longer than 15seconds at one time. If the signal is asubaudible tone, it may be transmittedcontinuously only as long as you aretalking.(c) You may use your CB station totransmit one-way communications(messages which are not intended to es-tablish communications between twoor more particular CB stations) onlyfor emergency communications, trav-eler assistance, brief tests (radiochecks) or voice paging.§95.413 (CB Rule 13) What commu-nications are prohibited?(a) You must not use a CB station—(1) In connection with any activitywhich is against federal, state or locallaw;(2) To transmit obscence, indecent orprofane words, language or meaning;(3) To interfere intentionally withthe communications of another CB sta-tion;(4) To transmit one-way communica-tions, except for emergency commu-nications, traveler assistance, brieftests (radio checks), or voice paging;(5) To advertise or solicit the sale ofany goods or services;(6) To transmit music, whistling,sound effects or any material to amuseor entertain;(7) To transmit any sound effect sole-ly to attract attention;(8) To transmit the word ‘‘MAYDAY’’or any other international distress sig-nal, except when your station is lo-cated in a ship, aircraft or other vehi-cle which is threatened by grave andimminent danger and your are request-ing immediate assistance;(9) To communicate with, or attemptto communicate with, any CB stationmore than 250 kilometers (155.3 miles)away;(10) To advertise a political candidateor political campaign; (you may useyour CB radio for the business or orga-nizational aspects of a campaign, if youfollow all other applicable rules);(11) To communicate with stations inother countries, except General RadioService stations in Canada; or(12) To transmit a false or deceptivecommunication.(b) You must not use a CB station totransmit communications for live orVerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00542 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
543Federal Communications Commission § 95.419delayed rebroadcast on a radio or tele-vision broadcast station. You may useyour CB station to gather news itemsor to prepare programs.§95.414 (CB Rule 14) May I be paid touse my CB station?(a) You may not accept direct or in-direct payment for transmitting with aCB station.(b) You may use a CB station to helpyou provide a service, and be paid forthat service, as long as you are paidonly for the service and not for the ac-tual use of the CB station.§95.415 (CB Rule 15) Who is respon-sible for communications I make?You are responsible for all commu-nications which are made by you froma CB station.§95.416 (CB Rule 16) Do I have to limitthe length of my communications?(a) You must limit your CB commu-nications to the minimum practicaltime.(b) If you are communicating withanother CB station or stations, you,and the stations communicating withyou, must limit each of your conversa-tions to no more than five continuousminutes.(c) At the end of your conversation,you, and the stations communicatingwith you, must not transmit again forat least one minute.§95.417 (CB Rule 17) Do I identify myCB communications?(a) You need not identify your CBcommunications.(b) [You are encouraged to identifyyour CB communications by any of thefollowing means:(1) Previously assigned CB call sign;(2) K prefix followed by operator ini-tials and residence zip code;(3) Name; or(4) Organizational description includ-ing name and any applicable operatorunit number.](c) [You are encouraged to use your‘‘handle’’ only in conjuction with themethods of identification listed inparagraph (b) of this section.]§95.418 (CB Rule 18) How do I use myCB station in an emergency or toassist a traveler?(a) You must at all times and on allchannels, give priority to emergencycommunications.(b) When you are directly partici-pating in emergency communications,you do not have to comply with therule about length of transmissions (CBRule 16, §95.416). You must obey allother rules.(c) You may use your CB station forcommunications necessary to assist atraveler to reach a destination or to re-ceive necessary services. When you areusing your CB station to assist a trav-eler, you do not have to obey the ruleabout length of transmissions (CB Rule16,  §95.416). You must obey all otherrules.