Ruckus Wireless Q7000400 SmartCell Q700 Access Point User Manual

Ruckus Wireless, Inc. SmartCell Q700 Access Point

a href="https://usermanual.wiki/Ruckus-Wireless" itemprop="url"> Ruckus Wireless >

User Manual

SmartCell™ Q700Quick Setup GuideThis Quick Setup Guide provides step-by-step instructions on how to set up your Ruckus SmartCell™ Q700 Access Point (AP). After completing the steps described in this Guide, you will be able to place the Q700 at your site and provide LTE wireless network access to users.Figure 1. Ruckus SmartCell™ Q700 Access PointBefore You BeginBefore deploying Ruckus Wireless products, please check for the latest information and release documentation athttp://support.ruckuswireless.com/documentsSoftware License and Limited Warranty are available athttp://support.ruckuswireless.com/warrantyPackage ContentsCheck the package contents as follows:• SmartCell Q700 Access Point• Mounting Bracket• 4 Bracket Screws (Phillips #2)• 2 Wall Mounting Screws (Phillips #2)• 2 Wall Anchors• US AC/DC Adapter (Q700-0200 and Q700-0400 models only)• EUR AC/DC Adapter (Q700-0300 and Q700-0700 models only)• UK AC/DC Adapter (Q700-0300 and Q700-0700 models only)• Product warranty statement• This SmartCell Q700 Quick Setup GuideMounting InstructionsThe AP can be mounted to a drop-ceiling T-bar or flat surface.Mounting on a Drop-Ceiling T-BarThe factory-supplied mounting bracket allows you to attach the AP to drop-ceiling T-bars.Figure 2. AP Mounting Bracket1) If not attached already, attach the bracket to the AP at [A] using the included Bracket Screws.2) Lift the AP with the bracket facing the drop-ceiling and position the Studs [B] on the bracket slightly offset from either side of the T-bar.3) Gently turn the AP clockwise until the Studs slip over the T-bar and both Clasps [C] snap in place against the T-bar.Figure 3. AP securely attached to T-barNote: In order to properly support its weight, make sure that the AP is mounted at the intersection of two rails and not along a single rail!4) To un-mount the AP, simply press down on the two Clasps [C] and gently turn the AP counter-clockwise until it comes off.Mounting on a Flat SurfaceThe factory-supplied mounting screws and plastic wall anchors allow you to attach the AP to a wall or ceiling.1) Attach the bracket to the AP using the included Bracket Screws.2) Use the Mounting Template on the last page of this Quick Setup Guide to mark the locations for two drill holes on the mounting surface.3) Use a 4.75mm (3/16”) drill bit to drill holes approximately 25mm (1”) deep into the mounting surface.4) Insert the factory-supplied anchors and mounting screws into the mounting surface, leaving approximately 6 mm (1/4”) of the screw heads protruding for the AP bracket.5) Place the AP and bracket onto the mounting screws so that the screw heads enter the Keyholes [D] on the AP bracket and gently push down.Making the ConnectionsBe sure to use a Cat 5e or better Ethernet cable with non-booted connectors (see Figure 4). If using PoE, attach one of the Ethernet cable to an 802.3at Type 2-certified switch or PoE injector (sold separately). Attach the other end of the Ethernet cable to the leftmost Ethernet port [E] on the AP as shown in Figure 5. If using an AC/DC adapter, connect it to the power port [F] in Figure 5 and to an electrical outlet.Figure 4. Non-booted Ethernet connectorFigure 5. Port locationsCheck the LED LightsOnce connected, the AP will power on and automatically connect to the Ruckus Cloud over the Internet to configure itself. You will see some activity and after 2-5 minutes all lights should turn solid Green or solid Amber. If any light is off or flashing, see the following table for troubleshooting: PWR Check Power, Ethernet connections and PoE switchEMS Check Internet connection and network settingsEPC Check Internet connection and network settingsSYNC Make sure one of the APs in the network is near a windowLTE Use the Ruckus Cloud for additional guidanceFor More InformationThe AP is now operational and can be further managed by the Ruckus Cloud service. For more information refer to the appropriate Ruckus Wireless Cloud documentation or visithttp://support.ruckuswireless.comAAAABBCCDDDDEFCopyright © 2015 Ruckus Wireless, Inc.Published 17 November 2015, Part Number 800-71074-001 Rev B
Wall Mounting Template(All dimensions in mm)Copyright © 2015 Ruckus Wireless, Inc.Published 17 November 2015, Part Number 800-71074-001 Rev B
Download:
Mirror Download [FCC.gov]
Document ID3205061
Application IDiN6AAb82t0TUbZjIo/1U6Q==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.87kB (210897 bits)
Date Submitted2016-11-23 00:00:00
Date Available2017-05-27 00:00:00
Creation Date2016-11-17 19:14:38
Producing SoftwareAdobe Acrobat Standard DC 15.6.30244
Document Lastmod2016-11-17 19:38:52
Document TitleUser Manual
Document CreatorAdobe Acrobat Standard DC 15.6.30244
FCC ID Filing: S9GQ7000400

Navigation menu