Ruckus Wireless R300 IEEE 802.11 a/b/g/n Access Point User Manual
Ruckus Wireless, Inc. IEEE 802.11 a/b/g/n Access Point Ruckus Wireless AP ZF2942 7942 Quick Setup Guide
a href="https://usermanual.wiki/Ruckus-Wireless" itemprop="url">
Ruckus Wireless >
Users Manual
![Copyright © 2013 Ruckus Wireless, Inc.Published June 2013, Part Number 800-70507-001 Rev BMOUNTING TEMPLATEmm3Press <Enter> to initiate the connection. When a security alert dialog box appears, click OK/Yes to proceed.4When the Ruckus Wireless Admin login page appears, enter the following: •Username: super•Password: sp-admin5Click Login.STEP 4: CUSTOMIZE THE WIRELESS SETTINGS1On the Web interface menu, click Configuration > Wire-less [2.4G/5G]. The Configure :: Wireless :: Common options appear. 2Verify that the following options are active:•Channel: SmartSelect•Country Code: If you are not located in the United States, select your current country. 3Click Update Settings if you made any changes.4Click any of the eight “Wireless #” tabs at the top of the page. 5In Wireless Availability, click Enabled.6Delete the text in the SSID field, and then type a name for your network that will help your users identify the AP in their wireless network connection application.7Click Update Settings to save your changes.8Repeat Steps 4-7 for each Wireless # interface that you want to enable. 9Click Logout to exit the Web interface.10 Disconnect the AP from the computer and from the current power source, and then restore your computer to its original network connection configuration. STEP 5: PLACE THE AP IN YOUR SITE 1Move the AP to its permanent location (accessible to both AC power and network connection). 2Use an Ethernet cable to connect the 10/100/1000 port of the AP to your network.3Connect the AC power adapter (or PoE power supply) to the AP, then to a convenient power source.4Verify that the 10/100/1000 port LED is lit.STEP 6: VERIFY THE INSTALLATION1Using any wireless-enabled computer or mobile device, search for and select the wireless network you previously configured. 2If you can connect, open a browser and link to any public Web site.Congratulations! Your wireless network is active and ready for use. If you need to configure advanced wireless settings, such as enabling security, see the ZoneFlex AP User Guide.(OPTIONAL) MOUNTING INSTRUCTIONSThe ZoneFlex R300 can be mounted to a wall, ceiling or to a T-bar using the supplied mounting screws or the T-bar clips built into the bottom of the AP enclosure. Mounting to a Flat Surface1Use this Quick Start Guide template to mark the locations for screw holes on the mounting surface. Use a 5mm drill bit to drill approximately 25mm into the mounting surface. 2Insert the anchors and mounting screws into the mounting surface, leaving approximately 1/4” (6 mm) of the screw heads protruding for the AP enclosure. The screws should be approximately 3.25” (82.6mm) apart per the template.3Insert the pin removal tool into the hole on the side of the AP (Figure 1.), to release the locking mechanism. Figure 1. Insert the pin removal tool into the pinhole4Place the AP onto the mounting screws so that the screw heads enter the mounting holes on the AP enclosure, and push the AP (to the left or down depending on orientation) to lock in place. 5Remove the pin removal tool to release the lock mechanism and secure the AP.6To unmount, insert the pin removal tool into the hole on the side of the AP to unlock, then push the AP (to the right or up, depending on orientation) to release the AP enclosure from the mounting screws. Mounting to a T-Bar1Orient the AP so that the T-bar is positioned between the T-bar clips as shown in Figure 2., then rotate the AP until the third T-bar clip catches the T-bar and the latch locks the T-bar in place (Figure 3.). Figure 2.Figure 3.2For added physical security, use a Torx screwdriver to insert the security screw into the hole shown in Figure 3. 3To remove the unit, first remove the security screw, then depress the latch while rotating the AP so that the T-bar clips disengage the T-bar. FOR MORE INFORMATIONFor information on how to configure the AP from the Web interface, refer to the Ruckus Wireless ZoneFlex Access Point User Guide or the Online Help, available from within the Web interface. NOTE: If you will be using PoE, you will need a Cat 5e (or better) Ethernet cable to connect the AP to the PoE injec-tor or switch.Hold pin removal toolin while mountingSecurity screw hole](https://usermanual.wiki/Ruckus-Wireless/R300/User-Guide-2044179-Page-2.png)