(d) You may use your CB station totransmit one-way communicationsconcerning highway conditions to as-sist travelers.[48 FR 24894, June 3, 1983, as amended at 57FR 22442, May 28, 1992]§95.419 (CB Rule 19) May I operate myCB station transmitter by remotecontrol?(a) You may not operate a CB stationtransmitter by radio remote control.(b) You may operate a CB trans-mitter by wireline remote control ifyou obtain specific approval in writingfrom the FCC. To obtain FCC approval,you must show why you need to oper-ate your station by wireline remotecontrol. If you receive FCC approval,you must keep the approval as part ofyour station records. See  CB Rule 27,§95.427.(c) Remote control means operationof a CB transmitter from any placeother than the location of the CBtransmitter. Direct mechanical controlor direct electrical control by wirefrom some point on the same premises,craft or vehicle as the CB transmitteris not considered remote control.[48 FR 24894, June 3, 1983, as amended at 57FR 40343, Sept. 3, 1992; 63 FR 68976, Dec. 14,1998]VerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00543 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
54447 CFR Ch. I (10–1–01 Edition)§ 95.420§95.420 (CB Rule 20) May I connectmy CB station transmitter to a tele-phone?(a) You may connect your CB stationtransmitter to a telephone if you com-ply with all of the following:(1) You or someone else must bepresent at your CB station and must—(i) Manually make the connection(the connection must not be made byremote control);(ii) Supervise the operation of thetransmitter during the connection;(iii) Listen to each communicationduring the connection; and(iv) Stop all communications if thereare operations in violation of theserules.(2) Each communication during thetelephone connection must complywith all of these rules.(3) You must obey any restrictionthat the telephone company places onthe connection of a CB transmitter toa telephone.(b) The CB transmitter you connectto a telephone must not be shared withany other CB station.(c) If you connect your CB trans-mitter to a telephone, you must use aphone patch device with has been reg-istered with the FCC.OTHERTHINGSYOUNEEDTOKNOW§95.421 (CB Rule 21) What are thepenalties for violating these rules?(a) If the FCC finds that you havewillfully or repeatedly violated theCommunications Act or the FCC Rules,you may have to pay as much as $10,000for each violation, up to a total of$75,000. (See section 503(b) of the Com-munications Act.)(b) If the FCC finds that you haveviolated any section of the Commu-nications Act or the FCC Rules, youmay be ordered to stop whatever actioncaused the violation. (See section312(b) of the Communications Act.)(c) If a Federal court finds that youhave willfully and knowingly violatedany FCC Rule, you may be fined up to$500 for each day you committed theviolation. (See section 502 of the Com-munications Act.)(d) If a Federal court finds that youhave willfully and knowingly violatedany provision of the CommunicationsAct, you may be fined up to $10,000 oryou may be imprisoned for one year, orboth. (See section 501 of the Commu-nications Act.)[48 FR 24894, June 3, 1983, as amended at 57FR 40343, Sept. 3, 1992]§95.422 (CB Rule 22) How do I answercorrespondence from the FCC?(a) If it appears to the FCC that youhave violated the Communications Actor these rules, the FCC may send you adiscrepancy notice.(b) Within the time period stated inthe notice, you must answer with:(1) A complete written statementabout the apparent discrepancy;(2) A complete written statementabout any action you have taken tocorrect the apparent violation and toprevent it from happening again; and(3) The name of the person operatingat the time of the apparent violation.(c) If the FCC sends you a letter ask-ing you questions about your CB radiostation or its operation, you must an-swer each of the questions with a com-plete written statement within thetime period stated in the letter.(d) You must not shorten your an-swer by references to other commu-nications or notices.(e) You must send your answer to theFCC office which sent you the notice.(f) You must keep a copy of your an-swer in your station records. (See CBRule 27, §95.427.)§95.423 (CB Rule 23) What must I do ifthe FCC tells me that my CB stationis causing interference?(a) If the FCC tells you that your CBstation is causing interference for tech-nical reasons you must follow all in-structions in the official FCC notice.(This notice may require you to havetechnical adjustments made to yourequipment.)(b) You must comply with any re-stricted hours of CB station operationwhich may be included in the officialnotice.§95.424 (CB Rule 24) How do I havemy CB station transmitter serviced?(a) You may adjust an antenna toyour CB transmitter and you maymake radio checks. (A radio checkmeans a one way transmission for aVerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00544 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T
