Ruckus Wireless T300 IEEE 802.11ac Access Point User Manual

Ruckus Wireless, Inc. IEEE 802.11ac Access Point

a href="https://usermanual.wiki/Ruckus-Wireless" itemprop="url"> Ruckus Wireless >

Contents

User Manual

Copyright © 2014 Ruckus Wireless, Inc.Published May 2014, Part Number 800-70492-001 Rev A Page 1 of 4T300 Access PointMounting GuideThis Mounting Guide provides step-by-step instructions on how to field-install the Ruckus Wireless T300 Omni 802.11ac outdoor access point (AP). Unless specifically indicated, the rest of this document refers to the T300 as an AP.For detailed information on planning the installation, performing a site survey, preparing the AP at the depot and shipping to the field, refer to the T300, T301n and T301s 802.11ac Outdoor Access Point Installation Guide. For information on configuring and operating the AP, refer to the ZoneFlex Outdoor Access Point User Guide. Both documents are available at https://support.ruckuswireless.com.WARNING: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. WARNING: Installation of this equipment must comply with local and national electrical codes. CAUTION: Make sure that you form a 80mm - 130mm (3”-5”) drip loop in any cable that is attached to the AP or the building. This will prevent water from running along the cable and entering the AP or the building where the cable terminates. CAUTION: Be sure that grounding is available and that it meets local and national electrical codes. For additional lightning protection, use lightning rods and lightning arrestors. CAUTION: Make sure that proper lightning surge protection precautions are taken according to local electrical code. WARNING: Ruckus Wireless strongly recommends that you wear eye protection before mounting the AP.BEFORE YOU BEGINBefore deploying Ruckus Wireless products, please check for the latest software and the release documentation.• User Guides and Release Notes are available athttp://support.ruckuswireless.com/documents• Software Upgrades are available athttp://support.ruckuswireless.com/software• Open Source information is available athttp://opensource.ruckuswireless.com• Software License and Limited Warranty available athttp://support.ruckuswireless.com/warrantyREQUIRED HARDWARE AND TOOLS• Torque wrench or torque screwdriver with sockets and bits• Wide flat-blade screwdriverIf you are mounting the AP on a flat surface, then you will also need:• Customer-supplied wall anchors rated to withstand 128 N or 28.8 lbf (required to withstand wind loads of 266km/h or 165mph)• Electric drill with drill bits and customer-supplied wall anchors, flat washers, and hex nuts for flat-surface mountIf you are mounting the AP on a pipe or pole, then you will also need:• A 30mm to 60mm (1.18" to 2.36") pipe or pole• Two factory-supplied steel clampsPACKAGE CONTENTSBefore deploying your AP in the field, verify that all items listed below are included in the package. If any item is damaged or missing, notify your authorized Ruckus Wireless sales representative. Also, make sure that you have the required hardware and tools. • One T300 AP (A in Figure 1); includes one wall- or pole-mounting bracket and one 12mm M6x1 earth ground screw with split lock and flat washers• One M25 data cable gland (B in Figure 1)• One green/yellow earth ground wire with ring terminal (C in Figure 1)• Two SAE32-sized stainless steel clamps, 2.5-inch diameter (D in Figure 1)Figure 1: AP field-installation package contentsThe field installation package can also include: • Service Level Agreement/Limited Warranty Statement• Regulatory Statement• Registration card• Declaration of Conformity, if required•This Mounting Guide CAUTION! The minimum software revision for the T300 AP is ZoneFlex (ZF) 9.8.1, or SmartCell Gateway (SCG) 2.5.1 or later.Do not connect the T300 AP to a Ruckus Wireless Controller with ZF 9.8.0 or earlier, or to SCG 2.5.0 or earlier.A CB D
Copyright © 2014 Ruckus Wireless, Inc.Published May 2014, Part Number 800-70492-001 Rev A Page 2 of 4T300 OMNI ANTENNA COVERAGEThe T300 AP (ordering part number 901-T300-xx-01) is best deployed where internal-antenna lateral beamforming can provide the greatest reach and throughput to a wide coverage area, or to provide the greatest distance between APs in a connecting mesh device. See Figure 2 for the side view coverage pattern, see Figure 3 for the top view coverage pattern, and see Figure 4 for a typical mesh coverage pattern.Figure 2: AP omni coverage, side viewFigure 3: AP omni coverage, top viewFigure 4: AP mesh elevation plane coverage, side viewSTEP 1: CONNECTING AND SEALING THE RJ-45 CABLEThe AP uses one RJ-45 cable for Power over Ethernet (PoE). Connect and seal the cable using the M25 data cable gland (B in Figure 1).1Feed the end of the RJ-45 cable through the sealing nut (D in Figure 5), rubber sealing insert (C in Figure 5), clamping ring assembly (B in Figure 5) and cable gland base (A in Figure 5).Figure 5: RJ-45 cable and cable gland assembly2Use a wide flat-blade screwdriver to remove the blanking cap from the AP.3Connect the cable to the Ethernet port in the AP. 4Tighten the cable gland base into the AP chassis to 7 N.m or 62 in-lbs.5Wrap the clamping ring assembly around the rubber sealing insert. Make sure that the clamping ring assembly fully encloses the rubber sealing insert.6Seat the clamping ring assembly and rubber sealing insert in the cable gland base.7Hand-tighten the sealing nut until the rubber sealing insert is compressed. 8Continue with Step 2a: Attaching the Mounting Bracket to a Flat Surface or Step 2b: Attaching the Mounting Bracket to a Metal Pole.Limited ReachGood ReachExcellentReachExcellentReachOption 1Option 2GoodReachExcellentReachExcellentReachLimitedReachAzimuth Plane CoverageExcellentReach ExcellentReachExcellentReachABCD
Download:
Mirror Download [FCC.gov]
Document ID2287300
Application IDyAQDZ8d6bp+kdtJcd5XbYw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize55.78kB (697201 bits)
Date Submitted2014-06-05 00:00:00
Date Available2014-12-03 00:00:00
Creation Date2017-10-22 12:19:09
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-10-22 12:19:09
Document TitleUser Manual
Document CreatorAdobe Acrobat Pro 10.1.9
Document Author: Ruckus Wireless, Inc.
FCC ID Filing: S9GT300

Navigation menu