545Federal Communications Commission § 95.601short time in order to test the trans-mitter.)(b) You are responsible for the properoperation of the station at all timesand are expected to provide for obser-vations, servicing and maintenance asoften as may be necessary to ensureproper operation. You must have all in-ternal repairs or internal adjustmentsto your CB transmitter made in ac-cordance with the Technical Regula-tions (see subpart E). The internal re-pairs or internal adjustments should beperformed by or under the immediatesupervision and responsibility of a per-son certified as technically qualified toperform transmitter maintenance andrepair duties in the private land mobileservices and fixed services by an orga-nization or committee representativeof users in those services.(c) Except as provided in paragraph(d) of this section, each internal repairand each internal adjustment of a CBtransmitter in which signals are trans-mitted must be made using a nonradi-ating (‘‘dummy’’) antenna.(d) Brief test signals (signals notlonger than one minute during any fiveminute period) using a radiating an-tenna may be transmitted in order to:(1) Adjust an antenna to a trans-mitter;(2) Detect or measure radiation of en-ergy other than the intended signal; or(3) Tune a receiver to your CB trans-mitter.(Secs. 4(i) and 303(r), Communications Act of1934, as amended, 47 U.S.C. 154(i) and 303(r),and sec. 553 of the Administrative Proce-dures Act, 5 U.S.C. 553)[48 FR 24894, June 3, 1983, as amended at 49FR 20673, May 16, 1984]§95.425 (CB Rule 25) May I make anychanges to my CB station trans-mitter?(a) You must not make or have anyone else make any internal modifica-tion to your CB transmitter.(b) Internal modification does not in-clude:(1) Repair or servicing of a CB stationtransmitter (see CB Rule 24, §95.424); or(2) Changing plug-in modules whichwere certificated as part of your CBtransmitter.(c) You must not operate a CB trans-mitter which has been modified by any-one in any way, including modificationto operate on unauthorized frequenciesor with illegal power. (See CB Rules 9and 11, §§ 95.409 and 95.411.)[48 FR 24894, June 3, 1983, as amended at 63FR 36610, July 7, 1998]§95.426 (CB Rule 26) Do I have tomake my CB station available forinspection?(a) If an authorized FCC representa-tive requests to inspect your CB sta-tion, you must make your CB stationand records available for inspection.(b) A CB station includes all of theradio equipment you use.§95.427 (CB Rule 27) What are my sta-tion records?Your station records include the fol-lowing documents, as applicable.(a) A copy of each response to an FCCviolation notice or an FCC letter. (SeeCB Rule 22, §95.422.)(b) Each written permission receivedfrom the FCC. (See CB Rule 19, §95.419.)§95.428 (CB Rule 28) How do I contactthe FCC?(a) FCC National Call Center at 1–888–225–5322.(b) FCC World Wide Web homepage:http://www.fcc.gov.(c) In writing, to FCC, Attention: CB,1270 Fairfield Road, Gettysburg, PA17325–7245.[63 FR 68976, Dec. 14, 1998]Subpart E—Technical RegulationsSOURCE: 53 FR 36789, Sept. 22, 1988, unlessotherwise noted.GENERALPROVISIONS§95.601 Basis and purpose.This section provides the technicalstandards to which each transmitter (ap-paratus that converts electrical energyreceived from a source into RF (radiofrequency) energy capable of being ra-diated) used or intended to be used in astation authorized in any of the Per-sonal Radio Services must comply.This section also provides require-ments for obtaining certification forsuch transmitters. The Personal RadioVerDate 11<MAY>2000 09:08 Oct 16, 2001 Jkt 194192 PO 00000 Frm 00545 Fmt 8010 Sfmt 8010 Y:\SGML\194192T.XXX pfrm04 PsN: 194192T

Navigation menu